Wear Strips Categories

There is also a good range of Balls - Ceramic - Zirconia on the Small Parts and Bearings website.

Washers - Thrust - DP4 Type

Also see combined categories:
All Thrust Washers

Wear resistant helping to prevent wear deposits in the lubricating oil after long working periods. Designed for use in oil pumps and dampers.

Operating Temperature -200^o to 280^o Celsius. Maximum load 250N per mm2. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free. This category may be available in the new MBA online store at Washers - Thrust - DP4 Type.

There is also a good range of Washers - Thrust - DP4 Type on the Small Parts and Bearings website.

Balls - Ceramic - Silicon Nitride

Also see combined categories:
All Ceramic Balls
All Non Metallic Balls

Outstanding wear resistance. Good thermal and chemical resistance.

High hardness. Grades shown are AFBMA / ISO3290-1. High strength over a wide temperature range. High fracture toughness. Outstanding wear resistance. Good thermal and chemical resistance.

Related Information:

There is also a good range of Balls - Ceramic - Silicon Nitride on the Small Parts and Bearings website.

Bushes - Plastic Flanged - Iglidur J

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 ^oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic Flanged - Iglidur J on the Small Parts and Bearings website.

Bushes - Plastic Flanged - Iglidur Q

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Excellent wear resistance under high load. Resistant to dirt.

Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 ^oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic Flanged - Iglidur Q on the Small Parts and Bearings website.

Bushes - Plastic Unflanged - Iglidur J

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Related Information:

There is also a good range of Bushes - Plastic Unflanged - Iglidur J on the Small Parts and Bearings website.

Bushes - Split - Steel - DP4 - Flanged

Also see combined categories:
All Steel Bushes
All Flanged Steel Bushes

Wear resistant helping to prevent wear deposits in the lubricating oil after long working periods. Designed for use in oil pumps and dampers.

Operating Temperature -200^o to 280^o Celsius. Maximum load 250N/mm2. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free. Speed Limit in oil 3 metres surface speed per second.

Related Information:

There is also a good range of Bushes - Split - Steel - DP4 - Flanged on the Small Parts and Bearings website.

Balls - Ceramic - Ruby - Synthetic

Also see combined categories:
All Ceramic Balls
All Non Metallic Balls

Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.

Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Specific Gravity: 3.98.

Related Information:

There is also a good range of Balls - Ceramic - Ruby - Synthetic on the Small Parts and Bearings website.

Balls - Ceramic - Sapphire - Synthetic

Also see combined categories:
All Ceramic Balls
All Non Metallic Balls

Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.

Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Specific Gravity: 3.98. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Transparent (refractive index 1.76).

Related Information:

There is also a good range of Balls - Ceramic - Sapphire - Synthetic on the Small Parts and Bearings website.

Balls - Metallic - Tungsten Carbide

Also see combined categories:
All Metallic Balls

Extreme hardness and wear resistance.

Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Precision Grade: Grade 25. Hardness: Rockwell A: 91.5 (Approx 77 Rockwell C). Extreme hardness and wear resistance. Specific Gravity: 14.95.

Related Information:

There is also a good range of Balls - Metallic - Tungsten Carbide on the Small Parts and Bearings website.

Bushes - Plastic Flanged - Iglidur W300

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 ^oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic Flanged - Iglidur W300 on the Small Parts and Bearings website.

Bushes - Plastic Unflanged - Iglidur W300

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Related Information:

There is also a good range of Bushes - Plastic Unflanged - Iglidur W300 on the Small Parts and Bearings website.

Rollers - Yoke - Cam - Urethane Coated

Also see combined categories:
All Rollers

Urethane tyred cam yoke rollers for noise reduction, reduced wear and non marking. 80 Shore A hardness.

Polycoated shore 80A cast urethane cover. This category may be available in the new MBA online store at Rollers - Yoke - Cam - Urethane Coated.

Related Information:

Bushes - Plastic Unflanged - Iglidur H370

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.

Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 ^oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

Precision Shafting To Suit Bearings

There is also a good range of Bushes - Plastic Unflanged - Iglidur H370 on the Small Parts and Bearings website.

Cam Followers - Roller Type - Urethane Covered

Also see combined categories:
All Cam Followers

Urethane tyred cam followers for noise reduction, reduced wear and non marking

This category may be available in the new MBA online store at Cam Followers - Roller Type - Urethane Covered.

There is also a good range of Cam Followers - Roller Type - Urethane Covered on the Small Parts and Bearings website.

Ball Buttons

Also known as striker bushings or ball plunger detents. Use with ball or bolt spring plungers for a hard wearing contact area.

Burnished ground hardened steel. This category may be available in the new MBA online store at Ball Buttons.

There is also a good range of Ball Buttons on the Small Parts and Bearings website.

Mounts - Levelling Studded - Plated - Standard

Also see combined categories:
All Male Stud Levelers

Levelling adjusters. Good quality with value pricing. Hardened ball for high load ratings and excellent wear characteristics.

Large diameter base for added support. 15^o off centre swivel for quick leveling on sloped surfaces. This category may be available in the new MBA online store at Mounts - Levelling Studded - Plated - Standard.

There is also a good range of Mounts - Levelling Studded - Plated - Standard on the Small Parts and Bearings website.

Bearings - One Way Sprag - Standard

Also see combined categories:
All One Way Clutch Bearings

Sprag clutch bearings allow your application to turn one way whilst locking in the opposite direction.

Designed for press fit installation. Correct interference dimensions must be maintained to obtain maximum bearing and clutch performance. Mount the clutch ensuring that the shaft drive directionis in the direction indicated by the arrow on the inner race. To install, use a press tool / do not hammer or apply other stock to clutch. Make sure housing has enough strength to withstand press required for fitting installation. High carbon hardened steel alloy. Always lock out power switch before installing, removing, lubricating or servicing a system that uses Cam Clutch products. When connecting or disconnecting Cam Clutch products, eye protection is required. Wear safety glasses, protective clothing, gloves and safety shoes.

Related Information:

There is also a good range of Bearings - One Way Sprag - Standard on the Small Parts and Bearings website.

Inserts - Self Tapping - For Wood - Slotted Drive - Standard

Also see combined categories:
All Self Tapping Inserts
All Self Tapping Inserts for Wood

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60^o countersink is required for flush mounting. Use with soft plastics, hard and soft wood, particle board.

Related Information:

There is also a good range of Inserts - Self Tapping - For Wood - Slotted Drive - Standard on the Small Parts and Bearings website.

Bushings - Tension

Like a heavy duty roll pin.

Made of a high carbon spring steel with high elasticity, resilience and wear characteristics. Designed to replace solid steel tubular and case hardened bushings because they are close tolerance, self-retaining and through hard. Insertion can be easily accomplished with a hammer and drift. Ideal for high load/low-speed operation in articulating or continuous applications. This category may be available in the new MBA online store at Bushings - Tension.

There is also a good range of Bushings - Tension on the Small Parts and Bearings website.

Inserts - Self Tapping - For Aluminium - Stainless 303

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60^o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.

Related Information:

There is also a good range of Inserts - Self Tapping - For Aluminium - Stainless 303 on the Small Parts and Bearings website.

Inserts - Self Tapping - For Plastics - Steel

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Related Information:

There is also a good range of Inserts - Self Tapping - For Plastics - Steel on the Small Parts and Bearings website.

Inserts - Self Tapping - For Aluminium - Stainless 316

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60^o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or hard plastics. Made from 316 stainless steel.

Related Information:

There is also a good range of Inserts - Self Tapping - For Aluminium - Stainless 316 on the Small Parts and Bearings website.

Inserts - Self Tapping - For Aluminium - Steel

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60^o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.

Related Information:

There is also a good range of Inserts - Self Tapping - For Aluminium - Steel on the Small Parts and Bearings website.

Housings - Flanged 2 Bolt Hole - W300

Also see combined categories:
All Housings with Integral Bearing

With integral self aligning plain bearing.

Housing: Igumid G. Ball: Highly wear resistant Iglidur W300. This category may be available in the new MBA online store at Housings - Flanged 2 Bolt Hole - W300.

There is also a good range of Housings - Flanged 2 Bolt Hole - W300 on the Small Parts and Bearings website.

Bushes - Brass Flanged - Graphite Plug

Also see combined categories:
All Bronze Bushes
All Flanged Bronze Bushes

Used for dies, moulds and heavy machinery. Brass Alloy.

High-Tensile Brass Alloy. Suitable for use under conditions of heavy load and low speed operation. Solid Lubricant Plugs. Excellent wear resistance can be exerted at parts with reciprocating motion, frequent starting and stopping, etc., where oil film is difficult to form. Class 7 precision ID. 29N per mm sq max allowable load with max allowable speed 0.5m per second unlubricated and 1m per second lubricated.

Related Information:

There is also a good range of Bushes - Brass Flanged - Graphite Plug on the Small Parts and Bearings website.

Bushes - Brass Unflanged - Graphite Plug

Also see combined categories:
All Bronze Bushes
All Unflanged Bronze Bushes

Used for dies, moulds and heavy machinery. Brass Alloy.

Related Information:

There is also a good range of Bushes - Brass Unflanged - Graphite Plug on the Small Parts and Bearings website.

Inserts - Self Tapping - For Plastics - Stainless Steel

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Use of installation tool recommended. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60^o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Standard made from 303 stainless steel. Quantity orders can also be supplied in Brass or 316 Stainless.

Related Information:

There is also a good range of Inserts - Self Tapping - For Plastics - Stainless Steel on the Small Parts and Bearings website.

Bushes - Plastic Clip - Double Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

For use with sheet metal. Used as a light duty split bearing.

Low clearance. Maintenance free. Economical. High Precision. High wear resistance. Light weight. M250 Polymer minus 40 ^oC to 80 ^oC (minus 40 Deg F to 176 Deg F). This category may be available in the new MBA online store at Bushes - Plastic Clip - Double Flanged.

Related Information:

There is also a good range of Bushes - Plastic Clip - Double Flanged on the Small Parts and Bearings website.

Bearings - Angular Contact - Single Row Ball - Ceramic ZRO2

Also see combined categories:
All Angular Contact Bearings
All Full Ceramic Bearings

Excellent performance in electrical and magnetism sensitive applications. Full ceramic zirconia.

Applications include cryopumps, medical applications, semiconductors, turbine flow meters, food processing, robotics and optics. Wear and corrosion resistance. Depending on the application, these bearings may run lubrication free or lubricated by the medium in which they are submerged. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. ZrO2 standard material for balls and rings. Si3N4 available to special order. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage. Up to 1000 deg C without a cage or seals.

Related Information:

There is also a good range of Bearings - Angular Contact - Single Row Ball - Ceramic ZRO2 on the Small Parts and Bearings website.

Springs - Constant Force

301 Stainless Steel

Mounting hole specifications will be supplied on request. These springs are usually mounted on a drum and the free end attached to a loading force like a counterbalance. Free ID may vary to meet load specification. Load capacity can be increased by using multiple strips in tandem, back to back or laminated. Be sure to leave at least 40mm coiled on the drum at full extension. The spring ID will wrap tightly on the drum so that most applications require no fastening to the drum. This category may be available in the new MBA online store at Springs - Constant Force.

Related Information:

Technical

There is also a good range of Springs - Constant Force on the Small Parts and Bearings website.

Bearings - Double Row Ball - Self Aligning - Ceramic ZrO2

Also see combined categories:
All Radial Ball Bearings
All Full Ceramic Bearings

Excellent performance in electrical and magnetism sensitive applications. Not for High Speed. Full ceramic zirconia.

Applications include cryopumps, medical applications, semiconductors, turbine flow meters, food processing, robotics and optics. Wear and corrosion resistance. Lubrication and maintenance free. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. ZrO2 standard material for balls and rings. Si3N4 available to special order. High and low temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage. Up to 1000 deg C without a cage or seals.

Related Information:

There is also a good range of Bearings - Double Row Ball - Self Aligning - Ceramic ZrO2 on the Small Parts and Bearings website.

Bearings - Single Row Ball Unflanged - Standard - Ceramic ZrO2

Also see combined categories:
All Radial Ball Bearings
All Full Ceramic Bearings

Excellent performance in electrical and magnetism sensitive applications. Not for High Speed. Full ceramic zirconia.

Related Information:

There is also a good range of Bearings - Single Row Ball Unflanged - Standard - Ceramic ZrO2 on the Small Parts and Bearings website.

Rod - Drill - S-7 Air Hardening

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

Air hardening molybdenum, chromium, shock resisting. High impact strength with moderate wear resistance. 95 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for S-7 hardening requirements. This category may be available in the new MBA online store at Rod - Drill - S-7 Air Hardening.

There is also a good range of Rod - Drill - S-7 Air Hardening on the Small Parts and Bearings website.

Bearings - Angular Contact - Single Row Ball - Ceramic Si3N4

Also see combined categories:
All Angular Contact Bearings
All Full Ceramic Bearings

Excellent performance in electrical and magnetism sensitive applications. Higher speed than Zr02. Full ceramic silicon nitride.

Applications include cryopumps, medical applications, semiconductors, turbine flow meters, food processing, robotics and optics. Wear and corrosion resistance. Lubrication and maintenance free. 3.2g/cubic cm density. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. Si3N4 (GSN-201) standard material for balls and rings. HRC80 Hardness. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage. Up to 700 deg C without a cage or seals.

Related Information:

Bearings - Single Row Ball Unflanged - Standard - Ceramic Si3N4

Also see combined categories:
All Radial Ball Bearings
All Full Ceramic Bearings

Excellent performance in electrical and magnetism sensitive applications. Higher speed than Zr02. Full ceramic silicon nitride.

Applications include cryopumps, medical applications, semiconductors, turbine flow meters, food processing, robotics and optics. Wear and corrosion resistance. Lubrication and maintenance free. 3.2g/cubic cm density. Wear and corrosion resistance. Depending on the application, these bearings may run lubrication free or lubricated by the medium in which they are submerged. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. Si3N4 (GSN-201) standard material for balls and rings. HRC80 Hardness. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage. Up to 700 deg C without a cage or seals.

Related Information:

Cable Attachments - Thimbles - Stainless Steel

316 Stainless Steel. Use with synchromesh cable or standard miniature cable. Use with synchromesh or standard miniature cable

Thimbles provide loop support at higher loads and protect cables from wear when motion is present. Some thimbles may have open or uneven ends. This category may be available in the new MBA online store at Cable Attachments - Thimbles - Stainless Steel.

Related Information:

Synchromesh Info

Cable

There is also a good range of Cable Attachments - Thimbles - Stainless Steel on the Small Parts and Bearings website.

Slides - Dovetail

Also see combined categories:
All Linear Slides

Used for work feeders for production milling, positioning fixutres, work holding devices, checking fixtures, shuttle devices, assembly equipment, etc.

Tapered gibs are adjusted with a single screw that moves the gib on the taper. This type remains parallel and wears less as it occurs over the entire surface. Made of continuous cast GS 40,000 PSI pearlitic grey iron. Able to be milled, drilled, tapped, etc. This category may be available in the new MBA online store at Slides - Dovetail.

There is also a good range of Slides - Dovetail on the Small Parts and Bearings website.

Bushes - Plastic Clip - Bevelled Edge

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

M250 Polymer minus 40 Deg C to 80 Deg C (minus 40 Deg F to 176 Deg F). Used as a light duty split bearing.

Low clearance. Maintenance free. Economical. High Precision. High wear resistance. Light weight. This category may be available in the new MBA online store at Bushes - Plastic Clip - Bevelled Edge.

Related Information: