Miniature Bearings Australia Pty Ltd

Washers Flat Plastic Categories


Washers - Flat - PVC
Washers - Flat - PVC

Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic

Flat washers.

This category may be available in the new MBA online store at Washers - Flat - PVC.

Related Information:

There is also a good range of Washers - Flat - PVC on the Small Parts and Bearings website.


Washers - Flat - Nylon
Washers - Flat - Nylon

Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic

Flat washers.

Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD. This category may be available in the new MBA online store at Washers - Flat - Nylon.

Related Information:

There is also a good range of Washers - Flat - Nylon on the Small Parts and Bearings website.


Washers - Flat - PTFE - Precision Shim
Washers - Flat - PTFE - Precision Shim

Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic

Teflon Washers

This category may be available in the new MBA online store at Washers - Flat - PTFE - Precision Shim.

Related Information:

There is also a good range of Washers - Flat - PTFE - Precision Shim on the Small Parts and Bearings website.


You may also be interested in

Springs Disc


Washers - Disc Spring - Plastic
Washers - Disc Spring - Plastic

Also see combined categories:
All Disc Springs

Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb(R) material.

There is also a good range of Washers - Disc Spring - Plastic on the Small Parts and Bearings website.


Pins - Locating - Spring - Plastic Pin - Sealed
Pins - Locating - Spring - Plastic Pin - Sealed

Also see combined categories:
All Locating Pins

Aluminium Body. For fixturing small parts in tight areas. Ideal for positioning and chucking flat or round parts for profile clamping.

This category may be available in the new MBA online store at Pins - Locating - Spring - Plastic Pin - Sealed.

Related Information:

There is also a good range of Pins - Locating - Spring - Plastic Pin - Sealed on the Small Parts and Bearings website.


Pins - Locating - Spring - Plastic Pin - Unsealed
Pins - Locating - Spring - Plastic Pin - Unsealed

Also see combined categories:
All Locating Pins

Aluminium Body. For fixturing small parts in tight areas. Ideal for positioning and chucking flat or round parts for profile clamping.

This category may be available in the new MBA online store at Pins - Locating - Spring - Plastic Pin - Unsealed.

Related Information:

There is also a good range of Pins - Locating - Spring - Plastic Pin - Unsealed on the Small Parts and Bearings website.


Pins - Hammer Drive - Flat Head
Pins - Hammer Drive - Flat Head

Also see combined categories:
All Hammer Drive Pins

Used to replace screws where the need to remove the pin is unlikely.

Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.

Related Information:

There is also a good range of Pins - Hammer Drive - Flat Head on the Small Parts and Bearings website.


Washers - Flat - Fibre
Washers - Flat - Fibre

Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic

Flat red vulcanised fibre washers. Black available on request and sufficient quantity.

Operating temperature up to 105 oC. Tensile strength 6 kg/mm2. Elongation up to 19 percent. Shrinkage up to 3 percent thickness. Water absorption 4 to 70 percent after 24 hours. Density 1 to 1.45 g/cm.

Related Information:

There is also a good range of Washers - Flat - Fibre on the Small Parts and Bearings website.


Washers - Flat - Aluminium - Precision Shim
Washers - Flat - Aluminium - Precision Shim

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers.

This category may be available in the new MBA online store at Washers - Flat - Aluminium - Precision Shim.

Related Information:

There is also a good range of Washers - Flat - Aluminium - Precision Shim on the Small Parts and Bearings website.


Washers - Flat - Brass - Commercial
Washers - Flat - Brass - Commercial

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers.

Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD. This category may be available in the new MBA online store at Washers - Flat - Brass - Commercial.

Related Information:

There is also a good range of Washers - Flat - Brass - Commercial on the Small Parts and Bearings website.


Washers - Flat - Brass - Precision Shim
Washers - Flat - Brass - Precision Shim

Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Precision Tolerances. Standard and laminated brass shim washers.

This category may be available in the new MBA online store at Washers - Flat - Brass - Precision Shim.

Related Information:

There is also a good range of Washers - Flat - Brass - Precision Shim on the Small Parts and Bearings website.


Washers - Flat - Carbon Spring Steel - Precision Shim
Washers - Flat - Carbon Spring Steel - Precision Shim

Also see combined categories:
All Precision Shim Washers
All Flat Washers and Spacers - Metallic

Flat Carbon Spring Steel Washers. Commonly used for fast and accurate spacing of milling cutters, gang cutters, saws, slitting blades and grinding tools.

C1010 steel types best suited to arbor shimming. This category may be available in the new MBA online store at Washers - Flat - Carbon Spring Steel - Precision Shim.

Related Information:

There is also a good range of Washers - Flat - Carbon Spring Steel - Precision Shim on the Small Parts and Bearings website.


Washers - Flat - Copper - Precision Shim
Washers - Flat - Copper - Precision Shim

Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Precision Tolerances.

This category may be available in the new MBA online store at Washers - Flat - Copper - Precision Shim.

Related Information:

There is also a good range of Washers - Flat - Copper - Precision Shim on the Small Parts and Bearings website.


Washers - Flat - Hardened Steel
Washers - Flat - Hardened Steel

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Medium carbon steel through hardened to RC 43-49. Zinc dichromate finish. All dimensions shows are minimum.

This category may be available in the new MBA online store at Washers - Flat - Hardened Steel.

Related Information:

There is also a good range of Washers - Flat - Hardened Steel on the Small Parts and Bearings website.


Washers - Flat - High Tensile
Washers - Flat - High Tensile

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Grade 8 high tensile washers

ASTM F436 1985. Please note! Tolerances for commercial grade washers are much larger than for precision washers. This category may be available in the new MBA online store at Washers - Flat - High Tensile.

Related Information:

There is also a good range of Washers - Flat - High Tensile on the Small Parts and Bearings website.


Washers - Flat - Mild Steel
Washers - Flat - Mild Steel

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers. Includes fender washers. Zinc plated and unplated listings.

In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD. This category may be available in the new MBA online store at Washers - Flat - Mild Steel.

Related Information:

There is also a good range of Washers - Flat - Mild Steel on the Small Parts and Bearings website.


Washers - Flat - Sintered Bronze - Precision
Washers - Flat - Sintered Bronze - Precision

Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat thrust washers made from oil impregnated sintered bronze

This category may be available in the new MBA online store at Washers - Flat - Sintered Bronze - Precision.

Related Information:

There is also a good range of Washers - Flat - Sintered Bronze - Precision on the Small Parts and Bearings website.


Washers - Flat - Stainless Steel 304 - Commercial
Washers - Flat - Stainless Steel 304 - Commercial

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers.

Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers. This category may be available in the new MBA online store at Washers - Flat - Stainless Steel 304 - Commercial.

Related Information:

There is also a good range of Washers - Flat - Stainless Steel 304 - Commercial on the Small Parts and Bearings website.


Washers - Flat - Stainless Steel 316 - Commercial
Washers - Flat - Stainless Steel 316 - Commercial

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers.

Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers. This category may be available in the new MBA online store at Washers - Flat - Stainless Steel 316 - Commercial.

Related Information:

There is also a good range of Washers - Flat - Stainless Steel 316 - Commercial on the Small Parts and Bearings website.


Washers - Flat - Stainless Steel - Precision Shim
Washers - Flat - Stainless Steel - Precision Shim

Also see combined categories:
All Precision Shim Washers
All Flat Washers and Spacers - Metallic

Precision Tolerances.

This category may be available in the new MBA online store at Washers - Flat - Stainless Steel - Precision Shim.

Related Information:

There is also a good range of Washers - Flat - Stainless Steel - Precision Shim on the Small Parts and Bearings website.


Washers - Flat - Stamped - Heavy Duty - Hardened
Washers - Flat - Stamped - Heavy Duty - Hardened

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Heat treated. Black oxide finish.

This category may be available in the new MBA online store at Washers - Flat - Stamped - Heavy Duty - Hardened.

Related Information:

There is also a good range of Washers - Flat - Stamped - Heavy Duty - Hardened on the Small Parts and Bearings website.


Washers - Flat - Titanium - CP Grade 1
Washers - Flat - Titanium - CP Grade 1

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.

Commercially pure for general industrial corrosion applications. UNS R50250. Please note! Tolerances for commercial grade washers are much larger than for precision washers. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance. This category may be available in the new MBA online store at Washers - Flat - Titanium - CP Grade 1.

Related Information:

There is also a good range of Washers - Flat - Titanium - CP Grade 1 on the Small Parts and Bearings website.


Washers - Flat - Rubber
Washers - Flat - Rubber

Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic

Nitrile Duro 70

This category may be available in the new MBA online store at Washers - Flat - Rubber.

Related Information:

There is also a good range of Washers - Flat - Rubber on the Small Parts and Bearings website.


Washers - C - Steel
Washers - C - Steel

Also see combined categories:
All C Washers

Cold finished steel, case hardened with a black oxide finish.

This category may be available in the new MBA online store at Washers - C - Steel.

There is also a good range of Washers - C - Steel on the Small Parts and Bearings website.


Washers - C - Swing
Washers - C - Swing


Cold finished steel, hardened and ground. Black oxide finish.

This category may be available in the new MBA online store at Washers - C - Swing.

There is also a good range of Washers - C - Swing on the Small Parts and Bearings website.


Washers - Heavy Duty - Machined - Steel
Washers - Heavy Duty - Machined - Steel

Also see combined categories:
All Flat Washers and Spacers - Metallic

Case hardened cold finished steel with black oxide finish.

This category may be available in the new MBA online store at Washers - Heavy Duty - Machined - Steel.

Related Information:

There is also a good range of Washers - Heavy Duty - Machined - Steel on the Small Parts and Bearings website.


Washers - Heavy Duty - Machined - Stainless Steel
Washers - Heavy Duty - Machined - Stainless Steel

Also see combined categories:
All Flat Washers and Spacers - Metallic

303 Stainless Steel

This category may be available in the new MBA online store at Washers - Heavy Duty - Machined - Stainless Steel.

Related Information:

There is also a good range of Washers - Heavy Duty - Machined - Stainless Steel on the Small Parts and Bearings website.


Screws - Thumb - Flat Key Head - Washer Face - Steel
Screws - Thumb - Flat Key Head - Washer Face - Steel

Also see combined categories:
All Thumb Screws

Flat Key head malleable iron screws with an integral washer

This category may be available in the new MBA online store at Screws - Thumb - Flat Key Head - Washer Face - Steel.

Related Information:

There is also a good range of Screws - Thumb - Flat Key Head - Washer Face - Steel on the Small Parts and Bearings website.


Spacers - Arbor
Spacers - Arbor


Flat arbor shim washers with keyway groove.

This category may be available in the new MBA online store at Spacers - Arbor.

There is also a good range of Spacers - Arbor on the Small Parts and Bearings website.


Bearings - Thrust - Ball - Flat - Chrome Steel
Bearings - Thrust - Ball - Flat - Chrome Steel

Also see combined categories:
All Ball Thrust Bearings

3 Piece Thrust Bearings Open Type with Flat Washers

These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at Bearings - Thrust - Ball - Flat - Chrome Steel.

Related Information:

There is also a good range of Bearings - Thrust - Ball - Flat - Chrome Steel on the Small Parts and Bearings website.


Bearings - Thrust - Ball - Flat - Stainless Steel
Bearings - Thrust - Ball - Flat - Stainless Steel

Also see combined categories:
All Ball Thrust Bearings

3 Piece Thrust Bearings Open Type with Flat Washers

These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at Bearings - Thrust - Ball - Flat - Stainless Steel.

Related Information:

There is also a good range of Bearings - Thrust - Ball - Flat - Stainless Steel on the Small Parts and Bearings website.


Washers - Self Aligning - Components - Hardened Steel
Washers - Self Aligning - Components - Hardened Steel

Also see combined categories:
All Thrust Washers
All Aligning Washers

Spherical Seat Washers. Washer A (aligning) and washer B (seat) sold separately.

Case Hardened steel 9 S Mn Pb 28 K DIN 6319. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-G washers are used for clamping mechanical parts with non-parallel surfaces. Designed for screw solidity in compliance with 8.8. Limited for use on flat closed ring areas - not for elongated holes.

There is also a good range of Washers - Self Aligning - Components - Hardened Steel on the Small Parts and Bearings website.


Balls - Plastic - Acetal
Balls - Plastic - Acetal

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

High intensity strength, rigidity, outstanding resistance to abrasion and most solvents.

Tolerances available on request. Acetal Copolymer. High intensity strength, rigidity, outstanding resistance to abrasion and most solvents. Standard Opaque White. Specific Gravity: 1.4.

Related Information:

There is also a good range of Balls - Plastic - Acetal on the Small Parts and Bearings website.


Balls - Plastic - PVC
Balls - Plastic -  PVC

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

Polyvinyl chloride. PVC is a chemically stable material, which shows little change in molecular structure, and also exhibits little change in its mechanical strength.

Polyvinyl chloride is a widely used and inexpensive thermoplastic polymer. It is easily worked or machined and has good chemical and biological resistance. It is relatively hard and can be polished to a shine. Polyvinyl chloride is a widely used and inexpensive thermoplastic polymer. Heat Deflection Temperature 176 F / 80 C. Rockwell Hardness 115. Zero water absorption in 24 hours.

Related Information:

There is also a good range of Balls - Plastic - PVC on the Small Parts and Bearings website.


Bushes - Plastic - Acetal - Oil Impregnated
Bushes - Plastic - Acetal - Oil Impregnated

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Oil impregnated acetal with self-lubricating characteristics.

This category may be available in the new MBA online store at Bushes - Plastic - Acetal - Oil Impregnated.

Related Information:

There is also a good range of Bushes - Plastic - Acetal - Oil Impregnated on the Small Parts and Bearings website.


Balls - Plastic - Bored
Balls - Plastic - Bored

Also see combined categories:
All Plastic Balls - Bored

Bored acetal balls as used in plastic rod ends.

Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight. This category may be available in the new MBA online store at Balls - Plastic - Bored.

Related Information:

There is also a good range of Balls - Plastic - Bored on the Small Parts and Bearings website.


Shim - Plastic
Shim - Plastic

Also see combined categories:
All Shim
All Non Metallic Sheet

Easy to cut - colour coded - plastic shim sheets. Precision thicknesses.

NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Made from sturdy polyester. This category may be available in the new MBA online store at Shim - Plastic.

Related Information:

There is also a good range of Shim - Plastic on the Small Parts and Bearings website.


Threaded Rod - Allthread - Plastic
Threaded Rod - Allthread - Plastic

Also see combined categories:
All Threaded Rod

UNC - UNF - METRIC - Nylon and PVC. Also known as booker rod.

Light Weight. Non Corrosive. Vibration Resistant. This category may be available in the new MBA online store at Threaded Rod - Allthread - Plastic.

There is also a good range of Threaded Rod - Allthread - Plastic on the Small Parts and Bearings website.


Bearings - Acetal - Solid - For Plastic Housings
Bearings - Acetal - Solid - For Plastic Housings


Insert bearings ideal for wet conditions. Similar to wide inner ring bearings for P, F, Fl type housings but solid plastic.

Load and speed calculations are for reference only. Testing is recommended. This category may be available in the new MBA online store at Bearings - Acetal - Solid - For Plastic Housings.

Related Information:

There is also a good range of Bearings - Acetal - Solid - For Plastic Housings on the Small Parts and Bearings website.


Gears - Mitre - Module 0.5 - Plastic
Gears - Mitre - Module 0.5 - Plastic

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Acetal

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 0.5 - Plastic.

Related Information:

There is also a good range of Gears - Mitre - Module 0.5 - Plastic on the Small Parts and Bearings website.


Gears - Mitre - Module 1 - Plastic
Gears - Mitre - Module 1 - Plastic

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Acetal.

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 1 - Plastic.

Related Information:

There is also a good range of Gears - Mitre - Module 1 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.4 - Plastic
Gears - Spur - Module 0.4 - Plastic

Also see combined categories:
All Module 0.4 Spur Gears
All Plastic Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.4 - Plastic.

There is also a good range of Gears - Spur - Module 0.4 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.5 - Plastic
Gears - Spur - Module 0.5 - Plastic

Also see combined categories:
All Module 0.5 Spur Gears
All Plastic Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.5 - Plastic.

There is also a good range of Gears - Spur - Module 0.5 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.7 - Plastic
Gears - Spur - Module 0.7 - Plastic


PCD = No. of Teeth x 0.700mm. 20o Pressure Angle. Acetal.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.7 - Plastic.

There is also a good range of Gears - Spur - Module 0.7 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.8 - Plastic
Gears - Spur - Module 0.8 - Plastic

Also see combined categories:
All Module 0.8 Spur Gears
All Plastic Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Plastic.

There is also a good range of Gears - Spur - Module 0.8 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 1.5 - Plastic
Gears - Spur - Module 1.5 - Plastic

Also see combined categories:
All Module 1.5 Spur Gears
All Plastic Module 1.5 Spur Gears

PCD = No. of Teeth x 1.500mm. 20o Pressure Angle. Acetal and Nylon

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 1.5 - Plastic.

There is also a good range of Gears - Spur - Module 1.5 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 1 - Plastic
Gears - Spur - Module 1 - Plastic

Also see combined categories:
All Module 1.0 Spur Gears
All Plastic Module 1.0 Spur Gears

PCD = No. of Teeth x 1.000mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 1 - Plastic.

There is also a good range of Gears - Spur - Module 1 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.4 - Plastic with Insert
Gears - Spur - Module 0.4 - Plastic with Insert

Also see combined categories:
All Module 0.4 Spur Gears
All Plastic Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.4 - Plastic with Insert.

There is also a good range of Gears - Spur - Module 0.4 - Plastic with Insert on the Small Parts and Bearings website.


Gears - Spur - Module 0.5 - Plastic with Insert
Gears - Spur - Module 0.5 - Plastic with Insert

Also see combined categories:
All Module 0.5 Spur Gears
All Plastic Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.5 - Plastic with Insert.

There is also a good range of Gears - Spur - Module 0.5 - Plastic with Insert on the Small Parts and Bearings website.


Gears - Spur - Module 0.8 - Plastic with Insert
Gears - Spur - Module 0.8 - Plastic with Insert

Also see combined categories:
All Module 0.8 Spur Gears
All Plastic Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Plastic with Insert.

There is also a good range of Gears - Spur - Module 0.8 - Plastic with Insert on the Small Parts and Bearings website.





Main Pages

5 Axis Machine Tool Bearings About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Distributor Locations Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Satellite Reaction Wheels Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 229438 products in 2170 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 229438 products in 2170 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.