Miniature Bearings Australia Pty Ltd

Washers Flat Plastic Categories


Washers - Flat - Nylon
Washers - Flat - Nylon

Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic

Flat washers.

Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.

Related Information:

There is also a good range of Washers - Flat - Nylon on the Small Parts and Bearings website.


Washers - Flat - PVC
Washers - Flat - PVC

Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic

Flat washers.


Related Information:

There is also a good range of Washers - Flat - PVC on the Small Parts and Bearings website.


Washers - Flat - PTFE
Washers - Flat - PTFE

Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic

Teflon Washers


Related Information:

There is also a good range of Washers - Flat - PTFE on the Small Parts and Bearings website.


You may also be interested in

Springs Disc


Washers - Disc Spring - Plastic
Washers - Disc Spring - Plastic

Also see combined categories:
All Disc Springs

Also known as belleville washers.

Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb(R) material.

There is also a good range of Washers - Disc Spring - Plastic on the Small Parts and Bearings website.


Bearings Thrust


Washers - Self Aligning - Sets - Plastic
Washers - Self Aligning - Sets - Plastic

Also see combined categories:
All Thrust Washers
All Aligning Washers

Spherical Seat Washers

Tensile strengths shown are Static Axial in Newtons. Easy to install. Good friction wear properties.

Related Information:

There is also a good range of Washers - Self Aligning - Sets - Plastic on the Small Parts and Bearings website.


Pins - Locating - Spring - Plastic Pin - Sealed
Pins - Locating - Spring - Plastic Pin - Sealed

Also see combined categories:
All Locating Pins

Aluminium Body. For fixturing small parts in tight areas. Ideal for positioning and chucking flat or round parts for profile clamping.


Related Information:

There is also a good range of Pins - Locating - Spring - Plastic Pin - Sealed on the Small Parts and Bearings website.


Pins - Locating - Spring - Plastic Pin - Unsealed
Pins - Locating - Spring - Plastic Pin - Unsealed

Also see combined categories:
All Locating Pins

Aluminium Body. For fixturing small parts in tight areas. Ideal for positioning and chucking flat or round parts for profile clamping.


Related Information:

There is also a good range of Pins - Locating - Spring - Plastic Pin - Unsealed on the Small Parts and Bearings website.


Pins - Hammer Drive - Flat Head
Pins - Hammer Drive - Flat Head

Also see combined categories:
All Hammer Drive Pins

Used to replace screws where the need to remove the pin is unlikely.

Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.

Related Information:

There is also a good range of Pins - Hammer Drive - Flat Head on the Small Parts and Bearings website.


Washers - Flat - Fibre
Washers - Flat - Fibre

Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic

Flat red vulcanised fibre washers. Black available on request and sufficient quantity.

Operating temperature up to 105 oC. Tensile strength 6 kg/mm2. Elongation up to 19 percent. Shrinkage up to 3 percent thickness. Water absorption 4 to 70 percent after 24 hours. Density 1 to 1.45 g/cm.

Related Information:

There is also a good range of Washers - Flat - Fibre on the Small Parts and Bearings website.


Washers - Flat - Aluminium
Washers - Flat - Aluminium

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers.


Related Information:

There is also a good range of Washers - Flat - Aluminium on the Small Parts and Bearings website.


Washers - Flat - Brass - Commercial
Washers - Flat - Brass - Commercial

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers.

Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.

Related Information:

There is also a good range of Washers - Flat - Brass - Commercial on the Small Parts and Bearings website.


Washers - Flat - Brass - Precision
Washers - Flat - Brass - Precision

Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Precision Tolerances. Laminated brass shim washers.


Related Information:

There is also a good range of Washers - Flat - Brass - Precision on the Small Parts and Bearings website.


Washers - Flat - Carbon Spring Steel - Precision Shim
Washers - Flat - Carbon Spring Steel - Precision Shim

Also see combined categories:
All Precision Shim Washers
All Flat Washers and Spacers - Metallic

Flat Carbon Spring Steel Washers. Commonly used for fast and accurate spacing of milling cutters, gang cutters, saws, slitting blades and grinding tools.

C1010 steel types best suited to arbor shimming.

Related Information:

There is also a good range of Washers - Flat - Carbon Spring Steel - Precision Shim on the Small Parts and Bearings website.


Washers - Flat - Hardened Steel
Washers - Flat - Hardened Steel

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Medium carbon steel through hardened to RC 43-49. Zinc dichromate finish. All dimensions shows are minimum.


Related Information:

There is also a good range of Washers - Flat - Hardened Steel on the Small Parts and Bearings website.


Washers - Flat - High Tensile
Washers - Flat - High Tensile

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Grade 8 high tensile washers

ASTM F436 1985. Please note! Tolerances for commercial grade washers are much larger than for precision washers.

Related Information:

There is also a good range of Washers - Flat - High Tensile on the Small Parts and Bearings website.


Washers - Flat - Mild Steel
Washers - Flat - Mild Steel

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers. Includes fender washers. Zinc plated and unplated listings.

In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.

Related Information:

There is also a good range of Washers - Flat - Mild Steel on the Small Parts and Bearings website.


Washers - Flat - Sintered Bronze - Precision
Washers - Flat - Sintered Bronze - Precision

Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat thrust washers made from oil impregnated sintered bronze


Related Information:

There is also a good range of Washers - Flat - Sintered Bronze - Precision on the Small Parts and Bearings website.


Washers - Flat - Stainless Steel 304 - Commercial
Washers - Flat - Stainless Steel 304 - Commercial

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers.

Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.

Related Information:

There is also a good range of Washers - Flat - Stainless Steel 304 - Commercial on the Small Parts and Bearings website.


Washers - Flat - Stainless Steel 316 - Commercial
Washers - Flat - Stainless Steel 316 - Commercial

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers.

Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.

Related Information:

There is also a good range of Washers - Flat - Stainless Steel 316 - Commercial on the Small Parts and Bearings website.


Washers - Flat - Stainless Steel - Precision Shim
Washers - Flat - Stainless Steel - Precision Shim

Also see combined categories:
All Precision Shim Washers
All Flat Washers and Spacers - Metallic

Precision Tolerances.


Related Information:

There is also a good range of Washers - Flat - Stainless Steel - Precision Shim on the Small Parts and Bearings website.


Washers - Flat - Stamped - Heavy Duty - Hardened
Washers - Flat - Stamped - Heavy Duty - Hardened

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Heat treated. Black oxide finish.


Related Information:

There is also a good range of Washers - Flat - Stamped - Heavy Duty - Hardened on the Small Parts and Bearings website.


Washers - Flat - Titanium - CP Grade 1
Washers - Flat - Titanium - CP Grade 1

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.

Commercially pure for general industrial corrosion applications. UNS R50250. Please note! Tolerances for commercial grade washers are much larger than for precision washers. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance.

Related Information:

There is also a good range of Washers - Flat - Titanium - CP Grade 1 on the Small Parts and Bearings website.


Washers - Flat - Rubber
Washers - Flat - Rubber

Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic

Nitrile Duro 70


Related Information:

There is also a good range of Washers - Flat - Rubber on the Small Parts and Bearings website.


Washers - C - Steel
Washers - C - Steel

Also see combined categories:
All C Washers

Cold finished steel, case hardened with a black oxide finish.


There is also a good range of Washers - C - Steel on the Small Parts and Bearings website.


Washers - C - Swing
Washers - C - Swing


Cold finished steel, hardened and ground. Black oxide finish.


There is also a good range of Washers - C - Swing on the Small Parts and Bearings website.


Washers - C - 303 Stainless Steel
Washers - C - 303 Stainless Steel

Also see combined categories:
All C Washers

Knurled outside edge


There is also a good range of Washers - C - 303 Stainless Steel on the Small Parts and Bearings website.


Washers - Heavy Duty - Machined - Steel
Washers - Heavy Duty - Machined - Steel

Also see combined categories:
All Flat Washers and Spacers - Metallic

Case hardened cold finished steel with black oxide finish.


Related Information:

There is also a good range of Washers - Heavy Duty - Machined - Steel on the Small Parts and Bearings website.


Washers - Heavy Duty - Machined - Stainless Steel
Washers - Heavy Duty - Machined - Stainless Steel

Also see combined categories:
All Flat Washers and Spacers - Metallic

303 Stainless Steel


Related Information:

There is also a good range of Washers - Heavy Duty - Machined - Stainless Steel on the Small Parts and Bearings website.


Screws - Thumb - Flat Key Head - Washer Face - Steel
Screws - Thumb - Flat Key Head - Washer Face - Steel

Also see combined categories:
All Thumb Screws

Flat Key head malleable iron screws with an integral washer


There is also a good range of Screws - Thumb - Flat Key Head - Washer Face - Steel on the Small Parts and Bearings website.


Spacers - Arbor
Spacers - Arbor


Flat arbor shim washers with keyway groove.


There is also a good range of Spacers - Arbor on the Small Parts and Bearings website.


Handles - Latching - 2-Point Locking Rod Kit
Handles - Latching - 2-Point Locking Rod Kit


Kit can be used with any 5/16in. Square shanked handles for two point locking. Kit includes two gold zinc plated steel rods, two plastic rod guides, steel cam, two steel bushings, two wave washers and three set screws.


There is also a good range of Handles - Latching - 2-Point Locking Rod Kit on the Small Parts and Bearings website.


Bumpers - Round - Urethane - Female Washer
Bumpers - Round - Urethane - Female Washer

Also see combined categories:
All Female Bumpers
All Bumpers

With steel core. Washer type has a counterbored hole to accept a socket head cap screw. Flat washer molded inside.


There is also a good range of Bumpers - Round - Urethane - Female Washer on the Small Parts and Bearings website.


Bearings - Thrust - Ball - Flat - Chrome Steel
Bearings - Thrust - Ball - Flat - Chrome Steel

Also see combined categories:
All Ball Thrust Bearings

3 Piece Thrust Bearings Open Type with Flat Washers

These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.

Related Information:

There is also a good range of Bearings - Thrust - Ball - Flat - Chrome Steel on the Small Parts and Bearings website.


Bearings - Thrust - Ball - Flat - Stainless Steel
Bearings - Thrust - Ball - Flat - Stainless Steel

Also see combined categories:
All Ball Thrust Bearings

3 Piece Thrust Bearings Open Type with Flat Washers

These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.

Related Information:

There is also a good range of Bearings - Thrust - Ball - Flat - Stainless Steel on the Small Parts and Bearings website.


Screws - Panel - Jack - Steel
Screws - Panel - Jack - Steel

Also see combined categories:
All Panel Screws

Female 4-40 UNC thread in head allows for secure fixing of studs to a panel.

Each screw comes with two flat washers, 1one lock washer and one hex nut. Yellow chromate zinc finish.

There is also a good range of Screws - Panel - Jack - Steel on the Small Parts and Bearings website.


Chain - Roller - Plastic - Simplex
Chain - Roller - Plastic - Simplex

Also see combined categories:
All Roller Chain

Includes acetal, polyproylene and nylon. Miniature size from 3.1mm up to 12.7mm. Single row.

Snap together construction - no joining links required.

Related Information:

There is also a good range of Chain - Roller - Plastic - Simplex on the Small Parts and Bearings website.


Threaded Rod - Allthread - Plastic
Threaded Rod - Allthread - Plastic

Also see combined categories:
All Threaded Rod

UNC - UNF - METRIC - Nylon and PVC. Also known as booker rod.

Light Weight. Non Corrosive. Vibration Resistant.

There is also a good range of Threaded Rod - Allthread - Plastic on the Small Parts and Bearings website.


Gear Racks - Module 0.5 - Plastic
Gear Racks - Module 0.5 - Plastic

Also see combined categories:
All Metric Gear Racks
All All Gear Racks

20o Pressure Angle. Acetal and Nylon

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.

There is also a good range of Gear Racks - Module 0.5 - Plastic on the Small Parts and Bearings website.


Gear Racks - Module 1.5 - Plastic
Gear Racks - Module 1.5 - Plastic

Also see combined categories:
All Metric Gear Racks
All All Gear Racks

20o Pressure Angle. Acetal and Nylon.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.

There is also a good range of Gear Racks - Module 1.5 - Plastic on the Small Parts and Bearings website.


Gear Racks - Module 1 - Plastic
Gear Racks - Module 1 - Plastic

Also see combined categories:
All Metric Gear Racks
All All Gear Racks

20o Pressure Angle. Acetal and Nylon

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.

There is also a good range of Gear Racks - Module 1 - Plastic on the Small Parts and Bearings website.


Gear Racks - Module 2 - Plastic
Gear Racks - Module 2 - Plastic

Also see combined categories:
All Metric Gear Racks
All All Gear Racks

20o Pressure Angle. Acetal and nylon.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.

There is also a good range of Gear Racks - Module 2 - Plastic on the Small Parts and Bearings website.


Gear Racks - Module 3 - Plastic
Gear Racks - Module 3 - Plastic

Also see combined categories:
All Metric Gear Racks
All All Gear Racks

20o Pressure Angle. Acetal and Nylon

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.

There is also a good range of Gear Racks - Module 3 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 1.5 - Plastic
Gears - Spur - Module 1.5 - Plastic

Also see combined categories:
All Metric Spur Gears
All Spur Gears

PCD = No. of Teeth x 1.500mm. 20o Pressure Angle. Acetal and Nylon

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

There is also a good range of Gears - Spur - Module 1.5 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 2 - Plastic
Gears - Spur - Module 2 - Plastic

Also see combined categories:
All Metric Spur Gears
All Spur Gears

PCD = No. of Teeth x 2.000mm. 20o Pressure Angle. Acetal and nylon

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

There is also a good range of Gears - Spur - Module 2 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 1.5 - Plastic with Insert
Gears - Spur - Module 1.5 - Plastic with Insert

Also see combined categories:
All Metric Spur Gears
All Spur Gears

PCD = No. of Teeth x 1.500mm. 20o Pressure Angle. Acetal and Nylon

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

There is also a good range of Gears - Spur - Module 1.5 - Plastic with Insert on the Small Parts and Bearings website.


Gears - Spur - Module 2 - Plastic with Insert
Gears - Spur - Module 2 - Plastic with Insert

Also see combined categories:
All Metric Spur Gears
All Spur Gears

PCD = No. of Teeth x 2.000mm. 20o Pressure Angle. Acetal and nylon.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

There is also a good range of Gears - Spur - Module 2 - Plastic with Insert on the Small Parts and Bearings website.


Sprockets - 3.12 x 1.47mm - Simplex - Plastic
Sprockets -  3.12 x 1.47mm - Simplex - Plastic

Also see combined categories:
All Sprockets for Roller Chain

Nylon - Acetal - With and without bore inserts.

Match with series 3.12mm miniature plastic chain.

Related Information:

There is also a good range of Sprockets - 3.12 x 1.47mm - Simplex - Plastic on the Small Parts and Bearings website.


Sprockets - 3.75 x 1.6mm - Simplex - Plastic
Sprockets -  3.75 x 1.6mm - Simplex - Plastic

Also see combined categories:
All Sprockets for Roller Chain

Nylon - Acetal - With and without bore inserts.

Match with series 3.75mm miniature plastic or stainless chain.

Related Information:

There is also a good range of Sprockets - 3.75 x 1.6mm - Simplex - Plastic on the Small Parts and Bearings website.


Sprockets - 6.35 x 2.8mm - Simplex - Plastic
Sprockets -  6.35 x 2.8mm - Simplex - Plastic

Also see combined categories:
All Sprockets for Roller Chain

Nylon - Acetal - With and without bore inserts.

Match with series 6.35mm plastic or steel chain (25-1 ASA). American Standard 25-1 - 1/4 inch.

Related Information:

There is also a good range of Sprockets - 6.35 x 2.8mm - Simplex - Plastic on the Small Parts and Bearings website.


Sprockets - 9.53 x 4.7mm - Simplex - Plastic
Sprockets -  9.53 x 4.7mm - Simplex - Plastic

Also see combined categories:
All Sprockets for Roller Chain

Nylon - Acetal - With and without bore inserts.

Match with series 9.53x4.7mm plastic or steel chain (35-1 ASA). American Standard 35-1 - 3/8 inch.

Related Information:

There is also a good range of Sprockets - 9.53 x 4.7mm - Simplex - Plastic on the Small Parts and Bearings website.


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 122230 products in 2651 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 122230 products in 2651 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.