Miniature Bearings Australia Pty Ltd

Washers Flat Fibre Categories


Washers - Flat - Fibre
Washers - Flat - Fibre

Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic

Flat red vulcanised fibre washers. Black available on request and sufficient quantity.

Operating temperature up to 105 oC. Tensile strength 6 kg/mm2. Elongation up to 19 percent. Shrinkage up to 3 percent thickness. Water absorption 4 to 70 percent after 24 hours. Density 1 to 1.45 g/cm.

Related Information:

There is also a good range of Washers - Flat - Fibre on the Small Parts and Bearings website.


You may also be interested in

Washers Flat Metallic


Washers - Flat - Aluminium - Precision Shim
Washers - Flat - Aluminium - Precision Shim

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers.

This category may be available in the new MBA online store at Washers - Flat - Aluminium - Precision Shim.

Related Information:

There is also a good range of Washers - Flat - Aluminium - Precision Shim on the Small Parts and Bearings website.


Washers - Flat - Brass - Commercial
Washers - Flat - Brass - Commercial

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers.

Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD. This category may be available in the new MBA online store at Washers - Flat - Brass - Commercial.

Related Information:

There is also a good range of Washers - Flat - Brass - Commercial on the Small Parts and Bearings website.


Washers - Flat - Brass - Precision Shim
Washers - Flat - Brass - Precision Shim

Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Precision Tolerances. Standard and laminated brass shim washers.

This category may be available in the new MBA online store at Washers - Flat - Brass - Precision Shim.

Related Information:

There is also a good range of Washers - Flat - Brass - Precision Shim on the Small Parts and Bearings website.


Washers - Flat - Carbon Spring Steel - Precision Shim
Washers - Flat - Carbon Spring Steel - Precision Shim

Also see combined categories:
All Precision Shim Washers
All Flat Washers and Spacers - Metallic

Flat Carbon Spring Steel Washers. Commonly used for fast and accurate spacing of milling cutters, gang cutters, saws, slitting blades and grinding tools.

C1010 steel types best suited to arbor shimming. This category may be available in the new MBA online store at Washers - Flat - Carbon Spring Steel - Precision Shim.

Related Information:

There is also a good range of Washers - Flat - Carbon Spring Steel - Precision Shim on the Small Parts and Bearings website.


Washers - Flat - Copper - Precision Shim
Washers - Flat - Copper - Precision Shim

Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Precision Tolerances.

This category may be available in the new MBA online store at Washers - Flat - Copper - Precision Shim.

Related Information:

There is also a good range of Washers - Flat - Copper - Precision Shim on the Small Parts and Bearings website.


Washers - Flat - Hardened Steel
Washers - Flat - Hardened Steel

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Medium carbon steel through hardened to RC 43-49. Zinc dichromate finish. All dimensions shows are minimum.

This category may be available in the new MBA online store at Washers - Flat - Hardened Steel.

Related Information:

There is also a good range of Washers - Flat - Hardened Steel on the Small Parts and Bearings website.


Washers - Flat - High Tensile
Washers - Flat - High Tensile

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Grade 8 high tensile washers

ASTM F436 1985. Please note! Tolerances for commercial grade washers are much larger than for precision washers. This category may be available in the new MBA online store at Washers - Flat - High Tensile.

Related Information:

There is also a good range of Washers - Flat - High Tensile on the Small Parts and Bearings website.


Washers - Flat - Mild Steel
Washers - Flat - Mild Steel

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers. Includes fender washers. Zinc plated and unplated listings.

In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD. This category may be available in the new MBA online store at Washers - Flat - Mild Steel.

Related Information:

There is also a good range of Washers - Flat - Mild Steel on the Small Parts and Bearings website.


Washers - Flat - Sintered Bronze - Precision
Washers - Flat - Sintered Bronze - Precision

Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat thrust washers made from oil impregnated sintered bronze

This category may be available in the new MBA online store at Washers - Flat - Sintered Bronze - Precision.

Related Information:

There is also a good range of Washers - Flat - Sintered Bronze - Precision on the Small Parts and Bearings website.


Washers - Flat - Stainless Steel 304 - Commercial
Washers - Flat - Stainless Steel 304 - Commercial

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers.

Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers. This category may be available in the new MBA online store at Washers - Flat - Stainless Steel 304 - Commercial.

Related Information:

There is also a good range of Washers - Flat - Stainless Steel 304 - Commercial on the Small Parts and Bearings website.


Washers - Flat - Stainless Steel 316 - Commercial
Washers - Flat - Stainless Steel 316 - Commercial

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers.

Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers. This category may be available in the new MBA online store at Washers - Flat - Stainless Steel 316 - Commercial.

Related Information:

There is also a good range of Washers - Flat - Stainless Steel 316 - Commercial on the Small Parts and Bearings website.


Washers - Flat - Stainless Steel - Precision Shim
Washers - Flat - Stainless Steel - Precision Shim

Also see combined categories:
All Precision Shim Washers
All Flat Washers and Spacers - Metallic

Precision Tolerances.

This category may be available in the new MBA online store at Washers - Flat - Stainless Steel - Precision Shim.

Related Information:

There is also a good range of Washers - Flat - Stainless Steel - Precision Shim on the Small Parts and Bearings website.


Washers - Flat - Stamped - Heavy Duty - Hardened
Washers - Flat - Stamped - Heavy Duty - Hardened

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Heat treated. Black oxide finish.

This category may be available in the new MBA online store at Washers - Flat - Stamped - Heavy Duty - Hardened.

Related Information:

There is also a good range of Washers - Flat - Stamped - Heavy Duty - Hardened on the Small Parts and Bearings website.


Washers - Flat - Titanium - CP Grade 1
Washers - Flat - Titanium - CP Grade 1

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.

Commercially pure for general industrial corrosion applications. UNS R50250. Please note! Tolerances for commercial grade washers are much larger than for precision washers. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance. This category may be available in the new MBA online store at Washers - Flat - Titanium - CP Grade 1.

Related Information:

There is also a good range of Washers - Flat - Titanium - CP Grade 1 on the Small Parts and Bearings website.


Washers Flat Plastic


Washers - Flat - Nylon
Washers - Flat - Nylon

Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic

Flat washers.

Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD. This category may be available in the new MBA online store at Washers - Flat - Nylon.

Related Information:

There is also a good range of Washers - Flat - Nylon on the Small Parts and Bearings website.


Washers - Flat - PTFE - Precision Shim
Washers - Flat - PTFE - Precision Shim

Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic

Teflon Washers

This category may be available in the new MBA online store at Washers - Flat - PTFE - Precision Shim.

Related Information:

There is also a good range of Washers - Flat - PTFE - Precision Shim on the Small Parts and Bearings website.


Washers - Flat - PVC
Washers - Flat - PVC

Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic

Flat washers.

This category may be available in the new MBA online store at Washers - Flat - PVC.

Related Information:

There is also a good range of Washers - Flat - PVC on the Small Parts and Bearings website.


Washers Flat Rubber


Washers - Flat - Rubber
Washers - Flat - Rubber

Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic

Nitrile Duro 70

This category may be available in the new MBA online store at Washers - Flat - Rubber.

Related Information:

There is also a good range of Washers - Flat - Rubber on the Small Parts and Bearings website.


Washers Flat Metallic


Washers - C - Steel
Washers - C - Steel

Also see combined categories:
All C Washers

Cold finished steel, case hardened with a black oxide finish.

This category may be available in the new MBA online store at Washers - C - Steel.

There is also a good range of Washers - C - Steel on the Small Parts and Bearings website.


Washers - C - Swing
Washers - C - Swing


Cold finished steel, hardened and ground. Black oxide finish.

This category may be available in the new MBA online store at Washers - C - Swing.

There is also a good range of Washers - C - Swing on the Small Parts and Bearings website.


Washers - Heavy Duty - Machined - Steel
Washers - Heavy Duty - Machined - Steel

Also see combined categories:
All Flat Washers and Spacers - Metallic

Case hardened cold finished steel with black oxide finish.

This category may be available in the new MBA online store at Washers - Heavy Duty - Machined - Steel.

Related Information:

There is also a good range of Washers - Heavy Duty - Machined - Steel on the Small Parts and Bearings website.


Washers - Heavy Duty - Machined - Stainless Steel
Washers - Heavy Duty - Machined - Stainless Steel

Also see combined categories:
All Flat Washers and Spacers - Metallic

303 Stainless Steel

This category may be available in the new MBA online store at Washers - Heavy Duty - Machined - Stainless Steel.

Related Information:

There is also a good range of Washers - Heavy Duty - Machined - Stainless Steel on the Small Parts and Bearings website.


Screws Thumb


Screws - Thumb - Flat Key Head - Washer Face - Steel
Screws - Thumb - Flat Key Head - Washer Face - Steel

Also see combined categories:
All Thumb Screws

Flat Key head malleable iron screws with an integral washer

This category may be available in the new MBA online store at Screws - Thumb - Flat Key Head - Washer Face - Steel.

Related Information:

There is also a good range of Screws - Thumb - Flat Key Head - Washer Face - Steel on the Small Parts and Bearings website.


Spacers


Spacers - Arbor
Spacers - Arbor


Flat arbor shim washers with keyway groove.

This category may be available in the new MBA online store at Spacers - Arbor.

There is also a good range of Spacers - Arbor on the Small Parts and Bearings website.


Washers - Disc Spring - Plastic
Washers - Disc Spring - Plastic

Also see combined categories:
All Disc Springs

Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb(R) material.

There is also a good range of Washers - Disc Spring - Plastic on the Small Parts and Bearings website.


Bearings - Thrust - Ball - Flat - Chrome Steel
Bearings - Thrust - Ball - Flat - Chrome Steel

Also see combined categories:
All Ball Thrust Bearings

3 Piece Thrust Bearings Open Type with Flat Washers

These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at Bearings - Thrust - Ball - Flat - Chrome Steel.

Related Information:

There is also a good range of Bearings - Thrust - Ball - Flat - Chrome Steel on the Small Parts and Bearings website.


Bearings - Thrust - Ball - Flat - Stainless Steel
Bearings - Thrust - Ball - Flat - Stainless Steel

Also see combined categories:
All Ball Thrust Bearings

3 Piece Thrust Bearings Open Type with Flat Washers

These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at Bearings - Thrust - Ball - Flat - Stainless Steel.

Related Information:

There is also a good range of Bearings - Thrust - Ball - Flat - Stainless Steel on the Small Parts and Bearings website.


Washers - Self Aligning - Components - Hardened Steel
Washers - Self Aligning - Components - Hardened Steel

Also see combined categories:
All Thrust Washers
All Aligning Washers

Spherical Seat Washers. Washer A (aligning) and washer B (seat) sold separately.

Case Hardened steel 9 S Mn Pb 28 K DIN 6319. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-G washers are used for clamping mechanical parts with non-parallel surfaces. Designed for screw solidity in compliance with 8.8. Limited for use on flat closed ring areas - not for elongated holes.

There is also a good range of Washers - Self Aligning - Components - Hardened Steel on the Small Parts and Bearings website.


Pins - Hammer Drive - Flat Head
Pins - Hammer Drive - Flat Head

Also see combined categories:
All Hammer Drive Pins

Used to replace screws where the need to remove the pin is unlikely.

Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.

Related Information:

There is also a good range of Pins - Hammer Drive - Flat Head on the Small Parts and Bearings website.


Washers - Thrust - DP4 Type
Washers - Thrust - DP4 Type

Also see combined categories:
All Thrust Washers

Wear resistant helping to prevent wear deposits in the lubricating oil after long working periods. Designed for use in oil pumps and dampers.

Operating Temperature -200o to 280o Celsius. Maximum load 250N per mm2. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free. This category may be available in the new MBA online store at Washers - Thrust - DP4 Type.

There is also a good range of Washers - Thrust - DP4 Type on the Small Parts and Bearings website.


Washers - Disc Spring - Ball Bearing Type
Washers - Disc Spring - Ball Bearing Type

Also see combined categories:
All Disc Springs

Specially designed for preloading the outer ring of ball bearings. C1075 steel. Includes disc springs to DIN 2093.

Ensures perfect bearing positioning with no sideways play. May be used to provide bearing preload. Load tolerance +/- 20% of load shown. This category may be available in the new MBA online store at Washers - Disc Spring - Ball Bearing Type.

There is also a good range of Washers - Disc Spring - Ball Bearing Type on the Small Parts and Bearings website.


Washers - Disc Spring - Carbon Steel
Washers - Disc Spring - Carbon Steel

Also see combined categories:
All Disc Springs

Includes disc springs to DIN 2093.

Manufactured under strict quality control to conform to DIN 2093. This category may be available in the new MBA online store at Washers - Disc Spring - Carbon Steel.

There is also a good range of Washers - Disc Spring - Carbon Steel on the Small Parts and Bearings website.


Washers - Disc Spring - Flange Locking Type
Washers - Disc Spring - Flange Locking Type

Also see combined categories:
All Disc Springs

Used under the nuts or bolt head in bolted flange joints that are subject to thermal or mechanical shock.

The discs deflect and move with the bolted joint. Helps to compensate for loosening that may develop preventing damage and leaks caused by thermal expansion, contraction and shock. Made from 17.7 PH Stainless Steel. Temperature range minus 220 to +300o Celsius. Load tolerance +/- 20% of load shown.

There is also a good range of Washers - Disc Spring - Flange Locking Type on the Small Parts and Bearings website.


Washers - Disc Spring - Stainless Steel
Washers - Disc Spring - Stainless Steel

Also see combined categories:
All Disc Springs

Includes disc springs to DIN 2093 and belleville washers to DIN 6796.

Manufactured under strict quality control to conform to DIN 2093. This category may be available in the new MBA online store at Washers - Disc Spring - Stainless Steel.

There is also a good range of Washers - Disc Spring - Stainless Steel on the Small Parts and Bearings website.


Washers - Spring - 2 Wave Type - Zinc Plated
Washers - Spring - 2 Wave Type - Zinc Plated

Also see combined categories:
All Wave Washers

Wave Washers - All Materials.

This category may be available in the new MBA online store at Washers - Spring - 2 Wave Type - Zinc Plated.

There is also a good range of Washers - Spring - 2 Wave Type - Zinc Plated on the Small Parts and Bearings website.


Washers - Spring - 3 Wave Type - 302 Stainless Steel
Washers - Spring - 3 Wave Type - 302 Stainless Steel

Also see combined categories:
All Wave Washers

Wave Washers - also called crinkle wave.

This category may be available in the new MBA online store at Washers - Spring - 3 Wave Type - 302 Stainless Steel.

There is also a good range of Washers - Spring - 3 Wave Type - 302 Stainless Steel on the Small Parts and Bearings website.


Washers - Spring - 3 Wave Type - 400 Grade Stainless
Washers - Spring - 3 Wave Type - 400 Grade Stainless

Also see combined categories:
All Wave Washers

Wave Washers - also called crinkle wave.

This category may be available in the new MBA online store at Washers - Spring - 3 Wave Type - 400 Grade Stainless.

There is also a good range of Washers - Spring - 3 Wave Type - 400 Grade Stainless on the Small Parts and Bearings website.


Washers - Spring - 3 Wave Type - Berryllium Copper
Washers - Spring - 3 Wave Type - Berryllium Copper

Also see combined categories:
All Wave Washers

Wave Washers - also called crinkle wave.

This category may be available in the new MBA online store at Washers - Spring - 3 Wave Type - Berryllium Copper.

There is also a good range of Washers - Spring - 3 Wave Type - Berryllium Copper on the Small Parts and Bearings website.


Washers - Spring - Curved - Carbon Steel
Washers - Spring - Curved - Carbon Steel

Also see combined categories:
All Wave Washers

Wave Washers - All Materials.

ID and OD are long axis dimensions. This category may be available in the new MBA online store at Washers - Spring - Curved - Carbon Steel.

There is also a good range of Washers - Spring - Curved - Carbon Steel on the Small Parts and Bearings website.


Washers - Spring - Curved - Stainless Steel
Washers - Spring - Curved - Stainless Steel

Also see combined categories:
All Wave Washers

Wave Washers - All Materials.

ID and OD are long axis dimensions. This category may be available in the new MBA online store at Washers - Spring - Curved - Stainless Steel.

There is also a good range of Washers - Spring - Curved - Stainless Steel on the Small Parts and Bearings website.


Washers - Spring - Wave Type - Carbon Steel
Washers - Spring - Wave Type - Carbon Steel

Also see combined categories:
All Wave Washers

Wave Washers - also called crinkle wave. Includes 2 and 3 wave types. This category includes EPL type bearing pre-load washers.

This category may be available in the new MBA online store at Washers - Spring - Wave Type - Carbon Steel.

There is also a good range of Washers - Spring - Wave Type - Carbon Steel on the Small Parts and Bearings website.


Washers - Self Aligning - Components - Stainless Steel
Washers - Self Aligning - Components - Stainless Steel

Also see combined categories:
All Thrust Washers
All Aligning Washers

Spherical Seat Washers. Washer A (aligning) and washer B (seat) sold separately.

AISI 303 Stainless Steel. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces. This category may be available in the new MBA online store at Washers - Self Aligning - Components - Stainless Steel.

There is also a good range of Washers - Self Aligning - Components - Stainless Steel on the Small Parts and Bearings website.


Washers - Self Aligning - Sets - Hardened Steel
Washers - Self Aligning - Sets - Hardened Steel

Also see combined categories:
All Thrust Washers
All Aligning Washers

Spherical Seat Washers

Hardened steel 9 S Mn Pb 28 K DIN 6319. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces. This category may be available in the new MBA online store at Washers - Self Aligning - Sets - Hardened Steel.

There is also a good range of Washers - Self Aligning - Sets - Hardened Steel on the Small Parts and Bearings website.


Washers - Self Aligning - Sets - Stainless Steel
Washers - Self Aligning - Sets - Stainless Steel

Also see combined categories:
All Thrust Washers
All Aligning Washers

Spherical Seat Washers

AISI 303 Stainless Steel. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces. This category may be available in the new MBA online store at Washers - Self Aligning - Sets - Stainless Steel.

There is also a good range of Washers - Self Aligning - Sets - Stainless Steel on the Small Parts and Bearings website.


Washers - Cup - Aluminium
Washers - Cup - Aluminium

Also see combined categories:
All Cup Washers

For countersunk screws.

Aluminium solid cup washers. This category may be available in the new MBA online store at Washers - Cup - Aluminium.

There is also a good range of Washers - Cup - Aluminium on the Small Parts and Bearings website.


Washers - Cup - Brass - Nickel Plated
Washers - Cup - Brass - Nickel Plated

Also see combined categories:
All Cup Washers

For countersunk screws.

This category may be available in the new MBA online store at Washers - Cup - Brass - Nickel Plated.

There is also a good range of Washers - Cup - Brass - Nickel Plated on the Small Parts and Bearings website.


Washers - Cup - Nylon
Washers - Cup - Nylon

Also see combined categories:
All Cup Washers

Countersunk washers for use with screws for decorative finishing

This category may be available in the new MBA online store at Washers - Cup - Nylon.

There is also a good range of Washers - Cup - Nylon on the Small Parts and Bearings website.


Washers - Cup - Stainless Steel
Washers - Cup - Stainless Steel

Also see combined categories:
All Cup Washers

For countersunk screws.

Stainless Steel cup washers. This category may be available in the new MBA online store at Washers - Cup - Stainless Steel.

There is also a good range of Washers - Cup - Stainless Steel on the Small Parts and Bearings website.


Washers - Lock - External Tooth - Spring Steel
Washers - Lock - External Tooth - Spring Steel

Also see combined categories:
All External Tooth Lock Washers
All Lock Washers

Dimensions are nominal and may vary between batches. This category may be available in the new MBA online store at Washers - Lock - External Tooth - Spring Steel.

There is also a good range of Washers - Lock - External Tooth - Spring Steel on the Small Parts and Bearings website.





Main Pages

5 Axis Machine Tool Bearings About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Charity Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Distributor Locations Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Satellite Reaction Wheels Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 209769 products in 2107 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 209769 products in 2107 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.