Miniature Bearings Australia Pty Ltd

Vee Belts Categories


Belts - Wedge - 12.7 x 10.0mm - SPA
Belts - Wedge - 12.7 x 10.0mm - SPA

Also see combined categories:
All Vee Belts 12.5mm and 12.7mm Top Width

12.7mm Top Width x 10.0mm Height.

Sizes are nominal and may vary slightly. This category may be available in the new MBA online store at Belts - Wedge - 12.7 x 10.0mm - SPA.

Related Information:

There is also a good range of Belts - Wedge - 12.7 x 10.0mm - SPA on the Small Parts and Bearings website.


Belts - Wedge - 15.9 x 13.5mm - Notched 5VX
Belts - Wedge - 15.9 x 13.5mm - Notched 5VX

Also see combined categories:
All Vee Belts 15.9mm and 16.5mm Top Width

15.9mm Top Width x 13.5mm Height.

This category may be available in the new MBA online store at Belts - Wedge - 15.9 x 13.5mm - Notched 5VX.

Related Information:

There is also a good range of Belts - Wedge - 15.9 x 13.5mm - Notched 5VX on the Small Parts and Bearings website.


Belts - Wedge - 16.3 x 13.0mm - SPB - 5V
Belts - Wedge - 16.3 x 13.0mm - SPB - 5V

Also see combined categories:
All Vee Belts 15.9mm and 16.5mm Top Width

16.3mm Top Width x 13.0mm Height.

Sizes are nominal and may vary slightly. This category may be available in the new MBA online store at Belts - Wedge - 16.3 x 13.0mm - SPB - 5V.

Related Information:

There is also a good range of Belts - Wedge - 16.3 x 13.0mm - SPB - 5V on the Small Parts and Bearings website.


Belts - Wedge - 25.4 x 22.2mm - SPP-8V
Belts - Wedge - 25.4 x 22.2mm - SPP-8V


25.4mm Top Width x 22.2mm Height.

Sizes are nominal and may vary slightly. This category may be available in the new MBA online store at Belts - Wedge - 25.4 x 22.2mm - SPP-8V.

Related Information:

There is also a good range of Belts - Wedge - 25.4 x 22.2mm - SPP-8V on the Small Parts and Bearings website.


Belts - Wedge - 9.7 x 8.0mm - SPZ - 3V
Belts - Wedge - 9.7 x 8.0mm - SPZ - 3V

Also see combined categories:
All Vee Pulleys M Section 10mm Top Width

Miniature and small belts. 9.7mm Top Width x 8.0mm Height.

Sizes are nominal and may vary slightly. This category may be available in the new MBA online store at Belts - Wedge - 9.7 x 8.0mm - SPZ - 3V.

Related Information:

There is also a good range of Belts - Wedge - 9.7 x 8.0mm - SPZ - 3V on the Small Parts and Bearings website.


Belts - Wedge - 9.5 x 7.9mm - Notched XPZ - 3VX
Belts - Wedge - 9.5 x 7.9mm - Notched XPZ - 3VX

Also see combined categories:
All Vee Pulleys M Section 10mm Top Width

Miniature and small belts. 9.5mm Top Width x 7.9mm Height.

This category may be available in the new MBA online store at Belts - Wedge - 9.5 x 7.9mm - Notched XPZ - 3VX.

Related Information:

There is also a good range of Belts - Wedge - 9.5 x 7.9mm - Notched XPZ - 3VX on the Small Parts and Bearings website.


Belts - Vee - 10.0 x 5.5mm - M-3L
Belts - Vee - 10.0 x 5.5mm - M-3L

Also see combined categories:
All Vee Belts 8mm and 10mm Top Width

Miniature and small belts. 10.0mm Top Width x 5.5mm Height.

Sizes are nominal and may vary slightly. Items marked as Fractional Horsepower are designed for general purrpose low horseposer applications such as laundry machines, home workshop tools, small fans and blowers, garage equipment, small metal and woodworking tools etc. Belts shown as Fractional Horsepower type should not be used with reverse side idlers.

Related Information:

There is also a good range of Belts - Vee - 10.0 x 5.5mm - M-3L on the Small Parts and Bearings website.


Belts - Vee - 12.5 x 9.0mm - A-4L
Belts - Vee - 12.5 x 9.0mm - A-4L

Also see combined categories:
All Vee Belts 12.5mm and 12.7mm Top Width

12.5mm Top Width x 9.0mm Height.

Sizes are nominal and may vary slightly. Items marked as Fractional Horsepower are designed for general purrpose low horseposer applications such as laundry machines, home workshop tools, small fans and blowers, garage equipment, small metal and woodworking tools etc. Belts shown as Fractional Horsepower type should not be used with reverse side idlers.

Related Information:

There is also a good range of Belts - Vee - 12.5 x 9.0mm - A-4L on the Small Parts and Bearings website.


Belts - Vee - 12.7 x 7.9mm - Notched AX
Belts - Vee - 12.7 x 7.9mm - Notched AX

Also see combined categories:
All Vee Belts 12.5mm and 12.7mm Top Width

12.7mm Top Width x 7.9mm Height.

This category may be available in the new MBA online store at Belts - Vee - 12.7 x 7.9mm - Notched AX.

Related Information:

There is also a good range of Belts - Vee - 12.7 x 7.9mm - Notched AX on the Small Parts and Bearings website.


Belts - Vee - 15.9 x 10.3mm - Notched BX
Belts - Vee - 15.9 x 10.3mm - Notched BX

Also see combined categories:
All Vee Belts 15.9mm and 16.5mm Top Width

15.9mm Top Width x 10.3mm Height.

This category may be available in the new MBA online store at Belts - Vee - 15.9 x 10.3mm - Notched BX.

Related Information:

There is also a good range of Belts - Vee - 15.9 x 10.3mm - Notched BX on the Small Parts and Bearings website.


Belts - Vee - 22.2 x 13.5mm - Notched CX
Belts - Vee - 22.2 x 13.5mm - Notched CX

Also see combined categories:
All Vee Belts 22mm and 22.2mm Top Width

22.2mm Top Width x 13.5mm Height.

This category may be available in the new MBA online store at Belts - Vee - 22.2 x 13.5mm - Notched CX.

Related Information:

There is also a good range of Belts - Vee - 22.2 x 13.5mm - Notched CX on the Small Parts and Bearings website.


Belts - Vee - 8.0 x 4.0mm
Belts - Vee - 8.0 x 4.0mm

Also see combined categories:
All Vee Belts 8mm and 10mm Top Width

Miniature and small belts. 8.0mm Top Width x 4.0mm Height.

Sizes are nominal and may vary slightly. This category may be available in the new MBA online store at Belts - Vee - 8.0 x 4.0mm.

Related Information:

There is also a good range of Belts - Vee - 8.0 x 4.0mm on the Small Parts and Bearings website.


Belts - Vee - 16.5 x 11.0mm - B
Belts - Vee - 16.5 x 11.0mm - B

Also see combined categories:
All Vee Belts 15.9mm and 16.5mm Top Width

16.5mm Top Width x 11.0mm Height.

Sizes are nominal and may vary slightly. This category may be available in the new MBA online store at Belts - Vee - 16.5 x 11.0mm - B.

Related Information:

There is also a good range of Belts - Vee - 16.5 x 11.0mm - B on the Small Parts and Bearings website.


Belts - Vee - 31.5 x 19.0mm - D
Belts - Vee - 31.5 x 19.0mm - D


31.5mm Top Width x 19.0mm Height.

Sizes are nominal and may vary slightly. This category may be available in the new MBA online store at Belts - Vee - 31.5 x 19.0mm - D.

Related Information:

There is also a good range of Belts - Vee - 31.5 x 19.0mm - D on the Small Parts and Bearings website.


You may also be interested in

Belts Poly Vee


Belts - Poly V - J Section
Belts - Poly V - J Section


Belts include a tensile cord, most suited for industrial or adjustable applications

Poly Vee are ideal for high ratio and high speed drives. J Section polyvee is 2.34mm pitch and 3.56mm belt height. Note, this series is not a strechable type of belt. The belt width wll be determined by the number of ribs x the pitch. This category may be available in the new MBA online store at Belts - Poly V - J Section.

Related Information:

There is also a good range of Belts - Poly V - J Section on the Small Parts and Bearings website.


Pulleys Vee


Pulleys - Vee - A - 4L - Single Row - Through Bore - Cast Iron
Pulleys - Vee - A - 4L - Single Row - Through Bore - Cast Iron

Also see combined categories:
All Vee Pulleys A Section 12.5 and 12.7mm Top Width

Dual purpose pulleys suit A section and M section belts

To determine the pitch diameter for M section deduct 8.636mm (0.34 inch) from the pitch diameter listed. This category may be available in the new MBA online store at Pulleys - Vee - A - 4L - Single Row - Through Bore - Cast Iron.

Related Information:

There is also a good range of Pulleys - Vee - A - 4L - Single Row - Through Bore - Cast Iron on the Small Parts and Bearings website.


Pulleys - Poly V - J Section - Through Bored
Pulleys - Poly V - J Section - Through Bored


Poly V drives are ideal for high ratio drives and high speed. J Section is 2.34mm pitch and 3.56mm belt height. This category may be available in the new MBA online store at Pulleys - Poly V - J Section - Through Bored.

Related Information:

There is also a good range of Pulleys - Poly V - J Section - Through Bored on the Small Parts and Bearings website.


Pulleys - Poly V - J Section - QD Bush
Pulleys - Poly V - J Section - QD Bush


Use with QD bush to suit your bore requirement

Poly V drives are ideal for high ratio drives and high speed. J Section is 2.34mm pitch and 3.56mm belt height. This category may be available in the new MBA online store at Pulleys - Poly V - J Section - QD Bush.

Related Information:

There is also a good range of Pulleys - Poly V - J Section - QD Bush on the Small Parts and Bearings website.


Belts - Posi-Drive - 4.00 mm Circular Pitch - Single Core
Belts - Posi-Drive - 4.00 mm Circular Pitch - Single Core

Also see combined categories:
All Posi-Drive Belts

Same as US 20 Pitch - Use with Posi-Drive Pulleys.

Use Single Core with Posi-Drive Pulleys. 3.990mm Circular Pitch. Same as US 20 Pitch. Posi-drive material lengths in this category can not be joined by the customer as special equipment is required. Material lengths are used in reciprocating applications and not meant to be joined. This category may be available in the new MBA online store at Belts - Posi-Drive - 4.00 mm Circular Pitch - Single Core.

Related Information:

There is also a good range of Belts - Posi-Drive - 4.00 mm Circular Pitch - Single Core on the Small Parts and Bearings website.


Belts - Round - Urethane - Seamless
Belts - Round - Urethane - Seamless


Seamless round belting. Yellow colour. Temperature range -31 to 70 Deg C (-25 to 158 Deg F).

Working Load is 8 Percent of Tensile Strength. Use with grooved idler pulleys with diameters at least 8 times the belt width. This category may be available in the new MBA online store at Belts - Round - Urethane - Seamless.

Related Information:

There is also a good range of Belts - Round - Urethane - Seamless on the Small Parts and Bearings website.


Belts - Inch Timing - 2.073mm Pitch 40DP - 3.2mm Wide
Belts - Inch Timing - 2.073mm Pitch 40DP - 3.2mm Wide

Also see combined categories:
All 40DP 2.073mm Pitch Timing Belts

Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Pitch (P) - 2.073mm (0.0816 inch).

Related Information:

There is also a good range of Belts - Inch Timing - 2.073mm Pitch 40DP - 3.2mm Wide on the Small Parts and Bearings website.


Belts - Inch Timing - 2.073mm Pitch 40DP - 4.8mm Wide
Belts - Inch Timing - 2.073mm Pitch 40DP - 4.8mm Wide

Also see combined categories:
All 40DP 2.073mm Pitch Timing Belts

Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Pitch (P) - 2.073mm (0.0816 inch).

Related Information:

There is also a good range of Belts - Inch Timing - 2.073mm Pitch 40DP - 4.8mm Wide on the Small Parts and Bearings website.


Belts - Inch Timing - 2.073mm Pitch 40DP - 6.4mm Wide
Belts - Inch Timing - 2.073mm Pitch 40DP - 6.4mm Wide

Also see combined categories:
All 40DP 2.073mm Pitch Timing Belts

Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Pitch (P) - 2.073mm (0.0816 inch).

Related Information:

There is also a good range of Belts - Inch Timing - 2.073mm Pitch 40DP - 6.4mm Wide on the Small Parts and Bearings website.


Belts - Inch Timing - 2.073mm Pitch 40DP - 7.9mm Wide
Belts - Inch Timing - 2.073mm Pitch 40DP - 7.9mm Wide

Also see combined categories:
All 40DP 2.073mm Pitch Timing Belts

Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Pitch (P) - 2.073mm (0.0816 inch).

Related Information:

There is also a good range of Belts - Inch Timing - 2.073mm Pitch 40DP - 7.9mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 10.000mm Pitch - AT10 - 10mm Wide
Belts - Metric Timing - 10.000mm Pitch - AT10 - 10mm Wide

Also see combined categories:
All 10mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 10.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 10.000mm Pitch - AT10 - 10mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 10.000mm Pitch - AT10 - 12mm Wide
Belts - Metric Timing - 10.000mm Pitch - AT10 - 12mm Wide

Also see combined categories:
All 10mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 10.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 10.000mm Pitch - AT10 - 12mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 10.000mm Pitch - AT10 - 16mm Wide
Belts - Metric Timing - 10.000mm Pitch - AT10 - 16mm Wide

Also see combined categories:
All 10mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 10.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 10.000mm Pitch - AT10 - 16mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 10.000mm Pitch - AT10 - 20mm Wide
Belts - Metric Timing - 10.000mm Pitch - AT10 - 20mm Wide

Also see combined categories:
All 10mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 10.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 10.000mm Pitch - AT10 - 20mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 10.000mm Pitch - AT10 - 25mm Wide
Belts - Metric Timing - 10.000mm Pitch - AT10 - 25mm Wide

Also see combined categories:
All 10mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 10.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 10.000mm Pitch - AT10 - 25mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 10.000mm Pitch - AT10 - 32mm Wide
Belts - Metric Timing - 10.000mm Pitch - AT10 - 32mm Wide

Also see combined categories:
All 10mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 10.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 10.000mm Pitch - AT10 - 32mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 10.000mm Pitch - AT10 - 50mm Wide
Belts - Metric Timing - 10.000mm Pitch - AT10 - 50mm Wide

Also see combined categories:
All 10mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 10.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 10.000mm Pitch - AT10 - 50mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 5.000mm Pitch AT5 - 10mm Wide
Belts - Metric Timing - 5.000mm Pitch AT5 - 10mm Wide

Also see combined categories:
All 5mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 5.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 5.000mm Pitch AT5 - 10mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 5.000mm Pitch AT5 - 12mm Wide
Belts - Metric Timing - 5.000mm Pitch AT5 - 12mm Wide

Also see combined categories:
All 5mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 5.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 5.000mm Pitch AT5 - 12mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 5.000mm Pitch AT5 - 16mm Wide
Belts - Metric Timing - 5.000mm Pitch AT5 - 16mm Wide

Also see combined categories:
All 5mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 5.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 5.000mm Pitch AT5 - 16mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 5.000mm Pitch AT5 - 20mm Wide
Belts - Metric Timing - 5.000mm Pitch AT5 - 20mm Wide

Also see combined categories:
All 5mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 5.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 5.000mm Pitch AT5 - 20mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 5.000mm Pitch AT5 - 25mm Wide
Belts - Metric Timing - 5.000mm Pitch AT5 - 25mm Wide

Also see combined categories:
All 5mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 5.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 5.000mm Pitch AT5 - 25mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 5.000mm Pitch AT5 - 6mm Wide
Belts - Metric Timing - 5.000mm Pitch AT5 - 6mm Wide

Also see combined categories:
All 5mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 5.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 5.000mm Pitch AT5 - 6mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 5.000mm Pitch AT5 - 8mm Wide
Belts - Metric Timing - 5.000mm Pitch AT5 - 8mm Wide

Also see combined categories:
All 5mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 5.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 5.000mm Pitch AT5 - 8mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 14.000mm Pitch GT - 115mm Wide
Belts - Metric Timing - 14.000mm Pitch GT - 115mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 14.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 14.000mm Pitch GT - 115mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 14.000mm Pitch GT - 170mm Wide
Belts - Metric Timing - 14.000mm Pitch GT - 170mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 14.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 14.000mm Pitch GT - 170mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 14.000mm Pitch GT - 40mm Wide
Belts - Metric Timing - 14.000mm Pitch GT - 40mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 14.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 14.000mm Pitch GT - 40mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 14.000mm Pitch GT - 55mm Wide
Belts - Metric Timing - 14.000mm Pitch GT - 55mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 14.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 14.000mm Pitch GT - 55mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 14.000mm Pitch GT - 85mm Wide
Belts - Metric Timing - 14.000mm Pitch GT - 85mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 14.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 14.000mm Pitch GT - 85mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 2.000mm Pitch GT - 3mm Wide
Belts - Metric Timing - 2.000mm Pitch GT - 3mm Wide

Also see combined categories:
All 2mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 2.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 2.000mm Pitch GT - 3mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 2.000mm Pitch GT - 4mm Wide
Belts - Metric Timing - 2.000mm Pitch GT - 4mm Wide

Also see combined categories:
All 2mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts.

Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 2.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 2.000mm Pitch GT - 4mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 2.000mm Pitch GT - 6mm Wide - Clean
Belts - Metric Timing - 2.000mm Pitch GT - 6mm Wide - Clean

Also see combined categories:
All 2mm Pitch Timing Belts

PowerGrip(R) TruMotion(R) Timing Belts in 2.000mm.

The TruMotion(R) belt construction utilizes a cream-colored polymer compound reinforced with fiberglass tensile cord and a clean polymer-free nylon tooth facing. The belt can withstand high and low temperature ranges of -40oF to +220oF, has a virtually dust-free operation and is non-marking. The belt also has a high flex life and resistance to elongation. GT3 will replace GT2 as stock is depleted. Pitch (P) - 2.00mm, Tooth Height (H) - 0.76mm, Belt Height (W) - 1.52mm. Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength.

Related Information:

There is also a good range of Belts - Metric Timing - 2.000mm Pitch GT - 6mm Wide - Clean on the Small Parts and Bearings website.


Belts - Metric Timing - 2.000mm Pitch GT - 6mm Wide - Standard
Belts - Metric Timing - 2.000mm Pitch GT - 6mm Wide - Standard

Also see combined categories:
All 2mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 2.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 2.000mm Pitch GT - 6mm Wide - Standard on the Small Parts and Bearings website.


Belts - Metric Timing - 2.000mm Pitch GT - 9mm Wide
Belts - Metric Timing - 2.000mm Pitch GT - 9mm Wide

Also see combined categories:
All 2mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 2.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 2.000mm Pitch GT - 9mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 3.000mm Pitch GT - 15mm Wide
Belts - Metric Timing - 3.000mm Pitch GT - 15mm Wide

Also see combined categories:
All 3mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.14mm. Belt Height (W) - 2.41mm. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 3.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 3.000mm Pitch GT - 15mm Wide on the Small Parts and Bearings website.


Belts - Metric Timing - 3.000mm Pitch GT - 6mm Wide - Double Sided
Belts - Metric Timing - 3.000mm Pitch GT - 6mm Wide - Double Sided

Also see combined categories:
All 3mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts Double Sided

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.22mm. Belt Height (W) - 3.20mm. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 3.000mm.

Related Information:

There is also a good range of Belts - Metric Timing - 3.000mm Pitch GT - 6mm Wide - Double Sided on the Small Parts and Bearings website.





Main Pages

5 Axis Machine Tool Bearings About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Distributor Locations Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Satellite Reaction Wheels Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 227672 products in 2186 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 227672 products in 2186 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.