Miniature Bearings Australia Pty Ltd

Tolerance Rings Categories


Rings - Tolerance
Rings - Tolerance


Tolerance rings allow looser tolerances for assembly of parts such as bearings, pulleys and gears.

Allows looser tolerances of components. Ideal for mounting ball bearings. Useful for salvaging worn parts. Permits low cost assembly by eliminating the need for conventional fasteners. Use Torque Transfer figures for gears and pulleys. Non torque transfer figures are for bearing applications.

There is also a good range of Rings - Tolerance on the Small Parts and Bearings website.


You may also be interested in

Linear Bearings


Bearings - Linear - Ball - Miniature - Super High Precision
Bearings - Linear - Ball - Miniature - Super High Precision

Also see combined categories:
All Closed Linear Ball Bearings

High Precision Corrosion Resistant Miniature Linear Bearings.

High Precision Swiss Made, Accurate Guiding, Smooth Running. High Load Capacity. Tolerances --- d (+0.008 / -0.000 mm) D (+0.000 / -0.010 mm). Recommended Outer ring fitted with interferance of 1-3 Microns or retained by Circlips. Shafts (not included) should be 60-63 Rockwell C hardness with tolerances +0.000 / -0.006 mm.

Related Information:

There is also a good range of Bearings - Linear - Ball - Miniature - Super High Precision on the Small Parts and Bearings website.


Bearings - Linear - Ball - Closed
Bearings - Linear - Ball - Closed

Also see combined categories:
All Closed Linear Ball Bearings

Standard closed type to run on standard 60HRC shafts with h6 tolerances

Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous. This category may be available in the new MBA online store at Bearings - Linear - Ball - Closed.

Related Information:


Bearings - Linear - Ball - Stainless Steel - Closed
Bearings - Linear - Ball - Stainless Steel - Closed

Also see combined categories:
All Closed Linear Ball Bearings

Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.

Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous. This category may be available in the new MBA online store at Bearings - Linear - Ball - Stainless Steel - Closed.

Related Information:

There is also a good range of Bearings - Linear - Ball - Stainless Steel - Closed on the Small Parts and Bearings website.


Shafting Precision Ground


Shafting - Ground - Precision - Titanium - High Strength
Shafting - Ground - Precision - Titanium - High Strength

Also see combined categories:
All Shafting
All Titanium Shafting

Titanium shafting available in oversized and undersized tolerances

Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5, 6Al-4V, TC4 is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent. Shaft with undersized tolerances is suitable for use with precision ground bearings wih inner rings. HRC 36. Surface Finish Ra 0.8-1.6 um. Not suitable for running needle bearings directly. Shaft with oversized tolerances is suitable for pulleys or gears requiring interference fits, or for machining to your required tolerances.

Related Information:

There is also a good range of Shafting - Ground - Precision - Titanium - High Strength on the Small Parts and Bearings website.


Circlips


Circlips - Internal - Standard - Carbon Steel
Circlips - Internal - Standard - Carbon Steel

Also see combined categories:
All Internal Circlips

Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).

Plain carbon steel. Tolerances on request. This category may be available in the new MBA online store at Circlips - Internal - Standard - Carbon Steel.

Related Information:

There is also a good range of Circlips - Internal - Standard - Carbon Steel on the Small Parts and Bearings website.


Circlips - Internal - Standard - Zinc Plated
Circlips - Internal - Standard - Zinc Plated

Also see combined categories:
All Internal Circlips

Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).

Zinc plated carbon steel. Tolerances on request. This category may be available in the new MBA online store at Circlips - Internal - Standard - Zinc Plated.

Related Information:

There is also a good range of Circlips - Internal - Standard - Zinc Plated on the Small Parts and Bearings website.


Bearings Stainless Special Grades


Bearings - Ball - AISI304 Stainless Steel
Bearings - Ball - AISI304 Stainless Steel

Also see combined categories:
All 300 Grade Stainless Bearings

Corrosion and Heat resistance - Non Magnetic - Non Hardenable. Quality Japanese manufacture.

Tolerances differ from standard bearing types - see below. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. ID +0.05 / -0 mm , OD +0 / -0.03 mm up to 10mm bore, Width +0/- 0.12 mm. Mid range speed and load between 304 stainless and 440C stainless. Rubber seals are Nitrile but fluorine rubber may be available on request. Cages, balls, races and shields from AISI 304 Stainless Steel.

Related Information:


Springs Disc


Washers - Disc Spring - Flange Locking Type
Washers - Disc Spring - Flange Locking Type

Also see combined categories:
All Disc Springs

Used under the nuts or bolt head in bolted flange joints that are subject to thermal or mechanical shock.

The discs deflect and move with the bolted joint. Helps to compensate for loosening that may develop preventing damage and leaks caused by thermal expansion, contraction and shock. Made from 17.7 PH Stainless Steel. Temperature range minus 220 to +300o Celsius. Load tolerance +/- 20% of load shown.

There is also a good range of Washers - Disc Spring - Flange Locking Type on the Small Parts and Bearings website.


Washers - Flat - Brass - Precision Shim
Washers - Flat - Brass - Precision Shim

Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Precision Tolerances. Standard and laminated brass shim washers.

This category may be available in the new MBA online store at Washers - Flat - Brass - Precision Shim.

Related Information:

There is also a good range of Washers - Flat - Brass - Precision Shim on the Small Parts and Bearings website.


Washers - Flat - Copper - Precision Shim
Washers - Flat - Copper - Precision Shim

Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Precision Tolerances.

This category may be available in the new MBA online store at Washers - Flat - Copper - Precision Shim.

Related Information:

There is also a good range of Washers - Flat - Copper - Precision Shim on the Small Parts and Bearings website.


Washers - Flat - Stainless Steel - Precision Shim
Washers - Flat - Stainless Steel - Precision Shim

Also see combined categories:
All Precision Shim Washers
All Flat Washers and Spacers - Metallic

Precision Tolerances.

This category may be available in the new MBA online store at Washers - Flat - Stainless Steel - Precision Shim.

Related Information:

There is also a good range of Washers - Flat - Stainless Steel - Precision Shim on the Small Parts and Bearings website.


Couplings - Neo-Flex
Couplings - Neo-Flex


0.71 to 1.27 Nm.

303 stainless steel with 73 durometer neoprene centre. Shaft to shaft insulation. Torsional vibration isolation. Ribbed style are more flexible than smooth style. Bore Tolerances: +0.025 / -0.000.

Related Information:

There is also a good range of Couplings - Neo-Flex on the Small Parts and Bearings website.


Circlips - Internal - Standard - Stainless Steel
Circlips - Internal - Standard - Stainless Steel

Also see combined categories:
All Internal Circlips

Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).

PH15-7 Mo Stainless Steel. Tolerances on request. This category may be available in the new MBA online store at Circlips - Internal - Standard - Stainless Steel.

Related Information:

There is also a good range of Circlips - Internal - Standard - Stainless Steel on the Small Parts and Bearings website.


Bearings - Ball - Semi-Ground - Sealed
Bearings - Ball - Semi-Ground - Sealed

Also see combined categories:
All Radial Ball Bearings

Radial ball bearings. This series is precision ground on all contact surfaces except the bore. Recommended for lighter loads and maximum speed of 3000rpm. Bore tolerance is +0.127/-0.000, OD tolerance is +0.000/-0.013 and width is +0.000/-0.127

This category may be available in the new MBA online store at Bearings - Ball - Semi-Ground - Sealed.

There is also a good range of Bearings - Ball - Semi-Ground - Sealed on the Small Parts and Bearings website.


Bearings - Ball - Semi-Ground - Shielded
Bearings - Ball - Semi-Ground - Shielded

Also see combined categories:
All Radial Ball Bearings

Radial ball bearings. This series is precision ground on all contact surfaces except the bore. Recommended for lighter loads and maximum speed of 3000rpm. Bore tolerance is +0.127/-0.000, OD tolerance is +0.000/-0.013 and width is +0.000/-0.127

This category may be available in the new MBA online store at Bearings - Ball - Semi-Ground - Shielded.

There is also a good range of Bearings - Ball - Semi-Ground - Shielded on the Small Parts and Bearings website.


Circlips - External - Bevelled
Circlips - External - Bevelled

Also see combined categories:
All External Circlips

N1402 / VSH / 5102 / 16630. Retaining rings. Snap Rings (USA).

A 15 Deg. bevel on the inside diameter to be fitted to a 15% bevel on the load bearing groove wall. Will yield rigid end-play take-up of manufacturing tolerances or wear on the retained part. Used in greasy or oily environments. This category may be available in the new MBA online store at Circlips - External - Bevelled.

Related Information:

There is also a good range of Circlips - External - Bevelled on the Small Parts and Bearings website.


Magnets - Ceramic Blocks
Magnets - Ceramic Blocks

Also see combined categories:
All Magnets
All Ceramic Magnets

Low cost, light weight, high energy material

Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.

There is also a good range of Magnets - Ceramic Blocks on the Small Parts and Bearings website.


Feeler Gauge Stock - Stainless
Feeler Gauge Stock - Stainless


Used for close spacing and extremely tight tolerance situation.

Rc45-55 hardness. 300 grade stainless. Short flat lengths have rounded ends and are marked for size. Coiled lengths are etched every 6 inches and can be easily cut to length. 12.7mm wide.

There is also a good range of Feeler Gauge Stock - Stainless on the Small Parts and Bearings website.


Balls - Tungsten Carbide
Balls - Tungsten Carbide

Also see combined categories:
All Metallic Balls

Extreme hardness and wear resistance.

Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Precision Grade: Grade 25. Hardness: Rockwell A: 91.5 (Approx 77 Rockwell C). Extreme hardness and wear resistance. Specific Gravity: 14.95.

Related Information:

There is also a good range of Balls - Tungsten Carbide on the Small Parts and Bearings website.


Circlips - Internal - Bevelled
Circlips - Internal - Bevelled

Also see combined categories:
All Internal Circlips

N1302 / VHO / 16631 / 9002 / N5002. Retaining rings. Snap Rings (USA).

A 15 Deg. bevel on the outside diameter to be fitted to a 15% bevel on the load bearing groove wall. Will yield rigid end-play take-up of manufacturing tolerances or wear on the retained part. Used in greasy or oily environments. This category may be available in the new MBA online store at Circlips - Internal - Bevelled.

Related Information:

There is also a good range of Circlips - Internal - Bevelled on the Small Parts and Bearings website.


Bearings - Ball - 17-4PH Stainless Steel
Bearings - Ball - 17-4PH Stainless Steel

Also see combined categories:
All 300 Grade Stainless Bearings

Excellent Corrosion and Heat resistance - Hardness is between 300 grades and 400 grades. SUS630 grade.

Standard bearing tolerances. Low load, low speed applications requiring maximum corrosion resistance. Rubber seals are Nitrile but fluorine rubber may be available on request. Cages and shields from AISI 304 Stainless Steel. Balls and races from SUS630 (17-4PH) Stainless Steel.

Related Information:


Balls - Plastic - Polypropylene
Balls - Plastic - Polypropylene

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

Excellent for liquid level float applications.

Tolerance and sphericity: up to and including 25.4mm diameter = + / -0.0508mm, over 25.4mm diameter +/-0.0762mm. Very resistant to most acids and alkalies. Excellent for liquid level float applications. Unpolished. Specific Gravity: 0.91.

Related Information:

There is also a good range of Balls - Plastic - Polypropylene on the Small Parts and Bearings website.


Washers - Disc Spring - Plastic
Washers - Disc Spring - Plastic

Also see combined categories:
All Disc Springs

Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb(R) material.

There is also a good range of Washers - Disc Spring - Plastic on the Small Parts and Bearings website.


Feeler Gauge Stock - C1095 Carbon Steel
Feeler Gauge Stock - C1095 Carbon Steel


Used for close spacing and extremely tight tolerance situation.

Rc48-62 hardness. High carbon steel. Short flat lengths have rounded ends and are marked for size. Coiled lengths are etched every 6 inches and can be easily cut to length. 12.7mm wide.

There is also a good range of Feeler Gauge Stock - C1095 Carbon Steel on the Small Parts and Bearings website.


Bearings - Ball - 316 Stainless Steel - Single Row - Sealed
Bearings - Ball - 316 Stainless Steel - Single Row - Sealed

Also see combined categories:
All 300 Grade Stainless Bearings

Marine, food and medical grade Stainless Steel - Non Hardenable. Polyethylene plastic seals.

Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races, greased. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.

Related Information:

There is also a good range of Bearings - Ball - 316 Stainless Steel - Single Row - Sealed on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur G - Flanged
Bushes - Plastic - Iglidur G - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur G - Flanged on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur G - Unflanged
Bushes - Plastic - Iglidur G - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur G - Unflanged on the Small Parts and Bearings website.


Clamps - Gear - Split
Clamps - Gear - Split

Also see combined categories:
All Gear Clamps

Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.

Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.

Related Information:

There is also a good range of Clamps - Gear - Split on the Small Parts and Bearings website.


Balls - Plastic - Nylon
Balls - Plastic - Nylon

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

Resists alkalies, weak acids and most organic solvents.

Tolerances available on request. Nylon (Polyamide 6/6). Resists alkalies, weak acids and most organic solvents. Low water absorption. Unpolished. Specific Gravity: 1.14.

Related Information:

There is also a good range of Balls - Plastic - Nylon on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur M250 - Flanged
Bushes - Plastic - Iglidur M250 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur M250 - Flanged on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur M250 - Unflanged
Bushes - Plastic - Iglidur M250 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur M250 - Unflanged on the Small Parts and Bearings website.


Clamps - Gear - Screw Type
Clamps - Gear - Screw Type

Also see combined categories:
All Gear Clamps

Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.

Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.

Related Information:

There is also a good range of Clamps - Gear - Screw Type on the Small Parts and Bearings website.


Balls - Plastic - Acrylic
Balls - Plastic - Acrylic

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

Resistance to weather and sunlight. Good abrasion resistance.

Diametrical tolerances typically + / - 0.08 or 0.13 mm depending on size. Acrylic (Methyl Methacrylate). Resistance to weather and sunlight. Good abrasion resistance. Water clear transparent. Polished. Ground and Polished.

Related Information:

There is also a good range of Balls - Plastic - Acrylic on the Small Parts and Bearings website.


Balls - Plastic - PTFE
Balls - Plastic -  PTFE

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

No water absorption. Temperatures up to 288 Deg C.

Tolerances available on request. Not affected by any known acids or alkalies. No water absorption. Temperatures up to 288 oC. Unpolished. Specific Gravity: 2.3.

Related Information:

There is also a good range of Balls - Plastic - PTFE on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur J - Flanged
Bushes - Plastic - Iglidur J - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur J - Flanged on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur J - Unflanged
Bushes - Plastic - Iglidur J - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur J - Unflanged on the Small Parts and Bearings website.


Bearings - Ball - 316 Stainless Steel - Single Row - Shielded
Bearings - Ball - 316 Stainless Steel - Single Row - Shielded

Also see combined categories:
All 300 Grade Stainless Bearings

Marine, food and medical grade Stainless Steel - Non Hardenable. 316 stainless steel shields.

Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Stainless steel 316 cage, grade 200 type 316 stainless balls, 316 stainless races, 316 stainless steel shields. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.

Related Information:

There is also a good range of Bearings - Ball - 316 Stainless Steel - Single Row - Shielded on the Small Parts and Bearings website.


Balls - Ceramic - Ruby - Synthetic
Balls - Ceramic - Ruby - Synthetic

Also see combined categories:
All Ceramic Balls
All Non Metallic Balls

Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.

Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Specific Gravity: 3.98.

Related Information:

There is also a good range of Balls - Ceramic - Ruby - Synthetic on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur Q - Flanged
Bushes - Plastic - Iglidur Q - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Excellent wear resistance under high load. Resistant to dirt.

Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur Q - Flanged on the Small Parts and Bearings website.


Balls - Ceramic - Sapphire - Synthetic
Balls - Ceramic - Sapphire - Synthetic

Also see combined categories:
All Ceramic Balls
All Non Metallic Balls

Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.

Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Specific Gravity: 3.98. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Transparent (refractive index 1.76).

Related Information:

There is also a good range of Balls - Ceramic - Sapphire - Synthetic on the Small Parts and Bearings website.


Balls - Plastic - Acetal
Balls - Plastic - Acetal

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

High intensity strength, rigidity, outstanding resistance to abrasion and most solvents.

Tolerances available on request. Acetal Copolymer. High intensity strength, rigidity, outstanding resistance to abrasion and most solvents. Standard Opaque White. Specific Gravity: 1.4.

Related Information:

There is also a good range of Balls - Plastic - Acetal on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur F - Unflanged
Bushes - Plastic - Iglidur F - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.

Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur F - Unflanged on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur W300 - Flanged
Bushes - Plastic - Iglidur W300 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur W300 - Flanged on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur W300 - Unflanged
Bushes - Plastic - Iglidur W300 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur W300 - Unflanged on the Small Parts and Bearings website.


Washers - Disc Spring - Ball Bearing Type
Washers - Disc Spring - Ball Bearing Type

Also see combined categories:
All Disc Springs

Specially designed for preloading the outer ring of ball bearings. C1075 steel. Includes disc springs to DIN 2093.

Ensures perfect bearing positioning with no sideways play. May be used to provide bearing preload. Load tolerance +/- 20% of load shown. This category may be available in the new MBA online store at Washers - Disc Spring - Ball Bearing Type.

There is also a good range of Washers - Disc Spring - Ball Bearing Type on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur H370 - Unflanged
Bushes - Plastic - Iglidur H370 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.

Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur H370 - Unflanged on the Small Parts and Bearings website.


Bearings - U Groove Profile OD
Bearings - U Groove Profile OD


Special OD Bearings.

Contact us for tolerances. This category may be available in the new MBA online store at Bearings - U Groove Profile OD.

Related Information:

There is also a good range of Bearings - U Groove Profile OD on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur A200 - Flanged
Bushes - Plastic - Iglidur A200 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur A200 - Flanged on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur A200 - Unflanged
Bushes - Plastic - Iglidur A200 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur A200 - Unflanged on the Small Parts and Bearings website.





Main Pages

5 Axis Machine Tool Bearings About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Charity Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Distributor Locations Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Satellite Reaction Wheels Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 212690 products in 2107 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 212690 products in 2107 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.