Tolerance Rings Categories
Rings - Tolerance
Tolerance rings allow looser tolerances for assembly of parts such as bearings, pulleys and gears.
Allows looser tolerances of components. Ideal for mounting ball bearings. Useful for salvaging worn parts. Permits low cost assembly by eliminating the need for conventional fasteners. Use Torque Transfer figures for gears and pulleys. Non torque transfer figures are for bearing applications.
There is also a good range of Rings - Tolerance on the Small Parts and Bearings website.
You may also be interested in
Linear Bearings
Bearings - Linear Ball - Miniature - Super High Precision
High Precision Corrosion Resistant Miniature Linear Bearings.
High Precision Swiss Made, Accurate Guiding, Smooth Running. High Load Capacity. Tolerances --- d (+0.008 / -0.000 mm) D (+0.000 / -0.010 mm). Recommended Outer ring fitted with interferance of 1-3 Microns or retained by Circlips. Shafts (not included) should be 60-63 Rockwell C hardness with tolerances +0.000 / -0.006 mm.
Related Information:
There is also a good range of Bearings - Linear Ball - Miniature - Super High Precision on the Small Parts and Bearings website.
Bearings Stainless Special Grades
Bearings - Single Row Ball Unflanged - Standard - 316 Stainless - Open
Marine, food and medical grade Stainless Steel - Non Hardenable. Open, easier to lubricate. Water lubrication is ok.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance.
Related Information:
There is also a good range of Bearings - Single Row Ball Unflanged - Standard - 316 Stainless - Open on the Small Parts and Bearings website.
Linear Bearings
Bearings - Linear Ball - Chrome Steel - Closed
Standard closed type to run on standard 60HRC shafts with h6 tolerances
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous. This category may be available in the new MBA online store at Bearings - Linear Ball - Chrome Steel - Closed.
Related Information:
Bearings - Linear Ball - Stainless Steel - Closed
Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous. This category may be available in the new MBA online store at Bearings - Linear Ball - Stainless Steel - Closed.
Related Information:
There is also a good range of Bearings - Linear Ball - Stainless Steel - Closed on the Small Parts and Bearings website.
Shafting Precision Ground
Shafting - Ground - Precision - Titanium - High Strength
Titanium shafting available in oversized and undersized tolerances
Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5, 6Al-4V, TC4 is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent. Shaft with undersized tolerances is suitable for use with precision ground bearings wih inner rings. HRC 36. Surface Finish Ra 0.8-1.6 um. Not suitable for running needle bearings directly. Shaft with oversized tolerances is suitable for pulleys or gears requiring interference fits, or for machining to your required tolerances.
Related Information:
There is also a good range of Shafting - Ground - Precision - Titanium - High Strength on the Small Parts and Bearings website.
Circlips
Circlips - Internal - Standard - Carbon Steel
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).
Plain carbon steel. Tolerances on request. This category may be available in the new MBA online store at Circlips - Internal - Standard - Carbon Steel.
Related Information:
There is also a good range of Circlips - Internal - Standard - Carbon Steel on the Small Parts and Bearings website.
Circlips - Internal - Standard - Zinc Plated
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).
Zinc plated carbon steel. Tolerances on request. This category may be available in the new MBA online store at Circlips - Internal - Standard - Zinc Plated.
Related Information:
There is also a good range of Circlips - Internal - Standard - Zinc Plated on the Small Parts and Bearings website.
Springs Disc
Washers - Disc Spring - Flange Locking Type
Used under the nuts or bolt head in bolted flange joints that are subject to thermal or mechanical shock.
The discs deflect and move with the bolted joint. Helps to compensate for loosening that may develop preventing damage and leaks caused by thermal expansion, contraction and shock. Made from 17.7 PH Stainless Steel. Temperature range minus 220 to +300o Celsius. Load tolerance +/- 20% of load shown.
There is also a good range of Washers - Disc Spring - Flange Locking Type on the Small Parts and Bearings website.
Washers - Flat - Brass - Precision Shim
Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Precision Tolerances. Standard and laminated brass shim washers.
This category may be available in the new MBA online store at Washers - Flat - Brass - Precision Shim.
Related Information:
There is also a good range of Washers - Flat - Brass - Precision Shim on the Small Parts and Bearings website.
Washers - Flat - Copper - Precision Shim
Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Precision Tolerances.
This category may be available in the new MBA online store at Washers - Flat - Copper - Precision Shim.
Related Information:
There is also a good range of Washers - Flat - Copper - Precision Shim on the Small Parts and Bearings website.
Washers - Flat - Stainless Steel - Precision Shim
Precision Tolerances.
This category may be available in the new MBA online store at Washers - Flat - Stainless Steel - Precision Shim.
Related Information:
There is also a good range of Washers - Flat - Stainless Steel - Precision Shim on the Small Parts and Bearings website.
Couplings - Neo - Flex
0.71 to 1.27 Nm.
303 stainless steel with 73 durometer neoprene centre. Shaft to shaft insulation. Torsional vibration isolation. Ribbed style are more flexible than smooth style. Bore Tolerances: +0.025 / -0.000.
Related Information:
There is also a good range of Couplings - Neo - Flex on the Small Parts and Bearings website.
Bearings - Single Row Ball Unflanged - Standard - AISI304 Stainless
Corrosion and Heat resistance - Non Magnetic - Non Hardenable. Quality Japanese manufacture.
Tolerances differ from standard bearing types - see below. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. ID +0.05 / -0 mm , OD +0 / -0.03 mm up to 10mm bore, Width +0/- 0.12 mm. Mid range speed and load between 304 stainless and 440C stainless. Rubber seals are Nitrile but fluorine rubber may be available on request. Cages, balls, races and shields from AISI 304 Stainless Steel.
Related Information:
Circlips - Internal - Standard - Stainless Steel
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).
PH15-7 Mo Stainless Steel. Tolerances on request. This category may be available in the new MBA online store at Circlips - Internal - Standard - Stainless Steel.
Related Information:
There is also a good range of Circlips - Internal - Standard - Stainless Steel on the Small Parts and Bearings website.
Circlips - External - Bevelled
N1402 / VSH / 5102 / 16630. Retaining rings. Snap Rings (USA).
A 15 Deg. bevel on the inside diameter to be fitted to a 15% bevel on the load bearing groove wall. Will yield rigid end-play take-up of manufacturing tolerances or wear on the retained part. Used in greasy or oily environments. This category may be available in the new MBA online store at Circlips - External - Bevelled.
Related Information:
There is also a good range of Circlips - External - Bevelled on the Small Parts and Bearings website.
Magnets - Ceramic Blocks
Low cost, light weight, high energy material
Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.
There is also a good range of Magnets - Ceramic Blocks on the Small Parts and Bearings website.
Feeler Gauge Stock - Stainless
Used for close spacing and extremely tight tolerance situation.
Rc45-55 hardness. 300 grade stainless. Short flat lengths have rounded ends and are marked for size. Coiled lengths are etched every 6 inches and can be easily cut to length. 12.7mm wide.
There is also a good range of Feeler Gauge Stock - Stainless on the Small Parts and Bearings website.
Bearings - Single Row Semi-Ground - Sealed
Radial ball bearings. This series is precision ground on all contact surfaces except the bore. Recommended for lighter loads and maximum speed of 3000rpm. Bore tolerance is +0.127/-0.000, OD tolerance is +0.000/-0.013 and width is +0.000/-0.127
This category may be available in the new MBA online store at Bearings - Single Row Semi-Ground - Sealed.
There is also a good range of Bearings - Single Row Semi-Ground - Sealed on the Small Parts and Bearings website.
Bearings - Single Row Semi-Ground - Shielded
Radial ball bearings. This series is precision ground on all contact surfaces except the bore. Recommended for lighter loads and maximum speed of 3000rpm. Bore tolerance is +0.127/-0.000, OD tolerance is +0.000/-0.013 and width is +0.000/-0.127
This category may be available in the new MBA online store at Bearings - Single Row Semi-Ground - Shielded.
There is also a good range of Bearings - Single Row Semi-Ground - Shielded on the Small Parts and Bearings website.
Circlips - Internal - Bevelled
N1302 / VHO / 16631 / 9002 / N5002. Retaining rings. Snap Rings (USA).
A 15 Deg. bevel on the outside diameter to be fitted to a 15% bevel on the load bearing groove wall. Will yield rigid end-play take-up of manufacturing tolerances or wear on the retained part. Used in greasy or oily environments. This category may be available in the new MBA online store at Circlips - Internal - Bevelled.
Related Information:
There is also a good range of Circlips - Internal - Bevelled on the Small Parts and Bearings website.
Balls - Metallic - Tungsten Carbide
Extreme hardness and wear resistance.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Precision Grade: Grade 25. Hardness: Rockwell A: 91.5 (Approx 77 Rockwell C). Extreme hardness and wear resistance. Specific Gravity: 14.95.
Related Information:
There is also a good range of Balls - Metallic - Tungsten Carbide on the Small Parts and Bearings website.
Balls - Plastic - Polypropylene
Excellent for liquid level float applications.
Tolerance and sphericity: up to and including 25.4mm diameter = + / -0.0508mm, over 25.4mm diameter +/-0.0762mm. Very resistant to most acids and alkalies. Excellent for liquid level float applications. Unpolished. Specific Gravity: 0.91.
Related Information:
There is also a good range of Balls - Plastic - Polypropylene on the Small Parts and Bearings website.
Bushes - Plastic Flanged - Iglidur G
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic Flanged - Iglidur G on the Small Parts and Bearings website.
Bushes - Plastic Unflanged - Iglidur G
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic Unflanged - Iglidur G on the Small Parts and Bearings website.
Washers - Disc Spring - Plastic
Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb(R) material.
There is also a good range of Washers - Disc Spring - Plastic on the Small Parts and Bearings website.
Feeler Gauge Stock - C1095 Carbon Steel
Used for close spacing and extremely tight tolerance situation.
Rc48-62 hardness. High carbon steel. Short flat lengths have rounded ends and are marked for size. Coiled lengths are etched every 6 inches and can be easily cut to length. 12.7mm wide.
There is also a good range of Feeler Gauge Stock - C1095 Carbon Steel on the Small Parts and Bearings website.
Clamps - Gear - Split
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
Related Information:
There is also a good range of Clamps - Gear - Split on the Small Parts and Bearings website.
Bearings - Single Row Ball Unflanged - Standard - 316 Stainless - Sealed
Marine, food and medical grade Stainless Steel - Non Hardenable. Polyethylene plastic seals.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races, greased. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.
Related Information:
There is also a good range of Bearings - Single Row Ball Unflanged - Standard - 316 Stainless - Sealed on the Small Parts and Bearings website.
Balls - Plastic - Nylon
Resists alkalies, weak acids and most organic solvents.
Tolerances available on request. Nylon (Polyamide 6/6). Resists alkalies, weak acids and most organic solvents. Low water absorption. Unpolished. Specific Gravity: 1.14.
Related Information:
There is also a good range of Balls - Plastic - Nylon on the Small Parts and Bearings website.
Bushes - Plastic Flanged - Iglidur J
Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.
Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic Flanged - Iglidur J on the Small Parts and Bearings website.
Bushes - Plastic Flanged - Iglidur M250
For impact resistance vibration dampening unclean environments.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic Flanged - Iglidur M250 on the Small Parts and Bearings website.
Bushes - Plastic Unflanged - Iglidur J
Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.
Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic Unflanged - Iglidur J on the Small Parts and Bearings website.
Bushes - Plastic Unflanged - Iglidur M250
For impact resistance vibration dampening unclean environments.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic Unflanged - Iglidur M250 on the Small Parts and Bearings website.
Clamps - Gear - Screw Type
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
Related Information:
There is also a good range of Clamps - Gear - Screw Type on the Small Parts and Bearings website.
Bearings - Single Row Ball Unflanged - Standard - 17-4PH Stainless
Excellent Corrosion and Heat resistance - Hardness is between 300 grades and 400 grades. SUS630 grade.
Standard bearing tolerances. Low load, low speed applications requiring maximum corrosion resistance. Rubber seals are Nitrile but fluorine rubber may be available on request. Cages and shields from AISI 304 Stainless Steel. Balls and races from SUS630 (17-4PH) Stainless Steel.
Related Information:
Balls - Plastic - Acrylic
Resistance to weather and sunlight. Good abrasion resistance.
Diametrical tolerances typically + / - 0.08 or 0.13 mm depending on size. Acrylic (Methyl Methacrylate). Resistance to weather and sunlight. Good abrasion resistance. Water clear transparent. Polished. Ground and Polished.
Related Information:
There is also a good range of Balls - Plastic - Acrylic on the Small Parts and Bearings website.
Balls - Plastic - PTFE
No water absorption. Temperatures up to 288 Deg C.
Tolerances available on request. Not affected by any known acids or alkalies. No water absorption. Temperatures up to 288 oC. Unpolished. Specific Gravity: 2.3.
Related Information:
There is also a good range of Balls - Plastic - PTFE on the Small Parts and Bearings website.
Bushes - Plastic Flanged - Iglidur Q
Excellent wear resistance under high load. Resistant to dirt.
Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic Flanged - Iglidur Q on the Small Parts and Bearings website.
Balls - Ceramic - Ruby - Synthetic
Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Specific Gravity: 3.98.
Related Information:
There is also a good range of Balls - Ceramic - Ruby - Synthetic on the Small Parts and Bearings website.
Bushes - Plastic Unflanged - Iglidur F
Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.
Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic Unflanged - Iglidur F on the Small Parts and Bearings website.
Balls - Ceramic - Sapphire - Synthetic
Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Specific Gravity: 3.98. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Transparent (refractive index 1.76).
Related Information:
There is also a good range of Balls - Ceramic - Sapphire - Synthetic on the Small Parts and Bearings website.
Balls - Plastic - Acetal
High intensity strength, rigidity, outstanding resistance to abrasion and most solvents.
Tolerances available on request. Acetal Copolymer. High intensity strength, rigidity, outstanding resistance to abrasion and most solvents. Standard Opaque White. Specific Gravity: 1.4.
Related Information:
There is also a good range of Balls - Plastic - Acetal on the Small Parts and Bearings website.
Bushes - Plastic Flanged - Iglidur W300
Low co-efficient of friction. High wear resistance. Chemical resistant.
Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic Flanged - Iglidur W300 on the Small Parts and Bearings website.
Bushes - Plastic Unflanged - Iglidur W300
Low co-efficient of friction. High wear resistance. Chemical resistant.
Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic Unflanged - Iglidur W300 on the Small Parts and Bearings website.
Washers - Disc Spring - Ball Bearing Type
Specially designed for preloading the outer ring of ball bearings. C1075 steel. Includes disc springs to DIN 2093.
Ensures perfect bearing positioning with no sideways play. May be used to provide bearing preload. Load tolerance +/- 20% of load shown. This category may be available in the new MBA online store at Washers - Disc Spring - Ball Bearing Type.
There is also a good range of Washers - Disc Spring - Ball Bearing Type on the Small Parts and Bearings website.
Bearings - Single Row Ball Unflanged - Standard - 316 Stainless - Shields
Marine, food and medical grade Stainless Steel - Non Hardenable. 316 stainless steel shields.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Stainless steel 316 cage, grade 200 type 316 stainless balls, 316 stainless races, 316 stainless steel shields. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.
Related Information:
There is also a good range of Bearings - Single Row Ball Unflanged - Standard - 316 Stainless - Shields on the Small Parts and Bearings website.
Bushes - Plastic Unflanged - Iglidur H370
Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.
Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic Unflanged - Iglidur H370 on the Small Parts and Bearings website.
Bearings - Grooved OD - U Groove
Special OD Bearings.
Contact us for tolerances. This category may be available in the new MBA online store at Bearings - Grooved OD - U Groove.
Related Information:
There is also a good range of Bearings - Grooved OD - U Groove on the Small Parts and Bearings website.
Bushes - Plastic Flanged - Iglidur A200
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic Flanged - Iglidur A200 on the Small Parts and Bearings website.
Main Pages
5 Axis Machine Tool Bearings
About Us
Acetal Bearings PDF
ADR and SKF PDF
Anderton Circlips Cross Reference PDF
Ball Lock Pins PDF
Balls List
Balls PDF
Barden Bearings Cross Reference PDF
Bearings List
Brands
Ceramic Bearings PDF
Circlips PDF
Clearance Items List
Clevis Pins PDF
Contact Us
Corrosion Resistant Bearings PDF
Dental Bearings
Disc Springs PDF
Distributor Locations
Dowel Pins PDF
Dowel Pins
Economy Bearings PDF
Essentra Cross Reference PDF
Flocast Cross Reference PDF
Freight Rates and Shipping Times
Frequently Asked Questions
General Information about MBA
Hammer Drive Pins PDF
High Speed Bearings PDF
Hobby Clearance
Hobby Information
K&S Metals Cross Reference PDF
Key Steel PDF
Knobs PDF
Large Bearings
Leveling Mounts PDF
Mailorder Form
Metallic Bushes PDF
Miniature Precison Bearings Cross Reference PDF
Miscellaneous Brands Cross Reference PDF
Nordex Cross Reference PDF
NSK and NTN Cross Reference PDF
Ondrives Cross Reference PDF
O-Rings PDF
Pins PDF
Plastic Bearings PDF
Polyvee Belts and Pulleys PDF
Precision Shim Washers PDF
Privacy
Push On and Push In Rings PDF
Reid Supply Cross Reference PDF
Rod & Tube PDF
Roll Pins PDF
Satellite Reaction Wheels
Screws PDF
SDP-SI Designatronics Cross Reference PDF
Seeger Circlips Cross Reference PDF
Shaft Collars PDF
Shim Sheet PDF
Shoulder Screws PDF
Sintered Bronze Bushes PDF
Sintered Bronze Cross Reference PDF
Small Bearings
Small Parts Inc Cross Reference PDF
Snap Rings PDF
Socket Set Screws PDF
Solid Bronze Bushes PDF
Spring Steel Strip PDF
Springs PDF
Standard Ball Bearing Range PDF
Super Precision Bearings PDF
Taper Pins PDF
Technical Information
Terms
Thrust Bearings PDF
Thumb Screws and Nuts PDF
Timing Belts and Pulleys Cross Reference PDF
Timing Belts PDF
Timing Pulley Stock PDF
Timing Pulleys PDF
Vibration Mounts PDF
Washers and Spacers PDF
Wave Washers PDF
Domains
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)
Miniature Bearings Australia offers 227673 products in 2186 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.
