Tolerance Rings Categories

Circlips - Internal - Standard - Carbon Steel

Search Rating: 64%

Also see combined categories:
All Internal Circlips

Imperial and metric DIN471 and 472 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).

Plain carbon steel. Tolerances on request. Standard and heavy duty options.

Circlips - Internal - Standard - Zinc Plated

Search Rating: 64%

Also see combined categories:
All Internal Circlips

Imperial and metric DIN471 and 472 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).

Zinc plated carbon steel. Tolerances on request. Standard and heavy duty options.

Circlips - Internal - Standard - Stainless Steel

Search Rating: 63%

Also see combined categories:
All Internal Circlips

Imperial and metric DIN471 and 472 / N1300 / Seeger J and JS. 420 Stainless Steel. Retaining rings. Snap Rings (USA).

420 Stainless Steel. Tolerances on request. Standard and heavy duty options.

Washers - Disc Spring - Ball Bearing Type

Search Rating: 58%

Also see combined categories:
All Disc Springs

Specially designed for preloading the outer ring of ball bearings. C1075 steel. Also known as belleville washers.

Ensures perfect bearing positioning with no sideways play. May be used to provide bearing preload. Load tolerance +/- 20% of load shown.

Circlips - Internal - Bevelled

Search Rating: 58%

Also see combined categories:
All Internal Circlips

N1302 / VHO / 16631 / 9002 / N5002. Retaining rings. Snap Rings (USA).

A 15 Deg. bevel on the outside diameter to be fitted to a 15% bevel on the load bearing groove wall. Will yield rigid end-play take-up of manufacturing tolerances or wear on the retained part. Used in greasy or oily environments.

Bearings - Linear - Ball - Miniature - Super High Precision

Search Rating: 58%

Also see combined categories:
All Closed Linear Ball Bearings

High Precision Corrosion Resistant Miniature Linear Bearings.

High Precision Swiss Made, Accurate Guiding, Smooth Running. High Load Capacity. Tolerances --- d (+0.008 / -0.000 mm) D (+0.000 / -0.010 mm). Recommended Outer ring fitted with interferance of 1-3 Microns or retained by Circlips. Shafts (not included) should be 60-63 Rockwell C hardness with tolerances +0.000 / -0.006 mm.

Bearings - U Groove Profile OD

Search Rating: 56%

Also see combined categories:
All U Groove Bearings and Pulleys

Special OD Bearings.

Contact us for tolerances.

Latches - Pawl - 1-4 Turn

Search Rating: 56%

An ideal fastener for gasketed doors and access panels subject to wide thickness or misalignment tolerances.

Grip length is variable from 3.2mm to 36.5mm and is set by rotating the centre spindle. Latch can be opened with a quarter turn of the outer ring. Steel with black plastic outer ring. Installation hole diameter 19.43mm. Instructions included. Panel thickness from 1.2 to 3.2mm max. The catch on these latches may be supplied either standard, inverted or flat depending on the grip range. Catches are not reversible.

Bearings - Ball - 316 Stainless Steel - Single Row - Open

Search Rating: 55%

Also see combined categories:
All 300 Grade Stainless Bearings

Marine, food and medical grade Stainless Steel - Non Hardenable. Open, easier to lubricate. Water lubrication is ok.

Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance.

Bearings - Linear - Ball - Closed

Search Rating: 55%

Also see combined categories:
All Closed Linear Ball Bearings

Standard closed type to run on standard 60HRC shafts with h6 tolerances

Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 ^oC Intermittent, 80 Deg C continuous.

Bearings - Linear - Ball - Stainless Steel - Closed

Search Rating: 54%

Also see combined categories:
All Closed Linear Ball Bearings

Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.

Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 ^oC Intermittent, 80 Deg C continuous.

Rod - Round - Acetal

Search Rating: 53%

Also see combined categories:
All Plastic Rod

Hard, stiff plastic for machining bushes, gears etc with close tolerances. Sizes listed are FINISHED SIZE. Product supplied will be larger.

Specific Gravity 1.41 g/cm3 - Operating Temp -40 to 120 C. Tensile Strength 60-70 Mpa / Hardness 80 Rockwell M. Small diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.

Housings - Igubal - Sliding

Search Rating: 53%

Also see combined categories:
All Housings with Integral Bearing

Housing: Aluminium. Insert: Sliding film Iglidur^(R) J. Tolerance for the Shaft: h7. Use with Drylin aluminium shafts.

Bearings - Ball - 304 Stainless Steel

Search Rating: 52%

Also see combined categories:
All 300 Grade Stainless Bearings

Corrosion and Heat resistance - Non Magnetic - Unhardened.

Tolerances differ from standard bearing types - see below. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. ID +0.05 / -0 mm , OD +0 / -0.03 mm, Width +0/- 0.12 mm. Low load, low speed applications requiring maximum corrosion resistance. Non Magnetic. Cages, balls, races and shields from AISI 304 Stainless Steel.

Rollers - Feed - With Aluminium Sleeve

Search Rating: 50%

Also see combined categories:
All Rollers

Tolerance of Roller Outside Diameter (D) is +/-0.075 mm

Urethane 60 Durometer ground outside diameter. Aluminium sleeve. Feed rollers do not have a rotating bore. They are designed to turn with the shaft.

Tools - Punches - Pilot

Search Rating: 50%

Also see combined categories:
All Punches
All Tools

Vanadium Steel. Tolerance is +0.000 / -0.254mm

Collars - Shaft - With Integral Shim

Search Rating: 50%

Also see combined categories:
All Round Bore Shaft Collars

Bore tolerance (+0.003/+0.013). Imperial Collars have undersized tolerances. Metric Collars have oversized tolerances.

Tools - Punches - Pilot - Sets

Search Rating: 50%

Also see combined categories:
All Punches
All Tools

Vanadium Steel. Tolerance is +0.000 / -0.254mm

Washers - Flat - Brass - Precision

Search Rating: 50%

Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Precision Tolerances. Laminated brass shim washers.

Balls - Chrome Steel

Search Rating: 49%

Also see combined categories:
All Metallic Balls

Hardness: Rockwell C: 60-70.

Tolerances available on request. SAE 52100 Chrome Steel. Hardness: Rockwell C: 60-70. Specific Gravity: 7.833.

E-Clips - Bowed

Search Rating: 49%

Also see combined categories:
All E-Clips

For end play take up.

Thickness tolerance +/- 0.025.

Washers - Flat - Stainless Steel - Precision Shim

Search Rating: 49%

Also see combined categories:
All Precision Shim Washers
All Flat Washers and Spacers - Metallic

Precision Tolerances.

Washers - Flat - Nylon

Search Rating: 49%

Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic

Flat washers.

Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.

Couplings - Neo-Flex

Search Rating: 49%

0.71 to 1.27 Nm.

303 stainless steel with 73 durometer neoprene centre. Shaft to shaft insulation. Torsional vibration isolation. Ribbed style are more flexible than smooth style. Bore Tolerances: +0.025 / -0.000.

Washers - Flat - Brass - Commercial

Search Rating: 49%

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers.

Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.

Bearings - Ball - Semi-Ground - Sealed

Search Rating: 48%

Also see combined categories:
All Radial Ball Bearings

Radial ball bearings. This series is precision ground on all contact surfaces except the bore. Recommended for lighter loads and maximum speed of 3000rpm. Bore tolerance is +0.127/-0.000, OD tolerance is +0.000/-0.013 and width is +0.000/-0.127

Bearings - Ball - Semi-Ground - Shielded

Search Rating: 48%

Also see combined categories:
All Radial Ball Bearings

Radial ball bearings. This series is precision ground on all contact surfaces except the bore. Recommended for lighter loads and maximum speed of 3000rpm. Bore tolerance is +0.127/-0.000, OD tolerance is +0.000/-0.013 and width is +0.000/-0.127

Balls - Stainless Steel - 440C Grade

Search Rating: 48%

Also see combined categories:
All Metallic Balls

Hardness: Rockwell C: 55-60.

Tolerances available on request. AISI440C Stainless Steel. Hardness: Rockwell C: 55-60.

Feeler Gauge Stock - Stainless

Search Rating: 48%

Used for close spacing and extremely tight tolerance situation.

Rc45-55 hardness. 300 grade stainless. Short flat lengths have rounded ends and are marked for size. Coiled lengths are etched every 6 inches and can be easily cut to length. 12.7mm wide.

Magnets - Ceramic Blocks

Search Rating: 48%

Also see combined categories:
All Magnets
All Ceramic Magnets

Low cost, light weight, high energy material

Non conductive hard brittle material. Performs best at temperatures below 249 ^oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.

Magnets - Ceramic Cylinder

Search Rating: 48%

Also see combined categories:
All Magnets
All Ceramic Magnets

Low cost, light weight, high energy material

Non conductive hard brittle material. Performs best at temperatures below 249 ^oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.

Balls - Tungsten Carbide

Search Rating: 48%

Also see combined categories:
All Metallic Balls

Extreme hardness and wear resistance.

Tolerances available on request. Precision Grade: Grade 25. Hardness: Rockwell A: 91.5 (Approx 77 Rockwell C). Extreme hardness and wear resistance. Specific Gravity: 14.95.

Bearings - Ball - 316 Stainless Steel - Single Row - Sealed

Search Rating: 48%

Also see combined categories:
All 300 Grade Stainless Bearings

Marine, food and medical grade Stainless Steel - Non Hardenable. Polyethylene plastic seals.

Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races, greased. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.

Washers - Disc Spring - Flange Locking Type

Search Rating: 48%

Also see combined categories:
All Disc Springs

Used under the nuts or bolt head in bolted flange joints that are subject to thermal or mechanical shock. Also known as belleville washers.

The discs deflect and move with the bolted joint. Helps to compensate for loosening that may develop preventing damage and leaks caused by thermal expansion, contraction and shock. Made from 17.7 PH Stainless Steel. Temperature range minus 220 to +300^o Celsius. Load tolerance +/- 20% of load shown.

Rod - Round - Carbon Fibre

Search Rating: 48%

Also see combined categories:
All Non Metallic Rod - Round

High impact light weight carbon fibre for modelling.

Pultruded carbon fibre with a smooth epoxy coated finish. Items marked as Low Grade may have tolerance variations up to 0.2mm.

Balls - Plastic - Polypropylene

Search Rating: 47%

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

Excellent for liquid level float applications.

Tolerance and spherecity: up to and including 25.4mm diameter = +/-0.0508mm, over 25.4mm diameter +/-0.0762mm. Very resistant to most acids and alkalies. Excellent for liquid level float applications. Unpolished. Specific Gravity: 0.91.

Hubs - Gear and Dial - Single

Search Rating: 47%

Also see combined categories:
All Hubs

Fairloc^tm Hubs require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.

Feeler Gauge Stock - C1095 Carbon Steel

Search Rating: 47%

Used for close spacing and extremely tight tolerance situation.

Rc48-62 hardness. High carbon steel. Short flat lengths have rounded ends and are marked for size. Coiled lengths are etched every 6 inches and can be easily cut to length. 12.7mm wide.

Rail Supports - With Shaft

Search Rating: 47%

Also see combined categories:
All Shaft Supports

Includes linear shafting.

Includes shaft to h6 tolerances. Support is made from aluminium.

Bushes - Plastic - Iglidur G - Flanged

Search Rating: 47%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 ^oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerances is E10 after H7 Pressfit. Tolerances listed in the tables take this into account.

Bushes - Plastic - Iglidur G - Unflanged

Search Rating: 47%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 ^oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerances is E10 after H7 Pressfit. Tolerances listed in the tables take this into account.

Bushes - Plastic - Iglidur H - Flanged

Search Rating: 47%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Underwater performance. High Temp. Chemical Resistance.

Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 ^oC = 175 Mpa. Hardness 87 Shore D (DIN53505). Bushing bore tolerances is F10 after H7 Pressfit. Tolerances listed in the tables take this into account.

Bushes - Plastic - Iglidur H - Unflanged

Search Rating: 47%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Underwater performance. High Temp. Chemical Resistance.

Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 ^oC = 175 Mpa. Hardness 87 Shore D (DIN53505). Bushing bore tolerances is F10 after H7 Pressfit. Tolerances listed in the tables take this into account.

Clamps - Gear - Split

Search Rating: 47%

Also see combined categories:
All Gear Clamps

Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.

Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.

Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends

Search Rating: 47%

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - DIN7

Diameter tolerances are m6.

Balls - Plastic - Nylon

Search Rating: 47%

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

Resists alkalies, weak acids and most organic solvents.

Tolerances available on request. Nylon (Polyamide 6/6). Resists alkalies, weak acids and most organic solvents. Low water absorption. Unpolished. Specific Gravity: 1.14.

Bushes - Plastic - Iglidur M250 - Flanged

Search Rating: 47%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 ^oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerances is D11 after H7 Pressfit. Tolerances listed in the tables take this into account.

Bushes - Plastic - Iglidur M250 - Unflanged

Search Rating: 47%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 ^oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerances is D11 after H7 Pressfit. Tolerances listed in the tables take this into account.

Bushes - Plastic - Iglidur P - Flanged

Search Rating: 47%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low water absorption. Low wear. Hgh load.

Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 ^oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerances is E10 after H7 Pressfit. Tolerances listed in the tables take this into account.

Bushes - Plastic - Iglidur P - Unflanged

Search Rating: 47%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low water absorption. Low wear. Hgh load.

Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 ^oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerances is E10 after H7 Pressfit. Tolerances listed in the tables take this into account.

Clamps - Gear - Screw Type

Search Rating: 47%

Also see combined categories:
All Gear Clamps

Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.

Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.

Washers - Flat - Stainless Steel 304 - Commercial

Search Rating: 47%

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers.

Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.

Washers - Flat - Stainless Steel 316 - Commercial

Search Rating: 47%

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Flat washers.

Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.

Bearings - Ball - 316 Stainless Steel - Single Row - Shielded

Search Rating: 47%

Also see combined categories:
All 300 Grade Stainless Bearings

Marine, food and medical grade Stainless Steel - Non Hardenable. 316 stainless steel shields.

Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Stainless steel 316 cage, grade 200 type 316 stainless balls, 316 stainless races, 316 stainless steel shields. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.

Balls - Plastic - Acrylic

Search Rating: 46%

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

Resistance to weather and sunlight. Good abrasion resistance.

Diametrical tolerances typically +/- 0.08 or 0.13 mm depending on size. Acrylic (Methyl Methacrylate). Resistance to weather and sunlight. Good abrasion resistance. Water clear transparent. Polished. Ground and Polished.

Balls - Plastic - PTFE

Search Rating: 46%

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

No water absorption. Temperatures up to 288 Deg C.

Tolerances available on request. Not affected by any known acids or alkalies. No water absorption. Temperatures up to 288 ^oC. Unpolished. Specific Gravity: 2.3.

Bushes - Plastic - Iglidur J - Flanged

Search Rating: 46%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 ^oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerances is E10 after H7 Pressfit. Tolerances listed in the tables take this into account.

Bushes - Plastic - Iglidur J - Unflanged

Search Rating: 46%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 ^oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerances is E10 after H7 Pressfit. Tolerances listed in the tables take this into account.

Latches - Adjustable Draw - With Hook - Stainless

Search Rating: 46%

Threaded rod allows periodic adjustments where gasketing and material tolerances may vary. Passivated 300 Grade Stainless Steel.

Latches - Adjustable Draw - With Hook - Steel

Search Rating: 46%

Threaded rod allows periodic adjustments where gasketing and material tolerances may vary. Passivated zinc plated steel with yellow vinyl grip.

Latches - Adjustable Draw - With Keeper - Stainless

Search Rating: 46%

Threaded rod allows periodic adjustments where gasketing and material tolerances may vary. Passivated 300 Grade Stainless Steel.

Latches - Adjustable Draw - With Keeper - Steel

Search Rating: 46%

Threaded rod allows periodic adjustments where gasketing and material tolerances may vary. Passivated zinc plated Steel.

Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends

Search Rating: 46%

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 316 Grade - DIN7

Diameter tolerances are m6.

Washers - Flat - High Tensile

Search Rating: 46%

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Grade 8 high tensile washers

ASTM F436 1985. Please note! Tolerances for commercial grade washers are much larger than for precision washers.

Shafting - Pipe - Aluminium

Search Rating: 46%

Also see combined categories:
All Pipe Shaft
All Metal Tube

Recommended for use with Igubal Drylin bearings only.

Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: Ph Greater than 2 and Less than 9.

Strip - Spring Steel

Search Rating: 46%

Also see combined categories:
All Metal Strip

Hundreds of uses.

Hardened and tempered spring steel strip. Note that the width of this strip may vary minus nothing to plus 25 percent as it is guillotine cut from sheet. If you require a closer tolerance on the strip width please contact us prior to ordering.

Balls - Ceramic - Ruby - Synthetic

Search Rating: 46%

Also see combined categories:
All Ceramic Balls
All Non Metallic Balls

Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.

Tolerances available on request. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Specific Gravity: 3.98.

Bushes - Plastic - Iglidur Q - Flanged

Search Rating: 46%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Excellent wear resistance under high load. Resistant to dirt.

Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 ^oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerances is E10 after H7 Pressfit. Tolerances listed in the tables take this into account.

Bushes - Plastic - Iglidur Q - Unflanged

Search Rating: 46%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Excellent wear resistance under high load. Resistant to dirt.

Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 ^oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerances is E10 after H7 Pressfit. Tolerances listed in the tables take this into account.

Shafting - Unground - Silver Steel

Search Rating: 46%

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

Unhardened silversteel shafting for general purposes. Not suitable for precision bearings until machined to correct tolerances and hardened.

See also drill rod. Drill Rod.

Balls - Ceramic - Sapphire - Synthetic

Search Rating: 46%

Also see combined categories:
All Ceramic Balls
All Non Metallic Balls

Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.

Tolerances available on request. Specific Gravity: 3.98. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Transparent (refractive index 1.76).

Balls - Plastic - Acetal

Search Rating: 46%

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

High intensity strength, rigidity, outstanding resistance to abrasion and most solvents.

Tolerances available on request. Acetal Copolymer. High intensity strength, rigidity, outstanding resistance to abrasion and most solvents. Opaque White. Specific Gravity: 1.4.

Bushes - Aluminium Bronze - Flanged

Search Rating: 46%

Also see combined categories:
All Bronze Bushes
All Flanged Bronze Bushes

Used for dies, moulds and heavy machinery. C95400 Aluminium bronze.

ID and OD Tolerance : -0.0000 / +0.0127. Length Tolerance : -1.524 / +0.000.

Bushes - Aluminium Bronze - Unflanged

Search Rating: 46%

Also see combined categories:
All Bronze Bushes
All Unflanged Bronze Bushes

Used for dies, moulds and heavy machinery. C95400 Aluminium bronze.

ID and OD Tolerance : -0.0000 / +0.0127. Length Tolerance : -1.524 / +0.000.

Bushes - Plastic - Iglidur F - Flanged

Search Rating: 46%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.

Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 ^oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerances is D11 after H7 Pressfit. Tolerances listed in the tables take this into account.

Bushes - Plastic - Iglidur F - Unflanged

Search Rating: 46%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.

Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 ^oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerances is D11 after H7 Pressfit. Tolerances listed in the tables take this into account.

Bushes - Plastic - Iglidur W300 - Flanged

Search Rating: 46%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 ^oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerances is E10 after H7 Pressfit. Tolerances listed in the tables take this into account.

Bushes - Plastic - Iglidur W300 - Unflanged

Search Rating: 46%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 ^oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerances is E10 after H7 Pressfit. Tolerances listed in the tables take this into account.

Bushes - Plastic - Iglidur Z - Flanged

Search Rating: 46%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

High temperature. High thermal resistance. Extreme load. High surface speed.

Specific Gravity 1.40 g/cm3. Operating Temp 310 C short term / 250 C long term. Tensile Strength at 20 ^oC = 95 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerances is F10 after H7 Pressfit. Tolerances listed in the tables take this into account.

Bushes - Plastic - Iglidur Z - Unflanged

Search Rating: 46%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

High temperature. High thermal resistance. Extreme load. High surface speed.

Specific Gravity 1.40 g/cm3. Operating Temp 310 C short term / 250 C long term. Tensile Strength at 20 ^oC = 95 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerances is F10 after H7 Pressfit. Tolerances listed in the tables take this into account.

Washers - Disc Spring - Plastic

Search Rating: 46%

Also see combined categories:
All Disc Springs

Also known as belleville washers.

Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb^(R) material.

Bushes - Plastic - Iglidur H370 - Flanged

Search Rating: 45%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.

Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 ^oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerances is F10 after H7 Pressfit. Tolerances listed in the tables take this into account.

Bushes - Plastic - Iglidur H370 - Unflanged

Search Rating: 45%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.

Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 ^oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerances is F10 after H7 Pressfit. Tolerances listed in the tables take this into account.

Balls - Stainless Steel - 304 Grade

Search Rating: 45%

Also see combined categories:
All Metallic Balls

A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.

Tolerances available on request. Grade 100. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000 ^oC.