Miniature Bearings Australia Pty Ltd

Searched For: Stroke Rotary Bushings Categories


Stroke Rotary Bushings


Bushings - Stroke Rotary - Miniature
Bushings - Stroke Rotary - Miniature

Also see combined categories:
All Stroke Rotary Bushings

2 to 12mm Shaft Sizes. Can operate in both linear and rotary directions at the same time.

Set includes outer ring, ball cage and shaft. Ball Cage: Brass Balls: Hard Steel / Shaft: Hard Steel Outer Ring: Hard Steel. Temperature: +100oC (Constant), +120oC (Maximum). Stroke: = (L1 - Lb) x 2. Supplied with extreme accuracy with zero to minimum preload.

Related Information:

There is also a good range of Bushings - Stroke Rotary - Miniature on the Small Parts and Bearings website.


Bushings - Snap - Closed
Bushings - Snap - Closed


Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Open snap bushings are designed to provide protection from sharp edges where cable or hose runs through plate steel.

Similar to a bung, but designed with expanding catch for use in holes in sheet products. Also see grommets for a similar product made from rubber. This category may be available in the new MBA online store at Bushings - Snap - Closed.

Related Information:

There is also a good range of Bushings - Snap - Closed on the Small Parts and Bearings website.


Bushings - Snap - Open
Bushings - Snap - Open


Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Closed snap bushings are designed to keep out dust and other contaminants and protect from sharp edges where cable or hose used to run through a hole in plate steel.

Also called a dome plug. Also see grommets for a similar product made from rubber. This category may be available in the new MBA online store at Bushings - Snap - Open.

Related Information:

There is also a good range of Bushings - Snap - Open on the Small Parts and Bearings website.


Pins - Dowel Bushings
Pins - Dowel Bushings

Also see combined categories:
All Dowel Bushings

Series DB100 Spirol

Spring Steel. Precision rolled bushes manufactured from spring steel. Designed to eliminate the need for separate dowling where two components are to be located accurately together and fastened with bolts. They are available for use with bolts from M5 to M12. This category may be available in the new MBA online store at Pins - Dowel Bushings.

Related Information:

There is also a good range of Pins - Dowel Bushings on the Small Parts and Bearings website.


Bushings - QD
Bushings - QD


Used with QD type cast iron vee pulleys, timing pulleys, sprockets, poly vee pulleys and other parts designed specifically for use with a QD bushing

Similar to a taperlock bush, but not interchangeable. QD bushings like taperlock bushings allow for use of a single stock pulley for many applications with different shaft sizes. Select the correct QD series to suit the pulley. This category may be available in the new MBA online store at Bushings - QD.

Related Information:

There is also a good range of Bushings - QD on the Small Parts and Bearings website.


Bushings - Taperlock
Bushings - Taperlock


This category may be available in the new MBA online store at Bushings - Taperlock.

There is also a good range of Bushings - Taperlock on the Small Parts and Bearings website.


Bushings - Spherical - Plastic
Bushings - Spherical - Plastic

Also see combined categories:
All Spherical Bushings

Plastic spherical plain bearings. Also known as ball bushings.

Ball Material W300. Housing Iglidur G. Maintenance Free. Self lubricating. Compensates for axial loads and misalignment. Corrosion resistant. High vibration dampening capacity.

There is also a good range of Bushings - Spherical - Plastic on the Small Parts and Bearings website.


Bushings - Spherical - Steel
Bushings - Spherical - Steel

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment. This category may be available in the new MBA online store at Bushings - Spherical - Steel.

There is also a good range of Bushings - Spherical - Steel on the Small Parts and Bearings website.


Bushings - Spherical - Steel - With Oil Hole
Bushings - Spherical - Steel - With Oil Hole

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment. This category may be available in the new MBA online store at Bushings - Spherical - Steel - With Oil Hole.

There is also a good range of Bushings - Spherical - Steel - With Oil Hole on the Small Parts and Bearings website.


Bushings - Spherical - Steel - With Oil Hole and Wiper Seal
Bushings - Spherical - Steel - With Oil Hole and Wiper Seal

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment. This category may be available in the new MBA online store at Bushings - Spherical - Steel - With Oil Hole and Wiper Seal.

There is also a good range of Bushings - Spherical - Steel - With Oil Hole and Wiper Seal on the Small Parts and Bearings website.


Bushings - Spherical - Steel - With Wiper Seal
Bushings - Spherical - Steel - With Wiper Seal

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment. This category may be available in the new MBA online store at Bushings - Spherical - Steel - With Wiper Seal.

There is also a good range of Bushings - Spherical - Steel - With Wiper Seal on the Small Parts and Bearings website.


Bushings - Integral Taper
Bushings - Integral Taper

Also see combined categories:
All Locking Assemblies
All Locking Bushings

Stainless Steel Taper Bushings.

Will not mar shafts. This category may be available in the new MBA online store at Bushings - Integral Taper.

There is also a good range of Bushings - Integral Taper on the Small Parts and Bearings website.


Bushings - Drill - Liner Type - Headless
Bushings - Drill - Liner Type - Headless

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point. Hardness: RC 62-64. This category may be available in the new MBA online store at Bushings - Drill - Liner Type - Headless.

There is also a good range of Bushings - Drill - Liner Type - Headless on the Small Parts and Bearings website.


Bushings - Drill - Press-fit - Headless
Bushings - Drill - Press-fit - Headless

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Hardness: RC 62-64. This category may be available in the new MBA online store at Bushings - Drill - Press-fit - Headless.

There is also a good range of Bushings - Drill - Press-fit - Headless on the Small Parts and Bearings website.


Bushings - Drill - Press-fit - Headless - Tungsten Carbide
Bushings - Drill - Press-fit - Headless - Tungsten Carbide

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point. Hardness: RC 67-69. This category may be available in the new MBA online store at Bushings - Drill - Press-fit - Headless - Tungsten Carbide.

There is also a good range of Bushings - Drill - Press-fit - Headless - Tungsten Carbide on the Small Parts and Bearings website.


Bushings - Drill - Press-fit - Standard Head
Bushings - Drill - Press-fit - Standard Head

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Hardness: RC 62-64. This category may be available in the new MBA online store at Bushings - Drill - Press-fit - Standard Head.

There is also a good range of Bushings - Drill - Press-fit - Standard Head on the Small Parts and Bearings website.


Bushings - Drill - Slip - With Head
Bushings - Drill - Slip - With Head

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point. Hardness: RC 62-64. This category may be available in the new MBA online store at Bushings - Drill - Slip - With Head.

There is also a good range of Bushings - Drill - Slip - With Head on the Small Parts and Bearings website.


Bushings - Tension
Bushings - Tension


Like a heavy duty roll pin.

Made of a high carbon spring steel with high elasticity, resilience and wear characteristics. Designed to replace solid steel tubular and case hardened bushings because they are close tolerance, self-retaining and through hard. Insertion can be easily accomplished with a hammer and drift. Ideal for high load/low-speed operation in articulating or continuous applications. This category may be available in the new MBA online store at Bushings - Tension.

There is also a good range of Bushings - Tension on the Small Parts and Bearings website.


Bushings - Shoulder
Bushings - Shoulder


This category may be available in the new MBA online store at Bushings - Shoulder.

There is also a good range of Bushings - Shoulder on the Small Parts and Bearings website.


Mounts - Bonded - Tee Bushing - Centre Bolt
Mounts - Bonded - Tee Bushing - Centre Bolt


Vibration isolation for mobile and static applications involving plate clamping

Reduces structure borne noise and absorbs shock forces. Low profile height. This category may be available in the new MBA online store at Mounts - Bonded - Tee Bushing - Centre Bolt.

Related Information:

There is also a good range of Mounts - Bonded - Tee Bushing - Centre Bolt on the Small Parts and Bearings website.


Spacers - Machinery Bushings
Spacers - Machinery Bushings

Also see combined categories:
All Round Spacers
All Flat Washers and Spacers - Metallic

Used as spacers between pulleys, gears etc

Low carbon mild steel. This category may be available in the new MBA online store at Spacers - Machinery Bushings.

There is also a good range of Spacers - Machinery Bushings on the Small Parts and Bearings website.


Dual Vee - Adaptor Bushings
Dual Vee - Adaptor Bushings


Vee grooved track roller bushings.

Stationary bushings have a concentric hole. Adjustable bushings have an eccentric hole allowing positioning of the guide wheel as the bush is turned. This category may be available in the new MBA online store at Dual Vee - Adaptor Bushings.

Related Information:

There is also a good range of Dual Vee - Adaptor Bushings on the Small Parts and Bearings website.


Cam Followers - Self Lubricating - Bronze Bushing
Cam Followers - Self Lubricating - Bronze Bushing

Also see combined categories:
All Cam Followers

This category may be available in the new MBA online store at Cam Followers - Self Lubricating - Bronze Bushing.


Elements - Locking
Elements - Locking

Also see combined categories:
All Locking Assemblies

2.4 to 2200 Nm, 6-80mm Bores

ETG 100 High Strength Steel for sizes up to 55mm bore. C60 Steel for sizes over 55mm bore. Recommended machining tolerances Shaft h8, Hub H8. This category may be available in the new MBA online store at Elements - Locking.

There is also a good range of Elements - Locking on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur G - Flanged
Bushes - Plastic - Iglidur G - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur G - Flanged on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur G - Unflanged
Bushes - Plastic - Iglidur G - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur G - Unflanged on the Small Parts and Bearings website.


Pulleys - Vee - A - 4L - Single Row - For QD Bushing
Pulleys - Vee - A - 4L - Single Row - For QD Bushing

Also see combined categories:
All Vee Pulleys A Section 12.5 and 12.7mm Top Width

Cast iron pulleys. QD bushings are used to vary the bore sizes.

This category may be available in the new MBA online store at Pulleys - Vee - A - 4L - Single Row - For QD Bushing.

Related Information:

There is also a good range of Pulleys - Vee - A - 4L - Single Row - For QD Bushing on the Small Parts and Bearings website.


Pulleys - Vee - B - 5L - Single Row - For QD Bushing
Pulleys - Vee - B - 5L - Single Row - For QD Bushing

Also see combined categories:
All Vee Pulleys B Section 15.9 and 16.5mm Top Width

Cast iron pulleys. QD bushings are used to vary the bore sizes.

This category may be available in the new MBA online store at Pulleys - Vee - B - 5L - Single Row - For QD Bushing.

Related Information:

There is also a good range of Pulleys - Vee - B - 5L - Single Row - For QD Bushing on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur M250 - Flanged
Bushes - Plastic - Iglidur M250 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur M250 - Flanged on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur M250 - Unflanged
Bushes - Plastic - Iglidur M250 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur M250 - Unflanged on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur J - Flanged
Bushes - Plastic - Iglidur J - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur J - Flanged on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur J - Unflanged
Bushes - Plastic - Iglidur J - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur J - Unflanged on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur Q - Flanged
Bushes - Plastic - Iglidur Q - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Excellent wear resistance under high load. Resistant to dirt.

Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur Q - Flanged on the Small Parts and Bearings website.


Ball Buttons
Ball Buttons


Also known as striker bushings or ball plunger detents. Use with ball or bolt spring plungers for a hard wearing contact area.

Burnished ground hardened steel. This category may be available in the new MBA online store at Ball Buttons.

There is also a good range of Ball Buttons on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur F - Unflanged
Bushes - Plastic - Iglidur F - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.

Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur F - Unflanged on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur W300 - Flanged
Bushes - Plastic - Iglidur W300 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur W300 - Flanged on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur W300 - Unflanged
Bushes - Plastic - Iglidur W300 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur W300 - Unflanged on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur H370 - Unflanged
Bushes - Plastic - Iglidur H370 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.

Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur H370 - Unflanged on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur A200 - Flanged
Bushes - Plastic - Iglidur A200 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur A200 - Flanged on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur A200 - Unflanged
Bushes - Plastic - Iglidur A200 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur A200 - Unflanged on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur A290 - Unflanged
Bushes - Plastic - Iglidur A290 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 250 Mpa. Hardness 88 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur A290 - Unflanged on the Small Parts and Bearings website.


Grommets - Rubber - EPDM
Grommets - Rubber - EPDM

Also see combined categories:
All Open Rubber Grommets
All Rubber Grommets

EPDM Rubber Grommets

50 +/-5 Durometer. Easy to install. Good Vibration and Shock Control. Protects Wire, Cable and Hoses. Also see snap bushings for a hard plastic product serving a similar purpose.

Related Information:

There is also a good range of Grommets - Rubber - EPDM on the Small Parts and Bearings website.


Grommets - Rubber - Natural
Grommets - Rubber - Natural

Also see combined categories:
All Open Rubber Grommets
All Rubber Grommets

Natural Rubber Grommets

50 +/-5 Durometer. Easy to Install. Good Vibration and Shock Control. Protects Wire, Cable and Hoses. Also see snap bushings for a hard plastic product serving a similar purpose.

Related Information:

There is also a good range of Grommets - Rubber - Natural on the Small Parts and Bearings website.


Grommets - Rubber - EPDM - Closed
Grommets - Rubber - EPDM - Closed

Also see combined categories:
All Closed Rubber Grommets
All Rubber Grommets

Closed EPDM Rubber Grommets

50 +/-5 Durometer. Dustproof with Approx 0.5mm thick Membrane. Easy to Install. Dust protection. Also see snap bushings for a hard plastic product serving a similar purpose.

Related Information:

There is also a good range of Grommets - Rubber - EPDM - Closed on the Small Parts and Bearings website.


Catches - Rotary
Catches - Rotary


Polyacetal catch and strike with polyethylene rollers. Ideal in corrosive environments.

This category may be available in the new MBA online store at Catches - Rotary.

There is also a good range of Catches - Rotary on the Small Parts and Bearings website.


Tools - Rotary Files - Aluminium Cut
Tools - Rotary Files - Aluminium Cut

Also see combined categories:
All Tools

Used for deburring and smoothing metals.

Made from Heat treated steel. This category may be available in the new MBA online store at Tools - Rotary Files - Aluminium Cut.

There is also a good range of Tools - Rotary Files - Aluminium Cut on the Small Parts and Bearings website.


Tools - Rotary Files - Double Cut
Tools - Rotary Files - Double Cut

Also see combined categories:
All Tools

Used for deburring and smoothing metals.

Made from Heat treated steel. This category may be available in the new MBA online store at Tools - Rotary Files - Double Cut.

There is also a good range of Tools - Rotary Files - Double Cut on the Small Parts and Bearings website.


Tools - Rotary Files - Standard Cut
Tools - Rotary Files - Standard Cut

Also see combined categories:
All Tools

Used for deburring and smoothing metals.

Made from Heat treated steel. This category may be available in the new MBA online store at Tools - Rotary Files - Standard Cut.

There is also a good range of Tools - Rotary Files - Standard Cut on the Small Parts and Bearings website.


Dampers - Rotary - 2.0 to 3.0 Ncm
Dampers - Rotary -  2.0 to 3.0 Ncm

Also see combined categories:
All Dampers

Rotary dampers enable products to function with a smooth mechanical motion. Prevent lid and access panel closure damage.

Body: Polycarbonate / Gear: Polyacetal. Fluid: Silicone. Temp range 0 to 50 oC. This category may be available in the new MBA online store at Dampers - Rotary - 2.0 to 3.0 Ncm.

There is also a good range of Dampers - Rotary - 2.0 to 3.0 Ncm on the Small Parts and Bearings website.


Dampers - Rotary - 5.0 to 15.0 Ncm
Dampers - Rotary -  5.0 to 15.0 Ncm

Also see combined categories:
All Dampers

Rotary dampers enable products to function with a smooth mechanical motion. Prevent lid and access panel closure damage.

Body: Polycarbonate / Gear: Polyacetal. Fluid: Silicone. Temp range 0 to 50 oC. This category may be available in the new MBA online store at Dampers - Rotary - 5.0 to 15.0 Ncm.

There is also a good range of Dampers - Rotary - 5.0 to 15.0 Ncm on the Small Parts and Bearings website.





Main Pages

5 Axis Machine Tool Bearings About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Distributor Locations Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Satellite Reaction Wheels Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 219038 products in 2167 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 219038 products in 2167 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.