Stroke Rotary Bushings Categories
Bushings - Stroke Rotary - Miniature
2 to 12mm Shaft Sizes. Can operate in both linear and rotary directions at the same time.
Set includes outer ring, ball cage and shaft. Ball Cage: Brass Balls: Hard Steel / Shaft: Hard Steel Outer Ring: Hard Steel. Temperature: +100oC (Constant), +120oC (Maximum). Stroke: = (L1 - Lb) x 2. Supplied with extreme accuracy with zero to minimum preload.
Related Information:
There is also a good range of Bushings - Stroke Rotary - Miniature on the Small Parts and Bearings website.
Bushings - Snap - Closed
Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Open snap bushings are designed to provide protection from sharp edges where cable or hose runs through plate steel.
Similar to a bung, but designed with expanding catch for use in holes in sheet products. Also see grommets for a similar product made from rubber.
Related Information:
There is also a good range of Bushings - Snap - Closed on the Small Parts and Bearings website.
Bushings - Snap - Open
Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Closed snap bushings are designed to keep out dust and other contaminants and protect from sharp edges where cable or hose used to run through a hole in plate steel.
Also called a dome plug. Also see grommets for a similar product made from rubber.
Related Information:
There is also a good range of Bushings - Snap - Open on the Small Parts and Bearings website.
Pins - Dowel Bushings
Series DB100 Spirol
Spring Steel. Precision rolled bushes manufactured from spring steel. Designed to eliminate the need for separate dowling where two components are to be located accurately together and fastened with bolts. They are available for use with bolts from M5 to M12.
Related Information:
There is also a good range of Pins - Dowel Bushings on the Small Parts and Bearings website.
Bushings - QD
Used with QD type cast iron vee pulleys, timing pulleys, sprockets, poly vee pulleys and other parts designed specifically for use with a QD bushing
Similar to a taperlock bush, but not interchangeable. QD bushings like taperlock bushings allow for use of a single stock pulley for many applications with different shaft sizes. Select the correct QD series to suit the pulley.
There is also a good range of Bushings - QD on the Small Parts and Bearings website.
Bushings - Taperlock
There is also a good range of Bushings - Taperlock on the Small Parts and Bearings website.
Bushings - Spherical - Plastic
Plastic spherical plain bearings. Also known as ball bushings.
Ball Material W300. Housing Iglidur G. Maintenance Free. Self lubricating. Compensates for axial loads and misalignment. Corrosion resistant. High vibration dampening capacity.
There is also a good range of Bushings - Spherical - Plastic on the Small Parts and Bearings website.
Bushings - Spherical - Steel
Steel spherical plain bearings. Also known as ball bushings.
Compensates for axial loads and misalignment.
There is also a good range of Bushings - Spherical - Steel on the Small Parts and Bearings website.
Bushings - Spherical - Steel - With Oil Hole
Steel spherical plain bearings. Also known as ball bushings.
Compensates for axial loads and misalignment.
There is also a good range of Bushings - Spherical - Steel - With Oil Hole on the Small Parts and Bearings website.
Bushings - Spherical - Steel - With Oil Hole and Wiper Seal
Steel spherical plain bearings. Also known as ball bushings.
Compensates for axial loads and misalignment.
There is also a good range of Bushings - Spherical - Steel - With Oil Hole and Wiper Seal on the Small Parts and Bearings website.
Bushings - Spherical - Steel - With Wiper Seal
Steel spherical plain bearings. Also known as ball bushings.
Compensates for axial loads and misalignment.
There is also a good range of Bushings - Spherical - Steel - With Wiper Seal on the Small Parts and Bearings website.
Bushings - Drill - Liner Type - Headless
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.
There is also a good range of Bushings - Drill - Liner Type - Headless on the Small Parts and Bearings website.
Bushings - Drill - Press-fit - Headless
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
There is also a good range of Bushings - Drill - Press-fit - Headless on the Small Parts and Bearings website.
Bushings - Drill - Press-fit - Headless - Tungsten Carbide
Designed to guide, position, and support the cutting tool in a metalworking jig.
Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.
There is also a good range of Bushings - Drill - Press-fit - Headless - Tungsten Carbide on the Small Parts and Bearings website.
Bushings - Drill - Press-fit - Standard Head
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
There is also a good range of Bushings - Drill - Press-fit - Standard Head on the Small Parts and Bearings website.
Bushings - Drill - Slip - With Head
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.
There is also a good range of Bushings - Drill - Slip - With Head on the Small Parts and Bearings website.
Bushings - Tension
Like a heavy duty roll pin.
Made of a high carbon spring steel with high elasticity, resilience and wear characteristics. Designed to replace solid steel tubular and case hardened bushings because they are close tolerance, self-retaining and through hard. Insertion can be easily accomplished with a hammer and drift. Ideal for high load/low-speed operation in articulating or continuous applications.
There is also a good range of Bushings - Tension on the Small Parts and Bearings website.
Bushings - Shoulder
Mould components
There is also a good range of Bushings - Shoulder on the Small Parts and Bearings website.
Dual Vee - Adaptor Bushings
Vee grooved track roller bushings.
Stationary bushings have a concentric hole. Adjustable bushings have an eccentric hole allowing positioning of the guide wheel as the bush is turned.
Related Information:
There is also a good range of Dual Vee - Adaptor Bushings on the Small Parts and Bearings website.
Spacers - Machinery Bushings
Used as spacers between pulleys, gears etc
Low carbon mild steel.
There is also a good range of Spacers - Machinery Bushings on the Small Parts and Bearings website.
Cam Followers - Self Lubricating - Bronze Bushing
There is also a good range of Cam Followers - Self Lubricating - Bronze Bushing on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur G - Flanged
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur G - Flanged on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur G - Unflanged
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur G - Unflanged on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur H - Flanged
Underwater performance. High Temp. Chemical Resistance.
Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 175 Mpa. Hardness 87 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur H - Flanged on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur H - Unflanged
Underwater performance. High Temp. Chemical Resistance.
Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 175 Mpa. Hardness 87 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur H - Unflanged on the Small Parts and Bearings website.
Pulleys - Vee - A - 4L - Single Row - For QD Bushing
Cast iron pulleys. QD bushings are used to vary the bore sizes.
Related Information:
There is also a good range of Pulleys - Vee - A - 4L - Single Row - For QD Bushing on the Small Parts and Bearings website.
Pulleys - Vee - B - 5L - Single Row - For QD Bushing
Cast iron pulleys. QD bushings are used to vary the bore sizes.
Related Information:
There is also a good range of Pulleys - Vee - B - 5L - Single Row - For QD Bushing on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur M250 - Flanged
For impact resistance vibration dampening unclean environments.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur M250 - Flanged on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur M250 - Unflanged
For impact resistance vibration dampening unclean environments.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur M250 - Unflanged on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur P - Flanged
Low water absorption. Low wear. Hgh load.
Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur P - Flanged on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur P - Unflanged
Low water absorption. Low wear. Hgh load.
Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur P - Unflanged on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur J - Flanged
Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.
Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur J - Flanged on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur J - Unflanged
Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.
Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur J - Unflanged on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur Q - Flanged
Excellent wear resistance under high load. Resistant to dirt.
Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur Q - Flanged on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur Q - Unflanged
Excellent wear resistance under high load. Resistant to dirt.
Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur Q - Unflanged on the Small Parts and Bearings website.
Ball Buttons
Also known as striker bushings or ball plunger detents. Use with ball or bolt spring plungers for a hard wearing contact area.
Burnished ground hardened steel.
There is also a good range of Ball Buttons on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur F - Flanged
Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.
Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur F - Flanged on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur F - Unflanged
Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.
Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur F - Unflanged on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur W300 - Flanged
Low co-efficient of friction. High wear resistance. Chemical resistant.
Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur W300 - Flanged on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur W300 - Unflanged
Low co-efficient of friction. High wear resistance. Chemical resistant.
Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur W300 - Unflanged on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur Z - Flanged
High temperature. High thermal resistance. Extreme load. High surface speed.
Specific Gravity 1.40 g/cm3. Operating Temp 310 C short term / 250 C long term. Tensile Strength at 20 oC = 95 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur Z - Flanged on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur Z - Unflanged
High temperature. High thermal resistance. Extreme load. High surface speed.
Specific Gravity 1.40 g/cm3. Operating Temp 310 C short term / 250 C long term. Tensile Strength at 20 oC = 95 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur Z - Unflanged on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur H370 - Flanged
Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.
Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur H370 - Flanged on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur H370 - Unflanged
Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.
Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur H370 - Unflanged on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur A200 - Flanged
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur A200 - Flanged on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur A200 - Unflanged
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur A200 - Unflanged on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur A290 - Flanged
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 250 Mpa. Hardness 88 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur A290 - Flanged on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur A290 - Unflanged
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 250 Mpa. Hardness 88 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur A290 - Unflanged on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur X - Flanged
Very high temperature. Extreme chemical resistance. High compressive strength. Low water absorption.
Specific Gravity 1.44 g/cm3. Operating Temp 315 C short term / 250 C long term. Tensile Strength at 20 oC = 170 Mpa. Hardness 85 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur X - Flanged on the Small Parts and Bearings website.
Bushes - Plastic - Iglidur X - Unflanged
Very high temperature. Extreme chemical resistance. High compressive strength. Low water absorption.
Specific Gravity 1.44 g/cm3. Operating Temp 315 C short term / 250 C long term. Tensile Strength at 20 oC = 170 Mpa. Hardness 85 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
There is also a good range of Bushes - Plastic - Iglidur X - Unflanged on the Small Parts and Bearings website.
Main Pages
About Us
Balls
Bearings
Brands
Catalogue
Clearance Items
Contact Us
Dental Bearings
Distributor Locations
Dowel Pins
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)
Miniature Bearings Australia offers 122538 products in 2633 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.
Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.
