SHAFTLOC CATEGORIES
Shaftloc-tm Sleeves - Single Ended
Simple effective way to lock components onto shafts.
416 Stainless Steel. Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened. This category may be available in the new MBA online store at Shaftloc-tm Sleeves - Single Ended.
Related Information:
There is also a good range of Shaftloc-tm Sleeves - Single Ended on the Small Parts and Bearings website.
Pulleys - Timing - 3.000mm Pitch - HTD - 9mm Wide - Plastic - Hubless
Timing Pulleys to suit HTD 3.000mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide. Moulded single or double flange. No hub.
Suitable for use with shaftloc sleeves.
Related Information:
There is also a good range of Pulleys - Timing - 3.000mm Pitch - HTD - 9mm Wide - Plastic - Hubless on the Small Parts and Bearings website.
Collars - Shaft - Gripfast - 304 Stainless Steel
Self Locking - Quick Release.
304 Stainless Body, Retention Ring, Balls and Springs. This category may be available in the new MBA online store at Collars - Shaft - Gripfast - 304 Stainless Steel.
Related Information:
There is also a good range of Collars - Shaft - Gripfast - 304 Stainless Steel on the Small Parts and Bearings website.
Collars - Shaft - Gripfast - ABS Plastic
Self Locking - Quick Release.
265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs. This category may be available in the new MBA online store at Collars - Shaft - Gripfast - ABS Plastic.
Related Information:
There is also a good range of Collars - Shaft - Gripfast - ABS Plastic on the Small Parts and Bearings website.
Assemblies - Locking - Flanged
Suitable for locking sprockets, pulleys, eccentric shafts.
Locks components with a bore of (D) to shafts with a diameter of (d). C60 Steel (060A62). Outer ring expands whilst inner ring contracts. Flange eliminates axial movement of secured component. During tightening of the screws, the hub must be able to perform axial movement. Clearance h8 / H8. Surface roughness Rt max 10um shaft / hub.
There is also a good range of Assemblies - Locking - Flanged on the Small Parts and Bearings website.
Bushings - Integral Taper
Stainless Steel Taper Bushings.
Will not mar shafts. This category may be available in the new MBA online store at Bushings - Integral Taper.
There is also a good range of Bushings - Integral Taper on the Small Parts and Bearings website.
Socket Set Screws - Acetal Tipped - Alloy Steel
Acetal tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
This category may be available in the new MBA online store at Socket Set Screws - Acetal Tipped - Alloy Steel.
Related Information:
There is also a good range of Socket Set Screws - Acetal Tipped - Alloy Steel on the Small Parts and Bearings website.
Socket Set Screws - Acetal Tipped - Stainless Steel
Acetal tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
This category may be available in the new MBA online store at Socket Set Screws - Acetal Tipped - Stainless Steel.
Related Information:
There is also a good range of Socket Set Screws - Acetal Tipped - Stainless Steel on the Small Parts and Bearings website.
Socket Set Screws - Nylon Tipped - Alloy Steel
Nylon tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
This category may be available in the new MBA online store at Socket Set Screws - Nylon Tipped - Alloy Steel.
Related Information:
There is also a good range of Socket Set Screws - Nylon Tipped - Alloy Steel on the Small Parts and Bearings website.
Elements - Locking
2.4 to 2200 Nm, 6-80mm Bores
ETG 100 High Strength Steel for sizes up to 55mm bore. C60 Steel for sizes over 55mm bore. Recommended machining tolerances Shaft h8, Hub H8. This category may be available in the new MBA online store at Elements - Locking.
There is also a good range of Elements - Locking on the Small Parts and Bearings website.
Socket Set Screws - Nylon Tipped - 304 Stainless Steel
Nylon tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
This category may be available in the new MBA online store at Socket Set Screws - Nylon Tipped - 304 Stainless Steel.
Related Information:
There is also a good range of Socket Set Screws - Nylon Tipped - 304 Stainless Steel on the Small Parts and Bearings website.
Shafting - Ground - Hobby - Steel
Silversteel shafting for hobbies. Not suitable for precision bearings.
Suitable for use with plastic gears, bushes, couplings etc. Not recommended for use with precision steel or stainless steel bearings. Some sizes have special features such as serrations or small barbs (noted in description). Unground ends. Ideal for axles in robotic applications and educational projects.
Related Information:
Shafting - Linear - Square
This category may be available in the new MBA online store at Shafting - Linear - Square.
There is also a good range of Shafting - Linear - Square on the Small Parts and Bearings website.
Motors - DC 6mm Diameter
Our smallest motors at an affordable price.
Various models 10000 to 30000 rpm. Low starting voltage of Less than0.8V. Rated Voltage 1.3V. Less than 43 dB Mechanical Noise Level. 100 hours / 100000 turns mechanical life. Clockwise rotation when viewed from shaft end. Not recommended for reversing.
Related Information:
There is also a good range of Motors - DC 6mm Diameter on the Small Parts and Bearings website.
Shafts - Flexible - Coupling Ends - Open - Mild Steel
Flexible shafting with coupling ends ready to attach to a fixed shaft.
1.7 and 2.5mm cable diameters can be operated manually at 62mm bend radius with torsional break strength of 0.62 N.m. 3.3F shaft has a greater degree of flexibility than standard 3.3mm. 3.3F shaft can be used in dynamic mode if shaft isshortened to approximately 50mm. This category may be available in the new MBA online store at Shafts - Flexible - Coupling Ends - Open - Mild Steel.
Related Information:
There is also a good range of Shafts - Flexible - Coupling Ends - Open - Mild Steel on the Small Parts and Bearings website.
Shafting - Aluminium - Ceramic Coated
Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.
Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated. This category may be available in the new MBA online store at Shafting - Aluminium - Ceramic Coated.
Related Information:
There is also a good range of Shafting - Aluminium - Ceramic Coated on the Small Parts and Bearings website.
Shafting - Aluminium - Ceramic Coated - Tapped
Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.
Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated. This category may be available in the new MBA online store at Shafting - Aluminium - Ceramic Coated - Tapped.
Related Information:
There is also a good range of Shafting - Aluminium - Ceramic Coated - Tapped on the Small Parts and Bearings website.
Shafting - Carbon Steel - Keyed
Keyways are cut full length of each bar. Low carbon steel C1018. Good case hardening properties.
Diameter Tolerance +0.00/-0.051. Keyway Depth Tolerance +0.41/-0.00. Keyway Width Tolerance +0.05/-0.00. Unhardened carbon steel. Special order may be available for stainless steel, other diameters, other lengths. Please ask.
There is also a good range of Shafting - Carbon Steel - Keyed on the Small Parts and Bearings website.
Shafting - Mild Steel
Great axles for low load and low precision applications like trolleys, carts and wheelbarrows.
Check listed specifications for keyway information. This category may be available in the new MBA online store at Shafting - Mild Steel.
Related Information:
Shafts - Flexible - Panel Mount - Cased
This category may be available in the new MBA online store at Shafts - Flexible - Panel Mount - Cased.
There is also a good range of Shafts - Flexible - Panel Mount - Cased on the Small Parts and Bearings website.
Shafts - Flexible - Panel Mount - Open
This category may be available in the new MBA online store at Shafts - Flexible - Panel Mount - Open.
There is also a good range of Shafts - Flexible - Panel Mount - Open on the Small Parts and Bearings website.
Shafting - Ground - Precision - Chrome Plated
Precision ground shafting. AISI C1060 and chrome plated for corrosion resistance. Case hardened and recommended for use with precision bearings. Ends are not plated.
Case hardened to 60-65 Rockwell C. Chrome plated for corrosion resistance. This category may be available in the new MBA online store at Shafting - Ground - Precision - Chrome Plated.
There is also a good range of Shafting - Ground - Precision - Chrome Plated on the Small Parts and Bearings website.
Shafting - Ground - Precision - High Carbon Steel
Precision ground shafting. AISI C1060. Hardened and recommended for use with precision bearings.
This category may be available in the new MBA online store at Shafting - Ground - Precision - High Carbon Steel.
Related Information:
There is also a good range of Shafting - Ground - Precision - High Carbon Steel on the Small Parts and Bearings website.
Shafting - Ground - Precision - Stainless 303 Grade
Precision ground shafting.
This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 303 Grade.
Related Information:
There is also a good range of Shafting - Ground - Precision - Stainless 303 Grade on the Small Parts and Bearings website.
Shafting - Ground - Precision - Stainless 416 Grade Hardened
Precision ground shafting. 416 grade. Hardened and recommended for use with precision bearings.
This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 416 Grade Hardened.
Related Information:
There is also a good range of Shafting - Ground - Precision - Stainless 416 Grade Hardened on the Small Parts and Bearings website.
Shafting - Ground - Precision - Stainless 420 Grade Hardened
Precision ground shafting. 420 grade. Hardened and recommended for use with precision bearings.
This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 420 Grade Hardened.
Related Information:
There is also a good range of Shafting - Ground - Precision - Stainless 420 Grade Hardened on the Small Parts and Bearings website.
Shafting - Ground - Precision - Stainless 440C Grade Hardened
Precision ground shafting. 440C grade. Hardened and recommended for use with precision bearings.
This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 440C Grade Hardened.
Related Information:
There is also a good range of Shafting - Ground - Precision - Stainless 440C Grade Hardened on the Small Parts and Bearings website.
Shafting - Ground - Precision - Titanium - High Strength
Titanium shafting available in oversized and undersized tolerances
Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5, 6Al-4V, TC4 is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent. Shaft with undersized tolerances is suitable for use with precision ground bearings wih inner rings. HRC 36. Surface Finish Ra 0.8-1.6 um. Not suitable for running needle bearings directly. Shaft with oversized tolerances is suitable for pulleys or gears requiring interference fits, or for machining to your required tolerances.
Related Information:
There is also a good range of Shafting - Ground - Precision - Titanium - High Strength on the Small Parts and Bearings website.
Shafting - Ground - Precision - Titanium - Ti-Gr2-TA1
CP2 Commercially Pure Titanium Grade 2. Tensile Strength 35.2 kgf/mm2. Yield Strength 28.2 kgf/mm2. Elongation 20 Percent.
Commercially pure for general industrial corrosion applications. UNS R50400. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.3, O 0.25, Ti Balance. Shaft with undersized tolerances is suitable for use with precision ground bearings with inner rings. HRB 74. Surface Finish Ra 0.8-1.6 um. Not suitable for running needle bearings directly. Shaft with oversized tolerances is suitable for pulleys or gears requiring interference fits, or for machining to your required tolerances.
Related Information:
There is also a good range of Shafting - Ground - Precision - Titanium - Ti-Gr2-TA1 on the Small Parts and Bearings website.
Shafting - Pre Drilled and Tapped - Stainless Steel
For use with rail supports and open linear bearings
This category may be available in the new MBA online store at Shafting - Pre Drilled and Tapped - Stainless Steel.
There is also a good range of Shafting - Pre Drilled and Tapped - Stainless Steel on the Small Parts and Bearings website.
Shafts - Idler
Ready made precision ground idler shafts.
Internal grease hole can be accessed by drilling if required. Use with your idler pulleys. Can be used with the idler tensioners listed on this site or use in your own design. This category may be available in the new MBA online store at Shafts - Idler.
Related Information:
There is also a good range of Shafts - Idler on the Small Parts and Bearings website.
Shafts - Pinion
This category may be available in the new MBA online store at Shafts - Pinion.
There is also a good range of Shafts - Pinion on the Small Parts and Bearings website.
Rollers - Durasoft - Shaft Mount - Black Neoprene
Used on conveyors, belt idlers, shock cushioners, stamping die part guides, supports etc.
Designed for use in machines and assembly operations where part movement and protection is needed. Durasoft rollers have a gentle but firm touch. Unique shape of holes adds to their soft but resilient nature. This category may be available in the new MBA online store at Rollers - Durasoft - Shaft Mount - Black Neoprene.
There is also a good range of Rollers - Durasoft - Shaft Mount - Black Neoprene on the Small Parts and Bearings website.
Rollers - Durasoft - Shaft Mount - Coloured Urethane
Used on conveyors, belt idlers, shock cushioners, stamping die part guides, supports etc.
Designed for use in machines and assembly operations where part movement and protection is needed. Durasoft rollers have a gentle but firm touch. Unique shape of holes adds to their soft but resilient nature. Blue colour may turn a shade of green when exposed to UV lighting. This category may be available in the new MBA online store at Rollers - Durasoft - Shaft Mount - Coloured Urethane.
There is also a good range of Rollers - Durasoft - Shaft Mount - Coloured Urethane on the Small Parts and Bearings website.
Rollers - Durasoft - Shaft Mount - With Ball Bearing
Used on conveyors, belt idlers, shock cushioners, stamping die part guides, supports etc.
Designed for use in machines and assembly operations where part movement and protection is needed. Durasoft rollers have a gentle but firm touch. Unique shape of holes adds to their soft but resilient nature. Blue colour may turn a shade of green when exposed to UV lighting. This category may be available in the new MBA online store at Rollers - Durasoft - Shaft Mount - With Ball Bearing.
There is also a good range of Rollers - Durasoft - Shaft Mount - With Ball Bearing on the Small Parts and Bearings website.
Rollers - Solid - Shaft Mount - Black Neoprene
Used on conveyors, belt idlers, shock cushioners, stamping die part guides, supports etc.
Designed for use in machines and assembly operations where part movement and protection is needed. This category may be available in the new MBA online store at Rollers - Solid - Shaft Mount - Black Neoprene.
There is also a good range of Rollers - Solid - Shaft Mount - Black Neoprene on the Small Parts and Bearings website.
Rollers - Solid - Shaft Mount - Coloured Urethane
Used on conveyors, belt idlers, shock cushioners, stamping die part guides, supports etc.
Designed for use in machines and assembly operations where part movement and protection is needed. Blue colour may turn a shade of green when exposed to UV lighting. This category may be available in the new MBA online store at Rollers - Solid - Shaft Mount - Coloured Urethane.
There is also a good range of Rollers - Solid - Shaft Mount - Coloured Urethane on the Small Parts and Bearings website.
Collars - Shaft - Clamp Type - One Piece - Aluminium
This category may be available in the new MBA online store at Collars - Shaft - Clamp Type - One Piece - Aluminium.
Related Information:
There is also a good range of Collars - Shaft - Clamp Type - One Piece - Aluminium on the Small Parts and Bearings website.
Collars - Shaft - Clamp Type - One Piece - Stainless Steel
This category may be available in the new MBA online store at Collars - Shaft - Clamp Type - One Piece - Stainless Steel.
Related Information:
There is also a good range of Collars - Shaft - Clamp Type - One Piece - Stainless Steel on the Small Parts and Bearings website.
Collars - Shaft - Clamp Type - One Piece - Steel
This category may be available in the new MBA online store at Collars - Shaft - Clamp Type - One Piece - Steel.
Related Information:
There is also a good range of Collars - Shaft - Clamp Type - One Piece - Steel on the Small Parts and Bearings website.
Collars - Shaft - Clamp Type - Two Piece - 300 Grade Stainless Steel
Includes 303 and 304 Grade Stainless
Related Information:
There is also a good range of Collars - Shaft - Clamp Type - Two Piece - 300 Grade Stainless Steel on the Small Parts and Bearings website.
Collars - Shaft - Clamp Type - Two Piece - Aluminium
This category may be available in the new MBA online store at Collars - Shaft - Clamp Type - Two Piece - Aluminium.
Related Information:
There is also a good range of Collars - Shaft - Clamp Type - Two Piece - Aluminium on the Small Parts and Bearings website.
Collars - Shaft - Clamp Type - Two Piece - Steel
This category may be available in the new MBA online store at Collars - Shaft - Clamp Type - Two Piece - Steel.
Related Information:
There is also a good range of Collars - Shaft - Clamp Type - Two Piece - Steel on the Small Parts and Bearings website.
Collars - Shaft - Hex Bore - One Piece - 303 Stainless Steel
This category may be available in the new MBA online store at Collars - Shaft - Hex Bore - One Piece - 303 Stainless Steel.
Related Information:
There is also a good range of Collars - Shaft - Hex Bore - One Piece - 303 Stainless Steel on the Small Parts and Bearings website.
Collars - Shaft - Hex Bore - One Piece - Steel
This category may be available in the new MBA online store at Collars - Shaft - Hex Bore - One Piece - Steel.
Related Information:
There is also a good range of Collars - Shaft - Hex Bore - One Piece - Steel on the Small Parts and Bearings website.
Collars - Shaft - Hex Bore - Two Piece - 303 Stainless Steel
This category may be available in the new MBA online store at Collars - Shaft - Hex Bore - Two Piece - 303 Stainless Steel.
Related Information:
There is also a good range of Collars - Shaft - Hex Bore - Two Piece - 303 Stainless Steel on the Small Parts and Bearings website.
Collars - Shaft - Hex Bore - Two Piece - Steel
This category may be available in the new MBA online store at Collars - Shaft - Hex Bore - Two Piece - Steel.
Related Information:
There is also a good range of Collars - Shaft - Hex Bore - Two Piece - Steel on the Small Parts and Bearings website.
Collars - Shaft - Hinged - Stainless Steel
Precision machined. Convenient easy-to-assemble design. 303 Stainless Steel
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Related Information:
There is also a good range of Collars - Shaft - Hinged - Stainless Steel on the Small Parts and Bearings website.
Collars - Shaft - Hinged - Steel
Precision machined. Convenient easy-to-assemble design. Steel 12L14 (9SMn Pb36)
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Related Information:
There is also a good range of Collars - Shaft - Hinged - Steel on the Small Parts and Bearings website.
Collars - Shaft - Standard - Nylon
Standard one piece nylon shaft collar with set screw
Static torque and axial load are for reference only using steel cup point grub screw on soft steel shaft. This category may be available in the new MBA online store at Collars - Shaft - Standard - Nylon.
Related Information:
There is also a good range of Collars - Shaft - Standard - Nylon on the Small Parts and Bearings website.
Main Pages
5 Axis Machine Tool Bearings
About Us
Acetal Bearings PDF
ADR and SKF PDF
Anderton Circlips Cross Reference PDF
Ball Lock Pins PDF
Balls List
Balls PDF
Barden Bearings Cross Reference PDF
Bearings List
Brands
Catalogue
Ceramic Bearings PDF
Circlips PDF
Clearance Items List
Clevis Pins PDF
Contact Us
Charity
Corrosion Resistant Bearings PDF
Dental Bearings
Disc Springs PDF
Distributor Locations
Dowel Pins PDF
Dowel Pins
Economy Bearings PDF
Essentra Cross Reference PDF
Flocast Cross Reference PDF
Freight Rates and Shipping Times
Frequently Asked Questions
General Information about MBA
Hammer Drive Pins PDF
High Speed Bearings PDF
Hobby Clearance
Hobby Information
K&S Metals Cross Reference PDF
Key Steel PDF
Knobs PDF
Large Bearings
Leveling Mounts PDF
Mailorder Form
McMaster Carr Cross Reference PDF
Metallic Bushes PDF
Miniature Precison Bearings Cross Reference PDF
Nordex Cross Reference PDF
NSK and NTN Cross Reference PDF
Ondrives Cross Reference PDF
O-Rings PDF
Pins PDF
Plastic Bearings PDF
Polyvee Belts and Pulleys PDF
Precision Shim Washers PDF
Privacy
Push On and Push In Rings PDF
Reid Supply Cross Reference PDF
Rod & Tube PDF
Roll Pins PDF
Satellite Reaction Wheels
SDP-SI Designatronics Cross Reference PDF
Seeger Circlips Cross Reference PDF
Shaft Collars PDF
Shim Sheet PDF
Shoulder Screws PDF
Sintered Bronze Bushes PDF
Sintered Bronze Cross Reference PDF
Small Bearings
Small Parts Inc Cross Reference PDF
Snap Rings PDF
Socket Set Screws PDF
Solid Bronze Bushes PDF
Spring Steel Strip PDF
Springs PDF
Standard Ball Bearing Range PDF
Super Precision Bearings PDF
Taper Pins PDF
Technical Information
Terms
Thrust Bearings PDF
Thumb Screws and Nuts PDF
Timing Belts and Pulleys Cross Reference PDF
Timing Belts PDF
Timing Pulley Stock PDF
Timing Pulleys PDF
Vibration Mounts PDF
Washers and Spacers PDF
Wave Washers PDF
Domains
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)
Miniature Bearings Australia offers 209441 products in 2115 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.
