Shafting Aluminium Categories
Shafting - Aluminium
Drylin aluminium shafting is recommended for use with Igubal Drylin bearings or Frelon lined bearings only.
Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: ph between 2 and 9.
There is also a good range of Shafting - Aluminium on the Small Parts and Bearings website.
Shafting - Aluminium - Ceramic Coated
Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.
Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated.
Related Information:
There is also a good range of Shafting - Aluminium - Ceramic Coated on the Small Parts and Bearings website.
Shafting - Aluminium - Ceramic Coated - Tapped
Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.
Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated.
Related Information:
There is also a good range of Shafting - Aluminium - Ceramic Coated - Tapped on the Small Parts and Bearings website.
Shafting - Pipe - Aluminium
Recommended for use with Igubal Drylin bearings only.
Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: Ph Greater than 2 and Less than 9.
There is also a good range of Shafting - Pipe - Aluminium on the Small Parts and Bearings website.
Shafting - Supported - Pre-Drilled - Aluminium
For Drylin Bearings.
Material : AlMgSi 0.5 F22. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Spec. Electr. Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: Ph Greater than 2 and less than 9.
There is also a good range of Shafting - Supported - Pre-Drilled - Aluminium on the Small Parts and Bearings website.
You may also be interested in
Shafting Precision Ground
Supports - Pedestal Two Bolt
For linear shafting.
Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel.
Related Information:
There is also a good range of Supports - Pedestal Two Bolt on the Small Parts and Bearings website.
Rail Supports - With Shaft - One Piece
One piece construction made from 6061-T6 Aluminium with ceramic coating to Mil-8625. Suitable for use with Frelon lined linear bearings.
Not suitable for linear ball bearings. Weld spatter, paints and other contaminants will not stick to the shaft. Vibration resistant and non-magnetic. Not suitable for harsh washdown environments.
Related Information:
There is also a good range of Rail Supports - With Shaft - One Piece on the Small Parts and Bearings website.
Rail Supports - Without Shaft
For mounting of linear shafting.
Shafting sold separately. Support is made from aluminium.
Related Information:
There is also a good range of Rail Supports - Without Shaft on the Small Parts and Bearings website.
Rail Supports - With Shaft
Includes linear shafting.
Includes shaft to h6 tolerances. Support is made from aluminium.
Related Information:
There is also a good range of Rail Supports - With Shaft on the Small Parts and Bearings website.
Engineering and Hobby Rod
Rod - Round - Aluminium
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground.
Related Information:
There is also a good range of Rod - Round - Aluminium on the Small Parts and Bearings website.
Tube and Tubing
Tube - Round - Aluminium
Hollow round tubing for general hobby applications.
For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Many sizes fit neatly into larger sizes to allow for telescoping size applications. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
Related Information:
There is also a good range of Tube - Round - Aluminium on the Small Parts and Bearings website.
Tube - Round - Soft Metal Packs
For general hobby applications. This tube is annealed soft to make it easier to bend. Copper, brass and aluminium,
300mm lengths. Not recommended for heavy duty applications. For use with bearings we suggest you use items from the category - Shafting - Ground.
There is also a good range of Tube - Round - Soft Metal Packs on the Small Parts and Bearings website.
Engineering and Hobby Rod
Rod - Round - Soft Metal Packs
For general hobby applications. This rod is annealed soft to make it easier to bend. Copper, brass and aluminium,
300mm lengths. Not recommended for heavy duty applications. For use with bearings we suggest you use items from the category - Shafting - Ground.
There is also a good range of Rod - Round - Soft Metal Packs on the Small Parts and Bearings website.
Enclosures - Aluminium - Economy
Great little boxes ready for you to adapt to your mechanical projects.
Excellent screening properties for EMI and RFI. Ideal for projects subject to weather. Great housings for mechanical projects. Easy to machine. 380 Die Cast aluminium alloy BS1490 LM24. Close fitting flanged lids.
There is also a good range of Enclosures - Aluminium - Economy on the Small Parts and Bearings website.
Rectangular Bar - Aluminium
Thin and thick Aluminum strip and rectangular profiles
Small sizes may not be perfectly straight.
There is also a good range of Rectangular Bar - Aluminium on the Small Parts and Bearings website.
Screws - Thumb - Knurled - Aluminium
Aluminum knurled head thumb screws
There is also a good range of Screws - Thumb - Knurled - Aluminium on the Small Parts and Bearings website.
Snaps - Swivel Eye - Aluminium
Rust proof nickel plated made from finest quality zinc aluminium alloy
There is also a good range of Snaps - Swivel Eye - Aluminium on the Small Parts and Bearings website.
Couplings - Double Disk - Aluminium
Zero Backlash - High Torsional Stiffness.
Hub and Spacer: Aluminium Alloy. Pin and Disc: Stainless Steel. Max Axial Play: +/-0.5mm. 0.7 to 12.5 Nm. 3000 to 19000 rpm.
Related Information:
There is also a good range of Couplings - Double Disk - Aluminium on the Small Parts and Bearings website.
Rollers - Feed - With Aluminium Sleeve
Tolerance of Roller Outside Diameter (D) is +/-0.075 mm
Urethane 60 Durometer ground outside diameter. Aluminium sleeve. Feed rollers do not have a rotating bore. They are designed to turn with the shaft.
Related Information:
There is also a good range of Rollers - Feed - With Aluminium Sleeve on the Small Parts and Bearings website.
Spacers - Round - Through Bore - Aluminium
Shaft spacers - Aluminium
There is also a good range of Spacers - Round - Through Bore - Aluminium on the Small Parts and Bearings website.
Bushes - Aluminium Bronze - Flanged
Used for dies, moulds and heavy machinery. C95400 Aluminium bronze.
ID and OD Tolerance : -0.0000 / +0.0127. Length Tolerance : -1.524 / +0.000.
Related Information:
There is also a good range of Bushes - Aluminium Bronze - Flanged on the Small Parts and Bearings website.
Bushes - Aluminium Bronze - Graphite Plug - Flanged
Used for dies, moulds and heavy machinery. C95400 Aluminium bronze.
ID and OD Tolerance : -0.0000 / +0.0127. Length Tolerance : -1.524 / +0.000.
Related Information:
There is also a good range of Bushes - Aluminium Bronze - Graphite Plug - Flanged on the Small Parts and Bearings website.
Bushes - Aluminium Bronze - Graphite Plug - Unflanged
Used for dies, moulds and heavy machinery. C95400 Aluminium bronze.
ID and OD Tolerance : -0.0000 / +0.0127. Length Tolerance : -1.524 / +0.000.
Related Information:
There is also a good range of Bushes - Aluminium Bronze - Graphite Plug - Unflanged on the Small Parts and Bearings website.
Bushes - Aluminium Bronze - Unflanged
Used for dies, moulds and heavy machinery. C95400 Aluminium bronze.
ID and OD Tolerance : -0.0000 / +0.0127. Length Tolerance : -1.524 / +0.000.
Related Information:
There is also a good range of Bushes - Aluminium Bronze - Unflanged on the Small Parts and Bearings website.
Enclosures - Aluminium - 100 Series
Great little boxes ready for you to adapt to your mechanical or electrical projects.
Internal guide slots for mounting PCB assemblies vertically. Ideal for housing sensitive electrical, mechanical, pneumatic or hydraulic devices. Provides effective shielding of EMI and RFI. Designed to IP65 of IEC529 and NEMA 4 (dust and hoseproof). The lid incorporates a recessed neoprene gasket.
There is also a good range of Enclosures - Aluminium - 100 Series on the Small Parts and Bearings website.
Sheet - Aluminium - T1100
Non precision inexpensive aluminium sheet for hobby applications. Heat-treated T1100 grade.
Sheet for applications not requiring absolute precision. Thickness tolerances +/- 0.1mm. Lengths and widths will be at least that specified but may be more.
There is also a good range of Sheet - Aluminium - T1100 on the Small Parts and Bearings website.
Sheet - Aluminium - T7075
Non precision inexpensive aluminium sheet for hobby applications. Heat-treated T7075 grade.
Sheet for applications not requiring absolute precision. Thickness tolerances +/- 0.1mm. Lengths and widths will be at least that specified but may be more.
There is also a good range of Sheet - Aluminium - T7075 on the Small Parts and Bearings website.
Inserts - Self Tapping - For Aluminium - Steel
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.
Related Information:
There is also a good range of Inserts - Self Tapping - For Aluminium - Steel on the Small Parts and Bearings website.
Gears - Spur - 120DP - Aluminium
PCD = No. of Teeth x 0.212mm (1/120 in.). 20o Pressure Angle. 2024 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.
Metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 120 Diametrical Pitch. Approx 0.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.
Related Information:
There is also a good range of Gears - Spur - 120DP - Aluminium on the Small Parts and Bearings website.
Gears - Spur - 80DP - Aluminium
PCD = No. of Teeth x 0.318mm (1/80 in.). 20o Pressure Angle. 2024 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.
Metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 80 Diametrical Pitch. Approx 1mm between teeth. For easy ready selected sets of rack and gear please see the HES website.
Related Information:
There is also a good range of Gears - Spur - 80DP - Aluminium on the Small Parts and Bearings website.
Gears - Spur - 96DP - Aluminium
PCD = No. of Teeth x 0.265mm (1/96 in.). 20o Pressure Angle. 2024 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.
Metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 96 Diametrical Pitch. Approx 0.83mm between teeth. For easy ready selected sets of rack and gear please see the HES website.
Related Information:
There is also a good range of Gears - Spur - 96DP - Aluminium on the Small Parts and Bearings website.
Inserts - Self Tapping - For Aluminium - Stainless 303
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.
Related Information:
There is also a good range of Inserts - Self Tapping - For Aluminium - Stainless 303 on the Small Parts and Bearings website.
Gears - Spur - 64DP - Aluminium
PCD = No. of Teeth x 0.397mm (1/64 in.). 20o Pressure Angle. 5052 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.
Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 64 Diametrical Pitch. Approx 1.25mm between teeth. For easy ready selected sets of rack and gear please see the HES website.
Related Information:
There is also a good range of Gears - Spur - 64DP - Aluminium on the Small Parts and Bearings website.
Gears - Spur - 72DP - Aluminium
PCD = No. of Teeth x 0.353mm (1/72 in.). 20o Pressure Angle. 2024 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.
Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 72 Diametrical Pitch. Approx 1.11mm between teeth. For easy ready selected sets of rack and gear please see the HES website.
Related Information:
There is also a good range of Gears - Spur - 72DP - Aluminium on the Small Parts and Bearings website.
Screws - Thumb - Knurled - Washer Face - Aluminium
Knurled head aluminum thumb screws with an integral washer
There is also a good range of Screws - Thumb - Knurled - Washer Face - Aluminium on the Small Parts and Bearings website.
Gears - Internal - 24 Diametrical Pitch - Aluminium
2024-T4 Aluminum
There is also a good range of Gears - Internal - 24 Diametrical Pitch - Aluminium on the Small Parts and Bearings website.
Gears - Internal - 32 Diametrical Pitch - Aluminium
2024-T4 Aluminum
There is also a good range of Gears - Internal - 32 Diametrical Pitch - Aluminium on the Small Parts and Bearings website.
Gears - Internal - 48 Diametrical Pitch - Aluminium
2024-T4 Aluminum
There is also a good range of Gears - Internal - 48 Diametrical Pitch - Aluminium on the Small Parts and Bearings website.
Gears - Internal - 64 Diametrical Pitch - Aluminium
2024-T4 Aluminum
There is also a good range of Gears - Internal - 64 Diametrical Pitch - Aluminium on the Small Parts and Bearings website.
Gears - Internal - 72 Diametrical Pitch - Aluminium
2024-T4 Aluminum
There is also a good range of Gears - Internal - 72 Diametrical Pitch - Aluminium on the Small Parts and Bearings website.
Gears - Internal - 96 Diametrical Pitch - Aluminium
2024-T4 Aluminum
There is also a good range of Gears - Internal - 96 Diametrical Pitch - Aluminium on the Small Parts and Bearings website.
Gears - Spur - Module 0.5 - Aluminium
PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. 2024 aluminium
Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.
Related Information:
There is also a good range of Gears - Spur - Module 0.5 - Aluminium on the Small Parts and Bearings website.
Gears - Spur - Module 0.8 - Aluminium
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 2024 aluminium
Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.
Related Information:
There is also a good range of Gears - Spur - Module 0.8 - Aluminium on the Small Parts and Bearings website.
Gears - Spur - Module 1 - Aluminium
PCD = No. of Teeth x 1.000mm. 20o Pressure Angle. 2024 aluminium.
Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.
Related Information:
There is also a good range of Gears - Spur - Module 1 - Aluminium on the Small Parts and Bearings website.
Washers - Flat - Aluminium
Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Flat washers.
Related Information:
There is also a good range of Washers - Flat - Aluminium on the Small Parts and Bearings website.
Tube - Square - Aluminium
Hollow square tubing for general hobby applications.
Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
Related Information:
There is also a good range of Tube - Square - Aluminium on the Small Parts and Bearings website.
Tube - Streamline - Aluminium
Streamline Aluminium Tubing.
Teardrop shaped soft aluminium tubing. Enables easier bending. Great for tight applications.
Related Information:
There is also a good range of Tube - Streamline - Aluminium on the Small Parts and Bearings website.
Collars - Shaft - Clamp Type - One Piece - Aluminium
Related Information:
There is also a good range of Collars - Shaft - Clamp Type - One Piece - Aluminium on the Small Parts and Bearings website.
Collars - Shaft - Clamp Type - Two Piece - Aluminium
Related Information:
There is also a good range of Collars - Shaft - Clamp Type - Two Piece - Aluminium on the Small Parts and Bearings website.
Linear Slides - Utilitrak - PW - Crowned - Channel - Aluminium
Use with Utilitrak PW Crowned Carriages. 6063-T6 aluminium alloy. Economical choice for light duty applications.
Related Information:
There is also a good range of Linear Slides - Utilitrak - PW - Crowned - Channel - Aluminium on the Small Parts and Bearings website.
Main Pages
About Us
Balls
Bearings
Brands
Catalogue
Clearance Items
Contact Us
Dental Bearings
Distributor Locations
Dowel Pins
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)
Miniature Bearings Australia offers 122538 products in 2633 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.
Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.
