Miniature Bearings Australia Pty Ltd

Searched For: SETS CATEGORIES


Sets


Tools - Sets
Tools - Sets

Also see combined categories:
All Tools

General tool sets, screwdriver sets, tap sets, dies sets, hex key sets.

This category may be available in the new MBA online store at Tools - Sets.

There is also a good range of Tools - Sets on the Small Parts and Bearings website.


Tools - Sets - Foldup
Tools - Sets - Foldup

Also see combined categories:
All Tools

Handy sets of popular sized hex and torx wrenches.

Highest quality 8650 chrome nickel alloy heat treated and finished to resist rust. Ergo style has colour coded handles. Classic style has one piece steel grip handle. Conveniently folds up like a jack knife when not in use. This category may be available in the new MBA online store at Tools - Sets - Foldup.

There is also a good range of Tools - Sets - Foldup on the Small Parts and Bearings website.


Inserts - Thread Repair - Recoil Starter Sets
Inserts - Thread Repair - Recoil Starter Sets

Also see combined categories:
All Recoil Inserts and Kits

Recoil inserts are screwed directly into an enlarged tapped hole. A tap and installation tool is included with these kits.

Stainless inserts. Contents: Ground intermediate (2nd) tap. Inserts. Installation/tang break off tool. Full instructions. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.

There is also a good range of Inserts - Thread Repair - Recoil Starter Sets on the Small Parts and Bearings website.


Inserts - Thread Repair - Keylocking Starter Sets
Inserts - Thread Repair - Keylocking Starter Sets

Also see combined categories:
All Keylocking Inserts and Kits

Keylocking inserts are used to repair threads by tapping the worn thread to a standard larger thread, twisting the insert into place and then driving in the keys to lock the insert. Also known as keenserts.

Each kit contains an installation tool and the quantity of inserts shown. One size per kit. Also known as keenserts, keylocking inserts are available in mild steel and stainless steel. Installation is by drilling out the old thread, countersinking, tapping new thread with a standard tap, screwing the insert until slightly below the surface, then tapping down the keys using the tool supplied and a hammer. This category may be available in the new MBA online store at Inserts - Thread Repair - Keylocking Starter Sets.

Related Information:

There is also a good range of Inserts - Thread Repair - Keylocking Starter Sets on the Small Parts and Bearings website.


Slotted Set Screws - Partial Thread
Slotted Set Screws - Partial Thread

Also see combined categories:
All Special Hard Tip Grub Screws
All Dog Point Grub Screws

Partially threaded metric slotted drive set screws - grub screws

This category may be available in the new MBA online store at Slotted Set Screws - Partial Thread.

Related Information:

There is also a good range of Slotted Set Screws - Partial Thread on the Small Parts and Bearings website.


Socket Set Screws - Acetal Tipped - Alloy Steel
Socket Set Screws - Acetal Tipped - Alloy Steel

Also see combined categories:
All Soft Tipped Grub Screws
All Grub Screws

Acetal tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.

This category may be available in the new MBA online store at Socket Set Screws - Acetal Tipped - Alloy Steel.

Related Information:

There is also a good range of Socket Set Screws - Acetal Tipped - Alloy Steel on the Small Parts and Bearings website.


Socket Set Screws - Acetal Tipped - Stainless Steel
Socket Set Screws - Acetal Tipped - Stainless Steel

Also see combined categories:
All Soft Tipped Grub Screws
All Grub Screws

Acetal tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.

This category may be available in the new MBA online store at Socket Set Screws - Acetal Tipped - Stainless Steel.

Related Information:

There is also a good range of Socket Set Screws - Acetal Tipped - Stainless Steel on the Small Parts and Bearings website.


Socket Set Screws - Brass Tipped - Alloy Steel
Socket Set Screws - Brass Tipped - Alloy Steel

Also see combined categories:
All Soft Tipped Grub Screws
All Grub Screws

Brass tipped grub screws. Helps to prevent shaft damage on harder shafts.

This category may be available in the new MBA online store at Socket Set Screws - Brass Tipped - Alloy Steel.

Related Information:

There is also a good range of Socket Set Screws - Brass Tipped - Alloy Steel on the Small Parts and Bearings website.


Socket Set Screws - Brass Tipped - Stainless Steel
Socket Set Screws - Brass Tipped - Stainless Steel

Also see combined categories:
All Soft Tipped Grub Screws
All Grub Screws

Brass tipped grub screws. Helps to prevent shaft damage on harder shafts.

This category may be available in the new MBA online store at Socket Set Screws - Brass Tipped - Stainless Steel.

Related Information:

There is also a good range of Socket Set Screws - Brass Tipped - Stainless Steel on the Small Parts and Bearings website.


Socket Set Screws - Cone Point
Socket Set Screws - Cone Point

Also see combined categories:
All Special Hard Tip Grub Screws
All Grub Screws

Cone point grub screws

This category may be available in the new MBA online store at Socket Set Screws - Cone Point.

Related Information:

There is also a good range of Socket Set Screws - Cone Point on the Small Parts and Bearings website.


Socket Set Screws - Cup Point - Standard - 304 Stainless Steel - DIN916
Socket Set Screws - Cup Point - Standard - 304 Stainless Steel - DIN916

Also see combined categories:
All Cup Point Standard Grub Screws
All Grub Screws

Standard grub screws. UNC - UNF - BA - METRIC.


Related Information:

There is also a good range of Socket Set Screws - Cup Point - Standard - 304 Stainless Steel - DIN916 on the Small Parts and Bearings website.


Socket Set Screws - Cup Point - Standard - 316 Stainless Steel - DIN916
Socket Set Screws - Cup Point - Standard - 316 Stainless Steel - DIN916

Also see combined categories:
All Cup Point Standard Grub Screws
All Grub Screws

Standard grub screws. UNC - UNF - BA - METRIC.


Related Information:

There is also a good range of Socket Set Screws - Cup Point - Standard - 316 Stainless Steel - DIN916 on the Small Parts and Bearings website.


Socket Set Screws - Cup Point - Standard - Alloy Steel - DIN916
Socket Set Screws - Cup Point - Standard - Alloy Steel - DIN916

Also see combined categories:
All Cup Point Standard Grub Screws
All Grub Screws

Standard grub screws. UNC - UNF - BA - METRIC.

This category may be available in the new MBA online store at Socket Set Screws - Cup Point - Standard - Alloy Steel - DIN916.

Related Information:

There is also a good range of Socket Set Screws - Cup Point - Standard - Alloy Steel - DIN916 on the Small Parts and Bearings website.


Socket Set Screws - Cup Point - Standard - Zinc Plated - DIN916
Socket Set Screws - Cup Point - Standard - Zinc Plated - DIN916

Also see combined categories:
All Cup Point Standard Grub Screws
All Grub Screws

Standard grub screws. UNC - UNF - BA - METRIC.

This category may be available in the new MBA online store at Socket Set Screws - Cup Point - Standard - Zinc Plated - DIN916.

Related Information:

There is also a good range of Socket Set Screws - Cup Point - Standard - Zinc Plated - DIN916 on the Small Parts and Bearings website.


Socket Set Screws - Cup Point - Titanium - CP Grade 1 - DIN916
Socket Set Screws - Cup Point - Titanium - CP Grade 1 - DIN916

Also see combined categories:
All Non Magnetic Grub Screws
All Grub Screws

Standard DIN913 grub screws. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.

Commercially pure for general industrial corrosion applications. UNS R50250. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance. This category may be available in the new MBA online store at Socket Set Screws - Cup Point - Titanium - CP Grade 1 - DIN916.

Related Information:

There is also a good range of Socket Set Screws - Cup Point - Titanium - CP Grade 1 - DIN916 on the Small Parts and Bearings website.


Socket Set Screws - Cup Point - Titanium - Ti-Gr5 - Ti-6Al4v - DIN916
Socket Set Screws - Cup Point - Titanium - Ti-Gr5 - Ti-6Al4v - DIN916

Also see combined categories:
All Non Magnetic Grub Screws
All Grub Screws

Standard DIN916 grub screws with cup point. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Related Information:

There is also a good range of Socket Set Screws - Cup Point - Titanium - Ti-Gr5 - Ti-6Al4v - DIN916 on the Small Parts and Bearings website.


Socket Set Screws - Diamond Knurled Tip - Stainless Steel
Socket Set Screws - Diamond Knurled Tip - Stainless Steel

Also see combined categories:
All Special Hard Tip Grub Screws
All Diamond Knurled Tip Grub Screws

Grub screws that grip rough shafts.

This category may be available in the new MBA online store at Socket Set Screws - Diamond Knurled Tip - Stainless Steel.

Related Information:

There is also a good range of Socket Set Screws - Diamond Knurled Tip - Stainless Steel on the Small Parts and Bearings website.


Socket Set Screws - Dog Point - Carbon Steel
Socket Set Screws - Dog Point - Carbon Steel

Also see combined categories:
All Special Hard Tip Grub Screws
All Dog Point Grub Screws

Dog point grub screws

This category may be available in the new MBA online store at Socket Set Screws - Dog Point - Carbon Steel.

Related Information:

There is also a good range of Socket Set Screws - Dog Point - Carbon Steel on the Small Parts and Bearings website.


Socket Set Screws - Flat Tip - Aligning - Carbon Steel
Socket Set Screws - Flat Tip - Aligning - Carbon Steel

Also see combined categories:
All Flat Aligning Tip Grub Screws
All Grub Screws

Grub screws with a pivoting flat tip. The ball can pivot up to 9 Deg. To fasten the object securely to misaligned parts.

Also known as a flat ball tip set screw or a clamping screw. This category may be available in the new MBA online store at Socket Set Screws - Flat Tip - Aligning - Carbon Steel.

Related Information:

There is also a good range of Socket Set Screws - Flat Tip - Aligning - Carbon Steel on the Small Parts and Bearings website.


Socket Set Screws - Flat Tip - Aligning - Stainless Steel
Socket Set Screws - Flat Tip - Aligning - Stainless Steel

Also see combined categories:
All Flat Aligning Tip Grub Screws
All Grub Screws

Grub screws with a pivoting flat tip. The ball can pivot up to 9 Deg. To fasten the object securely to misaligned parts.

Also known as a flat ball tip set screw or a clamping screw. This category may be available in the new MBA online store at Socket Set Screws - Flat Tip - Aligning - Stainless Steel.

Related Information:

There is also a good range of Socket Set Screws - Flat Tip - Aligning - Stainless Steel on the Small Parts and Bearings website.


Socket Set Screws - Flat Tip - Fixed - DIN913
Socket Set Screws - Flat Tip - Fixed - DIN913

Also see combined categories:
All Special Hard Tip Grub Screws
All Grub Screws

Flat tip grub screws

This category may be available in the new MBA online store at Socket Set Screws - Flat Tip - Fixed - DIN913.

Related Information:

There is also a good range of Socket Set Screws - Flat Tip - Fixed - DIN913 on the Small Parts and Bearings website.


Socket Set Screws - Flat Tip - Titanium - Ti-Gr5 - Ti-6Al4v - DIN913
Socket Set Screws - Flat Tip - Titanium - Ti-Gr5 - Ti-6Al4v - DIN913

Also see combined categories:
All Non Magnetic Grub Screws
All Grub Screws

Standard DIN913 grub screws with flat end. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Related Information:

There is also a good range of Socket Set Screws - Flat Tip - Titanium - Ti-Gr5 - Ti-6Al4v - DIN913 on the Small Parts and Bearings website.


Socket Set Screws - Half Dog Point
Socket Set Screws - Half Dog Point

Also see combined categories:
All Special Hard Tip Grub Screws
All Dog Point Grub Screws

Half Dog Point grub screws

This category may be available in the new MBA online store at Socket Set Screws - Half Dog Point.

Related Information:

There is also a good range of Socket Set Screws - Half Dog Point on the Small Parts and Bearings website.


Socket Set Screws - Magnetic End - Carbon Steel
Socket Set Screws - Magnetic End - Carbon Steel

Also see combined categories:
All Cup Point Standard Grub Screws
All Grub Screws

This category may be available in the new MBA online store at Socket Set Screws - Magnetic End - Carbon Steel.

Related Information:

There is also a good range of Socket Set Screws - Magnetic End - Carbon Steel on the Small Parts and Bearings website.


Socket Set Screws - Nylon Tipped - 304 Stainless Steel
Socket Set Screws - Nylon Tipped - 304 Stainless Steel

Also see combined categories:
All Soft Tipped Grub Screws
All Grub Screws

Nylon tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.

This category may be available in the new MBA online store at Socket Set Screws - Nylon Tipped - 304 Stainless Steel.

Related Information:

There is also a good range of Socket Set Screws - Nylon Tipped - 304 Stainless Steel on the Small Parts and Bearings website.


Socket Set Screws - Nylon Tipped - Alloy Steel
Socket Set Screws - Nylon Tipped - Alloy Steel

Also see combined categories:
All Soft Tipped Grub Screws
All Grub Screws

Nylon tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.

This category may be available in the new MBA online store at Socket Set Screws - Nylon Tipped - Alloy Steel.

Related Information:

There is also a good range of Socket Set Screws - Nylon Tipped - Alloy Steel on the Small Parts and Bearings website.


Socket Set Screws - Oval Tip - Alloy Steel
Socket Set Screws - Oval Tip - Alloy Steel

Also see combined categories:
All Special Hard Tip Grub Screws
All Grub Screws

This category may be available in the new MBA online store at Socket Set Screws - Oval Tip - Alloy Steel.

Related Information:

There is also a good range of Socket Set Screws - Oval Tip - Alloy Steel on the Small Parts and Bearings website.


Socket Set Screws - Rolling Ball Tip - Carbon Steel
Socket Set Screws - Rolling Ball Tip - Carbon Steel

Also see combined categories:
All Rolling Ball Tip Grub Screws
All Grub Screws

Rolling ball tip for locating into a hole

Rolling ball set screws are not designed to bear heavy loads. Used to lightly fasten fragile work pieces. We would recommend testing if you plan to use them in a load bearing application. This category may be available in the new MBA online store at Socket Set Screws - Rolling Ball Tip - Carbon Steel.

Related Information:

There is also a good range of Socket Set Screws - Rolling Ball Tip - Carbon Steel on the Small Parts and Bearings website.


Socket Set Screws - Rolling Ball Tip - Stainless Steel
Socket Set Screws - Rolling Ball Tip - Stainless Steel

Also see combined categories:
All Rolling Ball Tip Grub Screws
All Grub Screws

Rolling ball tip for locating into a hole

Rolling ball set screws are not designed to bear heavy loads. Used to lightly fasten fragile work pieces. We would recommend testing if you plan to use them in a load bearing application. This category may be available in the new MBA online store at Socket Set Screws - Rolling Ball Tip - Stainless Steel.

Related Information:

There is also a good range of Socket Set Screws - Rolling Ball Tip - Stainless Steel on the Small Parts and Bearings website.


Socket Set Screws - Solder Tipped - Stainless Steel
Socket Set Screws - Solder Tipped - Stainless Steel

Also see combined categories:
All Soft Tipped Grub Screws
All Grub Screws

Solder tipped grub screws. Allow fine adjustment and spreads over the contacting surface so as not to mark or deform it.

This category may be available in the new MBA online store at Socket Set Screws - Solder Tipped - Stainless Steel.

Related Information:

There is also a good range of Socket Set Screws - Solder Tipped - Stainless Steel on the Small Parts and Bearings website.


Socket Set Screws - Urethane Tipped - Alloy Steel
Socket Set Screws - Urethane Tipped - Alloy Steel

Also see combined categories:
All Rolling Ball Tip Grub Screws
All Grub Screws

Shore 70A Black Urethane tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.

This category may be available in the new MBA online store at Socket Set Screws - Urethane Tipped - Alloy Steel.

Related Information:

There is also a good range of Socket Set Screws - Urethane Tipped - Alloy Steel on the Small Parts and Bearings website.


Socket Set Screws - Urethane Tipped - Stainless Steel
Socket Set Screws - Urethane Tipped - Stainless Steel

Also see combined categories:
All Rolling Ball Tip Grub Screws
All Grub Screws

Shore 70A Black Urethane tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.

This category may be available in the new MBA online store at Socket Set Screws - Urethane Tipped - Stainless Steel.

Related Information:

There is also a good range of Socket Set Screws - Urethane Tipped - Stainless Steel on the Small Parts and Bearings website.


Screws - Set - Cup Point - Square Head
Screws - Set - Cup Point - Square Head


Grade 8 hreat treated alloy steel. All screws are threaded to the head.

This category may be available in the new MBA online store at Screws - Set - Cup Point - Square Head.

There is also a good range of Screws - Set - Cup Point - Square Head on the Small Parts and Bearings website.


Screws - Set - Dog Point - Square Head
Screws - Set - Dog Point - Square Head


Grade 8 hreat treated alloy steel. All screws are threaded to the head.

This category may be available in the new MBA online store at Screws - Set - Dog Point - Square Head.

There is also a good range of Screws - Set - Dog Point - Square Head on the Small Parts and Bearings website.


Couplings - Rigid - Set Screw
Couplings - Rigid - Set Screw

Also see combined categories:
All Rigid Couplings

0.35 to 5.1 Nm. Includes steel, stainless steel, brass and aluminium.

Quality Class Precision: Bore Tolerance +0.013 / - 0.000 concentric within 0.0127mm T.I.R. Quality Class Commercial: Bore Tolerance +0.051 / -0.000. This category may be available in the new MBA online store at Couplings - Rigid - Set Screw.

Related Information:

There is also a good range of Couplings - Rigid - Set Screw on the Small Parts and Bearings website.


Screws - Hex Head - Set - Titanium Ti-Gr5 - Ti-6Al4v
Screws - Hex Head - Set - Titanium Ti-Gr5 - Ti-6Al4v

Also see combined categories:
All Hex Head Screws

Fully threaded hex head set screws (DIN933). Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Used in critical aircraft structural components. UNS R56400. Din 933. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent. This category may be available in the new MBA online store at Screws - Hex Head - Set - Titanium Ti-Gr5 - Ti-6Al4v.

Related Information:

There is also a good range of Screws - Hex Head - Set - Titanium Ti-Gr5 - Ti-6Al4v on the Small Parts and Bearings website.


Washers - Self Aligning - Sets - Hardened Steel
Washers - Self Aligning - Sets - Hardened Steel

Also see combined categories:
All Thrust Washers
All Aligning Washers

Spherical Seat Washers

Hardened steel 9 S Mn Pb 28 K DIN 6319. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces. This category may be available in the new MBA online store at Washers - Self Aligning - Sets - Hardened Steel.

There is also a good range of Washers - Self Aligning - Sets - Hardened Steel on the Small Parts and Bearings website.


Washers - Self Aligning - Sets - Stainless Steel
Washers - Self Aligning - Sets - Stainless Steel

Also see combined categories:
All Thrust Washers
All Aligning Washers

Spherical Seat Washers

AISI 303 Stainless Steel. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces. This category may be available in the new MBA online store at Washers - Self Aligning - Sets - Stainless Steel.

There is also a good range of Washers - Self Aligning - Sets - Stainless Steel on the Small Parts and Bearings website.


Bearings - Tapered Roller - Single Row - Inch Sets
Bearings - Tapered Roller - Single Row - Inch Sets


Common automotive sets include cup and cone

This category may be available in the new MBA online store at Bearings - Tapered Roller - Single Row - Inch Sets.


Couplings - Reli-a-flex - Short Series - Set Screw Type
Couplings - Reli-a-flex - Short Series - Set Screw Type

Also see combined categories:
All Helical and Slit Couplings

From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).

Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.

Related Information:

There is also a good range of Couplings - Reli-a-flex - Short Series - Set Screw Type on the Small Parts and Bearings website.


Couplings - Slit Type - 4 Slit Miniature - Set Screw Type - Aluminium
Couplings - Slit Type - 4 Slit Miniature - Set Screw Type - Aluminium

Also see combined categories:
All Helical and Slit Couplings

Aluminium - Flexible.


There is also a good range of Couplings - Slit Type - 4 Slit Miniature - Set Screw Type - Aluminium on the Small Parts and Bearings website.


Couplings - Spiral Beam - 6 Beam - Aluminium - Set Screw Type
Couplings - Spiral Beam - 6 Beam - Aluminium - Set Screw Type

Also see combined categories:
All Helical and Slit Couplings

Pilot Bore size not toleranced. Finished Bore sizes to +0.03/0.00. This category may be available in the new MBA online store at Couplings - Spiral Beam - 6 Beam - Aluminium - Set Screw Type.

Related Information:

There is also a good range of Couplings - Spiral Beam - 6 Beam - Aluminium - Set Screw Type on the Small Parts and Bearings website.


Tools - Taps - High Speed Steel - Hand - Sets
Tools - Taps - High Speed Steel - Hand - Sets

Also see combined categories:
All Taps
All Tools

Metric and Imperial High Speed Steel tap sets including taper, intermediate and bottoming tap in each set

High Speed Steel (HSS) Short Machine taps. Older stock is Triangle Brand (UK). Newer stock is Volkel Brand (German). This category may be available in the new MBA online store at Tools - Taps - High Speed Steel - Hand - Sets.

There is also a good range of Tools - Taps - High Speed Steel - Hand - Sets on the Small Parts and Bearings website.


Tools - Punches
Tools - Punches

Also see combined categories:
All Tools

Number punch and letter punch sets

Lengths shown are based on standard stock but may vary. This category may be available in the new MBA online store at Tools - Punches.

There is also a good range of Tools - Punches on the Small Parts and Bearings website.


Collars - Shaft - Standard - Aluminium
Collars - Shaft - Standard - Aluminium

Also see combined categories:
All Round Bore Shaft Collars
All Standard Shaft Collars

Standard one piece aluminium shaft collar with set screw

Static torque and axial load are for reference only using steel cup point grub screw on soft steel shaft. This category may be available in the new MBA online store at Collars - Shaft - Standard - Aluminium.

Related Information:

There is also a good range of Collars - Shaft - Standard - Aluminium on the Small Parts and Bearings website.


Collars - Shaft - Standard - Nylon
Collars - Shaft - Standard - Nylon

Also see combined categories:
All Round Bore Shaft Collars
All Standard Shaft Collars

Standard one piece nylon shaft collar with set screw

Static torque and axial load are for reference only using steel cup point grub screw on soft steel shaft. This category may be available in the new MBA online store at Collars - Shaft - Standard - Nylon.

Related Information:

There is also a good range of Collars - Shaft - Standard - Nylon on the Small Parts and Bearings website.


Screws - Hex Head - Steel - Zinc Plated - Full Thread
Screws - Hex Head - Steel - Zinc Plated - Full Thread

Also see combined categories:
All Hex Head Screws

BSW and METRIC - Set Screws

This category may be available in the new MBA online store at Screws - Hex Head - Steel - Zinc Plated - Full Thread.

Related Information:

There is also a good range of Screws - Hex Head - Steel - Zinc Plated - Full Thread on the Small Parts and Bearings website.


Screws - Hex Head - Titanium CP Grade 1
Screws - Hex Head - Titanium CP Grade 1

Also see combined categories:
All Hex Head Screws

Fully threaded hex head set screws (DIN933). CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.

Din 933. Commercially pure for general industrial corrosion applications. UNS R50250. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance. This category may be available in the new MBA online store at Screws - Hex Head - Titanium CP Grade 1.

Related Information:

There is also a good range of Screws - Hex Head - Titanium CP Grade 1 on the Small Parts and Bearings website.


Knobs - Oval Tapered - Press On - Phenolic
Knobs - Oval Tapered - Press On - Phenolic

Also see combined categories:
All Knobs

Press on knobs hold on securely without threads or set screws

Shaft diameter should be +0.000 / - 0.076 mm for best performance. Knob is held in place by a ribbed insert that squeezes onto the shaft. Eliminates machining costs. Knobs will not come off with normal use but can be removed by knocking with a hammer on the underside. This category may be available in the new MBA online store at Knobs - Oval Tapered - Press On - Phenolic.

Related Information:

There is also a good range of Knobs - Oval Tapered - Press On - Phenolic on the Small Parts and Bearings website.


Tools - General
Tools - General

Also see combined categories:
All Tools

Butane Torch, Inspection Mirror, Mini Sandblaster, Nibbling Tool, Plastic Scriber, Pick Up Tool Set, Hex Driver Handle for Insert Bits

X-Acto Knife Sets - Pin Vises - Screw Pitch Gauges and more. This category may be available in the new MBA online store at Tools - General.

There is also a good range of Tools - General on the Small Parts and Bearings website.





Main Pages

5 Axis Machine Tool Bearings About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Distributor Locations Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Satellite Reaction Wheels Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 219038 products in 2167 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 219038 products in 2167 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.