Rod Ends Plastic Categories
Rod Ends - Plastic - Female
Thermoplastic Body / L280(R) Polymer Ball. Also known as Heim Joints
Dimensions not shown are available on request.
There is also a good range of Rod Ends - Plastic - Female on the Small Parts and Bearings website.
Rod Ends - Plastic - Male
Thermoplastic Body / L280(R) Polymer Ball. Also known as Heim Joints
Dimensions not shown are available on request.
There is also a good range of Rod Ends - Plastic - Male on the Small Parts and Bearings website.
You may also be interested in
Balls Plastic
Balls - Plastic - Bored
Bored acetal balls as used in plastic rod ends.
Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight.
Related Information:
There is also a good range of Balls - Plastic - Bored on the Small Parts and Bearings website.
Clevis Joints
Joints - Clevis - Plastic
Use with plastic rod ends - Includes pin and clip. See also yokes.
Comes with clevis pin and retaining clip. Corrosion Resistant, Lightweight. High Tensile Strength (Shown in table as Short Term / Long Term). Vibration Dampening / Noise Dampening. (1) Tensile Strengths shown are Maximum Static axial in Newtons.
There is also a good range of Joints - Clevis - Plastic on the Small Parts and Bearings website.
Bungs
Bungs and Caps - Reversible - Round
Tapered plastic bungs fit inside round tube or over the outside ends of rod, tube or shafting.
Can be used on threaded or unthreaded parts. Used as tuning bungs or rod tips. Helps prevent damage to the product ends. Helps prevent injury from sharp edges.
Related Information:
There is also a good range of Bungs and Caps - Reversible - Round on the Small Parts and Bearings website.
Allthread
Threaded Rod - Allthread - Plastic
UNC - UNF - METRIC - Nylon and PVC. Also known as booker rod.
Light Weight. Non Corrosive. Vibration Resistant.
There is also a good range of Threaded Rod - Allthread - Plastic on the Small Parts and Bearings website.
Cross Blocks - Heavy Duty - Two Knobs
Used for connecting two round rods at 90o.
Adjustments can be made by loosening the hand knob. Plastic knobs function independently for precise adjustment. Knobs have brass insert for easy turning and to prevent galling. Stainlesss steel eye bolt firmly clamps around adjusting rod for superior holding strength. Eyelet does not mar rod when tightened, resulting in smooth rod surface that easily slides through the cross block. No set screws required. Plastic or Stainless bodies accept 12.70 or 15.88mm rods.
There is also a good range of Cross Blocks - Heavy Duty - Two Knobs on the Small Parts and Bearings website.
Cross Blocks - Heavy Duty - Two Nuts
Used for connecting two round rods at 90o.
Adjustments can be made by loosening the hand knob. Plastic knobs function independently for precise adjustment. Stainlesss steel eye bolt firmly clamps around adjusting rod for superior holding strength. Eyelet does not mar rod when tightened, resulting in smooth rod surface that easily slides through the cross block. No set screws required. Plastic or Stainless bodies accept 12.70 or 15.88mm rods.
There is also a good range of Cross Blocks - Heavy Duty - Two Nuts on the Small Parts and Bearings website.
Handles - Latching - 2-Point Locking Rod Kit
Kit can be used with any 5/16in. Square shanked handles for two point locking. Kit includes two gold zinc plated steel rods, two plastic rod guides, steel cam, two steel bushings, two wave washers and three set screws.
There is also a good range of Handles - Latching - 2-Point Locking Rod Kit on the Small Parts and Bearings website.
Cross Blocks - Heavy Duty - One Knob One Nut
Used for connecting two round rods at 90o.
Adjustments can be made by loosening the hand knob. Plastic knobs function independently for precise adjustment. Knobs have brass insert for easy turning and to prevent galling. Stainlesss steel eye bolt firmly clamps around adjusting rod for superior holding strength. Eyelet does not mar rod when tightened, resulting in smooth rod surface that easily slides through the cross block. No set screws required. Plastic or Stainless bodies accept 12.70 or 15.88mm rods.
There is also a good range of Cross Blocks - Heavy Duty - One Knob One Nut on the Small Parts and Bearings website.
Rail Systems - Miniature Profile
Ideal for precision applications where mounting space is limited
Gothic arch grooves at raceway contacts enables slide to sustain loads & movement from any direction. Made from stainless steel or plastic for corrosion resistance. End caps have oil holes for easy relubrication.
There is also a good range of Rail Systems - Miniature Profile on the Small Parts and Bearings website.
Shafting - Ground - Hobby - Steel
Silversteel shafting for hobbies. Not suitable for precision bearings.
Suitable for use with plastic gears, bushes, couplings etc. Not recommended for use with precision steel or stainless steel bearings. Some sizes have special features such as serrations or small barbs (noted in description). Unground ends. Ideal for axles in robotic applications and educational projects.
Related Information:
There is also a good range of Shafting - Ground - Hobby - Steel on the Small Parts and Bearings website.
Balls - Plastic - Acetal
High intensity strength, rigidity, outstanding resistance to abrasion and most solvents.
Tolerances available on request. Acetal Copolymer. High intensity strength, rigidity, outstanding resistance to abrasion and most solvents. Standard Opaque White. Specific Gravity: 1.4.
Related Information:
There is also a good range of Balls - Plastic - Acetal on the Small Parts and Bearings website.
Balls - Plastic - PVC
Polyvinyl chloride. PVC is a chemically stable material, which shows little change in molecular structure, and also exhibits little change in its mechanical strength.
Polyvinyl chloride is a widely used and inexpensive thermoplastic polymer. It is easily worked or machined and has good chemical and biological resistance. It is relatively hard and can be polished to a shine. Polyvinyl chloride is a widely used and inexpensive thermoplastic polymer. Heat Deflection Temperature 176 F / 80 C. Rockwell Hardness 115. Zero water absorption in 24 hours.
Related Information:
There is also a good range of Balls - Plastic - PVC on the Small Parts and Bearings website.
Gauges - Plastic Thickness
Fan blade style has 13 colour-coded thickness blades riveted together for on-site convenience.
Made from polyester and vinyl. Non-corrosive, non-conductive, non-sparking and non-marring.
There is also a good range of Gauges - Plastic Thickness on the Small Parts and Bearings website.
Bearings - Ball - 316 Stainless Steel - Single Row - Sealed
Marine, food and medical grade Stainless Steel - Non Hardenable. Polyethylene plastic seals.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races, greased. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.
Related Information:
There is also a good range of Bearings - Ball - 316 Stainless Steel - Single Row - Sealed on the Small Parts and Bearings website.
Shim - Plastic
Easy to cut - colour coded - plastic shim sheets. Precision thicknesses.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Made from sturdy polyester.
Related Information:
There is also a good range of Shim - Plastic on the Small Parts and Bearings website.
Chain - Roller - Plastic - Simplex
Includes acetal, polyproylene and nylon. Miniature size from 3.1mm up to 12.7mm. Single row.
Snap together construction - no joining links required.
Related Information:
There is also a good range of Chain - Roller - Plastic - Simplex on the Small Parts and Bearings website.
Universal Joints - Telescoping - Plastic - Brass Spider and Insert
Acetal plastic telescoping universal joints with nickle plated brass spiders and bore inserts
There is also a good range of Universal Joints - Telescoping - Plastic - Brass Spider and Insert on the Small Parts and Bearings website.
Bearings - Acetal - Solid - For Plastic Housings
Insert bearings ideal for wet conditions. Similar to wide inner ring bearings for P, F, Fl type housings but solid plastic.
Load and speed calculations are for reference only. Testing is recommended.
Related Information:
There is also a good range of Bearings - Acetal - Solid - For Plastic Housings on the Small Parts and Bearings website.
Gears - Mitre - Module 0.5 - Plastic
1:1 Ratio. 20o Pressure Angle - Acetal
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios.
Related Information:
There is also a good range of Gears - Mitre - Module 0.5 - Plastic on the Small Parts and Bearings website.
Gears - Mitre - Module 1 - Plastic
1:1 Ratio. 20o Pressure Angle - Acetal.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios.
Related Information:
There is also a good range of Gears - Mitre - Module 1 - Plastic on the Small Parts and Bearings website.
Gears - Mitre - Module 3 - Plastic
1:1 Ratio. 20o Pressure Angle - Acetal
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios.
Related Information:
There is also a good range of Gears - Mitre - Module 3 - Plastic on the Small Parts and Bearings website.
Gears - Spur - Module 0.4 - Plastic
PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 0.4 - Plastic on the Small Parts and Bearings website.
Gears - Spur - Module 0.5 - Plastic
PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 0.5 - Plastic on the Small Parts and Bearings website.
Gears - Spur - Module 0.7 - Plastic
PCD = No. of Teeth x 0.700mm. 20o Pressure Angle. Acetal.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 0.7 - Plastic on the Small Parts and Bearings website.
Gears - Spur - Module 0.8 - Plastic
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 0.8 - Plastic on the Small Parts and Bearings website.
Gears - Spur - Module 1.5 - Plastic
PCD = No. of Teeth x 1.500mm. 20o Pressure Angle. Acetal and Nylon
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 1.5 - Plastic on the Small Parts and Bearings website.
Gears - Spur - Module 1 - Plastic
PCD = No. of Teeth x 1.000mm. 20o Pressure Angle. Acetal
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 1 - Plastic on the Small Parts and Bearings website.
Gears - Bevel - Module 0.5 - Plastic
For 90o angle power transfer. Ratios exceeding 1 to 1. Acetal.
20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
Related Information:
There is also a good range of Gears - Bevel - Module 0.5 - Plastic on the Small Parts and Bearings website.
Gears - Spur - Module 0.4 - Plastic with Insert
PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 0.4 - Plastic with Insert on the Small Parts and Bearings website.
Gears - Spur - Module 0.5 - Plastic with Insert
PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 0.5 - Plastic with Insert on the Small Parts and Bearings website.
Gears - Spur - Module 0.8 - Plastic with Insert
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 0.8 - Plastic with Insert on the Small Parts and Bearings website.
Plastic Bearing Oliver Design - Xyratex Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
There is also a good range of Plastic Bearing Oliver Design - Xyratex Parts on the Small Parts and Bearings website.
Bearings - Acetal - MRI Table
Special acetal bearings for MRI table wheels
There is also a good range of Bearings - Acetal - MRI Table on the Small Parts and Bearings website.
Bearings - Acetal - Special Purpose
Special acetal bearings for Bicycle Chain Derailer and special effects lighting systems
Related Information:
There is also a good range of Bearings - Acetal - Special Purpose on the Small Parts and Bearings website.
Bearings - Acetal - Special Types
Light duty acetal bearings used for drawer runners, light duty tracks, garage doors and more.
See descriptions for special features. Not all items are listed in this category. Please contact us if you have a similar type bearing with different dimensions.
There is also a good range of Bearings - Acetal - Special Types on the Small Parts and Bearings website.
Washers - Flat - PVC
Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic
Flat washers.
Related Information:
There is also a good range of Washers - Flat - PVC on the Small Parts and Bearings website.
Bearings for Pool Equipment
Acetal bearings for spa jets and pool vacuum wheels
No lubrication required other than the water they are running in.
Related Information:
There is also a good range of Bearings for Pool Equipment on the Small Parts and Bearings website.
Sprockets - 3.12 x 1.47mm - Simplex - Plastic
Nylon - Acetal - With and without bore inserts.
Match with series 3.12mm miniature plastic chain.
Related Information:
There is also a good range of Sprockets - 3.12 x 1.47mm - Simplex - Plastic on the Small Parts and Bearings website.
Sprockets - 3.75 x 1.6mm - Simplex - Plastic
Nylon - Acetal - With and without bore inserts.
Match with series 3.75mm miniature plastic or stainless chain.
Related Information:
There is also a good range of Sprockets - 3.75 x 1.6mm - Simplex - Plastic on the Small Parts and Bearings website.
Sprockets - 6.35 x 2.8mm - Simplex - Plastic
Nylon - Acetal - With and without bore inserts.
Match with series 6.35mm plastic or steel chain (25-1 ASA). American Standard 25-1 - 1/4 inch.
Related Information:
There is also a good range of Sprockets - 6.35 x 2.8mm - Simplex - Plastic on the Small Parts and Bearings website.
Sprockets - 9.53 x 4.7mm - Simplex - Plastic
Nylon - Acetal - With and without bore inserts.
Match with series 9.53x4.7mm plastic or steel chain (35-1 ASA). American Standard 35-1 - 3/8 inch.
Related Information:
There is also a good range of Sprockets - 9.53 x 4.7mm - Simplex - Plastic on the Small Parts and Bearings website.
Sprockets - 9.53 x 5.7mm - Simplex - Plastic
Nylon - Acetal - With and without bore inserts.
Match with series 9.53x5.7mm steel chain (06B BS). British Standard 06B - 3/8 inch.
Related Information:
There is also a good range of Sprockets - 9.53 x 5.7mm - Simplex - Plastic on the Small Parts and Bearings website.
Housings - Bearing - Flanged - 2 Bolt Hole - Plastic
Load and speed capability depend on the bearing used. Use with steel or plastic bearing inserts for plastic housings.
Related Information:
There is also a good range of Housings - Bearing - Flanged - 2 Bolt Hole - Plastic on the Small Parts and Bearings website.
Housings - Bearing - Flanged - 3 Bolt Bracket - Plastic
Load and speed capability depend on the bearing used. Use with steel bearing inserts for plastic housings.
Related Information:
There is also a good range of Housings - Bearing - Flanged - 3 Bolt Bracket - Plastic on the Small Parts and Bearings website.
Gears - Bevel - 32 Diametrical Pitch - Plastic
For 90o angle power transfer. Ratios exceeding 1 to 1. Nylon and Acetal.
20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
Related Information:
There is also a good range of Gears - Bevel - 32 Diametrical Pitch - Plastic on the Small Parts and Bearings website.
Gears - Bevel - 48 Diametrical Pitch - Plastic
For 90o angle power transfer. Ratios exceeding 1 to 1. Nylon and Acetal.
20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
Related Information:
There is also a good range of Gears - Bevel - 48 Diametrical Pitch - Plastic on the Small Parts and Bearings website.
Gears - Spur - 48DP - 20 Degree - Plastic
PCD = No. of Teeth x 0.529mm (1/48 in.). 20o Pressure Angle. Acetal and nylon. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 48 Diametrical Pitch. Approx 1.66mm between teeth.
There is also a good range of Gears - Spur - 48DP - 20 Degree - Plastic on the Small Parts and Bearings website.
Gears - Spur - 16DP - 20 Degree - Plastic
PCD = No. of Teeth x 1.588mm (1/16 in.). 20o Pressure Angle. Nylon and acetal. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 16 Diametrical Pitch. Approx 4.99mm between teeth.
There is also a good range of Gears - Spur - 16DP - 20 Degree - Plastic on the Small Parts and Bearings website.
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Contact Us
Charity
Dental Bearings
Distributor Locations
Dowel Pins
Downloadable PDF Catalogue Ball Lock Pins
Downloadable PDF Catalogue Balls
Downloadable PDF Catalogue Ceramic Bearings
Downloadable PDF Catalogue Circlips
Downloadable PDF Catalogue Clevis Pins
Downloadable PDF Catalogue Corrosion Resistant Bearings
Downloadable PDF Catalogue Disc Springs
Downloadable PDF Catalogue Dowel Pins
Downloadable PDF Catalogue Economy Bearings
Downloadable PDF Catalogue Hammer Drive Pins
Downloadable PDF Catalogue High Speed Bearings
Downloadable PDF Catalogue Key Steel
Downloadable PDF Catalogue Knobs
Downloadable PDF Catalogue Leveling Mounts
Downloadable PDF Catalogue Metallic Bushes
Downloadable PDF Catalogue O-Rings
Downloadable PDF Catalogue Pins
Downloadable PDF Catalogue Plastic Bearings
Downloadable PDF Catalogue Polyvee Belts and Pulleys
Downloadable PDF Catalogue Precision Shim Washers
Downloadable PDF Catalogue Push On and Push In Rings
Downloadable PDF Catalogue Rod & Tube
Downloadable PDF Catalogue Roll Pins
Downloadable PDF Catalogue Shaft Collars
Downloadable PDF Catalogue Shim Sheet
Downloadable PDF Catalogue Shoulder Screws
Downloadable PDF Catalogue Sintered Bronze Bushes
Downloadable PDF Catalogue Snap Rings
Downloadable PDF Catalogue Socket Set Screws
Downloadable PDF Catalogue Solid Bronze Bushes
Downloadable PDF Catalogue Spring Steel Strip
Downloadable PDF Catalogue Springs
Downloadable PDF Catalogue Standard Ball Bearing Range
Downloadable PDF Catalogue Super Precision Bearings
Downloadable PDF Catalogue Taper Pins
Downloadable PDF Catalogue Thrust Bearings
Downloadable PDF Catalogue Thumb Screws and Nuts
Downloadable PDF Catalogue Timing Belts
Downloadable PDF Catalogue Timing Pulley Stock
Downloadable PDF Catalogue Timing Pulleys
Downloadable PDF Catalogue Vibration Mounts
Downloadable PDF Catalogue Washers
Downloadable PDF Catalogue Wave Washers
Downloadable PDF Cross Reference ADR and SKF
Downloadable PDF Cross Reference Anderton Circlips
Downloadable PDF Cross Reference Barden Bearings
Downloadable PDF Cross Reference Essentra
Downloadable PDF Cross Reference Flocast
Downloadable PDF Cross Reference K&S Metals
Downloadable PDF Cross Reference McMaster Carr
Downloadable PDF Cross Reference Miniature Precison Bearings
Downloadable PDF Cross Reference Nordex
Downloadable PDF Cross Reference NSK and NTN
Downloadable PDF Cross Reference Ondrives
Downloadable PDF Cross Reference Reid Supply
Downloadable PDF Cross Reference SDP-SI Designatronics
Downloadable PDF Cross Reference Seeger Circlips
Downloadable PDF Cross Reference Sintered Bronze
Downloadable PDF Cross Reference Small Parts Inc
Downloadable PDF Cross Reference Timing Belts and Pulleys
Freight Rates and Shipping Times
Frequently Asked Questions
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Satellite Reaction Wheels
Shipping Rates and Times
Technical
Terms
5 Axis Machine Tool Bearings
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)
Miniature Bearings Australia offers 130510 products in 2127 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.
