Miniature Bearings Australia Pty Ltd

Pinion wire metric categories


Pinion Wire Imperial


Gears - Pinion Wire - 32 Diametrical Pitch
Gears - Pinion Wire - 32 Diametrical Pitch

Also see combined categories:
All Imperial Pinion Wire

Brass and carbon steel.

Please note that very thin pinion wire may not be supplied perfectly straight. Pinion wire is meant to be cut into much smaller pieces to make pinion gears so the slight bends in the long length will have no effect on the intended use. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at Gears - Pinion Wire - 32 Diametrical Pitch.

There is also a good range of Gears - Pinion Wire - 32 Diametrical Pitch on the Small Parts and Bearings website.


You may also be interested in

Spring Wire


Wire - Steel - Spring - Music Wire - Short Lengths
Wire - Steel - Spring - Music Wire - Short Lengths

Also see combined categories:
All Spring Wire

SAE 1090 Spring Steel. Includes inch and metric sizes.

Metric and imperial. Shipped in sturdy mail tubes. This category may be available in the new MBA online store at Wire - Steel - Spring - Music Wire - Short Lengths.

Related Information:

There is also a good range of Wire - Steel - Spring - Music Wire - Short Lengths on the Small Parts and Bearings website.


Leadscrews


Leadscrews - Metric - Rolled Thread - Stainless Steel
Leadscrews - Metric - Rolled Thread - Stainless Steel

Also see combined categories:
All Metric Leadscrews

Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.

Stainless steel. For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.

Related Information:


Shafting Precision Ground


Shafts - Pinion
Shafts - Pinion


This category may be available in the new MBA online store at Shafts - Pinion.

There is also a good range of Shafts - Pinion on the Small Parts and Bearings website.


Pins Taper


Pins - Taper - Metric - Carbon Steel
Pins - Taper - Metric - Carbon Steel

Also see combined categories:
All Metric Taper Pins

Metric Sizes Tapered 1:50. DIN 1 - A - Ground Ra 0.8um

Metric Sizes to DIN 1. This category may be available in the new MBA online store at Pins - Taper - Metric - Carbon Steel.

Related Information:

There is also a good range of Pins - Taper - Metric - Carbon Steel on the Small Parts and Bearings website.


Pins - Taper - Metric - Extractable - External Thread
Pins - Taper - Metric - Extractable - External Thread

Also see combined categories:
All Metric Taper Pins

Metric Sizes Tapered 1:50 and threaded externally for easy extraction.

DIN 7977. This category may be available in the new MBA online store at Pins - Taper - Metric - Extractable - External Thread.

Related Information:

There is also a good range of Pins - Taper - Metric - Extractable - External Thread on the Small Parts and Bearings website.


Pins - Taper - Metric - Extractable - Internal Thread
Pins - Taper - Metric - Extractable - Internal Thread

Also see combined categories:
All Metric Taper Pins

Metric Sizes Tapered 1:50 and threaded internally for easy extraction.

DIN 7978. This category may be available in the new MBA online store at Pins - Taper - Metric - Extractable - Internal Thread.

Related Information:

There is also a good range of Pins - Taper - Metric - Extractable - Internal Thread on the Small Parts and Bearings website.


Pins - Taper - Metric - Stainless Steel
Pins - Taper - Metric - Stainless Steel

Also see combined categories:
All Metric Taper Pins

Metric Sizes Tapered 1:50. DIN 1 - A - Ground Ra 0.8um

Metric Sizes to DIN 1. This category may be available in the new MBA online store at Pins - Taper - Metric - Stainless Steel.

Related Information:

There is also a good range of Pins - Taper - Metric - Stainless Steel on the Small Parts and Bearings website.


Leadscrews


Leadscrew Nuts - Metric - Round - Metallic
Leadscrew Nuts - Metric - Round - Metallic

Also see combined categories:
All Leadscrew Nuts
All Metric Leadscrew Nuts

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: KSM = Carbon Manganese Steel S300 Pb (11 SMn Pb37) / LRM = Bronze CuSn8P. Carbon Manganese steel can be welded but difficulties may arise with bubbling due to sulphur content. KSM: Manual control control only - low rotational speeds only - for clamping or locking functions - for receiving dead weights. LRM: Manual or powered control - low and medium rotational speeds - for working under load. For power transmission and continuous use always use bronze nuts not steel.

Related Information:

There is also a good range of Leadscrew Nuts - Metric - Round - Metallic on the Small Parts and Bearings website.


Leadscrew Nuts - Metric - Square - Metallic
Leadscrew Nuts - Metric - Square - Metallic

Also see combined categories:
All Leadscrew Nuts
All Metric Leadscrew Nuts

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.

Related Information:

There is also a good range of Leadscrew Nuts - Metric - Square - Metallic on the Small Parts and Bearings website.


Springs Die


Springs - Die - Metric - Extra Heavy Duty
Springs - Die - Metric - Extra Heavy Duty

Also see combined categories:
All Metric Die Springs
All All Die Springs

Colour coded yellow

High tensile strength chromium alloy steels. Heat Resistance: Up to +230oC (Loss of load occurs above +120oC). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length. This category may be available in the new MBA online store at Springs - Die - Metric - Extra Heavy Duty.

Related Information:

There is also a good range of Springs - Die - Metric - Extra Heavy Duty on the Small Parts and Bearings website.


Springs - Die - Metric - Heavy Duty
Springs - Die - Metric - Heavy Duty

Also see combined categories:
All Metric Die Springs
All All Die Springs

Colour coded red

High tensile strength chromium alloy steels. Heat Resistance: Up to +230oC (Loss of load occurs above +120oC). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length. This category may be available in the new MBA online store at Springs - Die - Metric - Heavy Duty.

Related Information:

There is also a good range of Springs - Die - Metric - Heavy Duty on the Small Parts and Bearings website.


Springs - Die - Metric - Light Duty
Springs - Die - Metric - Light Duty

Also see combined categories:
All Metric Die Springs
All All Die Springs

Colour coded green

High tensile strength chromium alloy steels. Heat Resistance: Up to +230oC (Loss of load occurs above +120oC). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length. This category may be available in the new MBA online store at Springs - Die - Metric - Light Duty.

Related Information:

There is also a good range of Springs - Die - Metric - Light Duty on the Small Parts and Bearings website.


Springs - Die - Metric - Medium Duty
Springs - Die - Metric - Medium Duty

Also see combined categories:
All Metric Die Springs
All All Die Springs

Colour coded blue

High tensile strength chromium alloy steels. Heat Resistance: Up to +230oC (Loss of load occurs above +120oC). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length. This category may be available in the new MBA online store at Springs - Die - Metric - Medium Duty.

Related Information:

There is also a good range of Springs - Die - Metric - Medium Duty on the Small Parts and Bearings website.


Studs


Studs - Threaded - Standard
Studs - Threaded - Standard


Metric and imperial sizes. Steel and 303 stainless steel.

Yield strength 100,000 PSI. Tensile strength 125,000 PSI. This category may be available in the new MBA online store at Studs - Threaded - Standard.

There is also a good range of Studs - Threaded - Standard on the Small Parts and Bearings website.


Bearings Tapered Roller


Bearings - Tapered Roller - Single Row - Metric
Bearings - Tapered Roller - Single Row - Metric


Includes cup and cone

This category may be available in the new MBA online store at Bearings - Tapered Roller - Single Row - Metric.


Nuts Hex


Nuts - Hexagonal - Aluminium
Nuts - Hexagonal - Aluminium

Also see combined categories:
All Nuts

METRIC.

Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. This category may be available in the new MBA online store at Nuts - Hexagonal - Aluminium.

Related Information:

There is also a good range of Nuts - Hexagonal - Aluminium on the Small Parts and Bearings website.


Screws - Security - Button - Socket
Screws - Security - Button - Socket

Also see combined categories:
All Security Screws

Metric only.

Use special tool listed under Screws - Security - Socket - Tools.. This category may be available in the new MBA online store at Screws - Security - Button - Socket.

Related Information:

There is also a good range of Screws - Security - Button - Socket on the Small Parts and Bearings website.


Screws - Security - Cap - Socket
Screws - Security - Cap - Socket

Also see combined categories:
All Security Screws

Metric only.

Use special tool listed under Screws - Security - Socket - Tools.. This category may be available in the new MBA online store at Screws - Security - Cap - Socket.

Related Information:

There is also a good range of Screws - Security - Cap - Socket on the Small Parts and Bearings website.


Gears - Bevel - Module 1.5 - Plastic
Gears - Bevel - Module 1.5 - Plastic

Also see combined categories:
All Metric Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. This category may be available in the new MBA online store at Gears - Bevel - Module 1.5 - Plastic.

Related Information:

There is also a good range of Gears - Bevel - Module 1.5 - Plastic on the Small Parts and Bearings website.


Gears - Bevel - Module 1 - Plastic
Gears - Bevel - Module 1 - Plastic

Also see combined categories:
All Metric Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. This category may be available in the new MBA online store at Gears - Bevel - Module 1 - Plastic.

Related Information:

There is also a good range of Gears - Bevel - Module 1 - Plastic on the Small Parts and Bearings website.


Gears - Mitre - Module 0.5 - Plastic
Gears - Mitre - Module 0.5 - Plastic

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Acetal

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 0.5 - Plastic.

Related Information:

There is also a good range of Gears - Mitre - Module 0.5 - Plastic on the Small Parts and Bearings website.


Gears - Mitre - Module 1.5 - Brass
Gears - Mitre - Module 1.5 - Brass

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 1.5 - Brass.

Related Information:

There is also a good range of Gears - Mitre - Module 1.5 - Brass on the Small Parts and Bearings website.


Gears - Mitre - Module 1 - Brass
Gears - Mitre - Module 1 - Brass

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 1 - Brass.

Related Information:

There is also a good range of Gears - Mitre - Module 1 - Brass on the Small Parts and Bearings website.


Gears - Mitre - Module 1 - Plastic
Gears - Mitre - Module 1 - Plastic

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Acetal.

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 1 - Plastic.

Related Information:

There is also a good range of Gears - Mitre - Module 1 - Plastic on the Small Parts and Bearings website.


Gears - Mitre - Module 3 - Plastic
Gears - Mitre - Module 3 - Plastic

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Acetal

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 3 - Plastic.

Related Information:

There is also a good range of Gears - Mitre - Module 3 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.4 - Brass
Gears - Spur - Module 0.4 - Brass

Also see combined categories:
All Module 0.4 Spur Gears
All Metal Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.4 - Brass.

There is also a good range of Gears - Spur - Module 0.4 - Brass on the Small Parts and Bearings website.


Gears - Spur - Module 0.4 - Plastic
Gears - Spur - Module 0.4 - Plastic

Also see combined categories:
All Module 0.4 Spur Gears
All Plastic Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.4 - Plastic.

There is also a good range of Gears - Spur - Module 0.4 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.5 - Plastic
Gears - Spur - Module 0.5 - Plastic

Also see combined categories:
All Module 0.5 Spur Gears
All Plastic Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.5 - Plastic.

There is also a good range of Gears - Spur - Module 0.5 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.5 - Stainless
Gears - Spur - Module 0.5 - Stainless

Also see combined categories:
All Module 0.5 Spur Gears
All Metal Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.5 - Stainless.

There is also a good range of Gears - Spur - Module 0.5 - Stainless on the Small Parts and Bearings website.


Gears - Spur - Module 0.7 - Plastic
Gears - Spur - Module 0.7 - Plastic


PCD = No. of Teeth x 0.700mm. 20o Pressure Angle. Acetal.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.7 - Plastic.

There is also a good range of Gears - Spur - Module 0.7 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.8 - Aluminium
Gears - Spur - Module 0.8 - Aluminium

Also see combined categories:
All Module 0.8 Spur Gears
All Metal Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 2024 aluminium

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Aluminium.

There is also a good range of Gears - Spur - Module 0.8 - Aluminium on the Small Parts and Bearings website.


Gears - Spur - Module 0.8 - Plastic
Gears - Spur - Module 0.8 - Plastic

Also see combined categories:
All Module 0.8 Spur Gears
All Plastic Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Plastic.

There is also a good range of Gears - Spur - Module 0.8 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.8 - Stainless
Gears - Spur - Module 0.8 - Stainless

Also see combined categories:
All Module 0.8 Spur Gears
All Metal Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Stainless.

There is also a good range of Gears - Spur - Module 0.8 - Stainless on the Small Parts and Bearings website.


Gears - Spur - Module 1.25 - Stainless
Gears - Spur - Module 1.25 - Stainless

Also see combined categories:
All Module 1.25 Spur Gears
All Metal Module 1.25 Spur Gears

PCD = No. of Teeth x 1.250mm. 20o Pressure Angle. 303 stainless steel

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 1.25 - Stainless.

There is also a good range of Gears - Spur - Module 1.25 - Stainless on the Small Parts and Bearings website.


Gears - Spur - Module 1.5 - Plastic
Gears - Spur - Module 1.5 - Plastic

Also see combined categories:
All Module 1.5 Spur Gears
All Plastic Module 1.5 Spur Gears

PCD = No. of Teeth x 1.500mm. 20o Pressure Angle. Acetal and Nylon

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 1.5 - Plastic.

There is also a good range of Gears - Spur - Module 1.5 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 1 - Plastic
Gears - Spur - Module 1 - Plastic

Also see combined categories:
All Module 1.0 Spur Gears
All Plastic Module 1.0 Spur Gears

PCD = No. of Teeth x 1.000mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 1 - Plastic.

There is also a good range of Gears - Spur - Module 1 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 3 - Plastic
Gears - Spur - Module 3 - Plastic

Also see combined categories:
All Module 3.0 Spur Gears

PCD = No. of Teeth x 3.000mm. 20o Pressure Angle. Nylon

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 3 - Plastic.

There is also a good range of Gears - Spur - Module 3 - Plastic on the Small Parts and Bearings website.


Threaded Rod - Allthread - Brass
Threaded Rod - Allthread - Brass

Also see combined categories:
All Threaded Rod

UNC - UNF - METRIC brass. Also known as booker rod.

This category may be available in the new MBA online store at Threaded Rod - Allthread - Brass.

There is also a good range of Threaded Rod - Allthread - Brass on the Small Parts and Bearings website.


Threaded Rod - Allthread - Plastic
Threaded Rod - Allthread - Plastic

Also see combined categories:
All Threaded Rod

UNC - UNF - METRIC - Nylon and PVC. Also known as booker rod.

Light Weight. Non Corrosive. Vibration Resistant. This category may be available in the new MBA online store at Threaded Rod - Allthread - Plastic.

There is also a good range of Threaded Rod - Allthread - Plastic on the Small Parts and Bearings website.


Screws - Security - Socket - Countersunk - Stainless
Screws - Security - Socket - Countersunk - Stainless

Also see combined categories:
All Security Screws

Metric only.

Use special tool listed under Screws - Security - Socket - Tools.. This category may be available in the new MBA online store at Screws - Security - Socket - Countersunk - Stainless.

Related Information:

There is also a good range of Screws - Security - Socket - Countersunk - Stainless on the Small Parts and Bearings website.


Gears - Mitre - Module 1 - Zinc Diecast
Gears - Mitre - Module 1 - Zinc Diecast

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 1 - Zinc Diecast.

Related Information:

There is also a good range of Gears - Mitre - Module 1 - Zinc Diecast on the Small Parts and Bearings website.


Gears - Mitre - Module 2 - Zinc Diecast
Gears - Mitre - Module 2 - Zinc Diecast

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 2 - Zinc Diecast.

Related Information:

There is also a good range of Gears - Mitre - Module 2 - Zinc Diecast on the Small Parts and Bearings website.


Gears - Mitre - Spiral - Module 1.5 - Steel
Gears - Mitre - Spiral - Module 1.5 - Steel

Also see combined categories:
All Metric Mitre Gears
All Metric Spiral Mitre Gears

1:1 Ratio. 20o Pressure Angle - 35o Spiral tooth - Steel.

A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Spiral - Module 1.5 - Steel.

Related Information:

There is also a good range of Gears - Mitre - Spiral - Module 1.5 - Steel on the Small Parts and Bearings website.


Gears - Mitre - Spiral - Module 3.5 - Steel
Gears - Mitre - Spiral - Module 3.5 - Steel

Also see combined categories:
All Metric Mitre Gears
All Metric Spiral Mitre Gears

1:1 Ratio. 20o Pressure Angle - 35o Spiral tooth - Steel.

A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Spiral - Module 3.5 - Steel.

There is also a good range of Gears - Mitre - Spiral - Module 3.5 - Steel on the Small Parts and Bearings website.


Circlips - External - Standard - Berryllium Copper
Circlips - External - Standard - Berryllium Copper

Also see combined categories:
All External Circlips

Imperial and metric DIN471 / N1400 / D1460. Retaining rings. Snap Rings (USA).

This category may be available in the new MBA online store at Circlips - External - Standard - Berryllium Copper.

Related Information:

There is also a good range of Circlips - External - Standard - Berryllium Copper on the Small Parts and Bearings website.


Circlips - External - Standard - Carbon Steel
Circlips - External - Standard - Carbon Steel

Also see combined categories:
All External Circlips

Imperial and metric DIN471 / D1400 / N1400 / D1460. Retaining rings. Snap Rings (USA).

Plain carbon steel. This category may be available in the new MBA online store at Circlips - External - Standard - Carbon Steel.

Related Information:

There is also a good range of Circlips - External - Standard - Carbon Steel on the Small Parts and Bearings website.


Circlips - External - Standard - Stainless Steel
Circlips - External - Standard - Stainless Steel

Also see combined categories:
All External Circlips

Imperial and metric DIN471 / D1400 / N1400 / D1460. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).

PH15-7 Mo Stainless Steel. This category may be available in the new MBA online store at Circlips - External - Standard - Stainless Steel.

Related Information:

There is also a good range of Circlips - External - Standard - Stainless Steel on the Small Parts and Bearings website.


Circlips - External - Standard - Zinc Plated
Circlips - External - Standard - Zinc Plated

Also see combined categories:
All External Circlips

Imperial and metric DIN471 / D1400 / N1400 / D1460. Retaining rings. Snap Rings (USA).

Zinc plated carbon steel. This category may be available in the new MBA online store at Circlips - External - Standard - Zinc Plated.

Related Information:

There is also a good range of Circlips - External - Standard - Zinc Plated on the Small Parts and Bearings website.


Circlips - Internal - Standard - Carbon Steel
Circlips - Internal - Standard - Carbon Steel

Also see combined categories:
All Internal Circlips

Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).

Plain carbon steel. Tolerances on request. This category may be available in the new MBA online store at Circlips - Internal - Standard - Carbon Steel.

Related Information:

There is also a good range of Circlips - Internal - Standard - Carbon Steel on the Small Parts and Bearings website.





Main Pages

5 Axis Machine Tool Bearings About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Charity Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Distributor Locations Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Satellite Reaction Wheels Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 212690 products in 2107 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 212690 products in 2107 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.