Miniature Bearings Australia Pty Ltd

Locking Bushings Categories


Bushings - Integral Taper
Bushings - Integral Taper

Also see combined categories:
All Locking Assemblies
All Locking Bushings

Stainless Steel Taper Bushings.

Will not mar shafts.

There is also a good range of Bushings - Integral Taper on the Small Parts and Bearings website.


You may also be interested in

Latches Handle


Handles - Latching - 2-Point Locking Rod Kit
Handles - Latching - 2-Point Locking Rod Kit


Kit can be used with any 5/16in. Square shanked handles for two point locking. Kit includes two gold zinc plated steel rods, two plastic rod guides, steel cam, two steel bushings, two wave washers and three set screws.


There is also a good range of Handles - Latching - 2-Point Locking Rod Kit on the Small Parts and Bearings website.


Bushings - Snap - Closed
Bushings - Snap - Closed


Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Open snap bushings are designed to provide protection from sharp edges where cable or hose runs through plate steel.

Similar to a bung, but designed with expanding catch for use in holes in sheet products. Also see grommets for a similar product made from rubber.

Related Information:

There is also a good range of Bushings - Snap - Closed on the Small Parts and Bearings website.


Bushings - Snap - Open
Bushings - Snap - Open


Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Closed snap bushings are designed to keep out dust and other contaminants and protect from sharp edges where cable or hose used to run through a hole in plate steel.

Also called a dome plug. Also see grommets for a similar product made from rubber.

Related Information:

There is also a good range of Bushings - Snap - Open on the Small Parts and Bearings website.


Pins - Dowel Bushings
Pins - Dowel Bushings

Also see combined categories:
All Dowel Bushings

Series DB100 Spirol

Spring Steel. Precision rolled bushes manufactured from spring steel. Designed to eliminate the need for separate dowling where two components are to be located accurately together and fastened with bolts. They are available for use with bolts from M5 to M12.

Related Information:

There is also a good range of Pins - Dowel Bushings on the Small Parts and Bearings website.


Bushings - QD
Bushings - QD


Used with QD type cast iron vee pulleys, timing pulleys, sprockets, poly vee pulleys and other parts designed specifically for use with a QD bushing

Similar to a taperlock bush, but not interchangeable. QD bushings like taperlock bushings allow for use of a single stock pulley for many applications with different shaft sizes. Select the correct QD series to suit the pulley.

Related Information:

There is also a good range of Bushings - QD on the Small Parts and Bearings website.


Bushings - Taperlock
Bushings - Taperlock



There is also a good range of Bushings - Taperlock on the Small Parts and Bearings website.


Bushings - Spherical - Plastic
Bushings - Spherical - Plastic

Also see combined categories:
All Spherical Bushings

Plastic spherical plain bearings. Also known as ball bushings.

Ball Material W300. Housing Iglidur G. Maintenance Free. Self lubricating. Compensates for axial loads and misalignment. Corrosion resistant. High vibration dampening capacity.

There is also a good range of Bushings - Spherical - Plastic on the Small Parts and Bearings website.


Bushings - Spherical - Steel
Bushings - Spherical - Steel

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.

There is also a good range of Bushings - Spherical - Steel on the Small Parts and Bearings website.


Bushings - Spherical - Steel - With Oil Hole
Bushings - Spherical - Steel - With Oil Hole

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.

There is also a good range of Bushings - Spherical - Steel - With Oil Hole on the Small Parts and Bearings website.


Bushings - Spherical - Steel - With Oil Hole and Wiper Seal
Bushings - Spherical - Steel - With Oil Hole and Wiper Seal

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.

There is also a good range of Bushings - Spherical - Steel - With Oil Hole and Wiper Seal on the Small Parts and Bearings website.


Bushings - Spherical - Steel - With Wiper Seal
Bushings - Spherical - Steel - With Wiper Seal

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.

There is also a good range of Bushings - Spherical - Steel - With Wiper Seal on the Small Parts and Bearings website.


Bushings - Drill - Liner Type - Headless
Bushings - Drill - Liner Type - Headless

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.

There is also a good range of Bushings - Drill - Liner Type - Headless on the Small Parts and Bearings website.


Bushings - Drill - Press-fit - Headless
Bushings - Drill - Press-fit - Headless

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.


There is also a good range of Bushings - Drill - Press-fit - Headless on the Small Parts and Bearings website.


Bushings - Drill - Press-fit - Headless - Tungsten Carbide
Bushings - Drill - Press-fit - Headless - Tungsten Carbide

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.

There is also a good range of Bushings - Drill - Press-fit - Headless - Tungsten Carbide on the Small Parts and Bearings website.


Bushings - Drill - Press-fit - Standard Head
Bushings - Drill - Press-fit - Standard Head

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.


There is also a good range of Bushings - Drill - Press-fit - Standard Head on the Small Parts and Bearings website.


Bushings - Drill - Slip - With Head
Bushings - Drill - Slip - With Head

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.

There is also a good range of Bushings - Drill - Slip - With Head on the Small Parts and Bearings website.


Bushings - Tension
Bushings - Tension


Like a heavy duty roll pin.

Made of a high carbon spring steel with high elasticity, resilience and wear characteristics. Designed to replace solid steel tubular and case hardened bushings because they are close tolerance, self-retaining and through hard. Insertion can be easily accomplished with a hammer and drift. Ideal for high load/low-speed operation in articulating or continuous applications.

There is also a good range of Bushings - Tension on the Small Parts and Bearings website.


Bushings - Stroke Rotary - Miniature
Bushings - Stroke Rotary - Miniature

Also see combined categories:
All Stroke Rotary Bushings

2 to 12mm Shaft Sizes. Can operate in both linear and rotary directions at the same time.

Set includes outer ring, ball cage and shaft. Ball Cage: Brass Balls: Hard Steel / Shaft: Hard Steel Outer Ring: Hard Steel. Temperature: +100oC (Constant), +120oC (Maximum). Stroke: = (L1 - Lb) x 2. Supplied with extreme accuracy with zero to minimum preload.

Related Information:

There is also a good range of Bushings - Stroke Rotary - Miniature on the Small Parts and Bearings website.


Bushings - Shoulder
Bushings - Shoulder


Mould components


There is also a good range of Bushings - Shoulder on the Small Parts and Bearings website.


Dual Vee - Adaptor Bushings
Dual Vee - Adaptor Bushings


Vee grooved track roller bushings.

Stationary bushings have a concentric hole. Adjustable bushings have an eccentric hole allowing positioning of the guide wheel as the bush is turned.

Related Information:

There is also a good range of Dual Vee - Adaptor Bushings on the Small Parts and Bearings website.


Spacers - Machinery Bushings
Spacers - Machinery Bushings

Also see combined categories:
All Round Spacers
All Flat Washers and Spacers - Metallic

Used as spacers between pulleys, gears etc

Low carbon mild steel.

There is also a good range of Spacers - Machinery Bushings on the Small Parts and Bearings website.


Cam Followers - Self Lubricating - Bronze Bushing
Cam Followers - Self Lubricating - Bronze Bushing

Also see combined categories:
All Cam Followers


There is also a good range of Cam Followers - Self Lubricating - Bronze Bushing on the Small Parts and Bearings website.


Plungers - Indexing - Locking - With Knob - 303 stainless Steel
Plungers - Indexing - Locking - With Knob - 303 stainless Steel

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.

303 Stainless Steel.

There is also a good range of Plungers - Indexing - Locking - With Knob - 303 stainless Steel on the Small Parts and Bearings website.


Plungers - Indexing - Locking - With Knob - Steel
Plungers - Indexing - Locking - With Knob - Steel

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.

Body and pin are steel with black oxide finish.

There is also a good range of Plungers - Indexing - Locking - With Knob - Steel on the Small Parts and Bearings website.


Plungers - Indexing - Locking - With Mounting Plate - Steel
Plungers - Indexing - Locking - With Mounting Plate - Steel

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.

Spring loaded to work in a variety of applications on both tooling and equipment that require surface mounting. Plunger is hardened and ground. Knob is black matte plastic. Mounting plate is zinc plated steel. Includes rest position for plunger to stay in retracted position.

There is also a good range of Plungers - Indexing - Locking - With Mounting Plate - Steel on the Small Parts and Bearings website.


Plungers - Indexing - Locking - With Shoulder - Stainless Steel
Plungers - Indexing - Locking - With Shoulder - Stainless Steel

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.


There is also a good range of Plungers - Indexing - Locking - With Shoulder - Stainless Steel on the Small Parts and Bearings website.


Plungers - Indexing - Locking - With Shoulder - Steel
Plungers - Indexing - Locking - With Shoulder - Steel

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.

Body and pin are steel with black oxide finish.

There is also a good range of Plungers - Indexing - Locking - With Shoulder - Steel on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur G - Flanged
Bushes - Plastic - Iglidur G - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur G - Flanged on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur G - Unflanged
Bushes - Plastic - Iglidur G - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur G - Unflanged on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur H - Flanged
Bushes - Plastic - Iglidur H - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Underwater performance. High Temp. Chemical Resistance.

Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 175 Mpa. Hardness 87 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur H - Flanged on the Small Parts and Bearings website.


Bushes - Plastic - Iglidur H - Unflanged
Bushes - Plastic - Iglidur H - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Underwater performance. High Temp. Chemical Resistance.

Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 175 Mpa. Hardness 87 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

There is also a good range of Bushes - Plastic - Iglidur H - Unflanged on the Small Parts and Bearings website.


Plungers - Indexing - Non Locking - Stainless Steel
Plungers - Indexing - Non Locking - Stainless Steel

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.


There is also a good range of Plungers - Indexing - Non Locking - Stainless Steel on the Small Parts and Bearings website.


Plungers - Indexing - Non Locking - Steel
Plungers - Indexing - Non Locking - Steel

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.

Body and pin are steel with black oxide finish.

There is also a good range of Plungers - Indexing - Non Locking - Steel on the Small Parts and Bearings website.


Plungers - Indexing - Non Locking - With Knob - 303 Stainless Steel
Plungers - Indexing - Non Locking - With Knob - 303 Stainless Steel

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.

303 Stainless Steel.

There is also a good range of Plungers - Indexing - Non Locking - With Knob - 303 Stainless Steel on the Small Parts and Bearings website.


Plungers - Indexing - Non Locking - With Knob - Steel
Plungers - Indexing - Non Locking - With Knob - Steel

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.

Body and pin are steel with black oxide finish.

There is also a good range of Plungers - Indexing - Non Locking - With Knob - Steel on the Small Parts and Bearings website.


Plungers - Indexing - Non Locking - With Mounting Plate - Steel
Plungers - Indexing - Non Locking - With Mounting Plate - Steel

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.

Spring loaded to work in a variety of applications on both tooling and equipment that require surface mounting. Plunger is hardened and ground. Knob is black matte plastic. Mounting plate is zinc plated steel.

There is also a good range of Plungers - Indexing - Non Locking - With Mounting Plate - Steel on the Small Parts and Bearings website.


Plungers - Indexing - Non Locking - Without Knob - 303 Stainless Steel
Plungers - Indexing - Non Locking - Without Knob - 303 Stainless Steel

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.

303 Stainless Steel.

There is also a good range of Plungers - Indexing - Non Locking - Without Knob - 303 Stainless Steel on the Small Parts and Bearings website.


Plungers - Indexing - Non Locking - Without Knob - Steel
Plungers - Indexing - Non Locking - Without Knob - Steel

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.

Body and pin are steel with black oxide finish.

There is also a good range of Plungers - Indexing - Non Locking - Without Knob - Steel on the Small Parts and Bearings website.


Plungers - Indexing - Non Locking - With Shoulder - Stainless - With Knob
Plungers - Indexing - Non Locking - With Shoulder - Stainless - With Knob

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.


There is also a good range of Plungers - Indexing - Non Locking - With Shoulder - Stainless - With Knob on the Small Parts and Bearings website.


Plungers - Indexing - Non Locking - With Shoulder - Steel - With Knob
Plungers - Indexing - Non Locking - With Shoulder - Steel - With Knob

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.

Body and pin are steel with black oxide finish.

There is also a good range of Plungers - Indexing - Non Locking - With Shoulder - Steel - With Knob on the Small Parts and Bearings website.


Plungers - Indexing - Non Locking - With Shoulder - Steel - Without Knob
Plungers - Indexing - Non Locking - With Shoulder - Steel - Without Knob

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.

Body and pin are steel with black oxide finish.

There is also a good range of Plungers - Indexing - Non Locking - With Shoulder - Steel - Without Knob on the Small Parts and Bearings website.


Plungers - Indexing - Precision - Locking - Ball Grip
Plungers - Indexing - Precision - Locking - Ball Grip

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.


There is also a good range of Plungers - Indexing - Precision - Locking - Ball Grip on the Small Parts and Bearings website.


Plungers - Spring - L Handle - Locking - Stainless
Plungers - Spring - L Handle - Locking - Stainless

Also see combined categories:
All Threaded Spring Plungers
All Handled Spring Plungers

Items shown with Long-Lok have a dry threadlocking sealant applied to thread.

There is also a good range of Plungers - Spring - L Handle - Locking - Stainless on the Small Parts and Bearings website.


Plungers - Spring - L Handle - Locking - Stainless-Acetal
Plungers - Spring - L Handle - Locking - Stainless-Acetal

Also see combined categories:
All Threaded Spring Plungers
All Handled Spring Plungers

Stainless body with acetal nose

Items shown with Long-Lok have a dry threadlocking sealant applied to thread.

There is also a good range of Plungers - Spring - L Handle - Locking - Stainless-Acetal on the Small Parts and Bearings website.


Plungers - Spring - L Handle - Locking - Stainless-Phenolic
Plungers - Spring - L Handle - Locking - Stainless-Phenolic

Also see combined categories:
All Threaded Spring Plungers
All Handled Spring Plungers

Stainless body with phenolic nose

Items shown with Long-Lok have a dry threadlocking sealant applied to thread.

There is also a good range of Plungers - Spring - L Handle - Locking - Stainless-Phenolic on the Small Parts and Bearings website.


Plungers - Spring - L Handle - Locking - Steel
Plungers - Spring - L Handle - Locking - Steel

Also see combined categories:
All Threaded Spring Plungers
All Handled Spring Plungers

Items shown with Long-Lok have a dry threadlocking sealant applied to thread.

There is also a good range of Plungers - Spring - L Handle - Locking - Steel on the Small Parts and Bearings website.


Plungers - Spring - L Handle - Locking - Steel-Acetal
Plungers - Spring - L Handle - Locking - Steel-Acetal

Also see combined categories:
All Threaded Spring Plungers
All Handled Spring Plungers

Steel body and acetal nose

Items shown with Long-Lok have a dry threadlocking sealant applied to thread.

There is also a good range of Plungers - Spring - L Handle - Locking - Steel-Acetal on the Small Parts and Bearings website.


Plungers - Spring - L Handle - Locking - Steel-Phenolic
Plungers - Spring - L Handle - Locking - Steel-Phenolic

Also see combined categories:
All Threaded Spring Plungers
All Handled Spring Plungers

Steel body with phenolic nose

Items shown with Long-Lok have a dry threadlocking sealant applied to thread.

There is also a good range of Plungers - Spring - L Handle - Locking - Steel-Phenolic on the Small Parts and Bearings website.


Pins - Clevis - Self Locking
Pins - Clevis - Self Locking

Also see combined categories:
All Ball Lock Pins
All Clevis Pins

No need for cotter pins. Inexpensive ball lock pin type.

Self locking and reusable with a spring loaded ball lock. Plated steel with stainless steel ball.

Related Information:

There is also a good range of Pins - Clevis - Self Locking on the Small Parts and Bearings website.


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 125333 products in 2315 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 125333 products in 2315 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.