Latches Rotary Action Categories
Latches - Rotary Action - Link Lock - Keepers
Required for link lock rotary action latches. Match keeper with correct latch from selection.
There is also a good range of Latches - Rotary Action - Link Lock - Keepers on the Small Parts and Bearings website.
Latches - Rotary Action - Link Lock - Rivetted - Stainless
Lift and rotate wing to operate.
Keepers not included and must be purchased separately.
Related Information:
There is also a good range of Latches - Rotary Action - Link Lock - Rivetted - Stainless on the Small Parts and Bearings website.
You may also be interested in
Latches Slam Action
Latches - Slam Action - Slide
Fast snap in installation. Made from non-corrosive materials, black ABS plastic and stainless steel spring. Push to close latching.
There is also a good range of Latches - Slam Action - Slide on the Small Parts and Bearings website.
Catches - Rotary
Polyacetal catch and strike with polyethylene rollers. Ideal in corrosive environments.
There is also a good range of Catches - Rotary on the Small Parts and Bearings website.
Latches - 1-4 Turn - Simple
With 5.08mm offset cam. Cam may be reversed for increased grip range. Includes detent in body which signals positive open or closed position.
The catch on these latches may be supplied either standard, inverted or flat depending on the grip range. Catches are not reversible.
There is also a good range of Latches - 1-4 Turn - Simple on the Small Parts and Bearings website.
Latches - 1-4 Turn -Tee Handle - Non Locking
Quarter turn latches. Nema 4 and IP65 rated. Supplied assembled. Includes housing, insert, rubber seal, gasket, hex nut and cam.
Heavy Duty. Grip range is approximate and calculated as the door flange with compressed gasket and cabinet flange. Black polyamide handle. The catch on these latches may be supplied either standard, inverted or flat depending on the grip range. Catches are not reversible.
There is also a good range of Latches - 1-4 Turn -Tee Handle - Non Locking on the Small Parts and Bearings website.
Latches - Compression - Lift and Turn - Straight Handle
Lift handle to relax compression and then turn to open. Handle and sleeve are die cast zinc with either polished chrome or black powder coat finish.
Comes with mounting hardware. Max working load 44kg. M5 mounting screws supplied. For panels thicker than 6.35mm a longer screw and lockwasher combination will be required.
There is also a good range of Latches - Compression - Lift and Turn - Straight Handle on the Small Parts and Bearings website.
Latches - Draw - Over Centre - 300 Grade Stainless Steel
Passivated stainless steel. Latches mount with M4 screws, No. 8 screws or 5/32 rivets. Type B keeper uses a countersunk screw.
Keepers included. Type SC-97533 has a hole for a padlock.
There is also a good range of Latches - Draw - Over Centre - 300 Grade Stainless Steel on the Small Parts and Bearings website.
Latches - Draw - T-Handle - Stainless Steel
Black rubber T Handle with stainless steel bracket and keeper. Shipped assembled. Installs with 4.8mm rivets (3/16 in.) or 10 Gauge Screws. Can be welded. Keeper included.
There is also a good range of Latches - Draw - T-Handle - Stainless Steel on the Small Parts and Bearings website.
Latches - 110 Series - Adjustable Grip
Ultimate strength 145kg. Working strength 120kg.
Strike needs to be ordered separately.
There is also a good range of Latches - 110 Series - Adjustable Grip on the Small Parts and Bearings website.
Latches - 200 Series - Heavy Duty
Ultimate strength 660kg. Working strength 265kg.
Heavy Duty.
There is also a good range of Latches - 200 Series - Heavy Duty on the Small Parts and Bearings website.
Tools - Rotary Files - Aluminium Cut
Used for deburring and smoothing metals.
Made from Heat treated steel.
There is also a good range of Tools - Rotary Files - Aluminium Cut on the Small Parts and Bearings website.
Tools - Rotary Files - Double Cut
Used for deburring and smoothing metals.
Made from Heat treated steel.
There is also a good range of Tools - Rotary Files - Double Cut on the Small Parts and Bearings website.
Tools - Rotary Files - Standard Cut
Used for deburring and smoothing metals.
Made from Heat treated steel.
There is also a good range of Tools - Rotary Files - Standard Cut on the Small Parts and Bearings website.
Dampers - Rotary - 2.0 to 3.0 Ncm
Rotary dampers enable products to function with a smooth mechanical motion. Prevent lid and access panel closure damage.
Body: Polycarbonate / Gear: Polyacetal. Fluid: Silicone. Temp range 0 to 50 oC.
There is also a good range of Dampers - Rotary - 2.0 to 3.0 Ncm on the Small Parts and Bearings website.
Dampers - Rotary - 5.0 to 15.0 Ncm
Rotary dampers enable products to function with a smooth mechanical motion. Prevent lid and access panel closure damage.
Body: Polycarbonate / Gear: Polyacetal. Fluid: Silicone. Temp range 0 to 50 oC.
There is also a good range of Dampers - Rotary - 5.0 to 15.0 Ncm on the Small Parts and Bearings website.
Dampers - Rotary - 50 to 400 Ncm
Rotary dampers enable products to function with a smooth mechanical motion. Prevent lid and access panel closure damage.
Body: Polycarbonate. Temp range 0 to 50 oC. Weight: Max 120 grams.
There is also a good range of Dampers - Rotary - 50 to 400 Ncm on the Small Parts and Bearings website.
Handles - Tee
Zinc plated steel 7.94mm (5/16in.) square shank.
There is also a good range of Handles - Tee on the Small Parts and Bearings website.
Bushings - Stroke Rotary - Miniature
2 to 12mm Shaft Sizes. Can operate in both linear and rotary directions at the same time.
Set includes outer ring, ball cage and shaft. Ball Cage: Brass Balls: Hard Steel / Shaft: Hard Steel Outer Ring: Hard Steel. Temperature: +100oC (Constant), +120oC (Maximum). Stroke: = (L1 - Lb) x 2. Supplied with extreme accuracy with zero to minimum preload.
Related Information:
There is also a good range of Bushings - Stroke Rotary - Miniature on the Small Parts and Bearings website.
Handles - Latching - Padlocking
Zinc finished iron/steel construction. Has 5/16in. Square shank.
There is also a good range of Handles - Latching - Padlocking on the Small Parts and Bearings website.
Plungers - Indexing - Cam Action Mounting Blocks
Used with cam action indexing plungers
Mounting blocks are made from steel with black oxide finish.
Related Information:
There is also a good range of Plungers - Indexing - Cam Action Mounting Blocks on the Small Parts and Bearings website.
Plungers - Indexing - Cam Action - With Hex Nut
Used in many tooling applications as well as on many types of machinery and equipment.
Plunger is retracted as the nadle is turned on the cam of the body. Groove on top of cam locks the plunger into retracted position. Body made from black oxide coated steel. Plunger is made from steel, ground and nitrided.
Related Information:
There is also a good range of Plungers - Indexing - Cam Action - With Hex Nut on the Small Parts and Bearings website.
Plungers - Indexing - Cam Action - Without Hex Nut
Used in many tooling applications as well as on many types of machinery and equipment.
Plunger is retracted as the nadle is turned on the cam of the body. Groove on top of cam locks the plunger into retracted position. Body made from black oxide coated steel. Plunger is made from steel, ground and nitrided.
Related Information:
There is also a good range of Plungers - Indexing - Cam Action - Without Hex Nut on the Small Parts and Bearings website.
Handles - Latching - Cab Locks
Zinc finished steel. Accepts 5/16 in. square shank. Inside handle, right or left hand. Picture shown is right hand.
There is also a good range of Handles - Latching - Cab Locks on the Small Parts and Bearings website.
Strikes - Toggle Latch - Steel
Used with toggle latches series 800, 802, 803 and 806
There is also a good range of Strikes - Toggle Latch - Steel on the Small Parts and Bearings website.
Handles - Latching - L-Handle - Locking
Chrome finished zinc die-cast construction. 360o handle rotation. Comes with gasket. All locks are keyed alike. Keys included. May be used with rod kit for 2 point locking.
Related Information:
There is also a good range of Handles - Latching - L-Handle - Locking on the Small Parts and Bearings website.
Handles - Latching - T-Handle - Folding
Gold zinc finished steel. Die cast construction. 5/16in. Square shank. 360o rotation. Blind mount. Padlockable.
There is also a good range of Handles - Latching - T-Handle - Folding on the Small Parts and Bearings website.
Handles - Latching - T-Handle - Locking
90o clockwise rotation. Made of weatherable black nylon handle and steel parts. Includes one key. All locks keyed alike. May be used with rod kit for 2 point locking.
Related Information:
There is also a good range of Handles - Latching - T-Handle - Locking on the Small Parts and Bearings website.
Latching Handles - Outside Door - Heavy Duty
Black Glass Filled Polyamide Bezel, catch and Plug. Brass Shaft. Zinc plated mild steel fixing.
There is also a good range of Latching Handles - Outside Door - Heavy Duty on the Small Parts and Bearings website.
Handles - Latching - 2-Point Locking Rod Kit
Kit can be used with any 5/16in. Square shanked handles for two point locking. Kit includes two gold zinc plated steel rods, two plastic rod guides, steel cam, two steel bushings, two wave washers and three set screws.
There is also a good range of Handles - Latching - 2-Point Locking Rod Kit on the Small Parts and Bearings website.
Ballscrew - Thomson Saginaw
Offer 90% efficiency converting rotary to linear motion with low coefficient of friction. Match all components within the Thomson Saginaw range only.
When replacing screws, hydraulics or pneumatics, they allow the use of smaller, less expensive drive motors and reduce the need for auxiliary equipment. Offer dependable accuracy and repeatability, Made off high quality alloy steel, hardened to Rockwell 56-60C.
There is also a good range of Ballscrew - Thomson Saginaw on the Small Parts and Bearings website.
Nuts - Hexagonal - Binx - Steel
The standard Binx's entire locking action is contained within the nut body which is no thicker than a standard full nut. The ingenious design incorporates two opposing cantilever type springs which lock onto the bolt with inward and downward pressure. May be removed and placed repeatedly with minimum thread wear.
There is also a good range of Nuts - Hexagonal - Binx - Steel on the Small Parts and Bearings website.
Catches - Snap In Style - Grabber -tm-
Fast economical installation.
Fits frames from 1.1 to 7.1mm thick. Installation hole size 15mm x 39.9mm. Push to close and pull to open. Spring loaded over centre action. Corrosion resistant black ABS with 303 stainless steel spring.
There is also a good range of Catches - Snap In Style - Grabber -tm- on the Small Parts and Bearings website.
Bumpers - Elastomer - Medium Energy Absorption - Low Reaction Force
Elastomer bumpers provide excellent resistance to chemicals and humidity. 20 times greater durability than urethane.
10 greater durability than rubber and 500 times greater than steel coiled springs. Maintains excellent resilience at extreme temperatures and remains flexible with no material degradation between -62 oC and +148 Deg C (-80 Deg F and +300 Deg F). Mounting screws not included.
There is also a good range of Bumpers - Elastomer - Medium Energy Absorption - Low Reaction Force on the Small Parts and Bearings website.
Magnets - Rare Earth - Plated
Incredibly strong attraction and repulsion. Neodymium-Iron-Boron encased in nickel jackets to protect the brittle magnet material and prevent corrosion.
High strength to weight ratios. Commonly used in miniature applications such as linear actuators, sensing applications, gyroscopes, flow meters, recording devices, pacemakers and alternators. Temperature range -73 oC to 93 oC. Size tolerances +/- 0.13.
There is also a good range of Magnets - Rare Earth - Plated on the Small Parts and Bearings website.
Catches - Compression Spring
Three internal compression springs supply up to 30kg of spring tension. Available as padlockable or with secondary catch.
Spring tension compensates for gasket set. Provides exact tension for water tight and air tight seals.
There is also a good range of Catches - Compression Spring on the Small Parts and Bearings website.
Catches - Draw Pull
Draw pull catches are available in either steel or 304 stainless. Strike is included.
There is also a good range of Catches - Draw Pull on the Small Parts and Bearings website.
Catches - Knuckle
Strong and light polyacetal and polyamide. Holds cabinets secure with 7kg of pull force.
There is also a good range of Catches - Knuckle on the Small Parts and Bearings website.
Catches - Magnetic - Screw On
Various styles - refer pictures
There is also a good range of Catches - Magnetic - Screw On on the Small Parts and Bearings website.
Catches - Magnetic - Ultra Thin - Heavy Duty
Ultra thin strong magnetic catch is perfect for tight areas. Has a full 4kg of magnetic force.
Related Information:
There is also a good range of Catches - Magnetic - Ultra Thin - Heavy Duty on the Small Parts and Bearings website.
Catches - Magnetic - Ultra Thin - Light Duty
Ultra thin strong magnetic catch is perfect for tight areas. Has 2.5 kg of magnetic force.
Related Information:
There is also a good range of Catches - Magnetic - Ultra Thin - Light Duty on the Small Parts and Bearings website.
Catches - Roller
304 Stainless Steel and Polyurethane
There is also a good range of Catches - Roller on the Small Parts and Bearings website.
Catches - Side Mount - Grabber -tm-
Mounts inside your enclosure. Installs either right or left side by inverting. Use 4 gauge screws or 1/8in (3.125mm) rivets to install.
There is also a good range of Catches - Side Mount - Grabber -tm- on the Small Parts and Bearings website.
Catches - Side Mount - With Microswitch - Grabber -tm-
Mounts inside your enclosure. Installs either right or left side by inverting. Use 4 gauge screws or 1/8in (3.125mm) rivets to install.
Switch is designed to operate as an indicator light or form part of a non-safety related logic circuit.
There is also a good range of Catches - Side Mount - With Microswitch - Grabber -tm- on the Small Parts and Bearings website.
Clamps - Lorenz
Patented quick clamp is ideal for door openings on bins, hoppers, tanks and manholes. T-Handle allows torque without tools. The one piece unit is made from highly polished 304 stainless steel.
Full 50.8mm adjustment. 180o pivot when disengaged leaving access doorway unobstructed. Will not loosen through vibration. Brackets supplied for easy installation.
There is also a good range of Clamps - Lorenz on the Small Parts and Bearings website.
Pins - Taper - Metric - Extractable - External Thread
Metric Sizes Tapered 1:50 and threaded externally for easy extraction.
DIN 7977. Mild Steel.
Related Information:
There is also a good range of Pins - Taper - Metric - Extractable - External Thread on the Small Parts and Bearings website.
Pins - Taper - Metric - Extractable - Internal Thread
Metric Sizes Tapered 1:50 and threaded internally for easy extraction.
DIN 7978. Mild Steel.
Related Information:
There is also a good range of Pins - Taper - Metric - Extractable - Internal Thread on the Small Parts and Bearings website.
Belts - Vee - 12.5 x 9.0mm - A-4L
12.5mm Top Width x 9.0mm Height.
Sizes are nominal and may vary slightly. Items marked as Fractional Horsepower are designed for general purrpose low horseposer applications such as laundry machines, home workshop tools, small fans and blowers, garage equipment, small metal and woodworking tools etc. Belts shown as Fractional Horsepower type should not be used with reverse side idlers.
Related Information:
There is also a good range of Belts - Vee - 12.5 x 9.0mm - A-4L on the Small Parts and Bearings website.
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Clearance Items List
Contact Us
Charity
Dental Bearings
Distributor Locations
China
Dowel Pins
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)
Miniature Bearings Australia offers 125388 products in 2307 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.
Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.
