Miniature Bearings Australia Pty Ltd

Latches Quarter Turn Categories


Latches - 1-4 Turn - Simple
Latches - 1-4 Turn - Simple


With 5.08mm offset cam. Cam may be reversed for increased grip range. Includes detent in body which signals positive open or closed position.

The catch on these latches may be supplied either standard, inverted or flat depending on the grip range. Catches are not reversible.

There is also a good range of Latches - 1-4 Turn - Simple on the Small Parts and Bearings website.


Latches - 1-4 Turn -Tee Handle - Non Locking
Latches - 1-4 Turn -Tee Handle - Non Locking

Also see combined categories:
All Quarter Turn Latches

Quarter turn latches. Nema 4 and IP65 rated. Supplied assembled. Includes housing, insert, rubber seal, gasket, hex nut and cam.

Heavy Duty. Grip range is approximate and calculated as the door flange with compressed gasket and cabinet flange. Black polyamide handle. The catch on these latches may be supplied either standard, inverted or flat depending on the grip range. Catches are not reversible.

There is also a good range of Latches - 1-4 Turn -Tee Handle - Non Locking on the Small Parts and Bearings website.


Latches - Compression - Lift and Turn - Straight Handle
Latches - Compression - Lift and Turn - Straight Handle


Lift handle to relax compression and then turn to open. Handle and sleeve are die cast zinc with either polished chrome or black powder coat finish.

Comes with mounting hardware. Max working load 44kg. M5 mounting screws supplied. For panels thicker than 6.35mm a longer screw and lockwasher combination will be required.

There is also a good range of Latches - Compression - Lift and Turn - Straight Handle on the Small Parts and Bearings website.


Catches - Straight Loop
Catches - Straight Loop


High strength overcentre catch and strike. Economical and compact. Available in plain steel, zinc plated or 304 stainless steel. With or without mounting holes. Strike is included. Dimensions are as mounted.

Tension can be increased by increasing distance between catch and strike.

There is also a good range of Catches - Straight Loop on the Small Parts and Bearings website.


Latches - Draw - Over Centre - 300 Grade Stainless Steel
Latches - Draw - Over Centre - 300 Grade Stainless Steel


Passivated stainless steel. Latches mount with M4 screws, No. 8 screws or 5/32 rivets. Type B keeper uses a countersunk screw.

Keepers included. Type SC-97533 has a hole for a padlock.

There is also a good range of Latches - Draw - Over Centre - 300 Grade Stainless Steel on the Small Parts and Bearings website.


Latches - Draw - T-Handle - Stainless Steel
Latches - Draw - T-Handle - Stainless Steel


Black rubber T Handle with stainless steel bracket and keeper. Shipped assembled. Installs with 4.8mm rivets (3/16 in.) or 10 Gauge Screws. Can be welded. Keeper included.


There is also a good range of Latches - Draw - T-Handle - Stainless Steel on the Small Parts and Bearings website.


Latches - 110 Series - Adjustable Grip
Latches - 110 Series - Adjustable Grip


Ultimate strength 145kg. Working strength 120kg.

Strike needs to be ordered separately.

There is also a good range of Latches - 110 Series - Adjustable Grip on the Small Parts and Bearings website.


Latches - 200 Series - Heavy Duty
Latches - 200 Series - Heavy Duty


Ultimate strength 660kg. Working strength 265kg.

Heavy Duty.

There is also a good range of Latches - 200 Series - Heavy Duty on the Small Parts and Bearings website.


Latches - Rotary Action - Link Lock - Keepers
Latches - Rotary Action - Link Lock - Keepers


Required for link lock rotary action latches. Match keeper with correct latch from selection.


There is also a good range of Latches - Rotary Action - Link Lock - Keepers on the Small Parts and Bearings website.


Latches - Rotary Action - Link Lock - Rivetted - Stainless
Latches - Rotary Action - Link Lock - Rivetted - Stainless


Lift and rotate wing to operate.

Keepers not included and must be purchased separately.

Related Information:

There is also a good range of Latches - Rotary Action - Link Lock - Rivetted - Stainless on the Small Parts and Bearings website.


Latches - Slam Action - Slide
Latches - Slam Action - Slide


Fast snap in installation. Made from non-corrosive materials, black ABS plastic and stainless steel spring. Push to close latching.


There is also a good range of Latches - Slam Action - Slide on the Small Parts and Bearings website.


Handles - Tee
Handles - Tee


Zinc plated steel 7.94mm (5/16in.) square shank.


There is also a good range of Handles - Tee on the Small Parts and Bearings website.


Handles - Latching - Padlocking
Handles - Latching - Padlocking


Zinc finished iron/steel construction. Has 5/16in. Square shank.


There is also a good range of Handles - Latching - Padlocking on the Small Parts and Bearings website.


Handles - Latching - Cab Locks
Handles - Latching - Cab Locks


Zinc finished steel. Accepts 5/16 in. square shank. Inside handle, right or left hand. Picture shown is right hand.


There is also a good range of Handles - Latching - Cab Locks on the Small Parts and Bearings website.


Strikes - Toggle Latch - Steel
Strikes - Toggle Latch - Steel


Used with toggle latches series 800, 802, 803 and 806


There is also a good range of Strikes - Toggle Latch - Steel on the Small Parts and Bearings website.


Handles - Latching - L-Handle - Locking
Handles - Latching - L-Handle - Locking


Chrome finished zinc die-cast construction. 360o handle rotation. Comes with gasket. All locks are keyed alike. Keys included. May be used with rod kit for 2 point locking.


Related Information:

There is also a good range of Handles - Latching - L-Handle - Locking on the Small Parts and Bearings website.


Handles - Latching - T-Handle - Folding
Handles - Latching - T-Handle - Folding

Also see combined categories:
All T Handles

Gold zinc finished steel. Die cast construction. 5/16in. Square shank. 360o rotation. Blind mount. Padlockable.


There is also a good range of Handles - Latching - T-Handle - Folding on the Small Parts and Bearings website.


Handles - Latching - T-Handle - Locking
Handles - Latching - T-Handle - Locking

Also see combined categories:
All T Handles

90o clockwise rotation. Made of weatherable black nylon handle and steel parts. Includes one key. All locks keyed alike. May be used with rod kit for 2 point locking.


Related Information:

There is also a good range of Handles - Latching - T-Handle - Locking on the Small Parts and Bearings website.


Latching Handles - Outside Door - Heavy Duty
Latching Handles - Outside Door - Heavy Duty


Black Glass Filled Polyamide Bezel, catch and Plug. Brass Shaft. Zinc plated mild steel fixing.

There is also a good range of Latching Handles - Outside Door - Heavy Duty on the Small Parts and Bearings website.


Handles - Latching - 2-Point Locking Rod Kit
Handles - Latching - 2-Point Locking Rod Kit


Kit can be used with any 5/16in. Square shanked handles for two point locking. Kit includes two gold zinc plated steel rods, two plastic rod guides, steel cam, two steel bushings, two wave washers and three set screws.


There is also a good range of Handles - Latching - 2-Point Locking Rod Kit on the Small Parts and Bearings website.


Screws - Thumb - Half Turn
Screws - Thumb - Half Turn

Also see combined categories:
All Thumb Screws


There is also a good range of Screws - Thumb - Half Turn on the Small Parts and Bearings website.


Screws - Thumb - 1-4 Turn
Screws - Thumb - 1-4 Turn

Also see combined categories:
All Thumb Screws


There is also a good range of Screws - Thumb - 1-4 Turn on the Small Parts and Bearings website.


Sleeves - Hex Hole - Carbon Steel
Sleeves - Hex Hole - Carbon Steel

Also see combined categories:
All Hex Hole Sleeves

Carefully turned to provide 0.076mm (0.003in) concentricity ID to OD. Round OD with with a uniform hex hole broached from one end to the other.


There is also a good range of Sleeves - Hex Hole - Carbon Steel on the Small Parts and Bearings website.


Knobs - Three Lobe - Safety - Male
Knobs - Three Lobe - Safety - Male

Also see combined categories:
All Lobe Knobs
All Knobs

Knob only turns when pressed downwards and turned simultaneously to avoid involuntary turning. Also see star knobs


There is also a good range of Knobs - Three Lobe - Safety - Male on the Small Parts and Bearings website.


Sleeves - Hex Hole - Hardened
Sleeves - Hex Hole - Hardened

Also see combined categories:
All Hex Hole Sleeves

Pre hardened to Rockwell 23-30C. Carefully turned to provide 0.076mm (0.003in) concentricity ID to OD. Round OD with with a uniform hex hole broached from one end to the other.


There is also a good range of Sleeves - Hex Hole - Hardened on the Small Parts and Bearings website.


Pulleys - Blocks - Eye - Swivel
Pulleys - Blocks - Eye - Swivel

Also see combined categories:
All Pulley Blocks

Steel side plates. Electroplated sheaves are turned from cold rolled bar stock.

Bearings made from bronze and steel, oil impregnated for self lubrication. Designed for high load and medium speed.

There is also a good range of Pulleys - Blocks - Eye - Swivel on the Small Parts and Bearings website.


Rod - Drill Blanks
Rod - Drill Blanks

Also see combined categories:
All Silver Steel Drill Blanks
All Drill Rod

Made of hardened high speed steel.

Useful for turning and boring tools, constructing pins, hinge pins, arbors, pin gauges, dowels, preforating punchs. Can also be ground to make special cutting tools such as mills, spotfaces, angle or radii cutters, etc.

There is also a good range of Rod - Drill Blanks on the Small Parts and Bearings website.


Pulleys - Blocks - Flat
Pulleys - Blocks - Flat

Also see combined categories:
All Pulley Blocks

Steel side plates with drop forged hooks. Electroplated sheaves are turned from cold rolled bar stock.

Bearings made from bronze and steel, oil impregnated for self lubrication. Designed for high load and medium speed.

There is also a good range of Pulleys - Blocks - Flat on the Small Parts and Bearings website.


Bearings - One Way - Sprag - Standard
Bearings - One Way - Sprag - Standard

Also see combined categories:
All One Way Clutch Bearings

Sprag clutch bearings allow your application to turn one way whilst locking in the opposite direction.

Designed for press fit installation. Correct interference dimensions must be maintained to obtain maximum bearing and clutch performance. Mount the clutch ensuring that the shaft drive directionis in the direction indicated by the arrow on the inner race. To install, use a press tool / do not hammer or apply other stock to clutch. Make sure housing has enough strength to withstand press required for fitting installation. High carbon hardened steel alloy. Always lock out power switch before installing, removing, lubricating or servicing a system that uses Cam Clutch products. When connecting or disconnecting Cam Clutch products, eye protection is required. Wear safety glasses, protective clothing, gloves and safety shoes.

Related Information:

There is also a good range of Bearings - One Way - Sprag - Standard on the Small Parts and Bearings website.


Pulleys - Blocks - Eye - Fixed
Pulleys - Blocks - Eye - Fixed

Also see combined categories:
All Pulley Blocks

Steel side plates with drop forged hooks. Electroplated sheaves are turned from cold rolled bar stock.

Bearings made from bronze and steel, oil impregnated for self lubrication. Designed for high load and medium speed.

There is also a good range of Pulleys - Blocks - Eye - Fixed on the Small Parts and Bearings website.


Switches - Rocker
Switches - Rocker

Also see combined categories:
All Switches

20mm Diameter mounting hole 12V/10amp. On/Off Round Switches with Housing. Illuminates when turned to on position.

Switchs are rated at 10amp @ 600VAC with finger safe screw terminals.

There is also a good range of Switches - Rocker on the Small Parts and Bearings website.


Rings - Hoist - Side Pull - Full Swivel
Rings - Hoist - Side Pull - Full Swivel

Also see combined categories:
All Hoist Rings

Full swivel and pivot action allows you to flip and turn parts without unhooking. Extra large diameter ring allows for large hook. Made of alloy steel with black oxide finish. Safety factor of 5 to 1.

Individually pull tested and certified.

There is also a good range of Rings - Hoist - Side Pull - Full Swivel on the Small Parts and Bearings website.


Rings - Hoist - Tamper Resistant - Swivel Eybolts - Steel
Rings - Hoist - Tamper Resistant - Swivel Eybolts - Steel

Also see combined categories:
All Hoist Rings

Full swivel and pivot action allows you to flip and turn parts without unhooking. Made of alloy steel with black oxide finish. Tamper resistant design is ideal for permanent mounting on OEM applications or on moulds, dies and fixtures.

safety factor of 5 to 1. Installation tool sold separately.

Related Information:

There is also a good range of Rings - Hoist - Tamper Resistant - Swivel Eybolts - Steel on the Small Parts and Bearings website.


Rings - Hoist - Tamper Resistant - Swivel Eybolts - Stainless Steel
Rings - Hoist - Tamper Resistant - Swivel Eybolts - Stainless Steel

Also see combined categories:
All Hoist Rings

Full swivel and pivot action allows you to flip and turn parts without unhooking. Made of 316 stainless steel. Tamper resistant design is ideal for permanent mounting on OEM applications or on moulds, dies and fixtures.

safety factor of 5 to 1. Installation tool sold separately.

Related Information:

There is also a good range of Rings - Hoist - Tamper Resistant - Swivel Eybolts - Stainless Steel on the Small Parts and Bearings website.


Bearings - Thrust - Ball - Grooved - Chrome Steel
Bearings - Thrust - Ball - Grooved - Chrome Steel

Also see combined categories:
All Ball Thrust Bearings

3 Piece Thrust Bearings Open Type

These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.

Related Information:

There is also a good range of Bearings - Thrust - Ball - Grooved - Chrome Steel on the Small Parts and Bearings website.


Bearings - Thrust - Ball - Grooved - Stainless Steel
Bearings - Thrust - Ball - Grooved - Stainless Steel

Also see combined categories:
All Ball Thrust Bearings

3 Piece Thrust Bearings Open Type

These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.

Related Information:

There is also a good range of Bearings - Thrust - Ball - Grooved - Stainless Steel on the Small Parts and Bearings website.


Rollers - Solid - Stud Mount - Coloured Urethane
Rollers - Solid - Stud Mount - Coloured Urethane

Also see combined categories:
All Solid Stud Mount Rollers

Used on conveyors, belt idlers, shock cushioners, stamping die part guides, supports etc.

Blue colour may turn a shade of green when exposed to UV lighting. Designed for use in machines and assembly operations where part movement and protection is needed. Complete with washer and locknut. Free idling with ball bearings.

There is also a good range of Rollers - Solid - Stud Mount - Coloured Urethane on the Small Parts and Bearings website.


Hooks - Lifting - Swivel and Pivot
Hooks - Lifting - Swivel and Pivot


Full swivel and 180o pivot with double ball bearings for smooth tilting, twisting and turning.

Eliminates jerking of the lifting point. Suitable for sling system including hook, eye or loop. Has non protruding hook tip and is extremely durable. Forged safety latch which engages in the top of the hook protecting against lateral bending. Coiled double leg stainless steel spring protected by latch design.

There is also a good range of Hooks - Lifting - Swivel and Pivot on the Small Parts and Bearings website.


Bearings - Thrust - Ball - Flat - Chrome Steel
Bearings - Thrust - Ball - Flat - Chrome Steel

Also see combined categories:
All Ball Thrust Bearings

3 Piece Thrust Bearings Open Type with Flat Washers

These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.

Related Information:

There is also a good range of Bearings - Thrust - Ball - Flat - Chrome Steel on the Small Parts and Bearings website.


Bearings - Thrust - Ball - Flat - Stainless Steel
Bearings - Thrust - Ball - Flat - Stainless Steel

Also see combined categories:
All Ball Thrust Bearings

3 Piece Thrust Bearings Open Type with Flat Washers

These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.

Related Information:

There is also a good range of Bearings - Thrust - Ball - Flat - Stainless Steel on the Small Parts and Bearings website.


Plungers - Indexing - Cam Action - With Hex Nut
Plungers - Indexing - Cam Action - With Hex Nut

Also see combined categories:
All Indexing Plungers

Used in many tooling applications as well as on many types of machinery and equipment.

Plunger is retracted as the nadle is turned on the cam of the body. Groove on top of cam locks the plunger into retracted position. Body made from black oxide coated steel. Plunger is made from steel, ground and nitrided.

Related Information:

There is also a good range of Plungers - Indexing - Cam Action - With Hex Nut on the Small Parts and Bearings website.


Plungers - Indexing - Cam Action - Without Hex Nut
Plungers - Indexing - Cam Action - Without Hex Nut

Also see combined categories:
All Indexing Plungers

Used in many tooling applications as well as on many types of machinery and equipment.

Plunger is retracted as the nadle is turned on the cam of the body. Groove on top of cam locks the plunger into retracted position. Body made from black oxide coated steel. Plunger is made from steel, ground and nitrided.

Related Information:

There is also a good range of Plungers - Indexing - Cam Action - Without Hex Nut on the Small Parts and Bearings website.


Inserts - Thread Repair - Helicoil Extracting Tools
Inserts - Thread Repair - Helicoil Extracting Tools


Extracting tools are used to remove helicoil inserts. This is done by applying the tool to the insert, striking the tools head and turning it counter-clockwide.


There is also a good range of Inserts - Thread Repair - Helicoil Extracting Tools on the Small Parts and Bearings website.


Spiral Rings - External - Medium-Heavy Duty
Spiral Rings - External - Medium-Heavy Duty

Also see combined categories:
All External Spiral Rings

AME / WST / RST - Spring Steel and Stainless Steel.

Originally designed to fit NAS50-51 grooves, this series is a popular OEM specification. This two/three turn design is easier to install than the heavy duty RRN option. Equivalent to Associated Spring: AME, Smalley: WST, Spirolox and Ramsey: RST.

There is also a good range of Spiral Rings - External - Medium-Heavy Duty on the Small Parts and Bearings website.


Dual Vee - Adaptor Bushings
Dual Vee - Adaptor Bushings

Also see combined categories:
All Dual Vee Guide Wheels

Vee grooved track roller bushings.

Stationary bushings have a concentric hole. Adjustable bushings have an eccentric hole allowing positioning of the guide wheel as the bush is turned.

Related Information:

There is also a good range of Dual Vee - Adaptor Bushings on the Small Parts and Bearings website.


Rollers - Feed - With Aluminium Sleeve
Rollers - Feed - With Aluminium Sleeve

Also see combined categories:
All Rollers

Tolerance of Roller Outside Diameter (D) is +/-0.075 mm

Urethane 60 Durometer ground outside diameter. Aluminium sleeve. Feed rollers do not have a rotating bore. They are designed to turn with the shaft.

Related Information:

There is also a good range of Rollers - Feed - With Aluminium Sleeve on the Small Parts and Bearings website.


Bearings - Thrust - Ball - Grooved - ZRO2 Ceramic
Bearings - Thrust - Ball - Grooved - ZRO2 Ceramic

Also see combined categories:
All Ball Thrust Bearings

3 Piece Thrust Bearings Open Type. Excellent performance in electrical and magnetism sensitive applications. Full ceramic silicon nitride.

These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.

Related Information:

There is also a good range of Bearings - Thrust - Ball - Grooved - ZRO2 Ceramic on the Small Parts and Bearings website.


Spiral Rings - Internal - Medium-Heavy Duty
Spiral Rings - Internal - Medium-Heavy Duty

Also see combined categories:
All Internal Spiral Rings

Includes Series AMI / WHT / Spirolox RRT - Spring Steel and Stainless Steel.

Originally designed to fit NAS50-51 grooves, this series is a popular OEM specification. This two/three turn design is easier to install than the heavy duty RRN option. Equivalent to Associated Spring: AMI, Smalley: WHT, Spirolox and Ramsey: RRT.

There is also a good range of Spiral Rings - Internal - Medium-Heavy Duty on the Small Parts and Bearings website.


Rollers - Solid - Shaft Mount - Coloured Urethane
Rollers - Solid - Shaft Mount - Coloured Urethane

Also see combined categories:
All Solid Shaft Mount Rollers

Used on conveyors, belt idlers, shock cushioners, stamping die part guides, supports etc.

Designed for use in machines and assembly operations where part movement and protection is needed. Blue colour may turn a shade of green when exposed to UV lighting.

There is also a good range of Rollers - Solid - Shaft Mount - Coloured Urethane on the Small Parts and Bearings website.


Rollers - Solid - Bonded to Steel Insert - Coloured Urethane
Rollers - Solid - Bonded to Steel Insert - Coloured Urethane

Also see combined categories:
All Solid Rollers with Insert

Used on conveyors, belt idlers, shock cushioners, stamping die part guides, supports etc.

Designed for use in machines and assembly operations where part movement and protection is needed. Blue colour may turn a shade of green when exposed to UV lighting.

There is also a good range of Rollers - Solid - Bonded to Steel Insert - Coloured Urethane on the Small Parts and Bearings website.


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 122545 products in 2631 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 122545 products in 2631 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.