Miniature Bearings Australia Pty Ltd

IDLER SHAFT


Category Matches

Shafting Precision Ground


Shafts - Idler
Shafts - Idler


Ready made precision ground idler shafts.

Internal grease hole can be accessed by drilling if required. Use with your idler pulleys. Can be used with the idler tensioners listed on this site or use in your own design.

Related Information:

There is also a good range of Shafts - Idler on the Small Parts and Bearings website.


Tensioners


Tensioner - Adjustable Screw
Tensioner - Adjustable Screw

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Uses a screw adjustment for positive precise tensioning.

Idler shaft and pulleys not included with tensioner.

Related Information:

There is also a good range of Tensioner - Adjustable Screw on the Small Parts and Bearings website.


Tensioner - Drive - Single Adjusting - Shaft Mount
Tensioner - Drive - Single Adjusting - Shaft Mount

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Mounts on any free point of a fixed shaft allowing controlled tensioning around 360o.

Idler shaft and pulleys not included with tensioner.

Related Information:

There is also a good range of Tensioner - Drive - Single Adjusting - Shaft Mount on the Small Parts and Bearings website.


Tensioner - Fixed Angle
Tensioner - Fixed Angle

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Can be mounted on top of any flat surface to provide horizontal tenaioning.

Idler shaft and pulleys not included with tensioner.

Related Information:

There is also a good range of Tensioner - Fixed Angle on the Small Parts and Bearings website.


Tensioner - Fixed Flanged
Tensioner - Fixed Flanged

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Compact design allows mounting where space is limited.

Idler shaft and pulleys not included with tensioner.

Related Information:

There is also a good range of Tensioner - Fixed Flanged on the Small Parts and Bearings website.


Tensioner - Horizontal Mount
Tensioner - Horizontal Mount

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Has 88.9mm travel and is mounted 90o to the length of the part. Both ends are tapped so the shaft can be threaded on either side of the tensioner.

Idler shaft and pulleys not included with tensioner. Hole is tapped to accept 38.1mm diameter idler shaft (ordered separately).

Related Information:

There is also a good range of Tensioner - Horizontal Mount on the Small Parts and Bearings website.


Tensioner - Vertical Mount
Tensioner - Vertical Mount

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Has 88.9mm travel through the use of the vertical slot. Head is drilled and tapped to accept 38.1mm diameter idler shaft (ordered separately).

Idler shaft and pulleys not included with tensioner.

Related Information:

There is also a good range of Tensioner - Vertical Mount on the Small Parts and Bearings website.


Rollers


Rollers - Durasoft - Shaft Mount - Black Neoprene
Rollers - Durasoft - Shaft Mount - Black Neoprene

Also see combined categories:
All Shaft Mount Durasoft Rollers

Used on conveyors, belt idlers, shock cushioners, stamping die part guides, supports etc.

Designed for use in machines and assembly operations where part movement and protection is needed. Durasoft rollers have a gentle but firm touch. Unique shape of holes adds to their soft but resilient nature.

There is also a good range of Rollers - Durasoft - Shaft Mount - Black Neoprene on the Small Parts and Bearings website.


Rollers - Durasoft - Shaft Mount - Coloured Urethane
Rollers - Durasoft - Shaft Mount - Coloured Urethane

Also see combined categories:
All Shaft Mount Durasoft Rollers

Used on conveyors, belt idlers, shock cushioners, stamping die part guides, supports etc.

Designed for use in machines and assembly operations where part movement and protection is needed. Durasoft rollers have a gentle but firm touch. Unique shape of holes adds to their soft but resilient nature. Blue colour may turn a shade of green when exposed to UV lighting.

There is also a good range of Rollers - Durasoft - Shaft Mount - Coloured Urethane on the Small Parts and Bearings website.


Rollers - Solid - Shaft Mount - Black Neoprene
Rollers - Solid - Shaft Mount - Black Neoprene

Also see combined categories:
All Solid Shaft Mount Rollers

Used on conveyors, belt idlers, shock cushioners, stamping die part guides, supports etc.

Designed for use in machines and assembly operations where part movement and protection is needed.

There is also a good range of Rollers - Solid - Shaft Mount - Black Neoprene on the Small Parts and Bearings website.


Rollers - Solid - Shaft Mount - Coloured Urethane
Rollers - Solid - Shaft Mount - Coloured Urethane

Also see combined categories:
All Solid Shaft Mount Rollers

Used on conveyors, belt idlers, shock cushioners, stamping die part guides, supports etc.

Designed for use in machines and assembly operations where part movement and protection is needed. Blue colour may turn a shade of green when exposed to UV lighting.

There is also a good range of Rollers - Solid - Shaft Mount - Coloured Urethane on the Small Parts and Bearings website.


Tensioners


Tensioner - Drive - Adjustable Angle
Tensioner - Drive - Adjustable Angle

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Fixed base with adjustable arm through 360o.

Idler shaft and pulleys not included with tensioner.

Related Information:

There is also a good range of Tensioner - Drive - Adjustable Angle on the Small Parts and Bearings website.


Tensioner - Drive - Adjustable Flanged
Tensioner - Drive - Adjustable Flanged

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. With flanged base that can be mounted in a tight area.

Idler shaft and pulleys not included with tensioner. Rotating arm gives operator 360o controlled tensioning. Serrated teeth to prevent slippage once tightened.

Related Information:

There is also a good range of Tensioner - Drive - Adjustable Flanged on the Small Parts and Bearings website.


Tensioner - Heavy Duty - Type 2
Tensioner - Heavy Duty - Type 2

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Has 152.4mm travel through the use of the adjusting slots. Head is drilled and tapped to accept 50.8mm diameter idler shaft (ordered separately).

Idler shaft and pulleys not included with tensioner. Shaft is mounted to the side at 90o and is anchored by set screws.

Related Information:

There is also a good range of Tensioner - Heavy Duty - Type 2 on the Small Parts and Bearings website.


Tensioner - Heavy Duty - Type 3
Tensioner - Heavy Duty - Type 3

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Has 152.4mm travel through the use of the adjusting slots. Head is drilled and tapped to accept 50.8mm diameter idler shaft (ordered separately).

Idler shaft and pulleys not included with tensioner. Shaft is mounted straight out from face and anchored by set screws. Shaft is located in the centre of the tensioner between the adjusting slots.

Related Information:

There is also a good range of Tensioner - Heavy Duty - Type 3 on the Small Parts and Bearings website.


Tensioner - Heavy Duty - Type 4
Tensioner - Heavy Duty - Type 4

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Has 152.4mm travel through the use of the adjusting slots. Head is drilled and tapped to accept 50.8mm diameter idler shaft (ordered separately).

Idler shaft and pulleys not included with tensioner. Shaft is mounted straight out from face and anchored by set screws. Adjusting slots are parallel to each other.

Related Information:

There is also a good range of Tensioner - Heavy Duty - Type 4 on the Small Parts and Bearings website.


Pulleys Idler


Pulleys - Timing - Idler
Pulleys - Timing - Idler

Also see combined categories:
All Idler Pulleys

Complete with Needle Roller Bearing.

Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners.

Related Information:

There is also a good range of Pulleys - Timing - Idler on the Small Parts and Bearings website.


Tensioners


Tensioner - Drive - Double Adjust - Base Mount
Tensioner - Drive - Double Adjust - Base Mount

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Adjusting slot assists with precise adjustments.

Idler shaft and pulleys not included with tensioner. Rotating arm gives operator 360o controlled tensioning. Serrated teeth to prevent slippage once tightened.

Related Information:

There is also a good range of Tensioner - Drive - Double Adjust - Base Mount on the Small Parts and Bearings website.


You may also be interested in

Chain and Sprockets Roller


Sprockets - Idler
Sprockets - Idler

Also see combined categories:
All Sprockets for Roller Chain

Complete with Needle Roller or Ball Bearings. 3.75mm to 25.4mm pitch.

Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners.

Related Information:

There is also a good range of Sprockets - Idler on the Small Parts and Bearings website.


Square Shaft


Shafting - Linear - Square
Shafting - Linear - Square



There is also a good range of Shafting - Linear - Square on the Small Parts and Bearings website.


Shafting Aluminium


Shafting - Aluminium
Shafting - Aluminium

Also see combined categories:
All Shafting
All Aluminium Shafting

Drylin aluminium shafting is recommended for use with Igubal Drylin bearings or Frelon lined bearings only.

Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: ph between 2 and 9.

There is also a good range of Shafting - Aluminium on the Small Parts and Bearings website.


Shafting - Aluminium - Ceramic Coated
Shafting - Aluminium - Ceramic Coated

Also see combined categories:
All Shafting
All Aluminium Shafting

Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.

Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated.

Related Information:

There is also a good range of Shafting - Aluminium - Ceramic Coated on the Small Parts and Bearings website.


Shafting - Aluminium - Ceramic Coated - Tapped
Shafting - Aluminium - Ceramic Coated - Tapped

Also see combined categories:
All Shafting
All Aluminium Shafting

Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.

Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated.

Related Information:

There is also a good range of Shafting - Aluminium - Ceramic Coated - Tapped on the Small Parts and Bearings website.


Shafting - Pipe - Aluminium
Shafting - Pipe - Aluminium

Also see combined categories:
All Pipe Shaft
All Metal Tube

Recommended for use with Igubal Drylin bearings only.

Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: Ph Greater than 2 and Less than 9.

There is also a good range of Shafting - Pipe - Aluminium on the Small Parts and Bearings website.


Shafting - Supported - Pre-Drilled - Aluminium
Shafting - Supported - Pre-Drilled - Aluminium

Also see combined categories:
All Shafting
All Aluminium Shafting

For Drylin Bearings.

Material : AlMgSi 0.5 F22. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Spec. Electr. Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: Ph Greater than 2 and less than 9.

There is also a good range of Shafting - Supported - Pre-Drilled - Aluminium on the Small Parts and Bearings website.


Shafting General Purpose


Shafting - Carbon Steel - Keyed
Shafting - Carbon Steel - Keyed

Also see combined categories:
All Shafting
All Steel Shafting

Keyways are cut full length of each bar. Low carbon steel C1018. Good case hardening properties.

Diameter Tolerance +0.00/-0.051. Keyway Depth Tolerance +0.41/-0.00. Keyway Width Tolerance +0.05/-0.00. Unhardened carbon steel. Special order may be available for stainless steel, other diameters, other lengths. Please ask.

There is also a good range of Shafting - Carbon Steel - Keyed on the Small Parts and Bearings website.


Shafting - Unground - Silver Steel
Shafting - Unground - Silver Steel

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

Unhardened silversteel shafting for general purposes. Not suitable for precision bearings until machined to correct tolerances and hardened.

See also drill rod. Drill Rod.

Related Information:

There is also a good range of Shafting - Unground - Silver Steel on the Small Parts and Bearings website.


Shafting Precision Ground


Shafting - Ground - Precision - Chrome Plated
Shafting - Ground - Precision - Chrome Plated


Precision ground shafting. AISI C1060 and chrome plated for corrosion resistance. Case hardened and recommended for use with precision bearings. Ends are not plated.

Case hardened to 60-65 Rockwell C. Chrome plated for corrosion resistance.

There is also a good range of Shafting - Ground - Precision - Chrome Plated on the Small Parts and Bearings website.


Shafting - Ground - Precision - High Carbon Steel
Shafting - Ground - Precision - High Carbon Steel

Also see combined categories:
All Shafting
All Steel Shafting

Precision ground shafting. AISI C1060. Hardened and recommended for use with precision bearings.


Related Information:

There is also a good range of Shafting - Ground - Precision - High Carbon Steel on the Small Parts and Bearings website.


Shafting - Ground - Precision - Stainless 303 Grade
Shafting - Ground - Precision - Stainless 303 Grade

Also see combined categories:
All Shafting
All Stainless Shafting

Precision ground shafting.


Related Information:

There is also a good range of Shafting - Ground - Precision - Stainless 303 Grade on the Small Parts and Bearings website.


Shafting - Ground - Precision - Stainless 416 Grade Hardened
Shafting - Ground - Precision - Stainless 416 Grade Hardened

Also see combined categories:
All Shafting
All Stainless Shafting

Precision ground shafting. 416 grade. Hardened and recommended for use with precision bearings.


Related Information:

There is also a good range of Shafting - Ground - Precision - Stainless 416 Grade Hardened on the Small Parts and Bearings website.


Shafting - Ground - Precision - Stainless 420 Grade Hardened
Shafting - Ground - Precision - Stainless 420 Grade Hardened

Also see combined categories:
All Shafting
All Stainless Shafting

Precision ground shafting. 420 grade. Hardened and recommended for use with precision bearings.


Related Information:

There is also a good range of Shafting - Ground - Precision - Stainless 420 Grade Hardened on the Small Parts and Bearings website.


Shafting - Ground - Precision - Stainless 440C Grade Hardened
Shafting - Ground - Precision - Stainless 440C Grade Hardened

Also see combined categories:
All Shafting
All Stainless Shafting

Precision ground shafting. 440C grade. Hardened and recommended for use with precision bearings.


Related Information:

There is also a good range of Shafting - Ground - Precision - Stainless 440C Grade Hardened on the Small Parts and Bearings website.


Shafting - Ground - Precision - Titanium - Ti-Gr2-TA1
Shafting - Ground - Precision - Titanium - Ti-Gr2-TA1

Also see combined categories:
All Shafting
All Titanium Shafting

CP2 Commercially Pure Titanium Grade 2. Tensile Strength 35.2 kgf/mm2. Yield Strength 28.2 kgf/mm2. Elongation 20 Percent.

Commercially pure for general industrial corrosion applications. UNS R50400. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.3, O 0.25, Ti Balance.

Related Information:

There is also a good range of Shafting - Ground - Precision - Titanium - Ti-Gr2-TA1 on the Small Parts and Bearings website.


Shafting - Ground - Precision - Titanium - Ti-Gr5 - TC4
Shafting - Ground - Precision - Titanium - Ti-Gr5 - TC4

Also see combined categories:
All Shafting
All Titanium Shafting

Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Related Information:

There is also a good range of Shafting - Ground - Precision - Titanium - Ti-Gr5 - TC4 on the Small Parts and Bearings website.


Shafting - Pre Drilled and Tapped - High Carbon Steel
Shafting - Pre Drilled and Tapped - High Carbon Steel

Also see combined categories:
All Shafting
All Steel Shafting

For use with rail supports and open linear bearings

Straightness: 0.1 mm / mtr.

There is also a good range of Shafting - Pre Drilled and Tapped - High Carbon Steel on the Small Parts and Bearings website.


Shafting - Pre Drilled and Tapped - Stainless Steel Steel
Shafting - Pre Drilled and Tapped - Stainless Steel Steel

Also see combined categories:
All Shafting
All Stainless Shafting

For use with rail supports and open linear bearings


There is also a good range of Shafting - Pre Drilled and Tapped - Stainless Steel Steel on the Small Parts and Bearings website.


Shafts - Pinion
Shafts - Pinion



There is also a good range of Shafts - Pinion on the Small Parts and Bearings website.


Shafting General Purpose


Shafts - Flexible - Panel Mount - Cased
Shafts - Flexible - Panel Mount - Cased

Also see combined categories:
All Flexible Panel Mount Shaft

See PDF file at bottom of internet page for Performance Data.

Related Information:

There is also a good range of Shafts - Flexible - Panel Mount - Cased on the Small Parts and Bearings website.


Shafts - Flexible - Panel Mount - Open
Shafts - Flexible - Panel Mount - Open

Also see combined categories:
All Flexible Panel Mount Shaft

See PDF file at bottom of internet page for Performance Data.

Related Information:

There is also a good range of Shafts - Flexible - Panel Mount - Open on the Small Parts and Bearings website.


Flexible Shaft


Shafts - Flexible - Coupling Ends - Open - Mild Steel
Shafts - Flexible - Coupling Ends - Open - Mild Steel

Also see combined categories:
All Coupling End Flexible Shaft

Flexible shafting with coupling ends ready to attach to a fixed shaft.

1.7 and 2.5mm cable diameters can be operated manually at 62mm bend radius with torsional break strength of 0.62 N.m. 3.3F shaft has a greater degree of flexibility than standard 3.3mm. 3.3F shaft can be used in dynamic mode if shaft isshortened to approximately 50mm.

Related Information:

There is also a good range of Shafts - Flexible - Coupling Ends - Open - Mild Steel on the Small Parts and Bearings website.


Splined Shafts and Bushes


Splined Shafts - Stainless Steel
Splined Shafts - Stainless Steel


Externally splined shafting. Bushes not included. Match with same size splined bushes.

Match bushes and shafts by Major Diameter. Steel on Steel is not meant for sliding applications. Steel on Bronze is OK for intermittent sliding under load.

There is also a good range of Splined Shafts - Stainless Steel on the Small Parts and Bearings website.


Shafting General Purpose


Rod - Drill Blanks
Rod - Drill Blanks

Also see combined categories:
All Silver Steel Drill Blanks
All Drill Rod

Made of hardened high speed steel.

Useful for turning and boring tools, constructing pins, hinge pins, arbors, pin gauges, dowels, preforating punchs. Can also be ground to make special cutting tools such as mills, spotfaces, angle or radii cutters, etc.

There is also a good range of Rod - Drill Blanks on the Small Parts and Bearings website.


Rod - Drill - General
Rod - Drill - General

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

Chrome vanadium alloy with unfinished ends. Requires heat treating to harden. Small diameters may not be perfectly straight. Heat treating by air, water or oil.

Related Information:

There is also a good range of Rod - Drill - General on the Small Parts and Bearings website.


Shafting Precision Ground


Rail Supports - Without Shaft
Rail Supports - Without Shaft

Also see combined categories:
All Shaft Supports

For mounting of linear shafting.

Shafting sold separately. Support is made from aluminium.

Related Information:

There is also a good range of Rail Supports - Without Shaft on the Small Parts and Bearings website.


Rail Supports - With Shaft
Rail Supports - With Shaft

Also see combined categories:
All Shaft Supports

Includes linear shafting.

Includes shaft to h6 tolerances. Support is made from aluminium.

Related Information:

There is also a good range of Rail Supports - With Shaft on the Small Parts and Bearings website.


Rail Supports - With Shaft - One Piece
Rail Supports - With Shaft - One Piece

Also see combined categories:
All Shaft Supports

One piece construction made from 6061-T6 Aluminium with ceramic coating to Mil-8625. Suitable for use with Frelon lined linear bearings.

Not suitable for linear ball bearings. Weld spatter, paints and other contaminants will not stick to the shaft. Vibration resistant and non-magnetic. Not suitable for harsh washdown environments.

Related Information:

There is also a good range of Rail Supports - With Shaft - One Piece on the Small Parts and Bearings website.


Supports - Pedestal Two Bolt
Supports - Pedestal Two Bolt

Also see combined categories:
All Supports

For linear shafting.

Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel.

Related Information:

There is also a good range of Supports - Pedestal Two Bolt on the Small Parts and Bearings website.


Rod - Drill - A-2 Air Hardening
Rod - Drill - A-2 Air Hardening

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

Air hardening. Maximum abrasion resistance. 65 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.

There is also a good range of Rod - Drill - A-2 Air Hardening on the Small Parts and Bearings website.


Rod - Drill - O-1 Oil Hardening
Rod - Drill - O-1 Oil Hardening

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

For general toolroom use. Good non-deforming characteristics. Moderate resistance to abrasion. 90 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.

There is also a good range of Rod - Drill - O-1 Oil Hardening on the Small Parts and Bearings website.


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 122538 products in 2633 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 122538 products in 2633 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.