Miniature Bearings Australia Pty Ltd

Searched For: HUBS CATEGORIES


Hubs


Hubs - Gear and Dial - Single
Hubs - Gear and Dial - Single

Also see combined categories:
All Hubs

Fairloctm Hubs require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Hubs - Gear and Dial - Single.

Related Information:

There is also a good range of Hubs - Gear and Dial - Single on the Small Parts and Bearings website.


Popular Bicycle Hub Parts
Popular Bicycle Hub Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

There is also a good range of Popular Bicycle Hub Parts on the Small Parts and Bearings website.


Ratchets - With Hub
Ratchets - With Hub


Match with pawls listed on this site.

This category may be available in the new MBA online store at Ratchets - With Hub.

Related Information:

There is also a good range of Ratchets - With Hub on the Small Parts and Bearings website.


Ratchets - Without Hub
Ratchets - Without Hub


Match with pawls listed on this site.

This category may be available in the new MBA online store at Ratchets - Without Hub.

Related Information:

There is also a good range of Ratchets - Without Hub on the Small Parts and Bearings website.


Couplings - Oldham - Hubs - Clamp Style
Couplings - Oldham - Hubs - Clamp Style

Also see combined categories:
All Insert and Jaw Type Couplings
All Oldham Hubs

0.06 to 44 Nm. Max Speed: 3000 RPM.

Single hubs. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.

Related Information:

There is also a good range of Couplings - Oldham - Hubs - Clamp Style on the Small Parts and Bearings website.


Couplings - Geargrip - Precision - Hubs Only
Couplings - Geargrip - Precision - Hubs Only


Match with sleeves from sleeves category

This category may be available in the new MBA online store at Couplings - Geargrip - Precision - Hubs Only.

Related Information:

There is also a good range of Couplings - Geargrip - Precision - Hubs Only on the Small Parts and Bearings website.


Couplings - Three Jaw Type - Hubs
Couplings - Three Jaw Type - Hubs


Match with Three Jaw Type inserts by OD. Two Hubs and one insert will be needed to make a complete coupling.

Complete with keyway and set screw. No lubrication needed. This category may be available in the new MBA online store at Couplings - Three Jaw Type - Hubs.

Related Information:

There is also a good range of Couplings - Three Jaw Type - Hubs on the Small Parts and Bearings website.


Couplings - Crowned Tooth Gear - Hubs Only
Couplings - Crowned Tooth Gear - Hubs Only


Match with sleeves from the sleeves category

+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.

Related Information:

There is also a good range of Couplings - Crowned Tooth Gear - Hubs Only on the Small Parts and Bearings website.


Check Size Before Ordering DT Swiss Hubs Parts
Check Size Before Ordering DT Swiss Hubs Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

There is also a good range of Check Size Before Ordering DT Swiss Hubs Parts on the Small Parts and Bearings website.


Couplings - Geargrip - Precision - Sleeves Only
Couplings - Geargrip - Precision - Sleeves Only


Match with hubs from hubs category

This category may be available in the new MBA online store at Couplings - Geargrip - Precision - Sleeves Only.

Related Information:

There is also a good range of Couplings - Geargrip - Precision - Sleeves Only on the Small Parts and Bearings website.


Pulleys - Timing - 5.000mm Pitch - HTD - 9mm Wide - Plastic - Fairloc Hub
Pulleys - Timing -  5.000mm Pitch - HTD - 9mm Wide - Plastic - Fairloc Hub

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit HTD 5.000mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide. Fairloc locking hub.


Related Information:

There is also a good range of Pulleys - Timing - 5.000mm Pitch - HTD - 9mm Wide - Plastic - Fairloc Hub on the Small Parts and Bearings website.


Pulleys - Timing - 2.032mm Pitch - MXL - 6.4mm Wide - Plastic - Metal Hub
Pulleys - Timing -  2.032mm Pitch - MXL - 6.4mm Wide - Plastic - Metal Hub

Also see combined categories:
All MXL 2.032mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide. Moulded single or double flange. With aluminium hub.

2.032mm metric is equivalent to 0.080 pitch imperial.

Related Information:

There is also a good range of Pulleys - Timing - 2.032mm Pitch - MXL - 6.4mm Wide - Plastic - Metal Hub on the Small Parts and Bearings website.


Couplings - Crowned Tooth Gear - Sleeve Only
Couplings - Crowned Tooth Gear - Sleeve Only


Match with hubs from the hubs category

+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.

Related Information:

There is also a good range of Couplings - Crowned Tooth Gear - Sleeve Only on the Small Parts and Bearings website.


Couplings - Three Jaw Type - Inserts
Couplings - Three Jaw Type - Inserts


Match with Three Jaw Type hubs by OD

Use Bost-Bronz inserts for high torque loads at slower speeds. Use rubber for quiter operation. Use polyurethane for moderate to heavy shock loads. This category may be available in the new MBA online store at Couplings - Three Jaw Type - Inserts.

Related Information:

There is also a good range of Couplings - Three Jaw Type - Inserts on the Small Parts and Bearings website.


Assemblies - Locking - Flanged
Assemblies - Locking - Flanged

Also see combined categories:
All Locking Assemblies

Suitable for locking sprockets, pulleys, eccentric shafts.

Locks components with a bore of (D) to shafts with a diameter of (d). C60 Steel (060A62). Outer ring expands whilst inner ring contracts. Flange eliminates axial movement of secured component. During tightening of the screws, the hub must be able to perform axial movement. Clearance h8 / H8. Surface roughness Rt max 10um shaft / hub.

There is also a good range of Assemblies - Locking - Flanged on the Small Parts and Bearings website.


Couplings - Spider Type C - Complete
Couplings - Spider Type C - Complete

Also see combined categories:
All Insert and Jaw Type Couplings

Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm. Match only hubs and spiders from listings SPIDER TYPE C. Inserts are held between the jaws of two hubs.

Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application. Polyurethane spider.

Related Information:

There is also a good range of Couplings - Spider Type C - Complete on the Small Parts and Bearings website.


Couplings - K Type
Couplings - K Type


Up to 3600 RPM - Minus 20 to Plus 60o C. 0.34 to 18 Nm.

Strong, flexible polyurethane or Hyrtel(R) is cut and tear resistant. Up to 3600 RPM. Urethane: Minus 20 to Plus 60o C / Hyrtel(R) : Minus 40 to Plus 100o C. Precision swaged mechanically crimped hubs. Annealed steel hubs.

Related Information:

There is also a good range of Couplings - K Type on the Small Parts and Bearings website.


Pulleys - Timing - 10.000mm Pitch - AT10 - 16mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 16mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:

There is also a good range of Pulleys - Timing - 10.000mm Pitch - AT10 - 16mm Wide - Through Bore on the Small Parts and Bearings website.


Pulleys - Timing - 10.000mm Pitch - AT10 - 25mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 25mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:

There is also a good range of Pulleys - Timing - 10.000mm Pitch - AT10 - 25mm Wide - Through Bore on the Small Parts and Bearings website.


Pulleys - Timing - 10.000mm Pitch - AT10 - 32mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 32mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:

There is also a good range of Pulleys - Timing - 10.000mm Pitch - AT10 - 32mm Wide - Through Bore on the Small Parts and Bearings website.


Pulleys - Timing - 10.000mm Pitch - AT10 - 50mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 50mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:

There is also a good range of Pulleys - Timing - 10.000mm Pitch - AT10 - 50mm Wide - Through Bore on the Small Parts and Bearings website.


Collars - Shaft - Hinged - Stainless Steel
Collars - Shaft - Hinged - Stainless Steel

Also see combined categories:
All Round Bore Shaft Collars
All Hinged Shaft Collars

Precision machined. Convenient easy-to-assemble design. 303 Stainless Steel

Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.

Related Information:

There is also a good range of Collars - Shaft - Hinged - Stainless Steel on the Small Parts and Bearings website.


Collars - Shaft - Hinged - Steel
Collars - Shaft - Hinged - Steel

Also see combined categories:
All Round Bore Shaft Collars
All Hinged Shaft Collars

Precision machined. Convenient easy-to-assemble design. Steel 12L14 (9SMn Pb36)

Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.

Related Information:

There is also a good range of Collars - Shaft - Hinged - Steel on the Small Parts and Bearings website.


Pulleys - Timing - 3.000mm Pitch - HTD - 9mm Wide - Plastic - Hubless
Pulleys - Timing -  3.000mm Pitch - HTD - 9mm Wide - Plastic - Hubless

Also see combined categories:
All 3mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit HTD 3.000mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide. Moulded single or double flange. No hub.

Suitable for use with shaftloc sleeves.

Related Information:

There is also a good range of Pulleys - Timing - 3.000mm Pitch - HTD - 9mm Wide - Plastic - Hubless on the Small Parts and Bearings website.


Gears - Spur - 24DP - 20 Degree - Plastic - Plain
Gears - Spur -  24DP - 20 Degree - Plastic - Plain

Also see combined categories:
All 24DP Spur Gears 20 Degree
All 24DP Spur Gears 20 Degree Plastic

PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Acetal or Nylon w/ Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 24DP - 20 Degree - Plastic - Plain.

There is also a good range of Gears - Spur - 24DP - 20 Degree - Plastic - Plain on the Small Parts and Bearings website.


Gears - Spur - 24DP - 20 Degree - Plastic with Insert
Gears - Spur -  24DP - 20 Degree - Plastic with Insert

Also see combined categories:
All 24DP Spur Gears 20 Degree
All 24DP Spur Gears 20 Degree Plastic

PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Acetal or Nylon w/ Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 24DP - 20 Degree - Plastic with Insert.

There is also a good range of Gears - Spur - 24DP - 20 Degree - Plastic with Insert on the Small Parts and Bearings website.


Couplings - Oldham - Disks for Clamp Style
Couplings - Oldham - Disks for Clamp Style

Also see combined categories:
All Insert and Jaw Type Couplings
All Oldham Disks

0.06 to 44 Nm. Max Speed: 3000 RPM.

Disk inserts. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.

Related Information:

There is also a good range of Couplings - Oldham - Disks for Clamp Style on the Small Parts and Bearings website.


Sprocket Plates - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore
Sprocket Plates - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm simplex chain (08B BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs.

Related Information:

There is also a good range of Sprocket Plates - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore on the Small Parts and Bearings website.


Sprocket Plates - 12.7 x 7.85mm - Simplex - Carbon Steel - Plain Bore
Sprocket Plates - 12.7 x 7.85mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.85mm simplex chain (40-1 ASA)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs.

Related Information:

There is also a good range of Sprocket Plates - 12.7 x 7.85mm - Simplex - Carbon Steel - Plain Bore on the Small Parts and Bearings website.


Gears - Spur - Module 0.4 - Brass
Gears - Spur - Module 0.4 - Brass

Also see combined categories:
All Module 0.4 Spur Gears
All Metal Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.4 - Brass.

There is also a good range of Gears - Spur - Module 0.4 - Brass on the Small Parts and Bearings website.


Gears - Spur - Module 0.4 - Plastic
Gears - Spur - Module 0.4 - Plastic

Also see combined categories:
All Module 0.4 Spur Gears
All Plastic Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.4 - Plastic.

There is also a good range of Gears - Spur - Module 0.4 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.5 - Plastic
Gears - Spur - Module 0.5 - Plastic

Also see combined categories:
All Module 0.5 Spur Gears
All Plastic Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.5 - Plastic.

There is also a good range of Gears - Spur - Module 0.5 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.7 - Plastic
Gears - Spur - Module 0.7 - Plastic


PCD = No. of Teeth x 0.700mm. 20o Pressure Angle. Acetal.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.7 - Plastic.

There is also a good range of Gears - Spur - Module 0.7 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.8 - Plastic
Gears - Spur - Module 0.8 - Plastic

Also see combined categories:
All Module 0.8 Spur Gears
All Plastic Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Plastic.

There is also a good range of Gears - Spur - Module 0.8 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 1 - Plastic
Gears - Spur - Module 1 - Plastic

Also see combined categories:
All Module 1.0 Spur Gears
All Plastic Module 1.0 Spur Gears

PCD = No. of Teeth x 1.000mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 1 - Plastic.

There is also a good range of Gears - Spur - Module 1 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 3 - Plastic
Gears - Spur - Module 3 - Plastic

Also see combined categories:
All Module 3.0 Spur Gears

PCD = No. of Teeth x 3.000mm. 20o Pressure Angle. Nylon

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 3 - Plastic.

There is also a good range of Gears - Spur - Module 3 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.8 - Aluminium
Gears - Spur - Module 0.8 - Aluminium

Also see combined categories:
All Module 0.8 Spur Gears
All Metal Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 2024 aluminium

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Aluminium.

There is also a good range of Gears - Spur - Module 0.8 - Aluminium on the Small Parts and Bearings website.


Gears - Spur - Module 1.25 - Stainless
Gears - Spur - Module 1.25 - Stainless

Also see combined categories:
All Module 1.25 Spur Gears
All Metal Module 1.25 Spur Gears

PCD = No. of Teeth x 1.250mm. 20o Pressure Angle. 303 stainless steel

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 1.25 - Stainless.

There is also a good range of Gears - Spur - Module 1.25 - Stainless on the Small Parts and Bearings website.


Gears - Spur - Module 1.5 - Plastic
Gears - Spur - Module 1.5 - Plastic

Also see combined categories:
All Module 1.5 Spur Gears
All Plastic Module 1.5 Spur Gears

PCD = No. of Teeth x 1.500mm. 20o Pressure Angle. Acetal and Nylon

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 1.5 - Plastic.

There is also a good range of Gears - Spur - Module 1.5 - Plastic on the Small Parts and Bearings website.


Elements - Locking
Elements - Locking

Also see combined categories:
All Locking Assemblies

2.4 to 2200 Nm, 6-80mm Bores

ETG 100 High Strength Steel for sizes up to 55mm bore. C60 Steel for sizes over 55mm bore. Recommended machining tolerances Shaft h8, Hub H8. This category may be available in the new MBA online store at Elements - Locking.

There is also a good range of Elements - Locking on the Small Parts and Bearings website.


Gears - Spur - Module 0.4 - Plastic with Insert
Gears - Spur - Module 0.4 - Plastic with Insert

Also see combined categories:
All Module 0.4 Spur Gears
All Plastic Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.4 - Plastic with Insert.

There is also a good range of Gears - Spur - Module 0.4 - Plastic with Insert on the Small Parts and Bearings website.


Gears - Spur - Module 0.5 - Plastic with Insert
Gears - Spur - Module 0.5 - Plastic with Insert

Also see combined categories:
All Module 0.5 Spur Gears
All Plastic Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.5 - Plastic with Insert.

There is also a good range of Gears - Spur - Module 0.5 - Plastic with Insert on the Small Parts and Bearings website.


Gears - Spur - Module 0.5 - Stainless
Gears - Spur - Module 0.5 - Stainless

Also see combined categories:
All Module 0.5 Spur Gears
All Metal Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.5 - Stainless.

There is also a good range of Gears - Spur - Module 0.5 - Stainless on the Small Parts and Bearings website.


Gears - Spur - Module 0.8 - Plastic with Insert
Gears - Spur - Module 0.8 - Plastic with Insert

Also see combined categories:
All Module 0.8 Spur Gears
All Plastic Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Plastic with Insert.

There is also a good range of Gears - Spur - Module 0.8 - Plastic with Insert on the Small Parts and Bearings website.


Gears - Spur - Module 0.8 - Stainless
Gears - Spur - Module 0.8 - Stainless

Also see combined categories:
All Module 0.8 Spur Gears
All Metal Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Stainless.

There is also a good range of Gears - Spur - Module 0.8 - Stainless on the Small Parts and Bearings website.


Pulleys - Timing - 5.000mm Pitch - AT5 - 10mm Wide - Through Bore
Pulleys - Timing -  5.000mm Pitch - AT5 - 10mm Wide - Through Bore

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT5 Series belts

Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size. This category may be available in the new MBA online store at Pulleys - Timing - 5.000mm Pitch - AT5 - 10mm Wide - Through Bore.

Related Information:

There is also a good range of Pulleys - Timing - 5.000mm Pitch - AT5 - 10mm Wide - Through Bore on the Small Parts and Bearings website.


Pulleys - Timing - 5.000mm Pitch - AT5 - 16mm Wide - Through Bore
Pulleys - Timing -  5.000mm Pitch - AT5 - 16mm Wide - Through Bore

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT5 Series belts

Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size. This category may be available in the new MBA online store at Pulleys - Timing - 5.000mm Pitch - AT5 - 16mm Wide - Through Bore.

Related Information:

There is also a good range of Pulleys - Timing - 5.000mm Pitch - AT5 - 16mm Wide - Through Bore on the Small Parts and Bearings website.


Pulleys - Timing - 5.000mm Pitch - AT5 - 25mm Wide - Through Bore
Pulleys - Timing -  5.000mm Pitch - AT5 - 25mm Wide - Through Bore

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT5 Series belts

Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size. This category may be available in the new MBA online store at Pulleys - Timing - 5.000mm Pitch - AT5 - 25mm Wide - Through Bore.

Related Information:

There is also a good range of Pulleys - Timing - 5.000mm Pitch - AT5 - 25mm Wide - Through Bore on the Small Parts and Bearings website.


Reducers - Bore
Reducers - Bore


Inch to Metric / Inch to Inch / Metric to Metric. Brass reducing bushes.

S = Recommended set screw positions. C = Recommended position for single set screw fastening. T = Recommended position for tangential screw in clamp hub. This category may be available in the new MBA online store at Reducers - Bore.

Related Information:

There is also a good range of Reducers - Bore on the Small Parts and Bearings website.


Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Through Bore
Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Through Bore

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.

Cast Iron and Steel. Hub requires drilling and tapping. Bore requires machining to finished size. This category may be available in the new MBA online store at Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Through Bore.

Related Information:

There is also a good range of Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Through Bore on the Small Parts and Bearings website.





Main Pages

5 Axis Machine Tool Bearings About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Distributor Locations Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Satellite Reaction Wheels Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 218356 products in 2137 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 218356 products in 2137 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.