Miniature Bearings Australia Pty Ltd

HUBS CATEGORIES


Hubs - Gear and Dial - Single
Hubs - Gear and Dial - Single

Also see combined categories:
All Hubs

Fairloctm Hubs require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.

Related Information:

There is also a good range of Hubs - Gear and Dial - Single on the Small Parts and Bearings website.


Ratchets - With Hub
Ratchets - With Hub


Match with pawls listed on this site.


Related Information:

There is also a good range of Ratchets - With Hub on the Small Parts and Bearings website.


Ratchets - Without Hub
Ratchets - Without Hub


Match with pawls listed on this site.


Related Information:

There is also a good range of Ratchets - Without Hub on the Small Parts and Bearings website.


Couplings - Oldham - Hubs - Clamp Style
Couplings - Oldham - Hubs - Clamp Style

Also see combined categories:
All Insert and Jaw Type Couplings
All Oldham Hubs

0.06 to 44 Nm. Max Speed: 3000 RPM.

Single hubs. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.

Related Information:

There is also a good range of Couplings - Oldham - Hubs - Clamp Style on the Small Parts and Bearings website.


Couplings - Geargrip - Precision - Hubs Only
Couplings - Geargrip - Precision - Hubs Only


Match with sleeves from sleeves category


Related Information:

There is also a good range of Couplings - Geargrip - Precision - Hubs Only on the Small Parts and Bearings website.


Couplings - Sleeve Type - Hubs
Couplings - Sleeve Type - Hubs


0.05 to 2.1 Nm. Max Speed 1750 rpm.

Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.

Related Information:

There is also a good range of Couplings - Sleeve Type - Hubs on the Small Parts and Bearings website.


Size List Popular Bicycle Hub Parts
Size List Popular Bicycle Hub Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

There is also a good range of Size List Popular Bicycle Hub Parts on the Small Parts and Bearings website.


Rollers - Urethane Feed - With Hub
Rollers - Urethane Feed - With Hub

Also see combined categories:
All Tyred OD Bearings
All Rollers

Urethane coated aluminium alloy feed rollers with hub.

Roller - Urethane 60 Durometer, Ground Outside Diameter. Sleeve - Aluminium.

Related Information:

There is also a good range of Rollers - Urethane Feed - With Hub on the Small Parts and Bearings website.


Couplings - Spider Type B - Hubs Only
Couplings - Spider Type B - Hubs Only


Match 2 hubs with a spider from the spiders category. Match only rubber spiders from listings SPIDER TYPE B. Insert is set between the jaws of two hubs.

Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM. Metal hubs to suit rubber spiders type B.

Related Information:

There is also a good range of Couplings - Spider Type B - Hubs Only on the Small Parts and Bearings website.


Couplings - Spline Type - Spare Hubs
Couplings - Spline Type - Spare Hubs

Also see combined categories:
All Insert and Jaw Type Couplings

0.5 to 4.5 Nm. 12000 to 24000 rpm.

Maximum parallel offset 0.2mm, Maximum working angle 2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 oC.

Related Information:

There is also a good range of Couplings - Spline Type - Spare Hubs on the Small Parts and Bearings website.


Couplings - Three Jaw Type - Hubs
Couplings - Three Jaw Type - Hubs


Match with Three Jaw Type inserts by OD. Two Hubs and one insert will be needed to make a complete coupling.

Complete with keyway and set screw. No lubrication needed.

Related Information:

There is also a good range of Couplings - Three Jaw Type - Hubs on the Small Parts and Bearings website.


Couplings - Crowned Tooth Gear - Hubs Only
Couplings - Crowned Tooth Gear - Hubs Only


Match with sleeves from the sleeves category

+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.

Related Information:

There is also a good range of Couplings - Crowned Tooth Gear - Hubs Only on the Small Parts and Bearings website.


Check Size Before Ordering DT Swiss Hubs Parts
Check Size Before Ordering DT Swiss Hubs Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

There is also a good range of Check Size Before Ordering DT Swiss Hubs Parts on the Small Parts and Bearings website.


Couplings - Geargrip - Precision - Sleeves Only
Couplings - Geargrip - Precision - Sleeves Only


Match with hubs from hubs category


Related Information:

There is also a good range of Couplings - Geargrip - Precision - Sleeves Only on the Small Parts and Bearings website.


Pulleys - Timing - 5.000mm Pitch - HTD - 9mm Wide - Plastic - Fairloc Hub
Pulleys - Timing -  5.000mm Pitch - HTD - 9mm Wide - Plastic - Fairloc Hub

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit HTD 5.000mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide. Fairloc locking hub.


Related Information:

There is also a good range of Pulleys - Timing - 5.000mm Pitch - HTD - 9mm Wide - Plastic - Fairloc Hub on the Small Parts and Bearings website.


Pulleys - Timing - 2.032mm Pitch - MXL - 6.4mm Wide - Plastic - Metal Hub
Pulleys - Timing -  2.032mm Pitch - MXL - 6.4mm Wide - Plastic - Metal Hub

Also see combined categories:
All MXL 2.032mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide. Moulded single or double flange. With aluminium hub.

2.032mm metric is equivalent to 0.080 pitch imperial.

Related Information:

There is also a good range of Pulleys - Timing - 2.032mm Pitch - MXL - 6.4mm Wide - Plastic - Metal Hub on the Small Parts and Bearings website.


Couplings - Crowned Tooth Gear - Sleeve Only
Couplings - Crowned Tooth Gear - Sleeve Only


Match with hubs from the hubs category

+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.

Related Information:

There is also a good range of Couplings - Crowned Tooth Gear - Sleeve Only on the Small Parts and Bearings website.


Couplings - Double Disk - Aluminium
Couplings - Double Disk - Aluminium


Zero Backlash - High Torsional Stiffness.

Hub and Spacer: Aluminium Alloy. Pin and Disc: Stainless Steel. Max Axial Play: +/-0.5mm. 0.7 to 12.5 Nm. 3000 to 19000 rpm.

Related Information:

There is also a good range of Couplings - Double Disk - Aluminium on the Small Parts and Bearings website.


Couplings - Three Jaw Type - Inserts
Couplings - Three Jaw Type - Inserts


Match with Three Jaw Type hubs by OD

Use Bost-Bronz inserts for high torque loads at slower speeds. Use rubber for quiter operation. Use polyurethane for moderate to heavy shock loads.

Related Information:

There is also a good range of Couplings - Three Jaw Type - Inserts on the Small Parts and Bearings website.


Couplings - Sleeve Type - Sleeves
Couplings - Sleeve Type - Sleeves


0.05 to 2.1 Nm. Max Speed 1750 rpm.

Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.

Related Information:

There is also a good range of Couplings - Sleeve Type - Sleeves on the Small Parts and Bearings website.


Couplings - Spider Type B - Complete
Couplings - Spider Type B - Complete

Also see combined categories:
All Insert and Jaw Type Couplings

Max 3600 RPM. 0.39 to 16.27 Nm. Match only hubs and spiders from listings SPIDER TYPE B. Insert is set between the jaws of two hubs.

Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM. Rubber spider and metal hubs.

Related Information:

There is also a good range of Couplings - Spider Type B - Complete on the Small Parts and Bearings website.


Couplings - Spider Type C - Complete
Couplings - Spider Type C - Complete

Also see combined categories:
All Insert and Jaw Type Couplings

Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm. Match only hubs and spiders from listings SPIDER TYPE C. Inserts are held between the jaws of two hubs.

Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application. Polyurethane spider.

Related Information:

There is also a good range of Couplings - Spider Type C - Complete on the Small Parts and Bearings website.


Couplings - K Type
Couplings - K Type


Up to 3600 RPM - Minus 20 to Plus 60o C. 0.34 to 18 Nm.

Strong, flexible polyurethane or Hyrtel(R) is cut and tear resistant. Up to 3600 RPM. Urethane: Minus 20 to Plus 60o C / Hyrtel(R) : Minus 40 to Plus 100o C. Precision swaged mechanically crimped hubs. Annealed steel hubs.

Related Information:

There is also a good range of Couplings - K Type on the Small Parts and Bearings website.


Gears - Spur - Module 0.15 - Brass
Gears - Spur - Module 0.15 - Brass


PCD = No. of Teeth x 0.150mm. 20o Pressure Angle.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.

There is also a good range of Gears - Spur - Module 0.15 - Brass on the Small Parts and Bearings website.


Gears - Spur - Module 0.4 - Brass
Gears - Spur - Module 0.4 - Brass

Also see combined categories:
All Module 0.4 Spur Gears
All Metal Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.

There is also a good range of Gears - Spur - Module 0.4 - Brass on the Small Parts and Bearings website.


Pulleys - Timing - 5.000mm Pitch - AT5 - 10mm Wide - Through Bore
Pulleys - Timing -  5.000mm Pitch - AT5 - 10mm Wide - Through Bore

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT5 Series belts

Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size.

Related Information:

There is also a good range of Pulleys - Timing - 5.000mm Pitch - AT5 - 10mm Wide - Through Bore on the Small Parts and Bearings website.


Pulleys - Timing - 5.000mm Pitch - AT5 - 16mm Wide - Through Bore
Pulleys - Timing -  5.000mm Pitch - AT5 - 16mm Wide - Through Bore

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT5 Series belts

Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size.

Related Information:

There is also a good range of Pulleys - Timing - 5.000mm Pitch - AT5 - 16mm Wide - Through Bore on the Small Parts and Bearings website.


Pulleys - Timing - 5.000mm Pitch - AT5 - 25mm Wide - Through Bore
Pulleys - Timing -  5.000mm Pitch - AT5 - 25mm Wide - Through Bore

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT5 Series belts

Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size.

Related Information:

There is also a good range of Pulleys - Timing - 5.000mm Pitch - AT5 - 25mm Wide - Through Bore on the Small Parts and Bearings website.


Gears - Spur - Module 0.4 - Plastic
Gears - Spur - Module 0.4 - Plastic

Also see combined categories:
All Module 0.4 Spur Gears
All Plastic Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.

There is also a good range of Gears - Spur - Module 0.4 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.5 - Plastic
Gears - Spur - Module 0.5 - Plastic

Also see combined categories:
All Module 0.5 Spur Gears
All Plastic Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.

There is also a good range of Gears - Spur - Module 0.5 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.75 - Brass
Gears - Spur - Module 0.75 - Brass


PCD = No. of Teeth x 0.750mm. 20o Pressure Angle. Brass.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.

There is also a good range of Gears - Spur - Module 0.75 - Brass on the Small Parts and Bearings website.


Gears - Spur - Module 0.7 - Plastic
Gears - Spur - Module 0.7 - Plastic


PCD = No. of Teeth x 0.700mm. 20o Pressure Angle. Acetal.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.

There is also a good range of Gears - Spur - Module 0.7 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.8 - Plastic
Gears - Spur - Module 0.8 - Plastic

Also see combined categories:
All Module 0.8 Spur Gears
All Plastic Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.

There is also a good range of Gears - Spur - Module 0.8 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 1.25 - Plastic
Gears - Spur - Module 1.25 - Plastic

Also see combined categories:
All Module 1.25 Spur Gears

PCD = No. of Teeth x 1.250mm. 20o Pressure Angle. Acetal.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.

There is also a good range of Gears - Spur - Module 1.25 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 1 - Plastic
Gears - Spur - Module 1 - Plastic

Also see combined categories:
All Module 1.0 Spur Gears
All Plastic Module 1.0 Spur Gears

PCD = No. of Teeth x 1.000mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.

There is also a good range of Gears - Spur - Module 1 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 3 - Plastic
Gears - Spur - Module 3 - Plastic

Also see combined categories:
All Module 3.0 Spur Gears

PCD = No. of Teeth x 3.000mm. 20o Pressure Angle. Nylon

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.

There is also a good range of Gears - Spur - Module 3 - Plastic on the Small Parts and Bearings website.


Couplings - Bellows - Set Screw - 316 Stainless
Couplings - Bellows - Set Screw - 316 Stainless

Also see combined categories:
All Bellows Couplings

Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics

Stainless Steel 303L Bellows. Stainless Steel 316 Hubs.

Related Information:

There is also a good range of Couplings - Bellows - Set Screw - 316 Stainless on the Small Parts and Bearings website.


Gears - Spur - Module 0.5 - Aluminium
Gears - Spur - Module 0.5 - Aluminium

Also see combined categories:
All Module 0.5 Spur Gears
All Metal Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. 2024 aluminium

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.

There is also a good range of Gears - Spur - Module 0.5 - Aluminium on the Small Parts and Bearings website.


Gears - Spur - Module 0.8 - Aluminium
Gears - Spur - Module 0.8 - Aluminium

Also see combined categories:
All Module 0.8 Spur Gears
All Metal Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 2024 aluminium

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.

There is also a good range of Gears - Spur - Module 0.8 - Aluminium on the Small Parts and Bearings website.


Gears - Spur - Module 2.5 - Steel
Gears - Spur - Module 2.5 - Steel

Also see combined categories:
All Module 2.5 Spur Gears
All Metal Module 2.5 Spur Gears

PCD = No. of Teeth x 2.500mm. 20o Pressure Angle. Carbon steel

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.

There is also a good range of Gears - Spur - Module 2.5 - Steel on the Small Parts and Bearings website.


Pulleys - Timing - 10.000mm Pitch - AT10 - 16mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 16mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:

There is also a good range of Pulleys - Timing - 10.000mm Pitch - AT10 - 16mm Wide - Through Bore on the Small Parts and Bearings website.


Pulleys - Timing - 10.000mm Pitch - AT10 - 25mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 25mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:

There is also a good range of Pulleys - Timing - 10.000mm Pitch - AT10 - 25mm Wide - Through Bore on the Small Parts and Bearings website.


Pulleys - Timing - 10.000mm Pitch - AT10 - 32mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 32mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:

There is also a good range of Pulleys - Timing - 10.000mm Pitch - AT10 - 32mm Wide - Through Bore on the Small Parts and Bearings website.


Pulleys - Timing - 10.000mm Pitch - AT10 - 50mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 50mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:

There is also a good range of Pulleys - Timing - 10.000mm Pitch - AT10 - 50mm Wide - Through Bore on the Small Parts and Bearings website.


Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Through Bore
Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Through Bore

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.

Cast Iron and Steel. Hub requires drilling and tapping. Bore requires machining to finished size.

Related Information:

There is also a good range of Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Through Bore on the Small Parts and Bearings website.


Gears - Spur - Module 0.4 - Plastic with Insert
Gears - Spur - Module 0.4 - Plastic with Insert

Also see combined categories:
All Module 0.4 Spur Gears
All Plastic Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.

There is also a good range of Gears - Spur - Module 0.4 - Plastic with Insert on the Small Parts and Bearings website.


Gears - Spur - Module 0.5 - Plastic with Insert
Gears - Spur - Module 0.5 - Plastic with Insert

Also see combined categories:
All Module 0.5 Spur Gears
All Plastic Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.

There is also a good range of Gears - Spur - Module 0.5 - Plastic with Insert on the Small Parts and Bearings website.


Gears - Spur - Module 0.8 - Plastic with Insert
Gears - Spur - Module 0.8 - Plastic with Insert

Also see combined categories:
All Module 0.8 Spur Gears
All Plastic Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.

There is also a good range of Gears - Spur - Module 0.8 - Plastic with Insert on the Small Parts and Bearings website.


Gears - Spur - Module 1.25 - Stainless
Gears - Spur - Module 1.25 - Stainless

Also see combined categories:
All Module 1.25 Spur Gears
All Metal Module 1.25 Spur Gears

PCD = No. of Teeth x 1.250mm. 20o Pressure Angle. 303 stainless steel

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.

There is also a good range of Gears - Spur - Module 1.25 - Stainless on the Small Parts and Bearings website.


Gears - Spur - Module 1.5 - Plastic
Gears - Spur - Module 1.5 - Plastic

Also see combined categories:
All Module 1.5 Spur Gears
All Plastic Module 1.5 Spur Gears

PCD = No. of Teeth x 1.500mm. 20o Pressure Angle. Acetal and Nylon

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.

There is also a good range of Gears - Spur - Module 1.5 - Plastic on the Small Parts and Bearings website.


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 126925 products in 2252 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 126925 products in 2252 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.