HUBS CATEGORIES
Hubs - Gear and Dial - Single
Fairloctm Hubs require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
Related Information:
There is also a good range of Hubs - Gear and Dial - Single on the Small Parts and Bearings website.
Ratchets - With Hub
Match with pawls listed on this site.
Related Information:
There is also a good range of Ratchets - With Hub on the Small Parts and Bearings website.
Ratchets - Without Hub
Match with pawls listed on this site.
Related Information:
There is also a good range of Ratchets - Without Hub on the Small Parts and Bearings website.
Couplings - Oldham - Hubs - Clamp Style
0.06 to 44 Nm. Max Speed: 3000 RPM.
Single hubs. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.
Related Information:
There is also a good range of Couplings - Oldham - Hubs - Clamp Style on the Small Parts and Bearings website.
Couplings - Geargrip - Precision - Hubs Only
Match with sleeves from sleeves category
Related Information:
There is also a good range of Couplings - Geargrip - Precision - Hubs Only on the Small Parts and Bearings website.
Couplings - Sleeve Type - Hubs
0.05 to 2.1 Nm. Max Speed 1750 rpm.
Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.
Related Information:
There is also a good range of Couplings - Sleeve Type - Hubs on the Small Parts and Bearings website.
Size List Popular Bicycle Hub Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
There is also a good range of Size List Popular Bicycle Hub Parts on the Small Parts and Bearings website.
Couplings - Spider Type B - Hubs Only
Match 2 hubs with a spider from the spiders category. Match only rubber spiders from listings SPIDER TYPE B. Insert is set between the jaws of two hubs.
Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM. Metal hubs to suit rubber spiders type B.
Related Information:
There is also a good range of Couplings - Spider Type B - Hubs Only on the Small Parts and Bearings website.
Couplings - Spline Type - Spare Hubs
0.5 to 4.5 Nm. 12000 to 24000 rpm.
Maximum parallel offset 0.2mm, Maximum working angle 2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 oC.
Related Information:
There is also a good range of Couplings - Spline Type - Spare Hubs on the Small Parts and Bearings website.
Couplings - Three Jaw Type - Hubs
Match with Three Jaw Type inserts by OD. Two Hubs and one insert will be needed to make a complete coupling.
Complete with keyway and set screw. No lubrication needed.
Related Information:
There is also a good range of Couplings - Three Jaw Type - Hubs on the Small Parts and Bearings website.
Couplings - Crowned Tooth Gear - Hubs Only
Match with sleeves from the sleeves category
+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.
Related Information:
There is also a good range of Couplings - Crowned Tooth Gear - Hubs Only on the Small Parts and Bearings website.
Check Size Before Ordering DT Swiss Hubs Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
There is also a good range of Check Size Before Ordering DT Swiss Hubs Parts on the Small Parts and Bearings website.
Couplings - Geargrip - Precision - Sleeves Only
Match with hubs from hubs category
Related Information:
There is also a good range of Couplings - Geargrip - Precision - Sleeves Only on the Small Parts and Bearings website.
Pulleys - Timing - 5.000mm Pitch - HTD - 9mm Wide - Plastic - Fairloc Hub
Timing Pulleys to suit HTD 5.000mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide. Fairloc locking hub.
Related Information:
There is also a good range of Pulleys - Timing - 5.000mm Pitch - HTD - 9mm Wide - Plastic - Fairloc Hub on the Small Parts and Bearings website.
Pulleys - Timing - 2.032mm Pitch - MXL - 6.4mm Wide - Plastic - Metal Hub
Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide. Moulded single or double flange. With aluminium hub.
2.032mm metric is equivalent to 0.080 pitch imperial.
Related Information:
There is also a good range of Pulleys - Timing - 2.032mm Pitch - MXL - 6.4mm Wide - Plastic - Metal Hub on the Small Parts and Bearings website.
Couplings - Crowned Tooth Gear - Sleeve Only
Match with hubs from the hubs category
+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.
Related Information:
There is also a good range of Couplings - Crowned Tooth Gear - Sleeve Only on the Small Parts and Bearings website.
Couplings - Double Disk - Aluminium
Zero Backlash - High Torsional Stiffness.
Hub and Spacer: Aluminium Alloy. Pin and Disc: Stainless Steel. Max Axial Play: +/-0.5mm. 0.7 to 12.5 Nm. 3000 to 19000 rpm.
Related Information:
There is also a good range of Couplings - Double Disk - Aluminium on the Small Parts and Bearings website.
Couplings - Three Jaw Type - Inserts
Match with Three Jaw Type hubs by OD
Use Bost-Bronz inserts for high torque loads at slower speeds. Use rubber for quiter operation. Use polyurethane for moderate to heavy shock loads.
Related Information:
There is also a good range of Couplings - Three Jaw Type - Inserts on the Small Parts and Bearings website.
Couplings - Sleeve Type - Sleeves
0.05 to 2.1 Nm. Max Speed 1750 rpm.
Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.
Related Information:
There is also a good range of Couplings - Sleeve Type - Sleeves on the Small Parts and Bearings website.
Couplings - Spider Type C - Complete
Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm. Match only hubs and spiders from listings SPIDER TYPE C. Inserts are held between the jaws of two hubs.
Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application. Polyurethane spider.
Related Information:
There is also a good range of Couplings - Spider Type C - Complete on the Small Parts and Bearings website.
Gears - Spur - Module 0.15 - Brass
PCD = No. of Teeth x 0.150mm. 20o Pressure Angle.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 0.15 - Brass on the Small Parts and Bearings website.
Gears - Spur - Module 0.4 - Brass
PCD = No. of Teeth x 0.400mm. 20o Pressure Angle.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 0.4 - Brass on the Small Parts and Bearings website.
Pulleys - Timing - 5.000mm Pitch - AT5 - 10mm Wide - Through Bore
Timing pulleys to suit AT5 Series belts
Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size.
Related Information:
There is also a good range of Pulleys - Timing - 5.000mm Pitch - AT5 - 10mm Wide - Through Bore on the Small Parts and Bearings website.
Pulleys - Timing - 5.000mm Pitch - AT5 - 16mm Wide - Through Bore
Timing pulleys to suit AT5 Series belts
Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size.
Related Information:
There is also a good range of Pulleys - Timing - 5.000mm Pitch - AT5 - 16mm Wide - Through Bore on the Small Parts and Bearings website.
Pulleys - Timing - 5.000mm Pitch - AT5 - 25mm Wide - Through Bore
Timing pulleys to suit AT5 Series belts
Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size.
Related Information:
There is also a good range of Pulleys - Timing - 5.000mm Pitch - AT5 - 25mm Wide - Through Bore on the Small Parts and Bearings website.
Gears - Spur - Module 0.4 - Plastic
PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 0.4 - Plastic on the Small Parts and Bearings website.
Gears - Spur - Module 0.5 - Plastic
PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 0.5 - Plastic on the Small Parts and Bearings website.
Gears - Spur - Module 0.7 - Plastic
PCD = No. of Teeth x 0.700mm. 20o Pressure Angle. Acetal.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 0.7 - Plastic on the Small Parts and Bearings website.
Gears - Spur - Module 0.8 - Plastic
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 0.8 - Plastic on the Small Parts and Bearings website.
Gears - Spur - Module 1 - Plastic
PCD = No. of Teeth x 1.000mm. 20o Pressure Angle. Acetal
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 1 - Plastic on the Small Parts and Bearings website.
Gears - Spur - Module 3 - Plastic
PCD = No. of Teeth x 3.000mm. 20o Pressure Angle. Nylon
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 3 - Plastic on the Small Parts and Bearings website.
Couplings - Bellows - Set Screw - 316 Stainless
Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics
Stainless Steel 303L Bellows. Stainless Steel 316 Hubs.
Related Information:
There is also a good range of Couplings - Bellows - Set Screw - 316 Stainless on the Small Parts and Bearings website.
Gears - Spur - Module 0.8 - Aluminium
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 2024 aluminium
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 0.8 - Aluminium on the Small Parts and Bearings website.
Gears - Spur - Module 2.5 - Steel
PCD = No. of Teeth x 2.500mm. 20o Pressure Angle. Carbon steel
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 2.5 - Steel on the Small Parts and Bearings website.
Pulleys - Timing - 10.000mm Pitch - AT10 - 16mm Wide - Through Bore
Timing pulleys to suit AT10 Series belts
Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.
Related Information:
There is also a good range of Pulleys - Timing - 10.000mm Pitch - AT10 - 16mm Wide - Through Bore on the Small Parts and Bearings website.
Pulleys - Timing - 10.000mm Pitch - AT10 - 25mm Wide - Through Bore
Timing pulleys to suit AT10 Series belts
Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.
Related Information:
There is also a good range of Pulleys - Timing - 10.000mm Pitch - AT10 - 25mm Wide - Through Bore on the Small Parts and Bearings website.
Pulleys - Timing - 10.000mm Pitch - AT10 - 32mm Wide - Through Bore
Timing pulleys to suit AT10 Series belts
Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.
Related Information:
There is also a good range of Pulleys - Timing - 10.000mm Pitch - AT10 - 32mm Wide - Through Bore on the Small Parts and Bearings website.
Pulleys - Timing - 10.000mm Pitch - AT10 - 50mm Wide - Through Bore
Timing pulleys to suit AT10 Series belts
Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.
Related Information:
There is also a good range of Pulleys - Timing - 10.000mm Pitch - AT10 - 50mm Wide - Through Bore on the Small Parts and Bearings website.
Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Through Bore
Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.
Cast Iron and Steel. Hub requires drilling and tapping. Bore requires machining to finished size.
Related Information:
There is also a good range of Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Through Bore on the Small Parts and Bearings website.
Gears - Spur - Module 0.4 - Plastic with Insert
PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 0.4 - Plastic with Insert on the Small Parts and Bearings website.
Gears - Spur - Module 0.5 - Plastic with Insert
PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 0.5 - Plastic with Insert on the Small Parts and Bearings website.
Gears - Spur - Module 0.8 - Plastic with Insert
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 0.8 - Plastic with Insert on the Small Parts and Bearings website.
Gears - Spur - Module 1.25 - Stainless
PCD = No. of Teeth x 1.250mm. 20o Pressure Angle. 303 stainless steel
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 1.25 - Stainless on the Small Parts and Bearings website.
Gears - Spur - Module 1.5 - Plastic
PCD = No. of Teeth x 1.500mm. 20o Pressure Angle. Acetal and Nylon
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 1.5 - Plastic on the Small Parts and Bearings website.
Gears - Spur - Module 2 - Steel
PCD = No. of Teeth x 2.000mm. 20o Pressure Angle. AISI4135 carbon steel
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
There is also a good range of Gears - Spur - Module 2 - Steel on the Small Parts and Bearings website.
Collars - Shaft - Hinged - Stainless Steel
Precision machined. Convenient easy-to-assemble design. 303 Stainless Steel
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Related Information:
There is also a good range of Collars - Shaft - Hinged - Stainless Steel on the Small Parts and Bearings website.
Collars - Shaft - Hinged - Steel
Precision machined. Convenient easy-to-assemble design. Steel 12L14 (9SMn Pb36)
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Related Information:
There is also a good range of Collars - Shaft - Hinged - Steel on the Small Parts and Bearings website.
Pulleys - Timing - 12.700mm Pitch - H - 38.1mm Wide - Through Bore
Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.
Steel and Cast Iron. No grub screw. Hub requires drilling and tapping. Bore requires machining to finished size.
Related Information:
There is also a good range of Pulleys - Timing - 12.700mm Pitch - H - 38.1mm Wide - Through Bore on the Small Parts and Bearings website.
Pulleys - Timing - 12.700mm Pitch - H - 50.8mm Wide - Through Bore
Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.
Steel and Cast Iron. No grub screw. Hub requires drilling and tapping. Bore requires machining to finished size.
Related Information:
There is also a good range of Pulleys - Timing - 12.700mm Pitch - H - 50.8mm Wide - Through Bore on the Small Parts and Bearings website.
Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Through Bore
Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.
Steel and Cast Iron. No grub screw. Hub requires drilling and tapping. Bore requires machining to finished size.
Related Information:
There is also a good range of Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Through Bore on the Small Parts and Bearings website.
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Contact Us
Charity
Dental Bearings
Distributor Locations
Dowel Pins
Downloadable PDF Catalogue Ball Lock Pins
Downloadable PDF Catalogue Balls
Downloadable PDF Catalogue Ceramic Bearings
Downloadable PDF Catalogue Circlips
Downloadable PDF Catalogue Corrosion Resistant Bearings
Downloadable PDF Catalogue Disc Springs
Downloadable PDF Catalogue Dowel Pins
Downloadable PDF Catalogue Economy Bearings
Downloadable PDF Catalogue Hammer Drive Pins
Downloadable PDF Catalogue High Speed Bearings
Downloadable PDF Catalogue Key Steel
Downloadable PDF Catalogue Knobs
Downloadable PDF Catalogue Leveling Mounts
Downloadable PDF Catalogue Metallic Bushes
Downloadable PDF Catalogue O-Rings
Downloadable PDF Catalogue Pins
Downloadable PDF Catalogue Plastic Bearings
Downloadable PDF Catalogue Polyvee Belts and Pulleys
Downloadable PDF Catalogue Precision Shim Washers
Downloadable PDF Catalogue Push On and Push In Rings
Downloadable PDF Catalogue Rod & Tube
Downloadable PDF Catalogue Roll Pins
Downloadable PDF Catalogue Shaft Collars
Downloadable PDF Catalogue Shim Sheet
Downloadable PDF Catalogue Shoulder Screws
Downloadable PDF Catalogue Sintered Bronze Bushes
Downloadable PDF Catalogue Socket Set Screws
Downloadable PDF Catalogue Solid Bronze Bushes
Downloadable PDF Catalogue Spring Steel Strip
Downloadable PDF Catalogue Springs
Downloadable PDF Catalogue Standard Ball Bearing Range
Downloadable PDF Catalogue Super Precision Bearings
Downloadable PDF Catalogue Taper Pins
Downloadable PDF Catalogue Thrust Bearings
Downloadable PDF Catalogue Thumb Screws and Nuts
Downloadable PDF Catalogue Timing Belts
Downloadable PDF Catalogue Timing Pulley Stock
Downloadable PDF Catalogue Timing Pulleys
Downloadable PDF Catalogue Vibration Mounts
Downloadable PDF Catalogue Washers
Downloadable PDF Catalogue Wave Washers
Downloadable PDF Cross Reference ADR and SKF
Downloadable PDF Cross Reference Anderton Circlips
Downloadable PDF Cross Reference Barden Bearings
Downloadable PDF Cross Reference Essentra
Downloadable PDF Cross Reference Flocast
Downloadable PDF Cross Reference K&S Metals
Downloadable PDF Cross Reference McMaster Carr
Downloadable PDF Cross Reference Miniature Precison Bearings
Downloadable PDF Cross Reference Nordex
Downloadable PDF Cross Reference NSK and NTN
Downloadable PDF Cross Reference Ondrives
Downloadable PDF Cross Reference Reid Supply
Downloadable PDF Cross Reference SDP-SI Designatronics
Downloadable PDF Cross Reference Seeger Circlips
Downloadable PDF Cross Reference Sintered Bronze
Downloadable PDF Cross Reference Small Parts Inc
Downloadable PDF Cross Reference Timing Belts and Pulleys
Freight Rates and Shipping Times
Frequently Asked Questions
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Satellite Reaction Wheels
Shipping Rates and Times
Technical
Terms
5 Axis Machine Tool Bearings
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)
Miniature Bearings Australia offers 128084 products in 2100 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.
