Miniature Bearings Australia Pty Ltd

Gears metric helical categories


Pins Dowel


Pins - Hammer Drive - Flat Head
Pins - Hammer Drive - Flat Head

Also see combined categories:
All Hammer Drive Pins

Used to replace screws where the need to remove the pin is unlikely.

Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.

Related Information:

There is also a good range of Pins - Hammer Drive - Flat Head on the Small Parts and Bearings website.


Pins - Hammer Drive - Round Head - Stainless Steel
Pins - Hammer Drive - Round Head - Stainless Steel

Also see combined categories:
All Hammer Drive Pins

Used to replace screws where the need to remove the pin is unlikely.

Stainless Steel 304 Grade. Simple, low cost assembly. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.

Related Information:

There is also a good range of Pins - Hammer Drive - Round Head - Stainless Steel on the Small Parts and Bearings website.


Gears Metric Bevel


Gears - Bevel - Module 1.5 - Plastic
Gears - Bevel - Module 1.5 - Plastic

Also see combined categories:
All Metric Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. This category may be available in the new MBA online store at Gears - Bevel - Module 1.5 - Plastic.

Related Information:

There is also a good range of Gears - Bevel - Module 1.5 - Plastic on the Small Parts and Bearings website.


Gears - Bevel - Module 1 - Plastic
Gears - Bevel - Module 1 - Plastic

Also see combined categories:
All Metric Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. This category may be available in the new MBA online store at Gears - Bevel - Module 1 - Plastic.

Related Information:

There is also a good range of Gears - Bevel - Module 1 - Plastic on the Small Parts and Bearings website.


Gears Metric Mitre


Gears - Mitre - Module 0.5 - Plastic
Gears - Mitre - Module 0.5 - Plastic

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Acetal

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 0.5 - Plastic.

Related Information:

There is also a good range of Gears - Mitre - Module 0.5 - Plastic on the Small Parts and Bearings website.


Gears - Mitre - Module 1.5 - Brass
Gears - Mitre - Module 1.5 - Brass

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 1.5 - Brass.

Related Information:

There is also a good range of Gears - Mitre - Module 1.5 - Brass on the Small Parts and Bearings website.


Gears - Mitre - Module 1 - Brass
Gears - Mitre - Module 1 - Brass

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 1 - Brass.

Related Information:

There is also a good range of Gears - Mitre - Module 1 - Brass on the Small Parts and Bearings website.


Gears - Mitre - Module 1 - Plastic
Gears - Mitre - Module 1 - Plastic

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Acetal.

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 1 - Plastic.

Related Information:

There is also a good range of Gears - Mitre - Module 1 - Plastic on the Small Parts and Bearings website.


Gears - Mitre - Module 3 - Plastic
Gears - Mitre - Module 3 - Plastic

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Acetal

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 3 - Plastic.

Related Information:

There is also a good range of Gears - Mitre - Module 3 - Plastic on the Small Parts and Bearings website.


Gears Metric Spur


Gears - Spur - Module 0.4 - Brass
Gears - Spur - Module 0.4 - Brass

Also see combined categories:
All Module 0.4 Spur Gears
All Metal Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.4 - Brass.

There is also a good range of Gears - Spur - Module 0.4 - Brass on the Small Parts and Bearings website.


Gears - Spur - Module 0.4 - Plastic
Gears - Spur - Module 0.4 - Plastic

Also see combined categories:
All Module 0.4 Spur Gears
All Plastic Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.4 - Plastic.

There is also a good range of Gears - Spur - Module 0.4 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.5 - Plastic
Gears - Spur - Module 0.5 - Plastic

Also see combined categories:
All Module 0.5 Spur Gears
All Plastic Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.5 - Plastic.

There is also a good range of Gears - Spur - Module 0.5 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.5 - Stainless
Gears - Spur - Module 0.5 - Stainless

Also see combined categories:
All Module 0.5 Spur Gears
All Metal Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.5 - Stainless.

There is also a good range of Gears - Spur - Module 0.5 - Stainless on the Small Parts and Bearings website.


Gears - Spur - Module 0.7 - Plastic
Gears - Spur - Module 0.7 - Plastic


PCD = No. of Teeth x 0.700mm. 20o Pressure Angle. Acetal.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.7 - Plastic.

There is also a good range of Gears - Spur - Module 0.7 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.8 - Aluminium
Gears - Spur - Module 0.8 - Aluminium

Also see combined categories:
All Module 0.8 Spur Gears
All Metal Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 2024 aluminium

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Aluminium.

There is also a good range of Gears - Spur - Module 0.8 - Aluminium on the Small Parts and Bearings website.


Gears - Spur - Module 0.8 - Plastic
Gears - Spur - Module 0.8 - Plastic

Also see combined categories:
All Module 0.8 Spur Gears
All Plastic Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Plastic.

There is also a good range of Gears - Spur - Module 0.8 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 0.8 - Stainless
Gears - Spur - Module 0.8 - Stainless

Also see combined categories:
All Module 0.8 Spur Gears
All Metal Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Stainless.

There is also a good range of Gears - Spur - Module 0.8 - Stainless on the Small Parts and Bearings website.


Gears - Spur - Module 1.25 - Stainless
Gears - Spur - Module 1.25 - Stainless

Also see combined categories:
All Module 1.25 Spur Gears
All Metal Module 1.25 Spur Gears

PCD = No. of Teeth x 1.250mm. 20o Pressure Angle. 303 stainless steel

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 1.25 - Stainless.

There is also a good range of Gears - Spur - Module 1.25 - Stainless on the Small Parts and Bearings website.


Gears - Spur - Module 1.5 - Plastic
Gears - Spur - Module 1.5 - Plastic

Also see combined categories:
All Module 1.5 Spur Gears
All Plastic Module 1.5 Spur Gears

PCD = No. of Teeth x 1.500mm. 20o Pressure Angle. Acetal and Nylon

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 1.5 - Plastic.

There is also a good range of Gears - Spur - Module 1.5 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 1 - Plastic
Gears - Spur - Module 1 - Plastic

Also see combined categories:
All Module 1.0 Spur Gears
All Plastic Module 1.0 Spur Gears

PCD = No. of Teeth x 1.000mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 1 - Plastic.

There is also a good range of Gears - Spur - Module 1 - Plastic on the Small Parts and Bearings website.


Gears - Spur - Module 3 - Plastic
Gears - Spur - Module 3 - Plastic

Also see combined categories:
All Module 3.0 Spur Gears

PCD = No. of Teeth x 3.000mm. 20o Pressure Angle. Nylon

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 3 - Plastic.

There is also a good range of Gears - Spur - Module 3 - Plastic on the Small Parts and Bearings website.


Gears Metric Mitre


Gears - Mitre - Module 1 - Zinc Diecast
Gears - Mitre - Module 1 - Zinc Diecast

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 1 - Zinc Diecast.

Related Information:

There is also a good range of Gears - Mitre - Module 1 - Zinc Diecast on the Small Parts and Bearings website.


Gears - Mitre - Module 2 - Zinc Diecast
Gears - Mitre - Module 2 - Zinc Diecast

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 2 - Zinc Diecast.

Related Information:

There is also a good range of Gears - Mitre - Module 2 - Zinc Diecast on the Small Parts and Bearings website.


Gears Metric Spiral Mitre


Gears - Mitre - Spiral - Module 1.5 - Steel
Gears - Mitre - Spiral - Module 1.5 - Steel

Also see combined categories:
All Metric Mitre Gears
All Metric Spiral Mitre Gears

1:1 Ratio. 20o Pressure Angle - 35o Spiral tooth - Steel.

A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Spiral - Module 1.5 - Steel.

Related Information:

There is also a good range of Gears - Mitre - Spiral - Module 1.5 - Steel on the Small Parts and Bearings website.


Gears - Mitre - Spiral - Module 3.5 - Steel
Gears - Mitre - Spiral - Module 3.5 - Steel

Also see combined categories:
All Metric Mitre Gears
All Metric Spiral Mitre Gears

1:1 Ratio. 20o Pressure Angle - 35o Spiral tooth - Steel.

A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Spiral - Module 3.5 - Steel.

There is also a good range of Gears - Mitre - Spiral - Module 3.5 - Steel on the Small Parts and Bearings website.


Gears Metric Spur


Gears - Spur - Module 0.4 - Plastic with Insert
Gears - Spur - Module 0.4 - Plastic with Insert

Also see combined categories:
All Module 0.4 Spur Gears
All Plastic Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.4 - Plastic with Insert.

There is also a good range of Gears - Spur - Module 0.4 - Plastic with Insert on the Small Parts and Bearings website.


Gears - Spur - Module 0.5 - Plastic with Insert
Gears - Spur - Module 0.5 - Plastic with Insert

Also see combined categories:
All Module 0.5 Spur Gears
All Plastic Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.5 - Plastic with Insert.

There is also a good range of Gears - Spur - Module 0.5 - Plastic with Insert on the Small Parts and Bearings website.


Gears - Spur - Module 0.8 - Plastic with Insert
Gears - Spur - Module 0.8 - Plastic with Insert

Also see combined categories:
All Module 0.8 Spur Gears
All Plastic Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Plastic with Insert.

There is also a good range of Gears - Spur - Module 0.8 - Plastic with Insert on the Small Parts and Bearings website.


Gears Metric Worms


Worm Gears - Module 1.5 Series 3 - Plastic and Metallic - Right Hand
Worm Gears - Module 1.5 Series 3 - Plastic and Metallic - Right Hand

Also see combined categories:
All Worm Gears
All Metric Worm Gears

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 6.90o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Related Information:

There is also a good range of Worm Gears - Module 1.5 Series 3 - Plastic and Metallic - Right Hand on the Small Parts and Bearings website.


Worm Gears - Module 1 Series 1 - Plastic and Metallic - Left Hand
Worm Gears - Module 1 Series 1 - Plastic and Metallic - Left Hand

Also see combined categories:
All Worm Gears
All Metric Worm Gears

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Related Information:

There is also a good range of Worm Gears - Module 1 Series 1 - Plastic and Metallic - Left Hand on the Small Parts and Bearings website.


Worm Gears - Module 1 Series 1 - Plastic and Metallic - Right Hand
Worm Gears - Module 1 Series 1 - Plastic and Metallic - Right Hand

Also see combined categories:
All Worm Gears
All Metric Worm Gears

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Related Information:

There is also a good range of Worm Gears - Module 1 Series 1 - Plastic and Metallic - Right Hand on the Small Parts and Bearings website.


You may also be interested in

Couplings Helical and Slit


Couplings - Helical - Economy
Couplings - Helical - Economy

Also see combined categories:
All Helical and Slit Couplings

Low cost aluminium couplings primarily used for 3D printer stepper motors

Max. Ang Misalignment 5o. Max Parallel Offset 0.25mm. This category may be available in the new MBA online store at Couplings - Helical - Economy.

Related Information:

There is also a good range of Couplings - Helical - Economy on the Small Parts and Bearings website.


Couplings - Helical - Standard
Couplings - Helical - Standard

Also see combined categories:
All Helical and Slit Couplings

0.1 to 16.2 Nm.

Zero backlash. Max. Ang Misalignment 5o. Max Parallel Offset 0.25mm. This category may be available in the new MBA online store at Couplings - Helical - Standard.

Related Information:

There is also a good range of Couplings - Helical - Standard on the Small Parts and Bearings website.


Couplings - Slit Type - Standard
Couplings - Slit Type - Standard

Also see combined categories:
All Helical and Slit Couplings

Aluminium - Stainless Steel - Flexible - Zero Backlash. 0.1 to 35 Nm. 2400 to 48000 rpm.

High Torsional Stiffness. Zero Backlash. This category may be available in the new MBA online store at Couplings - Slit Type - Standard.

Related Information:

There is also a good range of Couplings - Slit Type - Standard on the Small Parts and Bearings website.


Couplings - Reli-a-flex - Long Series - Clamp Type
Couplings - Reli-a-flex - Long Series - Clamp Type

Also see combined categories:
All Helical and Slit Couplings

From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).

Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.

Related Information:

There is also a good range of Couplings - Reli-a-flex - Long Series - Clamp Type on the Small Parts and Bearings website.


Couplings - Reli-a-flex - Short Series - Clamp Type
Couplings - Reli-a-flex - Short Series - Clamp Type

Also see combined categories:
All Helical and Slit Couplings

From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).

Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.

Related Information:

There is also a good range of Couplings - Reli-a-flex - Short Series - Clamp Type on the Small Parts and Bearings website.


Couplings - Reli-a-flex - Short Series - Set Screw Type
Couplings - Reli-a-flex - Short Series - Set Screw Type

Also see combined categories:
All Helical and Slit Couplings

From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).

Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.

Related Information:

There is also a good range of Couplings - Reli-a-flex - Short Series - Set Screw Type on the Small Parts and Bearings website.


Couplings - Spiral Beam - 6 Beam - Aluminium - Set Screw Type
Couplings - Spiral Beam - 6 Beam - Aluminium - Set Screw Type

Also see combined categories:
All Helical and Slit Couplings

Pilot Bore size not toleranced. Finished Bore sizes to +0.03/0.00. This category may be available in the new MBA online store at Couplings - Spiral Beam - 6 Beam - Aluminium - Set Screw Type.

Related Information:

There is also a good range of Couplings - Spiral Beam - 6 Beam - Aluminium - Set Screw Type on the Small Parts and Bearings website.


Couplings - Slit Type - 4 Slit Miniature - Set Screw Type - Aluminium
Couplings - Slit Type - 4 Slit Miniature - Set Screw Type - Aluminium

Also see combined categories:
All Helical and Slit Couplings

Aluminium - Flexible.


There is also a good range of Couplings - Slit Type - 4 Slit Miniature - Set Screw Type - Aluminium on the Small Parts and Bearings website.


Cable


Attachments - Cable - Eyes
Attachments - Cable - Eyes

Also see combined categories:
All Synchromesh Attachments

Use with synchromesh or standard miniature cable

Recommended dimensions after crimping:. 1.05 Cable - A=2.59. 2.06 Cable - A=2.64. 2.60 Cable - A=2.72. 3.40 Cable - A=2.80 (3.40 Cable must have outer helical wire removed prior to crimping).

Related Information:

There is also a good range of Attachments - Cable - Eyes on the Small Parts and Bearings website.


Leadscrews


Leadscrews - Metric - Rolled Thread - Stainless Steel
Leadscrews - Metric - Rolled Thread - Stainless Steel

Also see combined categories:
All Metric Leadscrews

Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.

Stainless steel. For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.

Related Information:


Pins Taper


Pins - Taper - Metric - Carbon Steel
Pins - Taper - Metric - Carbon Steel

Also see combined categories:
All Metric Taper Pins

Metric Sizes Tapered 1:50. DIN 1 - A - Ground Ra 0.8um

Metric Sizes to DIN 1. This category may be available in the new MBA online store at Pins - Taper - Metric - Carbon Steel.

Related Information:

There is also a good range of Pins - Taper - Metric - Carbon Steel on the Small Parts and Bearings website.


Pins - Taper - Metric - Extractable - External Thread
Pins - Taper - Metric - Extractable - External Thread

Also see combined categories:
All Metric Taper Pins

Metric Sizes Tapered 1:50 and threaded externally for easy extraction.

DIN 7977. This category may be available in the new MBA online store at Pins - Taper - Metric - Extractable - External Thread.

Related Information:

There is also a good range of Pins - Taper - Metric - Extractable - External Thread on the Small Parts and Bearings website.


Pins - Taper - Metric - Extractable - Internal Thread
Pins - Taper - Metric - Extractable - Internal Thread

Also see combined categories:
All Metric Taper Pins

Metric Sizes Tapered 1:50 and threaded internally for easy extraction.

DIN 7978. This category may be available in the new MBA online store at Pins - Taper - Metric - Extractable - Internal Thread.

Related Information:

There is also a good range of Pins - Taper - Metric - Extractable - Internal Thread on the Small Parts and Bearings website.


Pins - Taper - Metric - Stainless Steel
Pins - Taper - Metric - Stainless Steel

Also see combined categories:
All Metric Taper Pins

Metric Sizes Tapered 1:50. DIN 1 - A - Ground Ra 0.8um

Metric Sizes to DIN 1. This category may be available in the new MBA online store at Pins - Taper - Metric - Stainless Steel.

Related Information:

There is also a good range of Pins - Taper - Metric - Stainless Steel on the Small Parts and Bearings website.


Leadscrews


Leadscrew Nuts - Metric - Round - Metallic
Leadscrew Nuts - Metric - Round - Metallic

Also see combined categories:
All Leadscrew Nuts
All Metric Leadscrew Nuts

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: KSM = Carbon Manganese Steel S300 Pb (11 SMn Pb37) / LRM = Bronze CuSn8P. Carbon Manganese steel can be welded but difficulties may arise with bubbling due to sulphur content. KSM: Manual control control only - low rotational speeds only - for clamping or locking functions - for receiving dead weights. LRM: Manual or powered control - low and medium rotational speeds - for working under load. For power transmission and continuous use always use bronze nuts not steel.

Related Information:

There is also a good range of Leadscrew Nuts - Metric - Round - Metallic on the Small Parts and Bearings website.


Leadscrew Nuts - Metric - Square - Metallic
Leadscrew Nuts - Metric - Square - Metallic

Also see combined categories:
All Leadscrew Nuts
All Metric Leadscrew Nuts

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.

Related Information:

There is also a good range of Leadscrew Nuts - Metric - Square - Metallic on the Small Parts and Bearings website.


Springs Die


Springs - Die - Metric - Extra Heavy Duty
Springs - Die - Metric - Extra Heavy Duty

Also see combined categories:
All Metric Die Springs
All All Die Springs

Colour coded yellow

High tensile strength chromium alloy steels. Heat Resistance: Up to +230oC (Loss of load occurs above +120oC). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length. This category may be available in the new MBA online store at Springs - Die - Metric - Extra Heavy Duty.

Related Information:

There is also a good range of Springs - Die - Metric - Extra Heavy Duty on the Small Parts and Bearings website.


Springs - Die - Metric - Heavy Duty
Springs - Die - Metric - Heavy Duty

Also see combined categories:
All Metric Die Springs
All All Die Springs

Colour coded red

High tensile strength chromium alloy steels. Heat Resistance: Up to +230oC (Loss of load occurs above +120oC). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length. This category may be available in the new MBA online store at Springs - Die - Metric - Heavy Duty.

Related Information:

There is also a good range of Springs - Die - Metric - Heavy Duty on the Small Parts and Bearings website.


Springs - Die - Metric - Light Duty
Springs - Die - Metric - Light Duty

Also see combined categories:
All Metric Die Springs
All All Die Springs

Colour coded green

High tensile strength chromium alloy steels. Heat Resistance: Up to +230oC (Loss of load occurs above +120oC). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length. This category may be available in the new MBA online store at Springs - Die - Metric - Light Duty.

Related Information:

There is also a good range of Springs - Die - Metric - Light Duty on the Small Parts and Bearings website.





Main Pages

5 Axis Machine Tool Bearings About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Charity Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Distributor Locations Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Satellite Reaction Wheels Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 212690 products in 2107 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 212690 products in 2107 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.