Dual Vee Tracks Without Mounting Holes Stainless Steel Categories
Dual Vee Bearings
Dual Vee - Tracks without Mounting Holes - Stainless Steel
Vee guide rails for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
Related Information:
There is also a good range of Dual Vee - Tracks without Mounting Holes - Stainless Steel on the Small Parts and Bearings website.
Dual Vee - Tracks with Mounting Holes - Stainless Steel
Vee guide rails for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
Related Information:
There is also a good range of Dual Vee - Tracks with Mounting Holes - Stainless Steel on the Small Parts and Bearings website.
Dual Vee - Tracks without Mounting Holes - Steel
Vee guide rails for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
Related Information:
There is also a good range of Dual Vee - Tracks without Mounting Holes - Steel on the Small Parts and Bearings website.
Dual Vee - Tracks with Mounting Holes - Steel
Vee guide rails for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
Related Information:
There is also a good range of Dual Vee - Tracks with Mounting Holes - Steel on the Small Parts and Bearings website.
Springs - Constant Force
301 Stainless Steel
Mounting hole specifications will be supplied on request. These springs are usually mounted on a drum and the free end attached to a loading force like a counterbalance. Free ID may vary to meet load specification. Load capacity can be increased by using multiple strips in tandem, back to back or laminated. Be sure to leave at least 40mm coiled on the drum at full extension. The spring ID will wrap tightly on the drum so that most applications require no fastening to the drum.
Related Information:
There is also a good range of Springs - Constant Force on the Small Parts and Bearings website.
Mounts - Leveling - Studded - Hygienic - Anchoring - One Mounting Hole
Levelling adjusters. ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications.
Operating temperature -20 to 100o C. Rubber base meets FDA 177-2600. 5o swivel for good floor contact.
There is also a good range of Mounts - Leveling - Studded - Hygienic - Anchoring - One Mounting Hole on the Small Parts and Bearings website.
Mounts - Leveling - Studded - Hygienic - Anchoring - Two Mounting Hole
Levelling adjusters. ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications.
Operating temperature -20 to 100o C. Rubber base meets FDA 177-2600. 5o swivel for good floor contact.
There is also a good range of Mounts - Leveling - Studded - Hygienic - Anchoring - Two Mounting Hole on the Small Parts and Bearings website.
Rail Systems - Miniature Profile
Ideal for precision applications where mounting space is limited
Gothic arch grooves at raceway contacts enables slide to sustain loads & movement from any direction. Made from stainless steel or plastic for corrosion resistance. End caps have oil holes for easy relubrication.
There is also a good range of Rail Systems - Miniature Profile on the Small Parts and Bearings website.
Plungers - Indexing - Non Locking - Without Knob - 303 Stainless Steel
Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.
303 Stainless Steel.
There is also a good range of Plungers - Indexing - Non Locking - Without Knob - 303 Stainless Steel on the Small Parts and Bearings website.
Collars - Threaded - Clamp Type - Stainless Steel
Offer full radial holding power without marring the shaft.
Related Information:
There is also a good range of Collars - Threaded - Clamp Type - Stainless Steel on the Small Parts and Bearings website.
Snap Rings - Internal - Stainless Steel
Internal snaprings are similar to an internal circlip without the lugs
301 S11/S22 Stainless Steel. Used on the inside bore diameter of a housing or similar.
There is also a good range of Snap Rings - Internal - Stainless Steel on the Small Parts and Bearings website.
Snap Rings - External - Stainless Steel
Includes series M3200 / SP / ESP / M2400 / SW snaprings. Similar to a circlip without the lugs.
301 S11/S22 Stainless Steel. Used on the outside diameter of a bearing, shaft or similar equipment.
Cam Followers - Roller Type - Stainless Steel
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
Related Information:
There is also a good range of Cam Followers - Roller Type - Stainless Steel on the Small Parts and Bearings website.
Inserts - Self Tapping - For Plastics - Stainless Steel
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Use of installation tool recommended. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Standard made from 303 stainless steel. Quantity orders can also be supplied in Brass or 316 Stainless.
Related Information:
There is also a good range of Inserts - Self Tapping - For Plastics - Stainless Steel on the Small Parts and Bearings website.
Inserts - Self Tapping - For Aluminium - Stainless 303
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.
Related Information:
There is also a good range of Inserts - Self Tapping - For Aluminium - Stainless 303 on the Small Parts and Bearings website.
Inserts - Self Tapping - For Aluminium - Stainless 316
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or hard plastics. Made from 316 stainless steel.
Related Information:
There is also a good range of Inserts - Self Tapping - For Aluminium - Stainless 316 on the Small Parts and Bearings website.
Knobs - Thumb - With Cap Screw
Four types and four colours.
Complete with high tensile alloy steel screw. If stainless steel screws required please order cap screws separately and knobs without screw.
Related Information:
There is also a good range of Knobs - Thumb - With Cap Screw on the Small Parts and Bearings website.
Pins - Split - Stainless Steel
Split pins.
Hole size indicated is maximum for the pin to be effective. If the pin you require is not available, you may be able to use the next larger diameter so long as the pin is smaller than your hole size. Longer lengths may be cut back to a suitable length.
Related Information:
There is also a good range of Pins - Split - Stainless Steel on the Small Parts and Bearings website.
Clamps - Lorenz
Patented quick clamp is ideal for door openings on bins, hoppers, tanks and manholes. T-Handle allows torque without tools. The one piece unit is made from highly polished 304 stainless steel.
Full 50.8mm adjustment. 180o pivot when disengaged leaving access doorway unobstructed. Will not loosen through vibration. Brackets supplied for easy installation.
There is also a good range of Clamps - Lorenz on the Small Parts and Bearings website.
Gearheads - Inline - Planetary - Size 17 - Precision
Use with NEMA Size 17 Motors.
Stainless Steel housing - Heat Treated Steel Gears - Sealed ball bearings - Aluminium mounting flange. Shaft loading 25.4kg (57 lbs) radial and 24.5kg (55 lbs) axial / Maximum input speed 6500 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 6 arc min, Double Stage : 10 arc min. Operating Temperature : -54 to 121 oC (-65 to 250 Deg F).
Related Information:
There is also a good range of Gearheads - Inline - Planetary - Size 17 - Precision on the Small Parts and Bearings website.
Inserts - Expansion - Press In - 303 Stainless Steel
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.
There is also a good range of Inserts - Expansion - Press In - 303 Stainless Steel on the Small Parts and Bearings website.
Gear Racks - 96DP - Stainless - Side Holes
20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
96 DP. Approx 0.83mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths.
There is also a good range of Gear Racks - 96DP - Stainless - Side Holes on the Small Parts and Bearings website.
Pins - Ball Lock - Keyring Style - 300 Grade Stainless Steel - Dual Ball
Quick release. Provide positive locking for all types of applications and equipment. Body, head and all internal components are made from corrosion resistant stainless steel.
Positive lock detent pins. 300 Grade Stainless Handles. 300 Grade Stainless Components. 440C Stainless Balls.
Related Information:
There is also a good range of Pins - Ball Lock - Keyring Style - 300 Grade Stainless Steel - Dual Ball on the Small Parts and Bearings website.
Pins - Hammer Drive - Round Head - Stainless Steel
Used to replace screws where the need to remove the pin is unlikely.
Stainless Steel 304 Grade. Simple, low cost assembly. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
Related Information:
There is also a good range of Pins - Hammer Drive - Round Head - Stainless Steel on the Small Parts and Bearings website.
Bumpers - Square and Rectangle - Steel Plated - Neoprene
With drilled and counterbored holes for mounting. Neoprene bonded to steel plate.
There is also a good range of Bumpers - Square and Rectangle - Steel Plated - Neoprene on the Small Parts and Bearings website.
Bumpers - Square and Rectangle - Steel Plated - Urethane
With drilled and counterbored holes for mounting. Urethane bonded to steel plate.
There is also a good range of Bumpers - Square and Rectangle - Steel Plated - Urethane on the Small Parts and Bearings website.
Mounts - Leveling - Socket - Nylon - No Lag Holes
Levelling adjusters. Steel and stainless steel socket internal threads. Use your own custom thread length.
Related Information:
There is also a good range of Mounts - Leveling - Socket - Nylon - No Lag Holes on the Small Parts and Bearings website.
Mounts - Leveling - Studded - Nylon - With Lag Holes
Levelling adjusters. Steel and stainless steel threads.
There is also a good range of Mounts - Leveling - Studded - Nylon - With Lag Holes on the Small Parts and Bearings website.
Bumpers - Square and Rectangle
With drilled and counterbored holes for mounting. Neoprene only, no steel plate.
There is also a good range of Bumpers - Square and Rectangle on the Small Parts and Bearings website.
Bearings - Self Clinching - Self Aligning - Stainless and Delrin -tm-
Spyraflo acetal bearings in a special stainless steel self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information. +/- 5% Static Alignment. See animation link at bottom of web page. Panel material no harder than RB65/RB75. Panel hole to be punched or machined to size A (+0.07/-0.00mm).
Related Information:
There is also a good range of Bearings - Self Clinching - Self Aligning - Stainless and Delrin -tm- on the Small Parts and Bearings website.
Dual Vee - Adaptor Bushings
Vee grooved track roller bushings.
Stationary bushings have a concentric hole. Adjustable bushings have an eccentric hole allowing positioning of the guide wheel as the bush is turned.
Related Information:
There is also a good range of Dual Vee - Adaptor Bushings on the Small Parts and Bearings website.
Linear Slide Assemblies - Ball - Pre-Loaded - Compliant
Pre-loaded ball slides provide an acceptable level of accuracy of 0.001mm per mm for most linear motion applications. Considerably lower cost than crossed roller slides.
Uses a conventional hardened steel rod raceway and balls. Incorporates an elastomer spine and shock absorbing backup gib. Provides even and continuous preload, whilst minimising the effects of impact and shock. Tolerant to contamination and can operate of millions of cycles without lubrication. 8-32 UNC mounting holes.
There is also a good range of Linear Slide Assemblies - Ball - Pre-Loaded - Compliant on the Small Parts and Bearings website.
Inserts - Thread Repair - EZ-Lok - Solid Stainless Steel
Easy to install with a standard tap, bolt and wrench.
Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Simply drill and tap the hole to suit the external thread. Install with a bolt and wrench. Metric, UNC and UNF.
Related Information:
There is also a good range of Inserts - Thread Repair - EZ-Lok - Solid Stainless Steel on the Small Parts and Bearings website.
Catches - Snap In Style - Grabber -tm-
Fast economical installation.
Fits frames from 1.1 to 7.1mm thick. Installation hole size 15mm x 39.9mm. Push to close and pull to open. Spring loaded over centre action. Corrosion resistant black ABS with 303 stainless steel spring.
There is also a good range of Catches - Snap In Style - Grabber -tm- on the Small Parts and Bearings website.
Slides - Linear - Recirculating Ball - Standard
The BSR precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100oC (Constant), +120oC (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants. Note BSR1530SL and BSR2040SL can not be mounted from inside of track rail.
There is also a good range of Slides - Linear - Recirculating Ball - Standard on the Small Parts and Bearings website.
Plungers - Indexing - Grip - Stainless - Without Nut
Grip is held in a notch in the fully retracted position. In this position the locking pin does not project from the body at all.
There is also a good range of Plungers - Indexing - Grip - Stainless - Without Nut on the Small Parts and Bearings website.
Bearings - Linear - Sliding - Stainless - PTFE - Closed
Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.
Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000.
There is also a good range of Bearings - Linear - Sliding - Stainless - PTFE - Closed on the Small Parts and Bearings website.
Bearings - Linear - Sliding - Stainless - PTFE - Open
Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.
Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000.
There is also a good range of Bearings - Linear - Sliding - Stainless - PTFE - Open on the Small Parts and Bearings website.
Slides - Linear - Non Recirculating Ball - Standard
The BSP precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100oC (Constant), +120oC (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants.
There is also a good range of Slides - Linear - Non Recirculating Ball - Standard on the Small Parts and Bearings website.
Rail Supports - Without Shaft
For mounting of linear shafting.
Shafting sold separately. Support is made from aluminium.
Related Information:
There is also a good range of Rail Supports - Without Shaft on the Small Parts and Bearings website.
Inserts - Expansion - Press In - 303 Stainless - Flanged
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.
There is also a good range of Inserts - Expansion - Press In - 303 Stainless - Flanged on the Small Parts and Bearings website.
Linear Slides - MiniVee - Track - Hardened Steel
Use with MiniVee carriages and support washers
Low profile miniature linear slide system ideal for semi-conductor, laboratory, medical and packaging applications. Non actuated MiniVee linear slide consists of one or more 6061-T6 anodised aluminium wheel carriages with Dual Vee integrated wheels. Double edged track from 165 to 927mm. Carriages and track sold separately.
Related Information:
There is also a good range of Linear Slides - MiniVee - Track - Hardened Steel on the Small Parts and Bearings website.
Linear Slides - MiniVee - Track - Unhardened Steel
Use with MiniVee carriages and support washers
Low profile miniature linear slide system ideal for semi-conductor, laboratory, medical and packaging applications. Non actuated MiniVee linear slide consists of one or more 6061-T6 anodised aluminium wheel carriages with Dual Vee integrated wheels. Double edged track from 165 to 927mm. Carriages and track sold separately.
Related Information:
There is also a good range of Linear Slides - MiniVee - Track - Unhardened Steel on the Small Parts and Bearings website.
Mounts - Leveling - Studded - Hygienic - Anchoring - Low Profile - High Swivel
Levelling adjusters. ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications.
Operating temperature -20 to 100o C. Wrench flats in thread still allow for full use of threaded section. 12o articulating swivel. 2 bolt holes in base allows for anchoring.
There is also a good range of Mounts - Leveling - Studded - Hygienic - Anchoring - Low Profile - High Swivel on the Small Parts and Bearings website.
Mounts - Pivotal Levelers - Base Without Stud
Tough bonded neoprene. Patented pivotal leveler keeps equipment level and dampens an average 85% of noise. Adjusters.
The mounting nut which holds the stud is molded into the pad in a steel bracket and rotates freely permitting at least 6.35mm of leveling. No stud included so you can use your own custom stud.
Related Information:
There is also a good range of Mounts - Pivotal Levelers - Base Without Stud on the Small Parts and Bearings website.
Linear Slide Assemblies - Ball - Pre-Loaded - Hard Gib
Pre-loaded ball slides provide an acceptable level of accuracy of 0.001mm per mm for most linear motion applications. Considerably lower cost than crossed roller slides.
Hard gib preload. Tolerant to contamination and can operate of millions of cycles without lubrication. 8-32 UNC mounting holes.
There is also a good range of Linear Slide Assemblies - Ball - Pre-Loaded - Hard Gib on the Small Parts and Bearings website.
Sprockets - 3.75 x 1.6mm - Simplex - Plastic
Nylon - Acetal - With and without bore inserts.
Match with series 3.75mm miniature plastic or stainless chain.
Related Information:
There is also a good range of Sprockets - 3.75 x 1.6mm - Simplex - Plastic on the Small Parts and Bearings website.
Balls - Stainless Steel - 304 Grade
A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000 oC.
Related Information:
There is also a good range of Balls - Stainless Steel - 304 Grade on the Small Parts and Bearings website.
Balls - Stainless Steel - 316 Grade
A4 Grade. Very low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000 oC.
Related Information:
There is also a good range of Balls - Stainless Steel - 316 Grade on the Small Parts and Bearings website.
Balls - Stainless Steel - 316L Grade
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.
Related Information:
There is also a good range of Balls - Stainless Steel - 316L Grade on the Small Parts and Bearings website.
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Clearance Items List
Contact Us
Charity
Dental Bearings
Distributor Locations
China
Dowel Pins
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)
Miniature Bearings Australia offers 126929 products in 2255 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.
Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.
