Miniature Bearings Australia Pty Ltd

Bearings Stainless Special Grades Categories


Bearings - Ball - AISI304 Stainless Steel
Bearings - Ball - AISI304 Stainless Steel

Also see combined categories:
All 300 Grade Stainless Bearings

Corrosion and Heat resistance - Non Magnetic - Non Hardenable. Quality Japanese manufacture.

Tolerances differ from standard bearing types - see below. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. ID +0.05 / -0 mm , OD +0 / -0.03 mm up to 10mm bore, Width +0/- 0.12 mm. Mid range speed and load between 304 stainless and 440C stainless. Rubber seals are Nitrile but fluorine rubber may be available on request. Cages, balls, races and shields from AISI 304 Stainless Steel.

Related Information:

A larger range of Bearings - Ball - AISI304 Stainless Steel might be available on the Bearing Shop Online site.


Bearings - Ball - Anti Corrosion - Special Stainless
Bearings - Ball - Anti Corrosion - Special Stainless

Also see combined categories:
All 300 Grade Stainless Bearings

Higher corrosion resistance than 440C stainless - HRC59 Hardness - Same or higher load than 440C

Ideal for applications with salt spray or chemicals in the pH range 3 to 12. ISC CASSTOP design with special TBN-6H stainless steel. Other sizes available on request. This category may be available in the new MBA online store at Bearings - Ball - Anti Corrosion - Special Stainless.

Related Information:

A larger range of Bearings - Ball - Anti Corrosion - Special Stainless might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - Anti Corrosion - Special Stainless on the Small Parts and Bearings website.


Bearings - Ball - 17-4PH Stainless Steel
Bearings - Ball - 17-4PH Stainless Steel

Also see combined categories:
All 300 Grade Stainless Bearings

Excellent Corrosion and Heat resistance - Hardness is between 300 grades and 400 grades. SUS630 grade.

Standard bearing tolerances. Low load, low speed applications requiring maximum corrosion resistance. Rubber seals are Nitrile but fluorine rubber may be available on request. Cages and shields from AISI 304 Stainless Steel. Balls and races from SUS630 (17-4PH) Stainless Steel.

Related Information:

A larger range of Bearings - Ball - 17-4PH Stainless Steel might be available on the Bearing Shop Online site.


Bearings - Ball - 316 Stainless Steel - Double Row - Open
Bearings - Ball - 316 Stainless Steel - Double Row - Open

Also see combined categories:
All 300 Grade Stainless Bearings

Marine, food and medical grade Stainless Steel - Non Hardenable. Open, easier to lubricate. Water lubrication is ok.

Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. This category may be available in the new MBA online store at Bearings - Ball - 316 Stainless Steel - Double Row - Open.

Related Information:

A larger range of Bearings - Ball - 316 Stainless Steel - Double Row - Open might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - 316 Stainless Steel - Double Row - Open on the Small Parts and Bearings website.


Bearings - Ball - 316 Stainless Steel - Single Row - Open
Bearings - Ball - 316 Stainless Steel - Single Row - Open

Also see combined categories:
All 300 Grade Stainless Bearings

Marine, food and medical grade Stainless Steel - Non Hardenable. Open, easier to lubricate. Water lubrication is ok.

Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. This category may be available in the new MBA online store at Bearings - Ball - 316 Stainless Steel - Single Row - Open.

Related Information:

A larger range of Bearings - Ball - 316 Stainless Steel - Single Row - Open might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - 316 Stainless Steel - Single Row - Open on the Small Parts and Bearings website.


Bearings - Ball - 316 Stainless Steel - Single Row - Sealed
Bearings - Ball - 316 Stainless Steel - Single Row - Sealed

Also see combined categories:
All 300 Grade Stainless Bearings

Marine, food and medical grade Stainless Steel - Non Hardenable. Polyethylene plastic seals.

Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races, greased. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.

Related Information:

A larger range of Bearings - Ball - 316 Stainless Steel - Single Row - Sealed might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - 316 Stainless Steel - Single Row - Sealed on the Small Parts and Bearings website.


Bearings - Ball - 316 Stainless Steel - Single Row - Shielded
Bearings - Ball - 316 Stainless Steel - Single Row - Shielded

Also see combined categories:
All 300 Grade Stainless Bearings

Marine, food and medical grade Stainless Steel - Non Hardenable. 316 stainless steel shields.

Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Stainless steel 316 cage, grade 200 type 316 stainless balls, 316 stainless races, 316 stainless steel shields. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.

Related Information:

A larger range of Bearings - Ball - 316 Stainless Steel - Single Row - Shielded might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - 316 Stainless Steel - Single Row - Shielded on the Small Parts and Bearings website.


You may also be interested in

Shafting Precision Ground


Shafting - Ground - Precision - Stainless 416 Grade Hardened
Shafting - Ground - Precision - Stainless 416 Grade Hardened

Also see combined categories:
All Shafting
All Stainless Shafting

Precision ground shafting. 416 grade. Hardened and recommended for use with precision bearings.

This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 416 Grade Hardened.

Related Information:

A larger range of Shafting - Ground - Precision - Stainless 416 Grade Hardened might be available on the Bearing Shop Online site. There is also a good range of Shafting - Ground - Precision - Stainless 416 Grade Hardened on the Small Parts and Bearings website.


Shafting - Ground - Precision - Stainless 420 Grade Hardened
Shafting - Ground - Precision - Stainless 420 Grade Hardened

Also see combined categories:
All Shafting
All Stainless Shafting

Precision ground shafting. 420 grade. Hardened and recommended for use with precision bearings.

This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 420 Grade Hardened.

Related Information:

A larger range of Shafting - Ground - Precision - Stainless 420 Grade Hardened might be available on the Bearing Shop Online site. There is also a good range of Shafting - Ground - Precision - Stainless 420 Grade Hardened on the Small Parts and Bearings website.


Shafting - Ground - Precision - Stainless 440C Grade Hardened
Shafting - Ground - Precision - Stainless 440C Grade Hardened

Also see combined categories:
All Shafting
All Stainless Shafting

Precision ground shafting. 440C grade. Hardened and recommended for use with precision bearings.

This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 440C Grade Hardened.

Related Information:

A larger range of Shafting - Ground - Precision - Stainless 440C Grade Hardened might be available on the Bearing Shop Online site. There is also a good range of Shafting - Ground - Precision - Stainless 440C Grade Hardened on the Small Parts and Bearings website.


Housings with Bearing


Housings - Bearing - Pillow Block - Thermoplastic with Stainless Bearing
Housings - Bearing - Pillow Block - Thermoplastic with Stainless Bearing


Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.

Food grade. Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC. Bearings are 440C stainless steel. Bushings and grease fittings are 300 grade stainless steel.

A larger range of Housings - Bearing - Pillow Block - Thermoplastic with Stainless Bearing might be available on the Bearing Shop Online site. There is also a good range of Housings - Bearing - Pillow Block - Thermoplastic with Stainless Bearing on the Small Parts and Bearings website.


Housings - Bearing - 3 Bolt Offset - Thermoplastic with Stainless Bearing
Housings - Bearing - 3 Bolt Offset - Thermoplastic with Stainless Bearing


Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.

Food grade. Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC. Bearings are 440C stainless steel. Bushings and grease fittings are 300 grade stainless steel.

A larger range of Housings - Bearing - 3 Bolt Offset - Thermoplastic with Stainless Bearing might be available on the Bearing Shop Online site. There is also a good range of Housings - Bearing - 3 Bolt Offset - Thermoplastic with Stainless Bearing on the Small Parts and Bearings website.


Housings - Bearing - 4 Bolt Flange - Thermoplastic with Stainless Bearing
Housings - Bearing - 4 Bolt Flange - Thermoplastic with Stainless Bearing


Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.

Food grade. Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC. Bearings are 440C stainless steel. Bushings and grease fittings are 300 grade stainless steel.

A larger range of Housings - Bearing - 4 Bolt Flange - Thermoplastic with Stainless Bearing might be available on the Bearing Shop Online site. There is also a good range of Housings - Bearing - 4 Bolt Flange - Thermoplastic with Stainless Bearing on the Small Parts and Bearings website.


Housings - Bearing - Tapped Base - Thermoplastic with Stainless Bearing
Housings - Bearing - Tapped Base - Thermoplastic with Stainless Bearing


Thermoplastic housed units offer a more favourable economic choice. Stainless steel bearings offer a high level of corrosion resistance and all metal parts are made from either 302, 304 or 440C stainless steel.

Operating temperature minus 20 oC to +95 deg C. Thermoplastic hosuings are offwhite and are made from glass reinforced PBT resin. Favourable chemical resistance. Very resistant to moisture absorption. Excellent mechanical, thermal and electrical properties. All sleeves, bushings and grease fittings are 300 grade stainless steel. Food grade.

A larger range of Housings - Bearing - Tapped Base - Thermoplastic with Stainless Bearing might be available on the Bearing Shop Online site. There is also a good range of Housings - Bearing - Tapped Base - Thermoplastic with Stainless Bearing on the Small Parts and Bearings website.


Housings - Bearing - Tapped Base Unit - Stainless
Housings - Bearing - Tapped Base Unit - Stainless


Full stainless steel bearing units are the best solution for hostile chemical washdown applications. All metal bearing insert components are a combination of 302, 304 and 440 stainless steel. Seals are silicone rubber. Grease is H-1 food grade.

Operating temperature minus 20 oC to +120 deg C. Solid 304 stainless housings have a machined base and extremely smooth surface finish, essential for demanding washdown installations. These housings do not experience flaking, cracking or discolouration and are virtually unaffected by scrapes. Bearings are removable. Food grade.

A larger range of Housings - Bearing - Tapped Base Unit - Stainless might be available on the Bearing Shop Online site. There is also a good range of Housings - Bearing - Tapped Base Unit - Stainless on the Small Parts and Bearings website.


Housings - Bearing - 2 Bolt Flange - Thermoplastic with Stainless Bearing
Housings - Bearing - 2 Bolt Flange - Thermoplastic with Stainless Bearing


Thermoplastic housed units offer a more favourable economic choice. Stainless steel bearings offer a high level of corrosion resistance and all metal parts are made from either 302, 304 or 440C stainless steel.

Operating temperature minus 20 oC to +95 deg C. Thermoplastic hosuings are offwhite and are made from glass reinforced PBT resin. Favourable chemical resistance. Very resistant to moisture absorption. Excellent mechanical, thermal and electrical properties. All sleeves, bushings and grease fittings are 300 grade stainless steel. Food Grade.

A larger range of Housings - Bearing - 2 Bolt Flange - Thermoplastic with Stainless Bearing might be available on the Bearing Shop Online site. There is also a good range of Housings - Bearing - 2 Bolt Flange - Thermoplastic with Stainless Bearing on the Small Parts and Bearings website.


Bearings Housings


Housings - Bearing - Pillow Block - Miniature
Housings - Bearing - Pillow Block - Miniature


Spyraflo aluminium pillow block housings mounted with 440C stainless miniature bearings

No more need for expensive engineering of housings to suit your new applications. Fully greased Japanese 440C Grade corrosion resistant stainless steel ball bearings. Double shielded bearings to minimise contamination. This category may be available in the new MBA online store at Housings - Bearing - Pillow Block - Miniature.

Related Information:

A larger range of Housings - Bearing - Pillow Block - Miniature might be available on the Bearing Shop Online site. There is also a good range of Housings - Bearing - Pillow Block - Miniature on the Small Parts and Bearings website.


Hobby Shafting


Shafting - Ground - Hobby - Steel
Shafting - Ground - Hobby - Steel

Also see combined categories:
All Shafting
All Steel Shafting

Silversteel shafting for hobbies. Not suitable for precision bearings.

Suitable for use with plastic gears, bushes, couplings etc. Not recommended for use with precision steel or stainless steel bearings. Some sizes have special features such as serrations or small barbs (noted in description). Unground ends. Ideal for axles in robotic applications and educational projects.

Related Information:


Bearings - 316 Stainless Steel - Spherical OD - For Plastic Housings
Bearings - 316 Stainless Steel - Spherical OD - For Plastic Housings


Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.

Load and speed calculations are for reference only. Testing is recommended.

Related Information:

A larger range of Bearings - 316 Stainless Steel - Spherical OD - For Plastic Housings might be available on the Bearing Shop Online site. There is also a good range of Bearings - 316 Stainless Steel - Spherical OD - For Plastic Housings on the Small Parts and Bearings website.


Bearings - Acetal with Stainless Balls - For Plastic Housings
Bearings - Acetal with Stainless Balls - For Plastic Housings

Also see combined categories:
All Acetal Bearings for Housings

Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.

Load and speed calculations are for reference only. Testing is recommended. This category may be available in the new MBA online store at Bearings - Acetal with Stainless Balls - For Plastic Housings.

Related Information:

A larger range of Bearings - Acetal with Stainless Balls - For Plastic Housings might be available on the Bearing Shop Online site. There is also a good range of Bearings - Acetal with Stainless Balls - For Plastic Housings on the Small Parts and Bearings website.


Bearings - Ball - 440C Stainless
Bearings - Ball - 440C Stainless

Also see combined categories:
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome

Stainless steel radial ball bearings

Standard single row radial ball bearings. Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore. This category may be available in the new MBA online store at Bearings - Ball - 440C Stainless.

Related Information:

A larger range of Bearings - Ball - 440C Stainless might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - 440C Stainless on the Small Parts and Bearings website.


Bearings - Linear - Ball - Stainless Steel - Closed
Bearings - Linear - Ball - Stainless Steel - Closed

Also see combined categories:
All Closed Linear Ball Bearings

Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.

Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous. This category may be available in the new MBA online store at Bearings - Linear - Ball - Stainless Steel - Closed.

Related Information:

A larger range of Bearings - Linear - Ball - Stainless Steel - Closed might be available on the Bearing Shop Online site. There is also a good range of Bearings - Linear - Ball - Stainless Steel - Closed on the Small Parts and Bearings website.


Bearings - Linear - Sliding - Stainless - PTFE - Closed
Bearings - Linear - Sliding - Stainless - PTFE - Closed

Also see combined categories:
All Sliding Linear Bearings

Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.

Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000. This category may be available in the new MBA online store at Bearings - Linear - Sliding - Stainless - PTFE - Closed.

A larger range of Bearings - Linear - Sliding - Stainless - PTFE - Closed might be available on the Bearing Shop Online site. There is also a good range of Bearings - Linear - Sliding - Stainless - PTFE - Closed on the Small Parts and Bearings website.


Bearings - Linear - Sliding - Stainless - PTFE - Open
Bearings - Linear - Sliding - Stainless - PTFE - Open

Also see combined categories:
All Sliding Linear Bearings

Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.

Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000. This category may be available in the new MBA online store at Bearings - Linear - Sliding - Stainless - PTFE - Open.

A larger range of Bearings - Linear - Sliding - Stainless - PTFE - Open might be available on the Bearing Shop Online site. There is also a good range of Bearings - Linear - Sliding - Stainless - PTFE - Open on the Small Parts and Bearings website.


Bearings - Conveyor - Hex Bore - Stainless Steel - Double Row
Bearings - Conveyor - Hex Bore - Stainless Steel - Double Row

Also see combined categories:
All Conveyor Bearings

316 stainless conveyor bearings with plastic cage and plastic hex insert

Loads and Speeds are for reference only. Testing recommended. This category may be available in the new MBA online store at Bearings - Conveyor - Hex Bore - Stainless Steel - Double Row.

A larger range of Bearings - Conveyor - Hex Bore - Stainless Steel - Double Row might be available on the Bearing Shop Online site. There is also a good range of Bearings - Conveyor - Hex Bore - Stainless Steel - Double Row on the Small Parts and Bearings website.


Bearings - Conveyor - Hex Bore - Stainless Steel - Single Row
Bearings - Conveyor - Hex Bore - Stainless Steel - Single Row

Also see combined categories:
All Conveyor Bearings

316 stainless conveyor bearings with plastic cage and plastic hex insert

Loads and Speeds are for reference only. Testing recommended. This category may be available in the new MBA online store at Bearings - Conveyor - Hex Bore - Stainless Steel - Single Row.

A larger range of Bearings - Conveyor - Hex Bore - Stainless Steel - Single Row might be available on the Bearing Shop Online site. There is also a good range of Bearings - Conveyor - Hex Bore - Stainless Steel - Single Row on the Small Parts and Bearings website.


Bearings - Ball - Flanged - 440C Stainless
Bearings - Ball - Flanged - 440C Stainless

Also see combined categories:
All Radial Ball Bearings
All Flanged Ball Bearings

Stainless Steel Bearings with Flanges.

Single row radial ball bearings with flanges. Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore. This category may be available in the new MBA online store at Bearings - Ball - Flanged - 440C Stainless.

Related Information:

A larger range of Bearings - Ball - Flanged - 440C Stainless might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - Flanged - 440C Stainless on the Small Parts and Bearings website.


Bearings - Ball - WIR - 440C Stainless
Bearings - Ball - WIR - 440C Stainless

Also see combined categories:
All Radial Ball Bearings
All Extended Inner Ring Bearings

Stainless Steel Bearings with a Snap Ring on the OD

Single row radial ball bearings with extended inner ring (wide inner ring). Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore. This category may be available in the new MBA online store at Bearings - Ball - WIR - 440C Stainless.

Related Information:

A larger range of Bearings - Ball - WIR - 440C Stainless might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - WIR - 440C Stainless on the Small Parts and Bearings website.


Bearings - Thrust - Ball - Flat - Stainless Steel
Bearings - Thrust - Ball - Flat - Stainless Steel

Also see combined categories:
All Ball Thrust Bearings

3 Piece Thrust Bearings Open Type with Flat Washers

These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at Bearings - Thrust - Ball - Flat - Stainless Steel.

Related Information:

A larger range of Bearings - Thrust - Ball - Flat - Stainless Steel might be available on the Bearing Shop Online site. There is also a good range of Bearings - Thrust - Ball - Flat - Stainless Steel on the Small Parts and Bearings website.


Bearings - Thrust - Ball - Grooved - Stainless Steel
Bearings - Thrust - Ball - Grooved - Stainless Steel

Also see combined categories:
All Ball Thrust Bearings

3 Piece Thrust Bearings Open Type

These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at Bearings - Thrust - Ball - Grooved - Stainless Steel.

Related Information:

A larger range of Bearings - Thrust - Ball - Grooved - Stainless Steel might be available on the Bearing Shop Online site. There is also a good range of Bearings - Thrust - Ball - Grooved - Stainless Steel on the Small Parts and Bearings website.


Bearings - Ball - Flanged - WIR - 440C Stainless
Bearings - Ball - Flanged - WIR - 440C Stainless

Also see combined categories:
All Radial Ball Bearings
All Flanged Ball Bearings with Extended Inner

Stainless Steel Bearings with Flanges.

Single row radial ball bearings with flanges and extended inner rings (wide inner rings). Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore. This category may be available in the new MBA online store at Bearings - Ball - Flanged - WIR - 440C Stainless.

Related Information:

A larger range of Bearings - Ball - Flanged - WIR - 440C Stainless might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - Flanged - WIR - 440C Stainless on the Small Parts and Bearings website.


Bearings - Ball - High Precision - 440C Stainless
Bearings - Ball - High Precision - 440C Stainless

Also see combined categories:
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome

Stainless Steel Bearings - Abec 5 and Abec 7.

Single row radial ball bearings. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive). This category may be available in the new MBA online store at Bearings - Ball - High Precision - 440C Stainless.

Related Information:

A larger range of Bearings - Ball - High Precision - 440C Stainless might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - High Precision - 440C Stainless on the Small Parts and Bearings website.


Bearings - Thrust - Ball - Washers Only - Stainless Steel
Bearings - Thrust - Ball - Washers Only - Stainless Steel

Also see combined categories:
All Ball Thrust Bearing Components

Hardened thrust washers for thrust bearings - ungrooved. Match with thrust ball and retainer or roller type.

Stainless Steel Washers are hardened to HRC38.42. This category may be available in the new MBA online store at Bearings - Thrust - Ball - Washers Only - Stainless Steel.

Related Information:

A larger range of Bearings - Thrust - Ball - Washers Only - Stainless Steel might be available on the Bearing Shop Online site. There is also a good range of Bearings - Thrust - Ball - Washers Only - Stainless Steel on the Small Parts and Bearings website.


Bearings - Ball - Double Row - Angular Contact - Stainless Steel
Bearings - Ball - Double Row - Angular Contact - Stainless Steel

Also see combined categories:
All Double Row Ball Bearings

Double Row Ball Bearings - Angular Contact.

This category may be available in the new MBA online store at Bearings - Ball - Double Row - Angular Contact - Stainless Steel.

Related Information:

A larger range of Bearings - Ball - Double Row - Angular Contact - Stainless Steel might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - Double Row - Angular Contact - Stainless Steel on the Small Parts and Bearings website.


Bearings - Ball - Flanged - High Precision - 440C Stainless
Bearings - Ball - Flanged - High Precision - 440C Stainless

Also see combined categories:
All Radial Ball Bearings
All Flanged Ball Bearings

Stainless Steel Bearings with Flanges - Abec 5 and Abec 7.

Single row radial ball bearings with flanges. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive). This category may be available in the new MBA online store at Bearings - Ball - Flanged - High Precision - 440C Stainless.

Related Information:

A larger range of Bearings - Ball - Flanged - High Precision - 440C Stainless might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - Flanged - High Precision - 440C Stainless on the Small Parts and Bearings website.


Bearings - Acetal - Double Row - with 316 Stainless Steel Balls
Bearings - Acetal - Double Row - with 316 Stainless Steel Balls

Also see combined categories:
All Plastic Ball Bearings
All Plastic Double Row Bearings

Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.

Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 oC to 100 oC Continuous. This category may be available in the new MBA online store at Bearings - Acetal - Double Row - with 316 Stainless Steel Balls.

Related Information:

A larger range of Bearings - Acetal - Double Row - with 316 Stainless Steel Balls might be available on the Bearing Shop Online site. There is also a good range of Bearings - Acetal - Double Row - with 316 Stainless Steel Balls on the Small Parts and Bearings website.


Bearings - Acetal - Single Row - with 302 Stainless Steel Balls
Bearings - Acetal - Single Row - with 302 Stainless Steel Balls

Also see combined categories:
All Plastic Ball Bearings
All Plastic Single Row Bearings

Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.

Races made from Acetal - Balls made from 302 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 oC to 100 oC Continuous. This category may be available in the new MBA online store at Bearings - Acetal - Single Row - with 302 Stainless Steel Balls.

Related Information:

A larger range of Bearings - Acetal - Single Row - with 302 Stainless Steel Balls might be available on the Bearing Shop Online site. There is also a good range of Bearings - Acetal - Single Row - with 302 Stainless Steel Balls on the Small Parts and Bearings website.


Bearings - Acetal - Single Row - with 316 Stainless Steel Balls
Bearings - Acetal - Single Row - with 316 Stainless Steel Balls

Also see combined categories:
All Plastic Ball Bearings
All Plastic Single Row Bearings

Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.

Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 oC to 100 oC Continuous. This category may be available in the new MBA online store at Bearings - Acetal - Single Row - with 316 Stainless Steel Balls.

Related Information:

A larger range of Bearings - Acetal - Single Row - with 316 Stainless Steel Balls might be available on the Bearing Shop Online site. There is also a good range of Bearings - Acetal - Single Row - with 316 Stainless Steel Balls on the Small Parts and Bearings website.


Bearings - Peek - Single Row - with 316 Stainless Steel Balls
Bearings - Peek - Single Row - with 316 Stainless Steel Balls

Also see combined categories:
All Plastic Ball Bearings
All Plastic Single Row Bearings

PEEK (Polyetheretherketone), is a high temperature, high-performance engineering polymer.

Races made from PEEK - Balls made from Ground Glass - Cages from PEEK. PEEK offers chemical and water resistance similar to PPS (Polyphenylene Sulfide) but can operate at higher temperatures. PEEK can be used continuously to 338 Deg F (170 Deg C) and in hot water or steam without permanent loss in physical properties. Wear, Chemical & Hydrolysis Resistant. Exceptional performance over a wide range of temperatures and extreme conditions. Low Smoke and Toxic Gas Emission.

Related Information:

A larger range of Bearings - Peek - Single Row - with 316 Stainless Steel Balls might be available on the Bearing Shop Online site. There is also a good range of Bearings - Peek - Single Row - with 316 Stainless Steel Balls on the Small Parts and Bearings website.


Bearings - PVDF - Single Row - with 316 Stainless Steel Balls
Bearings - PVDF - Single Row - with 316 Stainless Steel Balls

Also see combined categories:
All Plastic Ball Bearings
All Plastic Single Row Bearings

Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.

Races made from PVDF - Balls made from Ground Glass - Cages from PVDF. Kynar -tm- PVDF (Polyvinylidene Fluoride) is a high performance engineering polymer. Kynar -tm- has provided superior chemical resistance properties in critical contact applications for food, pharmaceutical, and semiconductor industries for over 20 years. For chemical and high temperature resistance, low permeability and high mechanical strength. This category may be available in the new MBA online store at Bearings - PVDF - Single Row - with 316 Stainless Steel Balls.

Related Information:

A larger range of Bearings - PVDF - Single Row - with 316 Stainless Steel Balls might be available on the Bearing Shop Online site. There is also a good range of Bearings - PVDF - Single Row - with 316 Stainless Steel Balls on the Small Parts and Bearings website.


Bearings - Ball - WIR - High Precision - 440C Stainless
Bearings - Ball - WIR - High Precision - 440C Stainless

Also see combined categories:
All Radial Ball Bearings
All Extended Inner Ring Bearings

Stainless Steel Bearings - Abec 5 and Abec 7.

Single row radial ball bearings with extended inner ring (wide inner ring). True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive). This category may be available in the new MBA online store at Bearings - Ball - WIR - High Precision - 440C Stainless.

Related Information:

A larger range of Bearings - Ball - WIR - High Precision - 440C Stainless might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - WIR - High Precision - 440C Stainless on the Small Parts and Bearings website.


Bearings - Ball - Flanged - WIR - High Precision - 440C Stainless
Bearings - Ball - Flanged - WIR - High Precision - 440C Stainless

Also see combined categories:
All Radial Ball Bearings
All Flanged Ball Bearings with Extended Inner

Stainless Steel Bearings with Flanges - Abec 5 and Abec 7.

Single row radial ball bearings with flanges and extended inner rings (wide inner rings). True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive). This category may be available in the new MBA online store at Bearings - Ball - Flanged - WIR - High Precision - 440C Stainless.

Related Information:

A larger range of Bearings - Ball - Flanged - WIR - High Precision - 440C Stainless might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - Flanged - WIR - High Precision - 440C Stainless on the Small Parts and Bearings website.


Locknuts - Stainless Insert
Locknuts - Stainless Insert


Simplify the assembly and reduce costs involved in securing ball bearings. One piece item where the locking function is performed by a spring peened into the top of the nut.

Nut Body: Low Carbon Steel. Locking Insert: Stainless Steel Hardness HB 201-269. The spring bears on the flank of the shaft thread with force (P) generating reaction force (P’) in the screw threads with a resulting high friction torque (prevailing torque). Unique slim body design. Secure locking without keyway and tab washer. One piece construction reduces stock and allows simpler, quicker assembly. Simple infinite adjustment. Re-usable up to 100 times. Resists vibration and shock. Equally effective for rotation in either direction even with rapid reversals.

Related Information:

There is also a good range of Locknuts - Stainless Insert on the Small Parts and Bearings website.


Ball Transfer Units - Screw Stem - Stainless - Precision
Ball Transfer Units - Screw Stem - Stainless - Precision

Also see combined categories:
All Screw Fit Ball Transfers

Single ball bearings units for conveyor systems

Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms. This category may be available in the new MBA online store at Ball Transfer Units - Screw Stem - Stainless - Precision.

A larger range of Ball Transfer Units - Screw Stem - Stainless - Precision might be available on the Bearing Shop Online site. There is also a good range of Ball Transfer Units - Screw Stem - Stainless - Precision on the Small Parts and Bearings website.


Dual Vee - Tracks with Mounting Holes - Stainless Steel
Dual Vee - Tracks with Mounting Holes - Stainless Steel

Also see combined categories:
All Dual Vee Tracks

Vee guide rails for vee grooved track roller guide wheels.

Match Track Size with same size Guide Wheel. This category may be available in the new MBA online store at Dual Vee - Tracks with Mounting Holes - Stainless Steel.

Related Information:

A larger range of Dual Vee - Tracks with Mounting Holes - Stainless Steel might be available on the Bearing Shop Online site. There is also a good range of Dual Vee - Tracks with Mounting Holes - Stainless Steel on the Small Parts and Bearings website.


Bearings - Conveyor - Hex Bore - Plastic - Double Row
Bearings - Conveyor - Hex Bore - Plastic - Double Row

Also see combined categories:
All Conveyor Bearings

Plastic hex bore conveyor bearings with 316 stainless balls

Loads and Speeds are for reference only. Testing recommended. This category may be available in the new MBA online store at Bearings - Conveyor - Hex Bore - Plastic - Double Row.

A larger range of Bearings - Conveyor - Hex Bore - Plastic - Double Row might be available on the Bearing Shop Online site. There is also a good range of Bearings - Conveyor - Hex Bore - Plastic - Double Row on the Small Parts and Bearings website.


Bearings - Conveyor - Hex Bore - Plastic - Single Row
Bearings - Conveyor - Hex Bore - Plastic - Single Row

Also see combined categories:
All Conveyor Bearings

Plastic hex bore conveyor bearings with 316 stainless balls

Loads and Speeds are for reference only. Testing recommended. This category may be available in the new MBA online store at Bearings - Conveyor - Hex Bore - Plastic - Single Row.

A larger range of Bearings - Conveyor - Hex Bore - Plastic - Single Row might be available on the Bearing Shop Online site. There is also a good range of Bearings - Conveyor - Hex Bore - Plastic - Single Row on the Small Parts and Bearings website.


Slides - Drawer - Stainless - No Disconnect - Heavy Duty - Full Ext
Slides - Drawer - Stainless - No Disconnect - Heavy Duty - Full Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Positive stop slide that will not disconnect once installed.

There is also a good range of Slides - Drawer - Stainless - No Disconnect - Heavy Duty - Full Ext on the Small Parts and Bearings website.


Slides - Drawer - Stainless - No Disconnect - Medium Duty - Full Ext
Slides - Drawer - Stainless - No Disconnect - Medium Duty - Full Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Positive stop slide that will not disconnect once installed.

There is also a good range of Slides - Drawer - Stainless - No Disconnect - Medium Duty - Full Ext on the Small Parts and Bearings website.


Ball Transfer Units - Flange Mount - Standard - Stainless - Deep
Ball Transfer Units - Flange Mount - Standard - Stainless - Deep

Also see combined categories:
All Flange Mount Ball Transfers

Single ball bearings units for conveyor systems

This category may be available in the new MBA online store at Ball Transfer Units - Flange Mount - Standard - Stainless - Deep.

A larger range of Ball Transfer Units - Flange Mount - Standard - Stainless - Deep might be available on the Bearing Shop Online site. There is also a good range of Ball Transfer Units - Flange Mount - Standard - Stainless - Deep on the Small Parts and Bearings website.





Main Pages

5 Axis Machine Tool Bearings About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Charity Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Distributor Locations Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Satellite Reaction Wheels Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 212690 products in 2107 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 212690 products in 2107 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.