Miniature Bearings Australia Pty Ltd

Bearings Linear


Linear Bearings


Bearings - Linear - Ball - Closed
Bearings - Linear - Ball - Closed

Also see combined categories:
All Closed Linear Ball Bearings

Standard closed type to run on standard 60HRC shafts with h6 tolerances

Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous.

Related Information:
Precision Shafting To Suit Bearings

A larger range of Bearings - Linear - Ball - Closed might be available on the Bearing Shop Online site.

Bearings - Linear - Ball - Miniature - Super High Precision
Bearings - Linear - Ball - Miniature - Super High Precision

Also see combined categories:
All Closed Linear Ball Bearings

High Precision Corrosion Resistant Miniature Linear Bearings.

High Precision Swiss Made, Accurate Guiding, Smooth Running. High Load Capacity. Tolerances --- d (+0.008 / -0.000 mm) D (+0.000 / -0.010 mm). Recommended Outer ring fitted with interferance of 1-3 Microns or retained by Circlips. Shafts (not included) should be 60-63 Rockwell C hardness with tolerances +0.000 / -0.006 mm.

Related Information:
Precision Shafting To Suit Bearings

A larger range of Bearings - Linear - Ball - Miniature - Super High Precision might be available on the Bearing Shop Online site. There is also a good range of Bearings - Linear - Ball - Miniature - Super High Precision on the Small Parts and Bearings website.

Bearings - Linear - Ball - Stainless Steel - Closed
Bearings - Linear - Ball - Stainless Steel - Closed

Also see combined categories:
All Closed Linear Ball Bearings

Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.

Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous.

Related Information:
Precision Shafting To Suit Bearings

A larger range of Bearings - Linear - Ball - Stainless Steel - Closed might be available on the Bearing Shop Online site. There is also a good range of Bearings - Linear - Ball - Stainless Steel - Closed on the Small Parts and Bearings website.

Bearings - Linear - Ball - Thomson Precision Steel - Closed
Bearings - Linear - Ball - Thomson Precision Steel - Closed

Also see combined categories:
All Thomson Linear Ball Bearings

For running on shafts fixed at the ends.

Related Information:
Loads
Precision Shafting To Suit Bearings

A larger range of Bearings - Linear - Ball - Thomson Precision Steel - Closed might be available on the Bearing Shop Online site. There is also a good range of Bearings - Linear - Ball - Thomson Precision Steel - Closed on the Small Parts and Bearings website.

Bearings - Linear - Frelon Gold Lined - Closed - Precision
Bearings - Linear - Frelon Gold Lined - Closed - Precision

Also see combined categories:
All Closed Frelon Lined Linear Bearings
All Closed Frelon Gold Lined Linear Bearings

Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C

Frelon Gold = 20000 PV. Dry Running Max Surface Speed Frelon Gold = 1.5 mtrs / sec (300 ft / min). With Lubrication Max Surface Speed Frelon Gold = 4.1 mtrs / sec (825 ft / min). Interaction of the Frelon Gold material and the shafting creates a microscopic transfer of Frelon Gold to the running surfaces filling the valleys during the initial break-in period. Precision type has closer running clearances.

Related Information:
Technical
Precision Shafting To Suit Bearings

A larger range of Bearings - Linear - Frelon Gold Lined - Closed - Precision might be available on the Bearing Shop Online site. There is also a good range of Bearings - Linear - Frelon Gold Lined - Closed - Precision on the Small Parts and Bearings website.

Bearings - Linear - Frelon Gold Lined - Closed - Standard
Bearings - Linear - Frelon Gold Lined - Closed - Standard

Also see combined categories:
All Closed Frelon Lined Linear Bearings
All Closed Frelon Gold Lined Linear Bearings

Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C

Frelon Gold = 20000 PV. Dry Running Max Surface Speed Frelon Gold = 1.5 mtrs / sec (300 ft / min). With Lubrication Max Surface Speed Frelon Gold = 4.1 mtrs / sec (825 ft / min). Interaction of the Frelon Gold material and the shafting creates a microscopic transfer of Frelon Gold to the running surfaces filling the valleys during the initial break-in period. Standard type has slightly larger running clearances.

Related Information:
Technical
Precision Shafting To Suit Bearings

A larger range of Bearings - Linear - Frelon Gold Lined - Closed - Standard might be available on the Bearing Shop Online site. There is also a good range of Bearings - Linear - Frelon Gold Lined - Closed - Standard on the Small Parts and Bearings website.

Bearings - Linear - Frelon Gold Lined - Open - Precision
Bearings - Linear - Frelon Gold Lined - Open - Precision

Also see combined categories:
All Open Frelon Lined Linear Bearings
All Open Frelon Gold Lined Linear Bearings

Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C

Frelon Gold = 20000 PV. Dry Running Max Surface Speed Frelon Gold = 1.5 mtrs / sec (300 ft / min). With Lubrication Max Surface Speed Frelon Gold = 4.1 mtrs / sec (825 ft / min). Interaction of the Frelon Gold material and the shafting creates a microscopic transfer of Frelon Gold to the running surfaces filling the valleys during the initial break-in period. Precision type has closer running clearances.

Related Information:
Technical
Precision Shafting To Suit Bearings

A larger range of Bearings - Linear - Frelon Gold Lined - Open - Precision might be available on the Bearing Shop Online site. There is also a good range of Bearings - Linear - Frelon Gold Lined - Open - Precision on the Small Parts and Bearings website.

Bearings - Linear - Frelon Gold Lined - Open - Standard
Bearings - Linear - Frelon Gold Lined - Open - Standard

Also see combined categories:
All Open Frelon Lined Linear Bearings
All Open Frelon Gold Lined Linear Bearings

Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C

Frelon Gold = 20000 PV. Dry Running Max Surface Speed Frelon Gold = 1.5 mtrs / sec (300 ft / min). With Lubrication Max Surface Speed Frelon Gold = 4.1 mtrs / sec (825 ft / min). Interaction of the Frelon Gold material and the shafting creates a microscopic transfer of Frelon Gold to the running surfaces filling the valleys during the initial break-in period. Standard type has slightly larger running clearances.

Related Information:
Technical
Precision Shafting To Suit Bearings

A larger range of Bearings - Linear - Frelon Gold Lined - Open - Standard might be available on the Bearing Shop Online site. There is also a good range of Bearings - Linear - Frelon Gold Lined - Open - Standard on the Small Parts and Bearings website.

Bearings - Linear - Frelon J Lined - Closed - Precision
Bearings - Linear - Frelon J Lined - Closed - Precision

Also see combined categories:
All Closed Frelon Lined Linear Bearings
All Closed Frelon J Lined Linear Bearings

Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C

Frelon J = 10000 PV. Dry Running Max Surface Speed Frelon J = 0.7 mtrs / sec (140 ft / min). With Lubrication Max Surface Speed Frelon J = 2 mtrs / sec (400 ft / min). Precision type has closer running clearances.

Related Information:
Technical
Precision Shafting To Suit Bearings

A larger range of Bearings - Linear - Frelon J Lined - Closed - Precision might be available on the Bearing Shop Online site. There is also a good range of Bearings - Linear - Frelon J Lined - Closed - Precision on the Small Parts and Bearings website.

Bearings - Linear - Frelon J Lined - Closed - Standard
Bearings - Linear - Frelon J Lined - Closed - Standard

Also see combined categories:
All Closed Frelon Lined Linear Bearings
All Closed Frelon J Lined Linear Bearings

Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C

Frelon J = 10000 PV. Dry Running Max Surface Speed Frelon J = 0.7 mtrs / sec (140 ft / min). With Lubrication Max Surface Speed Frelon J = 2 mtrs / sec (400 ft / min). Standard type has slightly larger running clearances.

Related Information:
Technical
Precision Shafting To Suit Bearings

A larger range of Bearings - Linear - Frelon J Lined - Closed - Standard might be available on the Bearing Shop Online site. There is also a good range of Bearings - Linear - Frelon J Lined - Closed - Standard on the Small Parts and Bearings website.

Bearings - Linear - Sliding - Ceramic Coated
Bearings - Linear - Sliding - Ceramic Coated

Also see combined categories:
All Sliding Linear Bearings

Approved for direct food contact in applications where animal fat or food approved lubricants are present.

Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Minimum shaft hardness RC35. Max PV 40,000. Temperature range -125 oC to +226 Deg C. Max static PSI 5000.


A larger range of Bearings - Linear - Sliding - Ceramic Coated might be available on the Bearing Shop Online site. There is also a good range of Bearings - Linear - Sliding - Ceramic Coated on the Small Parts and Bearings website.

Bearings - Linear - Sliding - Stainless - PTFE - Closed
Bearings - Linear - Sliding - Stainless - PTFE - Closed

Also see combined categories:
All Sliding Linear Bearings

Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.

Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000.


A larger range of Bearings - Linear - Sliding - Stainless - PTFE - Closed might be available on the Bearing Shop Online site. There is also a good range of Bearings - Linear - Sliding - Stainless - PTFE - Closed on the Small Parts and Bearings website.

Bearings - Linear - Sliding - Stainless - PTFE - Open
Bearings - Linear - Sliding - Stainless - PTFE - Open

Also see combined categories:
All Sliding Linear Bearings

Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.

Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000.


A larger range of Bearings - Linear - Sliding - Stainless - PTFE - Open might be available on the Bearing Shop Online site. There is also a good range of Bearings - Linear - Sliding - Stainless - PTFE - Open on the Small Parts and Bearings website.

Ball Splines Linear


Linear Ball Splines - Bearings - Unflanged
Linear Ball Splines - Bearings - Unflanged

Also see combined categories:
All Linear Ball Splines

Use with Linear Ball Spline Shaft.

Related Information:
Shaft To Suit

There is also a good range of Linear Ball Splines - Bearings - Unflanged on the Small Parts and Bearings website.

Linear Bearings


Seals - For Linear Bearings - Closed
Seals - For Linear Bearings - Closed

Also see combined categories:
All Oil Seals


A larger range of Seals - For Linear Bearings - Closed might be available on the Bearing Shop Online site. There is also a good range of Seals - For Linear Bearings - Closed on the Small Parts and Bearings website.

Seals - For Linear Bearings - Open
Seals - For Linear Bearings - Open

Also see combined categories:
All Oil Seals


A larger range of Seals - For Linear Bearings - Open might be available on the Bearing Shop Online site. There is also a good range of Seals - For Linear Bearings - Open on the Small Parts and Bearings website.

Linear Bearings with Housing


Housings - Linear - Square
Housings - Linear - Square

Also see combined categories:
All Linear Bearing Housings

Used to maintain radial integrity and eliminate the need for parallel shafting.

Bearings are made from 6061-T6 Aluminum with Anodized finished. Equipped with bearing plugs that run on a single shaft. Threaded adjustable plugs are made from 316 Stainless with self-lubricating FrelonJ wear pads.


A larger range of Housings - Linear - Square might be available on the Bearing Shop Online site. There is also a good range of Housings - Linear - Square on the Small Parts and Bearings website.

Linear Bearing Housings


Housings - Linear - Square - Clamps
Housings - Linear - Square - Clamps

Also see combined categories:
All Linear Bearing Housings


A larger range of Housings - Linear - Square - Clamps might be available on the Bearing Shop Online site. There is also a good range of Housings - Linear - Square - Clamps on the Small Parts and Bearings website.

Linear Bearings with Housing


Housings - Linear - Thomson Super Flanged
Housings - Linear - Thomson Super Flanged

Also see combined categories:
All Linear Bearing Housings
All Linear Bearing Housings With Bearing

Includes Bearings.

Related Information:
Thomson Super Smart Overview
Thomson Super Smart Loads

A larger range of Housings - Linear - Thomson Super Flanged might be available on the Bearing Shop Online site. There is also a good range of Housings - Linear - Thomson Super Flanged on the Small Parts and Bearings website.

Housings - Bearing - Flange Mounted - Frelon - Self Aligning
Housings - Bearing - Flange Mounted - Frelon - Self Aligning

Single and double length

Bearing is Frelon Gold -tm- encased in a flanged housing made from 6061-T6 aluminium. Double length has two bearings mounted internally. For rotating and linear motion.


There is also a good range of Housings - Bearing - Flange Mounted - Frelon - Self Aligning on the Small Parts and Bearings website.

Housings - Bearing - Pillow Block - Frelon - Precision - Closed
Housings - Bearing - Pillow Block - Frelon - Precision - Closed

Single and double length

Bearing is Frelon Gold -tm- encased in a flanged housing made from 6061-T6 aluminium. Double length has two bearings mounted internally. For rotating and linear motion.


A larger range of Housings - Bearing - Pillow Block - Frelon - Precision - Closed might be available on the Bearing Shop Online site. There is also a good range of Housings - Bearing - Pillow Block - Frelon - Precision - Closed on the Small Parts and Bearings website.

Housings - Bearing - Pillow Block - Frelon - Precision - Open
Housings - Bearing - Pillow Block - Frelon - Precision - Open

Single and double length

Bearing is Frelon Gold -tm- encased in a flanged housing made from 6061-T6 aluminium. Double length has two bearings mounted internally. For rotating and linear motion.


A larger range of Housings - Bearing - Pillow Block - Frelon - Precision - Open might be available on the Bearing Shop Online site. There is also a good range of Housings - Bearing - Pillow Block - Frelon - Precision - Open on the Small Parts and Bearings website.

Housings - Bearing - Pillow Block - Frelon - Standard - Closed
Housings - Bearing - Pillow Block - Frelon - Standard - Closed

Bearing is Frelon Gold -tm- encased in a flanged housing made from 6061-T6 aluminium. For rotating and linear motion.


A larger range of Housings - Bearing - Pillow Block - Frelon - Standard - Closed might be available on the Bearing Shop Online site. There is also a good range of Housings - Bearing - Pillow Block - Frelon - Standard - Closed on the Small Parts and Bearings website.

Housings - Bearing - Pillow Block - Frelon - Standard - Open
Housings - Bearing - Pillow Block - Frelon - Standard - Open

Bearing is Frelon Gold -tm- encased in a flanged housing made from 6061-T6 aluminium. For rotating and linear motion.


A larger range of Housings - Bearing - Pillow Block - Frelon - Standard - Open might be available on the Bearing Shop Online site. There is also a good range of Housings - Bearing - Pillow Block - Frelon - Standard - Open on the Small Parts and Bearings website.

Drylin Bearings and Systems


Drylin Linear Assembly Parts - Carriage Only
Drylin Linear Assembly Parts - Carriage Only

Also see combined categories:
All Drylin Assembly Parts

Linear sliding motion. Plain and Locking Types. These carriages require a matching guide rail or matching rack and pinion. Match by size.

Drylin(R) T linear guides are maintenance free and run without additional lubrication. Consequently, they are also suitable for use in damp or dirty environments. Available with a manually operated clamp to achieve a force fit at any desired point along the travel path. The wing screw is used to clamp the slide in place of the guide. Matching components listed in separate category.

Related Information:
Technical

There is also a good range of Drylin Linear Assembly Parts - Carriage Only on the Small Parts and Bearings website.

Linear Bearings with Housing


Housings - Linear - Thomson Super Smart Flanged
Housings - Linear - Thomson Super Smart Flanged

Also see combined categories:
All Linear Bearing Housings
All Linear Bearing Housings With Bearing

Includes Bearings.

Related Information:
Thomson Super Smart Overview
Thomson Super Smart Loads

A larger range of Housings - Linear - Thomson Super Smart Flanged might be available on the Bearing Shop Online site. There is also a good range of Housings - Linear - Thomson Super Smart Flanged on the Small Parts and Bearings website.

Drylin Bearings and Systems


Drylin Sliding Bearings
Drylin Sliding Bearings

Linear sliding motion. Use with Drylin Aluminium Shafts.

Sliding film Iglidur J. Maximum Mean Surface Pressure: 25 N/mm2. Highest Wear Resistance at loads: Less than 2 N/mm2. Maximum Speed: 8 m/s (dry) Greater than 10 m/s (lubricated) 1.5 m/s (rotating dry). Working Temp. Range: -60oC to +100oC (increased wear when used in excess of 80oC).

Related Information:
Technical

A larger range of Drylin Sliding Bearings might be available on the Bearing Shop Online site. There is also a good range of Drylin Sliding Bearings on the Small Parts and Bearings website.

Bearings Special Purpose


Bearings - Chamfered Edges
Bearings - Chamfered Edges

Chamfered edge bearings for Linear Guide Systems and pushbikes

Often used in pushbike headsets. Note bearings for pushbikes with two chamfered edges have the chamfer on the inner ring on one side and outer ring on the other - designation CEP.

Related Information:
Precision Shafting To Suit Bearings

A larger range of Bearings - Chamfered Edges might be available on the Bearing Shop Online site. There is also a good range of Bearings - Chamfered Edges on the Small Parts and Bearings website.

Drylin Bearings and Systems


Drylin Linear Assembly Parts - Guide Rails Only
Drylin Linear Assembly Parts - Guide Rails Only

Also see combined categories:
All Drylin Assembly Parts

These rails require a matching carriage as listed in a separate category. Match by size.

Slide Rail: Extruded Aluminium Construction Material: Al Mg Si 0.5. Coating: Hard anodised, 50um Hardness: 500HV. Matching components listed in separate category.

Related Information:
Technical

There is also a good range of Drylin Linear Assembly Parts - Guide Rails Only on the Small Parts and Bearings website.

Drylin - Linear - Slides and Carriages - Size 17
Drylin - Linear - Slides and Carriages - Size 17

Also see combined categories:
All Drylin Slides and Carriages

Linear sliding motion.

Guide Rail Weight: 150 g/m. Carriage Weight: 1.7g. Max Rail Length: 1960 mm. Standard Bore Scheme: Symmetrical C5 = C6. Particularly insensitive to dust, dirt and water.

Related Information:
Technical

There is also a good range of Drylin - Linear - Slides and Carriages - Size 17 on the Small Parts and Bearings website.

Drylin - Linear - Slides and Carriages - Size 27
Drylin - Linear - Slides and Carriages - Size 27

Also see combined categories:
All Drylin Slides and Carriages

Linear sliding motion.

Guide Rail Weight: 290 g/m. Carriage Weight: 10.8 or 12.5g. Max Rail Length: 2000 mm. Standard Bore Scheme: Symmetrical C5 = C6. Particularly insensitive to dust, dirt and water.

Related Information:
Technical

There is also a good range of Drylin - Linear - Slides and Carriages - Size 27 on the Small Parts and Bearings website.

Drylin - Linear - Slides and Carriages - Size 80
Drylin - Linear - Slides and Carriages - Size 80

Also see combined categories:
All Drylin Slides and Carriages

Linear sliding motion.

Guide Rail Weight: 1140 g/m. Carriage Weight: 100g. Max Rail Length: 2000 mm. Standard Bore Scheme: Symmetrical C5 = C6. Particularly insensitive to dust, dirt and water.

Related Information:
Technical

There is also a good range of Drylin - Linear - Slides and Carriages - Size 80 on the Small Parts and Bearings website.

Linear Bearings with Housing


Housings - Linear - Pillow Block - Closed - Ceramic Coated
Housings - Linear - Pillow Block - Closed - Ceramic Coated

Also see combined categories:
All Linear Bearing Housings
All Linear Bearing Housings With Bearing

Approved for direct food contact in applications where animal fat or food approved lubricants are present.

Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. DO NOT USE WD-40 or Silcone based spray lubricants.


A larger range of Housings - Linear - Pillow Block - Closed - Ceramic Coated might be available on the Bearing Shop Online site. There is also a good range of Housings - Linear - Pillow Block - Closed - Ceramic Coated on the Small Parts and Bearings website.

Housings - Linear - Thomson Super Smart Pillow Block - Closed
Housings - Linear - Thomson Super Smart Pillow Block - Closed

Also see combined categories:
All Linear Bearing Housings
All Linear Bearing Housings With Bearing

Includes Bearings.

Related Information:
Thomson Super Smart Overview
Thomson Super Smart Loads

A larger range of Housings - Linear - Thomson Super Smart Pillow Block - Closed might be available on the Bearing Shop Online site. There is also a good range of Housings - Linear - Thomson Super Smart Pillow Block - Closed on the Small Parts and Bearings website.

Linear Slides


Slides - Linear - Cross Roller Rail
Slides - Linear - Cross Roller Rail

Also see combined categories:
All Linear Slides

Compact, precision bearings that can support and guide high loads with high accuracy and repeatability, low friction, and low starting force.

Each consists of a pair of hardened steel ways containing 90 deg V grooves and a row of alternately crossed cylindrical rollers. Installed faced to face on smooth flat and accurately parallel, coplanar or perpendicular surfaces. Lubrication required, light grease for low speeds to continuous oil bath/mist for high speeds.


There is also a good range of Slides - Linear - Cross Roller Rail on the Small Parts and Bearings website.

Drylin Bearings and Systems


Drylin Sliding Film
Drylin Sliding Film

Linear sliding motion. Use with Drylin Aluminium Shafts.

Sliding film Iglidur J.

Related Information:
Technical

There is also a good range of Drylin Sliding Film on the Small Parts and Bearings website.

Clamping Rings


Rings - Retaining - C Type External - For Linear Bearings
Rings - Retaining - C Type External - For Linear Bearings

Fits into the retaining ring grooves on the outside diameter of Super Smart, Super and Precision Linear Bearings to provide external mounting retension.


There is also a good range of Rings - Retaining - C Type External - For Linear Bearings on the Small Parts and Bearings website.

Linear Slides


Linear Guide System - Two Piece
Linear Guide System - Two Piece

Using Frelon Gold plain bearing technology. Rail and carriage are made from 6063-T6 aluminium and come as a set.

Rails are ceramic coated to resist corrosion and repel weld spatter and contaminants. Smooth running. Dampens vibration. Guide has slots for T nuts or bolts. Two component system allows for easier installation than traditional rail systems.


A larger range of Linear Guide System - Two Piece might be available on the Bearing Shop Online site. There is also a good range of Linear Guide System - Two Piece on the Small Parts and Bearings website.

Linear Bearings with Housing




Clamping Rings


Rings - Retaining - PR Type Internal - For Linear Bearings
Rings - Retaining - PR Type Internal - For Linear Bearings

Push in retaining ring for use with closed type Super Smart, Super and Precision linear bearings. Installed in the housing bore at each end of the linear bearing.


There is also a good range of Rings - Retaining - PR Type Internal - For Linear Bearings on the Small Parts and Bearings website.

Linear Slides


Linear Slides - Utilitrak - CR - Carriage
Linear Slides - Utilitrak - CR - Carriage

Use with Utilitrak CR Channel. Stainless steel wheels with sealed bearings. Match by size.

Related Information:
Utilitrak CR Channel

A larger range of Linear Slides - Utilitrak - CR - Carriage might be available on the Bearing Shop Online site. There is also a good range of Linear Slides - Utilitrak - CR - Carriage on the Small Parts and Bearings website.

Bearings Special Purpose


Bearings - Spherical OD
Bearings - Spherical OD

Bearings with a spherical outside diameter.

Combined listing of spherical OD track rollers and bearings for Linear Guide systems.

Related Information:
Precision Shafting To Suit Bearings

A larger range of Bearings - Spherical OD might be available on the Bearing Shop Online site. There is also a good range of Bearings - Spherical OD on the Small Parts and Bearings website.

Linear Slides


Slides - Drawer - Front Disconnect - Friction - 19mm Ext
Slides - Drawer - Front Disconnect - Friction - 19mm Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted two member slide. Friction brake allows drawer to come to a slow stop. Front disconnects by pulling firmly on the drawer until it releases. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).


There is also a good range of Slides - Drawer - Front Disconnect - Friction - 19mm Ext on the Small Parts and Bearings website.

Slides - Drawer - Front Disconnect - Lever - Full Ext
Slides - Drawer - Front Disconnect - Lever - Full Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Front disconnects by lifting a lever lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).


There is also a good range of Slides - Drawer - Front Disconnect - Lever - Full Ext on the Small Parts and Bearings website.

Slides - Drawer - Front Disconnect - Friction - 19mm Ext - Undercarriage
Slides - Drawer - Front Disconnect - Friction - 19mm Ext - Undercarriage

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Undercarriage mounted two member slide. Friction brake allows drawer to come to a slow stop. Only one required per drawer. Requires 16 M4 or 8 Gauge Pan Head Screws (not included). Shipped with a bracket and two plastic tracks.


There is also a good range of Slides - Drawer - Front Disconnect - Friction - 19mm Ext - Undercarriage on the Small Parts and Bearings website.

Slides - Drawer - Front Disconnect - Latch Lever - Full Ext
Slides - Drawer - Front Disconnect - Latch Lever - Full Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Front disconnects by pressing a drawer latch lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).


There is also a good range of Slides - Drawer - Front Disconnect - Latch Lever - Full Ext on the Small Parts and Bearings website.

Slides - Drawer - Quick Disconnect - Medium Duty - Full Ext
Slides - Drawer - Quick Disconnect - Medium Duty - Full Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Positive stop slide with a quick disconnect.


There is also a good range of Slides - Drawer - Quick Disconnect - Medium Duty - Full Ext on the Small Parts and Bearings website.

Slides - Drawer - Stainless - Front Disconnect - Lever - 19mm Ext
Slides - Drawer - Stainless - Front Disconnect - Lever - 19mm Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted two member slide. Positive locking mechanism keeps drawer locked in the open position until actively released. Front disconnects by pressing a drawer latch lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).


There is also a good range of Slides - Drawer - Stainless - Front Disconnect - Lever - 19mm Ext on the Small Parts and Bearings website.

Linear Slides - Cross Roller Tables - Aluminium
Linear Slides - Cross Roller Tables - Aluminium

Also see combined categories:
All Crossed Roller Slide Tables

Crossed roller slide tables are factory assembled and ready to install. They use crossed roller bearings to provide very precise linear motion with low friction and high support stiffness for the load.

Applications include precision instruments, office and communications equipment, surface grinders, tool grinders, assembly fixtures and anywhere precise linear positioning is required. Precision ground v grooved ways and rollers provide high accuracy and load capacity. Withstands force in any direction from alternately crossed rollers at 45 deg angles. Straight line accuracy 0.0025mm per 25mm travel (0.0001 inch per inch). 0.0025mm position repeatability. Each table consists of a one piece base, a one piece table and a pair of linear bearings.


A larger range of Linear Slides - Cross Roller Tables - Aluminium might be available on the Bearing Shop Online site. There is also a good range of Linear Slides - Cross Roller Tables - Aluminium on the Small Parts and Bearings website.

Linear Slides - Cross Roller Tables - Steel
Linear Slides - Cross Roller Tables - Steel

Also see combined categories:
All Crossed Roller Slide Tables

Crossed roller slide tables are factory assembled and ready to install. They use crossed roller bearings to provide very precise linear motion with low friction and high support stiffness for the load.

Applications include precision instruments, office and communications equipment, surface grinders, tool grinders, assembly fixtures and anywhere precise linear positioning is required. Precision ground v grooved ways and rollers provide high accuracy and load capacity. Withstands force in any direction from alternately crossed rollers at 45 deg angles. Straight line accuracy 0.0025mm per 25mm travel (0.0001 inch per inch). 0.0025mm position repeatability. Each table consists of a one piece base, a one piece table and a pair of linear bearings.


A larger range of Linear Slides - Cross Roller Tables - Steel might be available on the Bearing Shop Online site. There is also a good range of Linear Slides - Cross Roller Tables - Steel on the Small Parts and Bearings website.

Shafting Aluminium


Shafting - Aluminium - Ceramic Coated
Shafting - Aluminium - Ceramic Coated

Also see combined categories:
All Shafting
All Aluminium Shafting

Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.

Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated.

Related Information:
Frelon Gold Linear Bearings

A larger range of Shafting - Aluminium - Ceramic Coated might be available on the Bearing Shop Online site. There is also a good range of Shafting - Aluminium - Ceramic Coated on the Small Parts and Bearings website.

Linear Slides


Slides - Drawer - Stainless - No Disconnect - Heavy Duty - 19mm Ext
Slides - Drawer - Stainless - No Disconnect - Heavy Duty - 19mm Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted two member slide. Positive stop slide that will not disconnect once installed. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).


There is also a good range of Slides - Drawer - Stainless - No Disconnect - Heavy Duty - 19mm Ext on the Small Parts and Bearings website.

Slides - Drawer - Stainless - No Disconnect - Heavy Duty - Full Ext
Slides - Drawer - Stainless - No Disconnect - Heavy Duty - Full Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Positive stop slide that will not disconnect once installed.


There is also a good range of Slides - Drawer - Stainless - No Disconnect - Heavy Duty - Full Ext on the Small Parts and Bearings website.

Slides - Drawer - Stainless - No Disconnect - Medium Duty - 19mm Ext
Slides - Drawer - Stainless - No Disconnect - Medium Duty - 19mm Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted two member slide. Positive stop slide that will not disconnect once installed. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).


There is also a good range of Slides - Drawer - Stainless - No Disconnect - Medium Duty - 19mm Ext on the Small Parts and Bearings website.

Slides - Drawer - Stainless - No Disconnect - Medium Duty - Full Ext
Slides - Drawer - Stainless - No Disconnect - Medium Duty - Full Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Positive stop slide that will not disconnect once installed.


There is also a good range of Slides - Drawer - Stainless - No Disconnect - Medium Duty - Full Ext on the Small Parts and Bearings website.

Linear Slides - Low Profile - Crossed Roller Table - Aluminium
Linear Slides - Low Profile - Crossed Roller Table - Aluminium

Also see combined categories:
All Crossed Roller Slide Tables

Crossed roller slide tables are factory assembled and ready to install. They use crossed roller bearings to provide very precise linear motion with low friction and high support stiffness for the load.

Applications include precision instruments, office and communications equipment, surface grinders, tool grinders, assembly fixtures and anywhere precise linear positioning is required. Precision ground v grooved ways and rollers provide high accuracy and load capacity. Withstands force in any direction from alternately crossed rollers at 45 deg angles. Straight line accuracy 0.0025mm per 25mm travel (0.0001 inch per inch). 0.0025mm position repeatability. Each table consists of a one piece base, a one piece table and a pair of linear bearings.


A larger range of Linear Slides - Low Profile - Crossed Roller Table - Aluminium might be available on the Bearing Shop Online site. There is also a good range of Linear Slides - Low Profile - Crossed Roller Table - Aluminium on the Small Parts and Bearings website.

Shafting Aluminium


Shafting - Aluminium - Ceramic Coated - Tapped
Shafting - Aluminium - Ceramic Coated - Tapped

Also see combined categories:
All Shafting
All Aluminium Shafting

Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.

Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated.

Related Information:
Frelon Gold Linear Bearings

A larger range of Shafting - Aluminium - Ceramic Coated - Tapped might be available on the Bearing Shop Online site. There is also a good range of Shafting - Aluminium - Ceramic Coated - Tapped on the Small Parts and Bearings website.

Linear Slides


Linear Slides - Low Profile - Crossed Roller Table - Stainless Steel
Linear Slides - Low Profile - Crossed Roller Table - Stainless Steel

Also see combined categories:
All Crossed Roller Slide Tables

Crossed roller slide tables are factory assembled and ready to install. They use crossed roller bearings to provide very precise linear motion with low friction and high support stiffness for the load.

Applications include precision instruments, office and communications equipment, surface grinders, tool grinders, assembly fixtures and anywhere precise linear positioning is required. Precision ground v grooved ways and rollers provide high accuracy and load capacity. Withstands force in any direction from alternately crossed rollers at 45 deg angles. Straight line accuracy 0.0025mm per 25mm travel (0.0001 inch per inch). 0.0025mm position repeatability. Each table consists of a one piece base, a one piece table and a pair of linear bearings.


A larger range of Linear Slides - Low Profile - Crossed Roller Table - Stainless Steel might be available on the Bearing Shop Online site. There is also a good range of Linear Slides - Low Profile - Crossed Roller Table - Stainless Steel on the Small Parts and Bearings website.

You may also like

Shafting Precision Ground


Shafting - Pre Drilled and Tapped - High Carbon Steel
Shafting - Pre Drilled and Tapped - High Carbon Steel

Also see combined categories:
All Shafting
All Steel Shafting

For use with rail supports and open linear bearings

Straightness: 0.1 mm / mtr.


A larger range of Shafting - Pre Drilled and Tapped - High Carbon Steel might be available on the Bearing Shop Online site. There is also a good range of Shafting - Pre Drilled and Tapped - High Carbon Steel on the Small Parts and Bearings website.

Shafting - Pre Drilled and Tapped - Stainless Steel Steel
Shafting - Pre Drilled and Tapped - Stainless Steel Steel

Also see combined categories:
All Shafting
All Stainless Shafting

For use with rail supports and open linear bearings


A larger range of Shafting - Pre Drilled and Tapped - Stainless Steel Steel might be available on the Bearing Shop Online site. There is also a good range of Shafting - Pre Drilled and Tapped - Stainless Steel Steel on the Small Parts and Bearings website.

Ball Transfers


Ball Transfer Units - Screw Stem - Steel - Precision
Ball Transfer Units - Screw Stem - Steel - Precision

Also see combined categories:
All Screw Fit Ball Transfers

Single ball bearings units for conveyor systems

Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.


A larger range of Ball Transfer Units - Screw Stem - Steel - Precision might be available on the Bearing Shop Online site. There is also a good range of Ball Transfer Units - Screw Stem - Steel - Precision on the Small Parts and Bearings website.

Linear Slides


Linear - Mini Rail - Self-Lubricating - Carriage
Linear - Mini Rail - Self-Lubricating - Carriage

Additional carriages for the Mini-Rail system. Match by rail width.

Low profile self-lubricating linear guide system with one piece carriage design. Excellent alternative to linear ball bearing systems. Precision series made from RC70 ceramic coated rail with self lubricating Frelon Gold. Dampens vibration and tolerates shock loads. Will not rust. No metal to metal contact. No balls or rolling elements to trap contamination, skid or damage rail. Operation is consistent, smooth and quiet. Maintenance free. Used in packaging machines, medical equipment, wash-down and harsh environments.

Related Information:
Matching Mini-Rail Rail

A larger range of Linear - Mini Rail - Self-Lubricating - Carriage might be available on the Bearing Shop Online site. There is also a good range of Linear - Mini Rail - Self-Lubricating - Carriage on the Small Parts and Bearings website.

Ball Transfers


Ball Transfer Units - Screw Stem - Brass and Aluminium
Ball Transfer Units - Screw Stem - Brass and Aluminium

Also see combined categories:
All Screw Fit Ball Transfers

Single ball bearings units for conveyor systems

Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.


A larger range of Ball Transfer Units - Screw Stem - Brass and Aluminium might be available on the Bearing Shop Online site. There is also a good range of Ball Transfer Units - Screw Stem - Brass and Aluminium on the Small Parts and Bearings website.

Linear Slides


Linear - Mini Rail - Self-Lubricating - Carriage and Rail
Linear - Mini Rail - Self-Lubricating - Carriage and Rail

Comes with one carriage. Spare carriages sold separately - match by rail width.

Low profile self-lubricating linear guide system with one piece carriage design. Excellent alternative to linear ball bearing systems. Precision series made from RC70 ceramic coated rail with self lubricating Frelon Gold. Dampens vibration and tolerates shock loads. Will not rust. No metal to metal contact. No balls or rolling elements to trap contamination, skid or damage rail. Operation is consistent, smooth and quiet. Maintenance free. Used in packaging machines, medical equipment, wash-down and harsh environments.

Related Information:
Matching Mini-Rail Carriage

A larger range of Linear - Mini Rail - Self-Lubricating - Carriage and Rail might be available on the Bearing Shop Online site. There is also a good range of Linear - Mini Rail - Self-Lubricating - Carriage and Rail on the Small Parts and Bearings website.

Shafting Precision Ground


Rail Supports - With Shaft - One Piece
Rail Supports - With Shaft - One Piece

Also see combined categories:
All Shaft Supports

One piece construction made from 6061-T6 Aluminium with ceramic coating to Mil-8625. Suitable for use with Frelon lined linear bearings.

Not suitable for linear ball bearings. Weld spatter, paints and other contaminants will not stick to the shaft. Vibration resistant and non-magnetic. Not suitable for harsh washdown environments.

Related Information:
Linear Bearing in Housing
Linear Bearings
Frelon Linear Bearings

A larger range of Rail Supports - With Shaft - One Piece might be available on the Bearing Shop Online site. There is also a good range of Rail Supports - With Shaft - One Piece on the Small Parts and Bearings website.

Linear Slides


Linear Track System - Crowned Roller
Linear Track System - Crowned Roller

Easy to use system is usually mounted on a vertical surface as a low cost linear motion solution.

Rails, rollers and end stops sold separately. Hardened crown roller allows for self-alignment with good strength and long life. Rails are unistrut typeand are black powder coated. End stops prevent over travel and come with a mounting bolt. End stops are not designed to support loads. Maximum bearing load is 130 kg. Maximum bearing speed is 45 mtrs per minute.


A larger range of Linear Track System - Crowned Roller might be available on the Bearing Shop Online site. There is also a good range of Linear Track System - Crowned Roller on the Small Parts and Bearings website.

Linear - Assemblies - Ball Slide - Precision
Linear - Assemblies - Ball Slide - Precision

These precision ball slides have a typical coefficient of friction of 0.003 and provide straight line accuracy of 0.0005mm per mm of travel.

At load capacity a life of 250 million mm of travel can be expected. The expected life at half load capacity is 2.5 billion mm. Factory preload adjustment prevents sideplay and backlash. Lightweight aluminium carriage and base with high load capacity. Four tapped and threaded carriage holes and counterbored base holes simplify installation and component mounting. Long life, self cleaning ball bearing needs no lubrication. Positional repeatability 0.005mm. Clear anodised finish.


A larger range of Linear - Assemblies - Ball Slide - Precision might be available on the Bearing Shop Online site. There is also a good range of Linear - Assemblies - Ball Slide - Precision on the Small Parts and Bearings website.

Linear Slide Assemblies - Plain - Low Profile - High Load
Linear Slide Assemblies - Plain - Low Profile - High Load

Also see combined categories:
All Linear Slide Assemblies

High capacity, square gib slides are ideal for precision machine tool applications.

The square gib design offers high load capacity and accuracy and withstands force in any direction. Gib is adjustable. Straight line accuracy 0.00254mm. Base is fabricated from A2 tool steel and hardened to Rc58-62. Saddle or riding portion of the slide is fabricated from low carbon steel and can be drilled, tapped and milled for mounting purposes. All slides feature Rulon bearing material for low friction. Stick-slip is virtually non existent as friction at startup and low speeds is virtually eliminated. No lubrication required. Rulon is practically inert to acids, bases and solvents making these slides a good choice for contaminated environments. Temp range minus 240 oC to +300 Deg C.


A larger range of Linear Slide Assemblies - Plain - Low Profile - High Load might be available on the Bearing Shop Online site. There is also a good range of Linear Slide Assemblies - Plain - Low Profile - High Load on the Small Parts and Bearings website.

Bearings Acetal


Bearings - Acetal - Disk Cleaning Applications
Bearings - Acetal - Disk Cleaning Applications

Also see combined categories:
All Plastic Single Row Bearings

Special acetal bearings for disk cleaning


A larger range of Bearings - Acetal - Disk Cleaning Applications might be available on the Bearing Shop Online site. There is also a good range of Bearings - Acetal - Disk Cleaning Applications on the Small Parts and Bearings website.

Bearings - Acetal - Double Row - with 316 Stainless Steel Balls
Bearings - Acetal - Double Row - with 316 Stainless Steel Balls

Also see combined categories:
All Plastic Ball Bearings

Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.

Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 oC to 100 oC Continuous.

Related Information:
Tolerances for acetal Bearings
Acetal Bearings with Glass Balls
Acetal Properties

A larger range of Bearings - Acetal - Double Row - with 316 Stainless Steel Balls might be available on the Bearing Shop Online site. There is also a good range of Bearings - Acetal - Double Row - with 316 Stainless Steel Balls on the Small Parts and Bearings website.

Bearings - Acetal - Double Row - with Glass Balls
Bearings - Acetal - Double Row - with Glass Balls

Also see combined categories:
All Plastic Ball Bearings

Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.

Races made from Acetal - Balls made from Ground Glass - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 oC to 100 oC Continuous.

Related Information:
Tolerances for acetal Bearings
Acetal Bearings with 316 Stainless Steel Balls
Acetal Properties

A larger range of Bearings - Acetal - Double Row - with Glass Balls might be available on the Bearing Shop Online site. There is also a good range of Bearings - Acetal - Double Row - with Glass Balls on the Small Parts and Bearings website.

Bearings - Acetal - MRI Table
Bearings - Acetal - MRI Table

Also see combined categories:
All Plastic Single Row Bearings

Special acetal bearings for MRI table wheels


A larger range of Bearings - Acetal - MRI Table might be available on the Bearing Shop Online site. There is also a good range of Bearings - Acetal - MRI Table on the Small Parts and Bearings website.

Bearings - Acetal - Single Row - with 302 Stainless Steel Balls
Bearings - Acetal - Single Row - with 302 Stainless Steel Balls

Also see combined categories:
All Plastic Ball Bearings
All Plastic Single Row Bearings

Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.

Races made from Acetal - Balls made from 302 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 oC to 100 oC Continuous.

Related Information:
Tolerances for acetal Bearings
Acetal Bearings with Glass Balls
Acetal Properties

A larger range of Bearings - Acetal - Single Row - with 302 Stainless Steel Balls might be available on the Bearing Shop Online site. There is also a good range of Bearings - Acetal - Single Row - with 302 Stainless Steel Balls on the Small Parts and Bearings website.

Bearings - Acetal - Single Row - with 316 Stainless Steel Balls
Bearings - Acetal - Single Row - with 316 Stainless Steel Balls

Also see combined categories:
All Plastic Ball Bearings
All Plastic Single Row Bearings

Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.

Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 oC to 100 oC Continuous.

Related Information:
Tolerances for acetal Bearings
Acetal Bearings with Glass Balls
Acetal Properties

A larger range of Bearings - Acetal - Single Row - with 316 Stainless Steel Balls might be available on the Bearing Shop Online site. There is also a good range of Bearings - Acetal - Single Row - with 316 Stainless Steel Balls on the Small Parts and Bearings website.

Bearings - Acetal - Single Row - with Glass Balls
Bearings - Acetal - Single Row - with Glass Balls

Also see combined categories:
All Plastic Ball Bearings
All Plastic Single Row Bearings

Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.

Races made from Acetal - Balls made from Ground Glass - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 oC to 100 oC Continuous.

Related Information:
Tolerances for acetal Bearings
Acetal Bearings with 316 Stainless Steel Balls
Acetal Properties

A larger range of Bearings - Acetal - Single Row - with Glass Balls might be available on the Bearing Shop Online site. There is also a good range of Bearings - Acetal - Single Row - with Glass Balls on the Small Parts and Bearings website.

Bearings - Acetal - Special Purpose
Bearings - Acetal - Special Purpose

Also see combined categories:
All Plastic Single Row Bearings

Special acetal bearings for Bicycle Chain Derailer and special effects lighting systems


A larger range of Bearings - Acetal - Special Purpose might be available on the Bearing Shop Online site. There is also a good range of Bearings - Acetal - Special Purpose on the Small Parts and Bearings website.

Bearings - Acetal - Special Types
Bearings - Acetal - Special Types

Also see combined categories:
All Plastic Ball Bearings

Light duty acetal bearings used for drawer runners, light duty tracks, garage doors and more.

See descriptions for special features. Not all items are listed in this category. Please contact us if you have a similar type bearing with different dimensions.


A larger range of Bearings - Acetal - Special Types might be available on the Bearing Shop Online site. There is also a good range of Bearings - Acetal - Special Types on the Small Parts and Bearings website.

Bearings for Pool Equipment
Bearings for Pool Equipment

Acetal bearings for spa jets and pool vacuum wheels

Water Lubrication.

Related Information:
Tolerances for acetal Bearings
Acetal Bearings with Glass Balls
Acetal Properties

A larger range of Bearings for Pool Equipment might be available on the Bearing Shop Online site. There is also a good range of Bearings for Pool Equipment on the Small Parts and Bearings website.

Bearings - Polypropylene - Special Types
Bearings - Polypropylene - Special Types

Also see combined categories:
All Plastic Ball Bearings

Polypropylene is for special chemical compatibility usages. Please refer to a compatibility chart.

See descriptions for special features. Not all items are listed in this category. Please contact us if you have a similar type bearing with different dimensions.


A larger range of Bearings - Polypropylene - Special Types might be available on the Bearing Shop Online site. There is also a good range of Bearings - Polypropylene - Special Types on the Small Parts and Bearings website.

Bearings 316 Stainless


Bearings - Ball - 316 Stainless Steel - Double Row - Open
Bearings - Ball - 316 Stainless Steel - Double Row - Open

Also see combined categories:
All 300 Grade Stainless Bearings

Marine, food and medical grade Stainless Steel - Non Hardenable. Open, easier to lubricate. Water lubrication is ok.

Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance.

Related Information:
Tolerances
Precision Shafting To Suit Bearings

A larger range of Bearings - Ball - 316 Stainless Steel - Double Row - Open might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - 316 Stainless Steel - Double Row - Open on the Small Parts and Bearings website.

Bearings - Ball - 316 Stainless Steel - Single Row - Open
Bearings - Ball - 316 Stainless Steel - Single Row - Open

Also see combined categories:
All 300 Grade Stainless Bearings

Marine, food and medical grade Stainless Steel - Non Hardenable. Open, easier to lubricate. Water lubrication is ok.

Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance.

Related Information:
Tolerances
Precision Shafting To Suit Bearings

A larger range of Bearings - Ball - 316 Stainless Steel - Single Row - Open might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - 316 Stainless Steel - Single Row - Open on the Small Parts and Bearings website.

Bearings - Ball - 316 Stainless Steel - Single Row - Sealed
Bearings - Ball - 316 Stainless Steel - Single Row - Sealed

Also see combined categories:
All 300 Grade Stainless Bearings

Marine, food and medical grade Stainless Steel - Non Hardenable. Polyethylene plastic seals.

Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races, greased. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.

Related Information:
Tolerances
Precision Shafting To Suit Bearings

A larger range of Bearings - Ball - 316 Stainless Steel - Single Row - Sealed might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - 316 Stainless Steel - Single Row - Sealed on the Small Parts and Bearings website.

Bearings - Ball - 316 Stainless Steel - Single Row - Shielded
Bearings - Ball - 316 Stainless Steel - Single Row - Shielded

Also see combined categories:
All 300 Grade Stainless Bearings

Marine, food and medical grade Stainless Steel - Non Hardenable. 316 stainless steel shields.

Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Stainless steel 316 cage, grade 200 type 316 stainless balls, 316 stainless races, 316 stainless steel shields. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.

Related Information:
Tolerances
Precision Shafting To Suit Bearings

A larger range of Bearings - Ball - 316 Stainless Steel - Single Row - Shielded might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - 316 Stainless Steel - Single Row - Shielded on the Small Parts and Bearings website.

Bearings Angular Contact


Bearings - Ball - Angular Contact - 440C Stainless
Bearings - Ball - Angular Contact - 440C Stainless

Also see combined categories:
All Angular Contact Bearings

Including miniature sizes down to 8mm from stock and even smaller available.

Single row angular contact ball bearings.

Related Information:
Precision Shafting To Suit Bearings

A larger range of Bearings - Ball - Angular Contact - 440C Stainless might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - Angular Contact - 440C Stainless on the Small Parts and Bearings website.

Bearings - Ball - Angular Contact - Chrome Steel
Bearings - Ball - Angular Contact - Chrome Steel

Also see combined categories:
All Angular Contact Bearings

Including miniature sizes down to 8mm from stock and even smaller available.

Single row angular contact ball bearings.

Related Information:
Precision Shafting To Suit Bearings

A larger range of Bearings - Ball - Angular Contact - Chrome Steel might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - Angular Contact - Chrome Steel on the Small Parts and Bearings website.

Bearings - Ball - Angular Contact - Flanged - 440C Stainless
Bearings - Ball - Angular Contact - Flanged - 440C Stainless

Also see combined categories:
All Angular Contact Bearings

Single row angular contact ball bearings with flanges.

Related Information:
Precision Shafting To Suit Bearings

A larger range of Bearings - Ball - Angular Contact - Flanged - 440C Stainless might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - Angular Contact - Flanged - 440C Stainless on the Small Parts and Bearings website.

Bearings Ceramic


Bearings - Ball - Ceramic Hybrid
Bearings - Ball - Ceramic Hybrid

Also see combined categories:
All Radial Ball Bearings

Steel Races with Si3N4 Ceramic Balls

Bearings with steel races and ceramic balls. For standard bearings, the balls are usually one of the first components to show wear. Ceramic balls are harder than steel and do not wear as easily. Items with high speed cages have the suffixes T9H, TNH, TW or KC.

Related Information:
Tolerances
Precision Shafting To Suit Bearings

A larger range of Bearings - Ball - Ceramic Hybrid might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - Ceramic Hybrid on the Small Parts and Bearings website.

Bearings - Ceramic Si3N4 - Angular Contact
Bearings - Ceramic Si3N4 - Angular Contact

Also see combined categories:
All Angular Contact Bearings
All Full Ceramic Bearings

Excellent performance in electrical and magnetism sensitive applications. Higher speed than Zr02. Full ceramic silicon nitride.

Excellent performance in electrical and magnetism sensitive applications, including cryopumps, medical applications, semiconductors, turbine flow meters, food processing, robotics and optics. Wear and corrosion resistance. Lubrication and maintenance free. 3.2g/cubic cm density. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. Si3N4 (GSN-201) standard material for balls, cage and rings. HRC80 Hardness. High and low- temperature application. Up to 250 oC with PTFE Cage and 130 Deg C with Nylon Cage.

Related Information:
See also Zirconia Ceramic Bearings

A larger range of Bearings - Ceramic Si3N4 - Angular Contact might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ceramic Si3N4 - Angular Contact on the Small Parts and Bearings website.

Bearings - Ceramic Si3N4 - Radial
Bearings - Ceramic Si3N4 - Radial

Also see combined categories:
All Radial Ball Bearings
All Full Ceramic Bearings

Excellent performance in electrical and magnetism sensitive applications. Higher speed than Zr02. Full ceramic silicon nitride.

Excellent performance in electrical and magnetism sensitive applications, including cryopumps, medical applications, semiconductors, turbine flow meters, food processing, robotics and optics. Wear and corrosion resistance. Lubrication and maintenance free. 3.2g/cubic cm density. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. Si3N4 (GSN-201) standard material for balls, cage and rings. HRC80 Hardness. High and low- temperature application. Up to 250 oC with PTFE Cage and 130 Deg C with Nylon Cage.

Related Information:
See also Zirconia Ceramic Bearings

A larger range of Bearings - Ceramic Si3N4 - Radial might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ceramic Si3N4 - Radial on the Small Parts and Bearings website.

Bearings - Ceramic ZrO2 - Radial
Bearings - Ceramic ZrO2 - Radial

Also see combined categories:
All Radial Ball Bearings
All Full Ceramic Bearings

Excellent performance in electrical and magnetism sensitive applications. Not for High Speed. Full ceramic zirconia.

Excellent performance in electrical and magnetism sensitive applications, including cryopumps, medical applications, semiconductors, turbine flow meters, food processing, robotics and optics. Wear and corrosion resistance. Lubrication and maintenance free. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. ZrO2 standard material for balls, cage and rings. Si3N4 available to special order. High and low- temperature application. Up to 250 oC with PTFE Cage and 130 Deg C with Nylon Cage.

Related Information:
See also Silicon Nitride Ceramic Bearings

A larger range of Bearings - Ceramic ZrO2 - Radial might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ceramic ZrO2 - Radial on the Small Parts and Bearings website.

Bearings - Ceramic ZrO2 - Self Aligning - Double Row
Bearings - Ceramic ZrO2 - Self Aligning - Double Row

Also see combined categories:
All Radial Ball Bearings
All Full Ceramic Bearings

Excellent performance in electrical and magnetism sensitive applications. Not for High Speed. Full ceramic zirconia.

Excellent performance in electrical and magnetism sensitive applications, including cryopumps, medical applications, semiconductors, turbine flow meters, food processing, robotics and optics. Wear and corrosion resistance. Lubrication and maintenance free. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. ZrO2 standard material for balls, cage and rings. Si3N4 available to special order. High and low- temperature application. Up to 250 oC with PTFE Cage and 130 Deg C with Nylon Cage.

Related Information:
See also Silicon Nitride Ceramic Bearings
See other zirconia ceramic bearings

A larger range of Bearings - Ceramic ZrO2 - Self Aligning - Double Row might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ceramic ZrO2 - Self Aligning - Double Row on the Small Parts and Bearings website.

Bearings Conveyor


Bearings - Conveyor - Hex Bore - Plastic - Double Row
Bearings - Conveyor - Hex Bore - Plastic - Double Row

Also see combined categories:
All Conveyor Bearings

Plastic hex bore conveyor bearings with 316 stainless balls

Loads and Speeds are for reference only. Testing recommended.


A larger range of Bearings - Conveyor - Hex Bore - Plastic - Double Row might be available on the Bearing Shop Online site. There is also a good range of Bearings - Conveyor - Hex Bore - Plastic - Double Row on the Small Parts and Bearings website.

Bearings - Conveyor - Hex Bore - Plastic - Single Row
Bearings - Conveyor - Hex Bore - Plastic - Single Row

Also see combined categories:
All Conveyor Bearings

Plastic hex bore conveyor bearings with 316 stainless balls

Loads and Speeds are for reference only. Testing recommended.


A larger range of Bearings - Conveyor - Hex Bore - Plastic - Single Row might be available on the Bearing Shop Online site. There is also a good range of Bearings - Conveyor - Hex Bore - Plastic - Single Row on the Small Parts and Bearings website.

Bearings - Conveyor - Hex Bore - Stainless Steel - Double Row
Bearings - Conveyor - Hex Bore - Stainless Steel - Double Row

Also see combined categories:
All Conveyor Bearings

316 stainless conveyor bearings with plastic cage and plastic hex insert

Loads and Speeds are for reference only. Testing recommended.


A larger range of Bearings - Conveyor - Hex Bore - Stainless Steel - Double Row might be available on the Bearing Shop Online site. There is also a good range of Bearings - Conveyor - Hex Bore - Stainless Steel - Double Row on the Small Parts and Bearings website.

Bearings - Conveyor - Hex Bore - Stainless Steel - Single Row
Bearings - Conveyor - Hex Bore - Stainless Steel - Single Row

Also see combined categories:
All Conveyor Bearings

316 stainless conveyor bearings with plastic cage and plastic hex insert

Loads and Speeds are for reference only. Testing recommended.


A larger range of Bearings - Conveyor - Hex Bore - Stainless Steel - Single Row might be available on the Bearing Shop Online site. There is also a good range of Bearings - Conveyor - Hex Bore - Stainless Steel - Single Row on the Small Parts and Bearings website.

Bearings Double Row Ball


Bearings - Ball - Double Row - Angular Contact - Chrome Steel
Bearings - Ball - Double Row - Angular Contact - Chrome Steel

Also see combined categories:
All Double Row Ball Bearings

Double Row Ball Bearings - Angular Contact.

Related Information:
Precision Shafting To Suit Bearings

A larger range of Bearings - Ball - Double Row - Angular Contact - Chrome Steel might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - Double Row - Angular Contact - Chrome Steel on the Small Parts and Bearings website.

Bearings - Ball - Double Row - Angular Contact - Stainless Steel
Bearings - Ball - Double Row - Angular Contact - Stainless Steel

Also see combined categories:
All Double Row Ball Bearings

Double Row Ball Bearings - Angular Contact.

Related Information:
Precision Shafting To Suit Bearings

A larger range of Bearings - Ball - Double Row - Angular Contact - Stainless Steel might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - Double Row - Angular Contact - Stainless Steel on the Small Parts and Bearings website.

Bearings - Ball - Double Row - Radial - Chrome Steel
Bearings - Ball - Double Row - Radial - Chrome Steel

Also see combined categories:
All Double Row Ball Bearings

Related Information:
Precision Shafting To Suit Bearings

A larger range of Bearings - Ball - Double Row - Radial - Chrome Steel might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - Double Row - Radial - Chrome Steel on the Small Parts and Bearings website.

Bearings - Ball - Double Row - Self Aligning - Parallel Bore
Bearings - Ball - Double Row - Self Aligning - Parallel Bore

Also see combined categories:
All Double Row Ball Bearings
All Self Aligning Ball Bearings

Related Information:
Precision Shafting To Suit Bearings

A larger range of Bearings - Ball - Double Row - Self Aligning - Parallel Bore might be available on the Bearing Shop Online site. There is also a good range of Bearings - Ball - Double Row - Self Aligning - Parallel Bore on the Small Parts and Bearings website.

Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Miniature Bearings Australia offers 122785 products in 2708 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Miniature Bearings Australia offers 122785 products in 2708 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.