Miniature Bearings Australia Pty Ltd

BALLS


Category Matches

Balls Rubber


Balls - Rubber - Santoprene 40D
Balls - Rubber - Santoprene 40D

Also see combined categories:
All Rubber Balls
All Non Metallic Balls

A high performance thermoplastic created by cross linking EPDM rubber with Polypropylene. As an elastomer plastic it is flexible, light weight, and has very good abrasion resistance. It also has good resistance to many acids, bases and aqueous solutions.

It holds up well in both extreme hot and cold environments which can make it preferred over rubber. Common uses include; grips, knobs, handles, gaskets, and ball check valves. Specific Gravity .95 g/cc. Hardness, Shore 40D. Tensile Strength 3000 psi. Melting Point 410 F. Rohs Compliant. Not FDA compliant. This grade is slightly harder than the 87A grade. Colour usually red but some sizes are beige.

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Rubber - Santoprene 40D on the Small Parts and Bearings website.


Balls - Rubber - Santoprene 87A
Balls - Rubber - Santoprene 87A

Also see combined categories:
All Rubber Balls
All Non Metallic Balls

A high performance thermoplastic created by cross linking EPDM rubber with Polypropylene. As an elastomer plastic it is flexible, light weight, and has very good abrasion resistance. It also has good resistance to many acids, bases and aqueous solutions.

It holds up well in both extreme hot and cold environments which can make it preferred over rubber. Common uses include; grips, knobs, handles, gaskets, and ball check valves. Specific Gravity .96 g/cc. Hardness, Shore 87A. Tensile Strength 2550 psi. Melting Point 400 F. Rohs Compliant and FDA compliant. This grade is slightly softer than the 40D grade. Colour Beige.

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Rubber - Santoprene 87A on the Small Parts and Bearings website.


Balls Ceramic


Balls - Ceramic - Ruby - Synthetic
Balls - Ceramic - Ruby - Synthetic

Also see combined categories:
All Ceramic Balls
All Non Metallic Balls

Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.

Tolerances available on request. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Specific Gravity: 3.98.

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Ceramic - Ruby - Synthetic on the Small Parts and Bearings website.


Balls - Ceramic - Sapphire - Synthetic
Balls - Ceramic - Sapphire - Synthetic

Also see combined categories:
All Ceramic Balls
All Non Metallic Balls

Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.

Tolerances available on request. Specific Gravity: 3.98. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Transparent (refractive index 1.76).

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Ceramic - Sapphire - Synthetic on the Small Parts and Bearings website.


Balls - Ceramic - Silicon Nitride
Balls - Ceramic - Silicon Nitride

Also see combined categories:
All Ceramic Balls
All Non Metallic Balls

Outstanding wear resistance. Good thermal and chemical resistance.

High hardness. High strength over a wide temperature range. High fracture toughness. Outstanding wear resistance. Good thermal and chemical resistance.

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Ceramic - Silicon Nitride on the Small Parts and Bearings website.


Balls - Ceramic - Zirconia
Balls - Ceramic - Zirconia

Also see combined categories:
All Ceramic Balls
All Non Metallic Balls

Outstanding wear resistance. Excellent thermal and chemical resistance.

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Ceramic - Zirconia on the Small Parts and Bearings website.


Balls Plastic


Balls - Plastic - Acetal
Balls - Plastic - Acetal

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

High intensity strength, rigidity, outstanding resistance to abrasion and most solvents.

Tolerances available on request. Acetal Copolymer. High intensity strength, rigidity, outstanding resistance to abrasion and most solvents. Opaque White. Specific Gravity: 1.4.

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Plastic - Acetal on the Small Parts and Bearings website.


Balls - Plastic - Acrylic
Balls - Plastic - Acrylic

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

Resistance to weather and sunlight. Good abrasion resistance.

Diametrical tolerances typically +/- 0.08 or 0.13 mm depending on size. Acrylic (Methyl Methacrylate). Resistance to weather and sunlight. Good abrasion resistance. Water clear transparent. Polished. Ground and Polished.

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Plastic - Acrylic on the Small Parts and Bearings website.


Balls - Plastic - Bored
Balls - Plastic - Bored

Also see combined categories:
All Plastic Balls - Bored

Bored acetal balls as used in plastic rod ends.

Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight.

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Plastic - Bored on the Small Parts and Bearings website.


Balls - Plastic - Nylon
Balls - Plastic - Nylon

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

Resists alkalies, weak acids and most organic solvents.

Tolerances available on request. Nylon (Polyamide 6/6). Resists alkalies, weak acids and most organic solvents. Low water absorption. Unpolished. Specific Gravity: 1.14.

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Plastic - Nylon on the Small Parts and Bearings website.


Balls - Plastic - Polypropylene
Balls - Plastic - Polypropylene

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

Excellent for liquid level float applications.

Tolerance and spherecity: up to and including 25.4mm diameter = +/-0.0508mm, over 25.4mm diameter +/-0.0762mm. Very resistant to most acids and alkalies. Excellent for liquid level float applications. Unpolished. Specific Gravity: 0.91.

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Plastic - Polypropylene on the Small Parts and Bearings website.


Balls - Plastic - PTFE
Balls - Plastic -  PTFE

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

No water absorption. Temperatures up to 288 Deg C.

Tolerances available on request. Not affected by any known acids or alkalies. No water absorption. Temperatures up to 288 oC. Unpolished. Specific Gravity: 2.3.

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Plastic - PTFE on the Small Parts and Bearings website.


Balls - Plastic - PVC
Balls - Plastic -  PVC

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

Polyvinyl chloride. PVC is a chemically stable material, which shows little change in molecular structure, and also exhibits little change in its mechanical strength.

Polyvinyl chloride is a widely used and inexpensive thermoplastic polymer. It is easily worked or machined and has good chemical and biological resistance. It is relatively hard and can be polished to a shine. Polyvinyl chloride is a widely used and inexpensive thermoplastic polymer. Heat Deflection Temperature 176 F / 80 C. Rockwell Hardness 115. Zero water absorption in 24 hours.

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Plastic - PVC on the Small Parts and Bearings website.


Balls - Plastic - Torlon
Balls - Plastic - Torlon

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

TorlonTM 4301 Bearing Grade Balls. Grade 1.

Polyamide-imide (TorlonTM) Balls. Rockwell Hardness (Method A): E86 or M109-119. Specific Gravity: 1.38. Colour: Brown Opaque.

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Plastic - Torlon on the Small Parts and Bearings website.


Ball Joints


Joints - Ball Positioner
Joints - Ball Positioner

For holding parts at an angle up to 45 degrees

Pivots 45 Deg from horizontal in every direction. Tightens at any position by rotating the collar. Has a tapped hole at the top and a male thread at the bottom for securing.


There is also a good range of Joints - Ball Positioner on the Small Parts and Bearings website.


Balls Metallic


Balls - Chrome Steel
Balls - Chrome Steel

Also see combined categories:
All Metallic Balls

Hardness: Rockwell C: 60-70.

Tolerances available on request. SAE 52100 Chrome Steel. Hardness: Rockwell C: 60-70. Specific Gravity: 7.833.

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Chrome Steel on the Small Parts and Bearings website.


Balls - Phosphor Bronze
Balls - Phosphor Bronze

Also see combined categories:
All Metallic Balls

Specific Gravity 8.4

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Phosphor Bronze on the Small Parts and Bearings website.


Balls - Stainless Steel - 304 Grade
Balls - Stainless Steel - 304 Grade

Also see combined categories:
All Metallic Balls

A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.

Tolerances available on request. Grade 100. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000 oC.

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Stainless Steel - 304 Grade on the Small Parts and Bearings website.


Balls - Stainless Steel - 316 Grade
Balls - Stainless Steel - 316 Grade

Also see combined categories:
All Metallic Balls

A4 Grade. Very low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.

Tolerances available on request. Grade 100. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000 oC.

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Stainless Steel - 316 Grade on the Small Parts and Bearings website.


Balls - Stainless Steel - 316L Grade
Balls - Stainless Steel - 316L Grade

Also see combined categories:
All Metallic Balls

Easier to machine than standard 316 grade.

316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Stainless Steel - 316L Grade on the Small Parts and Bearings website.


Balls - Stainless Steel - 440C Grade
Balls - Stainless Steel - 440C Grade

Also see combined categories:
All Metallic Balls

Hardness: Rockwell C: 55-60.

Tolerances available on request. AISI440C Stainless Steel.

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Stainless Steel - 440C Grade on the Small Parts and Bearings website.


Balls - Steel - Bored
Balls - Steel - Bored

Also see combined categories:
All Metallic Balls - Bored

Bored steel balls as used in steel rod ends.

Hardness: 58-64 Rc. Material: SUJ-2.

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Steel - Bored on the Small Parts and Bearings website.


Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI
Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI

Also see combined categories:
All Metallic Balls

Implant Grade can be used for Jewellery and Body Piercing. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.

Precision Grade: 200. Plain. Composition Percentage: Al 5.5-6.5, V 3.5-4.5, N 0.03, C 0.08, H 0.013, Fe 0.25, O 0.13, Ti Balance. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI on the Small Parts and Bearings website.


Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI - Threaded
Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI - Threaded

Also see combined categories:
All Threaded Metallic Balls

Implant Grade can be used for Jewellery and Body Piercing. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.

Precision Grade: 200. Plain. Composition Percentage: Al 5.5-6.5, V 3.5-4.5, N 0.03, C 0.08, H 0.013, Fe 0.25, O 0.13, Ti Balance. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent. Threaded either 1-72 UNF or M1.2.

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI - Threaded on the Small Parts and Bearings website.


Balls - Tungsten Carbide
Balls - Tungsten Carbide

Also see combined categories:
All Metallic Balls

Extreme hardness and wear resistance.

Tolerances available on request. Precision Grade: Grade 25. Hardness: Rockwell A: 91.5 (Approx 77 Rockwell C). Extreme hardness and wear resistance. Specific Gravity: 14.95.

Related Information:
AFBMA Ball Grades
Other Types of Balls

There is also a good range of Balls - Tungsten Carbide on the Small Parts and Bearings website.


Ball Transfers


Ball Transfer Units - Base Mount - Heavy Duty - Steel
Ball Transfer Units - Base Mount  - Heavy Duty - Steel

Also see combined categories:
All Base Mount Ball Transfers

Single ball bearings units for conveyor systems


There is also a good range of Ball Transfer Units - Base Mount - Heavy Duty - Steel on the Small Parts and Bearings website.


Ball Transfer Units - Base Mount - Standard - Steel
Ball Transfer Units - Base Mount - Standard - Steel

Also see combined categories:
All Base Mount Ball Transfers

Single ball bearings units for conveyor systems


There is also a good range of Ball Transfer Units - Base Mount - Standard - Steel on the Small Parts and Bearings website.


Ball Transfer Units - Dismantlable - Heavy Duty - Steel
Ball Transfer Units - Dismantlable  - Heavy Duty - Steel

Also see combined categories:
All Push Fit Ball Transfers

Single ball bearings units for conveyor systems


There is also a good range of Ball Transfer Units - Dismantlable - Heavy Duty - Steel on the Small Parts and Bearings website.


Ball Transfer Units - Flange Mount - Heavy Duty - Pressed Steel
Ball Transfer Units - Flange Mount - Heavy Duty - Pressed Steel

Also see combined categories:
All Flange Mount Ball Transfers

Single ball bearings units for conveyor systems


There is also a good range of Ball Transfer Units - Flange Mount - Heavy Duty - Pressed Steel on the Small Parts and Bearings website.


Ball Transfer Units - Flange Mount - Heavy Duty - Stainless Steel
Ball Transfer Units - Flange Mount - Heavy Duty - Stainless Steel

Also see combined categories:
All Flange Mount Ball Transfers

Single ball bearings units for conveyor systems


There is also a good range of Ball Transfer Units - Flange Mount - Heavy Duty - Stainless Steel on the Small Parts and Bearings website.


Ball Transfer Units - Flange Mount - Heavy Duty - Zinc Plated
Ball Transfer Units - Flange Mount - Heavy Duty - Zinc Plated

Also see combined categories:
All Flange Mount Ball Transfers

Single ball bearings units for conveyor systems


There is also a good range of Ball Transfer Units - Flange Mount - Heavy Duty - Zinc Plated on the Small Parts and Bearings website.


Ball Transfer Units - Flange Mount - Standard - Stainless - Deep
Ball Transfer Units - Flange Mount - Standard - Stainless - Deep

Also see combined categories:
All Flange Mount Ball Transfers

Single ball bearings units for conveyor systems


There is also a good range of Ball Transfer Units - Flange Mount - Standard - Stainless - Deep on the Small Parts and Bearings website.


Ball Transfer Units - Flange Mount - Standard - Stainless - Slim
Ball Transfer Units - Flange Mount - Standard - Stainless - Slim

Also see combined categories:
All Flange Mount Ball Transfers

Single ball bearings units for conveyor systems


There is also a good range of Ball Transfer Units - Flange Mount - Standard - Stainless - Slim on the Small Parts and Bearings website.


Ball Transfer Units - Flange Mount - Standard - Steel - Slim
Ball Transfer Units - Flange Mount - Standard - Steel - Slim

Also see combined categories:
All Flange Mount Ball Transfers

Single ball bearings units for conveyor systems


There is also a good range of Ball Transfer Units - Flange Mount - Standard - Steel - Slim on the Small Parts and Bearings website.


Ball Transfer Units - Screw Stem - Brass and Aluminium
Ball Transfer Units - Screw Stem - Brass and Aluminium

Also see combined categories:
All Screw Fit Ball Transfers

Single ball bearings units for conveyor systems

Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.


There is also a good range of Ball Transfer Units - Screw Stem - Brass and Aluminium on the Small Parts and Bearings website.


Ball Transfer Units - Screw Stem - Steel - Precision
Ball Transfer Units - Screw Stem - Steel - Precision

Also see combined categories:
All Screw Fit Ball Transfers

Single ball bearings units for conveyor systems

Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.


There is also a good range of Ball Transfer Units - Screw Stem - Steel - Precision on the Small Parts and Bearings website.


Ball Transfer Units - Spring Loaded - Flanged - Zinc Plated
Ball Transfer Units - Spring Loaded - Flanged - Zinc Plated

Single ball bearings units for conveyor systems

Case: Zinc plated Mild Steel. Ball: Carbon Steel 60-66 HRC. Applications: - Guillotines - Presses - Moulding machines - Base of machines for easy handling - Press brakes - Shock loading.


There is also a good range of Ball Transfer Units - Spring Loaded - Flanged - Zinc Plated on the Small Parts and Bearings website.


Ball Transfer Units - Spring Loaded - Unflanged - Zinc Plated
Ball Transfer Units - Spring Loaded - Unflanged - Zinc Plated

Also see combined categories:
All Push Fit Ball Transfers

Single ball bearings units for conveyor systems

Case: Zinc plated Mild Steel. Ball: Carbon Steel 60-66 HRC. Applications: - Guillotines - Presses - Moulding machines - Base of machines for easy handling - Press brakes - Shock loading.


There is also a good range of Ball Transfer Units - Spring Loaded - Unflanged - Zinc Plated on the Small Parts and Bearings website.


Ball Parallels


Parallels - Ball
Parallels - Ball

Used for handling large work in drill presses or band saw machines.

Placed between work and machine so work can be easily moved. Black Oxide finish with 9.525mm hardened steel balls. Balls are exposed both sides of sheet.


There is also a good range of Parallels - Ball on the Small Parts and Bearings website.


Ball Splines Linear


Linear Ball Splines - Bearings - Unflanged
Linear Ball Splines - Bearings - Unflanged

Also see combined categories:
All Linear Ball Splines

Use with Linear Ball Spline Shaft.

Related Information:
Shaft To Suit

There is also a good range of Linear Ball Splines - Bearings - Unflanged on the Small Parts and Bearings website.


Ball Screws Rolled


Ballscrew - Thomson Saginaw
Ballscrew - Thomson Saginaw

Also see combined categories:
All Ball Screws

Offer 90% efficiency converting rotary to linear motion with low coefficient of friction. Match all components within the Thomson Saginaw range only.

When replacing screws, hydraulics or pneumatics, they allow the use of smaller, less expensive drive motors and reduce the need for auxiliary equipment. Offer dependable accuracy and repeatability, Made off high quality alloy steel, hardened to Rockwell 56-60C.


There is also a good range of Ballscrew - Thomson Saginaw on the Small Parts and Bearings website.


Ball Screw Accessories


Ballscrew - Thomson Saginaw - Accessories
Ballscrew - Thomson Saginaw - Accessories

Also see combined categories:
All Ball Screws

Wiper Kits and Flanges for Ball Nuts. Match all components within the Thomson Saginaw range only.


There is also a good range of Ballscrew - Thomson Saginaw - Accessories on the Small Parts and Bearings website.


Ballscrew - Thomson Saginaw - Nut
Ballscrew - Thomson Saginaw - Nut

Also see combined categories:
All Ball Screws

Ball Nuts to Suit Thomson Saginaw ball screws. Match all components within the Thomson Saginaw range only.

All Right hand thread only.


There is also a good range of Ballscrew - Thomson Saginaw - Nut on the Small Parts and Bearings website.


Ball Screws 16mm SDP


Ballscrew - 16mm Nuts - Pillow Block
Ballscrew - 16mm Nuts - Pillow Block

Also see combined categories:
All Ball Screws

Includes ball nut. Match all components within the 16mm range only.

Antibacklash. Repeatability 0.01mm, accuracy 0.1mm/300mm when used with our 16mm screws. Hardened ground and polished Cf53 steel to HRC62 +/-2. Balls hardened HRC63 +/- 2.


There is also a good range of Ballscrew - 16mm Nuts - Pillow Block on the Small Parts and Bearings website.


Ball Screws Ground


Ballscrew - Ground - Dia 4mm - Lead 1mm
Ballscrew - Ground - Dia 4mm - Lead 1mm

Also see combined categories:
All Ball Screws

Not for sale outside of Australia and New Zealand


There is also a good range of Ballscrew - Ground - Dia 4mm - Lead 1mm on the Small Parts and Bearings website.


Ball Screws Nook Series


Ballscrew - Nook Series - Flanges
Ballscrew - Nook Series - Flanges

Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish.


There is also a good range of Ballscrew - Nook Series - Flanges on the Small Parts and Bearings website.


Ballscrew - Nook Series - Right Hand
Ballscrew - Nook Series - Right Hand

Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

High quality alloy steel, induction hardened to RC 56-60. Protective black oxide finish. Lead accurate by at least 0.00083mm per mm.


There is also a good range of Ballscrew - Nook Series - Right Hand on the Small Parts and Bearings website.


Ball Screws Ground


Ballscrew - Ground - Bi-Directional - Dia 8mm - Lead 1mm
Ballscrew - Ground - Bi-Directional - Dia 8mm - Lead 1mm

Also see combined categories:
All Ball Screws

Not for sale outside of Australia and New Zealand


There is also a good range of Ballscrew - Ground - Bi-Directional - Dia 8mm - Lead 1mm on the Small Parts and Bearings website.


Ball Screw Accessories


Mounts - Universal - For Acme Thread and Ballscrews
Mounts - Universal - For Acme Thread and Ballscrews

Use grade 8 hex socket head cap screws for mounting.


There is also a good range of Mounts - Universal - For Acme Thread and Ballscrews on the Small Parts and Bearings website.


Ball Screws Nook Series


Ballscrew - Nook Series - Nuts - Right Hand Thread - Double Circuit
Ballscrew - Nook Series - Nuts - Right Hand Thread - Double Circuit

Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish.


There is also a good range of Ballscrew - Nook Series - Nuts - Right Hand Thread - Double Circuit on the Small Parts and Bearings website.


Ballscrew - Nook Series - Nuts - Right Hand Thread - Single Circuit
Ballscrew - Nook Series - Nuts - Right Hand Thread - Single Circuit

Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish.


There is also a good range of Ballscrew - Nook Series - Nuts - Right Hand Thread - Single Circuit on the Small Parts and Bearings website.


You may also like

Plungers Ball


Ball Buttons
Ball Buttons

Also known as striker bushings or ball plunger detents. Use with ball or bolt spring plungers for a hard wearing contact area.

Burnished ground hardened steel.


There is also a good range of Ball Buttons on the Small Parts and Bearings website.


Tooling Balls


Balls - Checking - Stainless Steel
Balls - Checking - Stainless Steel

Also see combined categories:
All Fixture and Checking Balls

440C Hardened to RC 55-58.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.


There is also a good range of Balls - Checking - Stainless Steel on the Small Parts and Bearings website.


Balls - Checking - Stainless Steel - With Tapped Shank
Balls - Checking - Stainless Steel - With Tapped Shank

Also see combined categories:
All Fixture and Checking Balls

440C Hardened to RC 55-58.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.


There is also a good range of Balls - Checking - Stainless Steel - With Tapped Shank on the Small Parts and Bearings website.


Balls - Checking - Tungsten Carbide
Balls - Checking - Tungsten Carbide

Also see combined categories:
All Fixture and Checking Balls

RC 65-68

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.


There is also a good range of Balls - Checking - Tungsten Carbide on the Small Parts and Bearings website.


Balls - Fixture - Stainless Steel
Balls - Fixture - Stainless Steel

Also see combined categories:
All Fixture and Checking Balls

440C Hardened to RC 55-58.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.


There is also a good range of Balls - Fixture - Stainless Steel on the Small Parts and Bearings website.


Balls - Fixture - Tungsten Carbide
Balls - Fixture - Tungsten Carbide

Also see combined categories:
All Fixture and Checking Balls

RC 65-68

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.


There is also a good range of Balls - Fixture - Tungsten Carbide on the Small Parts and Bearings website.


Balls - Inspection
Balls - Inspection

Also see combined categories:
All Fixture and Checking Balls

Premium short shank inspection balls are used as reference points for inspection applications in conjunction with coordinate measuring machines to accurately measure the workpiece.

Made from case hardened 8620 steel. Concentricity of ball to shank is 0.00254mm (0.0001 in.) TIR.


There is also a good range of Balls - Inspection on the Small Parts and Bearings website.


Balls - Tooling - One Piece - Construction - Stainless Steel
Balls - Tooling - One Piece - Construction - Stainless Steel

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. 440C Stainless Steel heat treated to 55-58 RC. Precise shoulder base to ball centre line dimension within +/- 0.00508mm.


There is also a good range of Balls - Tooling - One Piece - Construction - Stainless Steel on the Small Parts and Bearings website.


Balls - Tooling - One Piece - Construction - Steel
Balls - Tooling - One Piece - Construction - Steel

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. 1144 steel heat treated to 53-57 RC. Precise shoulder base to ball centre line dimension within +/- 0.00508mm.


There is also a good range of Balls - Tooling - One Piece - Construction - Steel on the Small Parts and Bearings website.


Balls - Tooling - One Piece - Shoulder - Stainless Steel - Press Fit
Balls - Tooling - One Piece - Shoulder - Stainless Steel - Press Fit

Also see combined categories:
All Tooling Balls
All Shoulder Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 440C Stainless Steel heat treated to 55-58 RC.


There is also a good range of Balls - Tooling - One Piece - Shoulder - Stainless Steel - Press Fit on the Small Parts and Bearings website.


Balls - Tooling - One Piece - Shoulder - Stainless Steel - Slip Fit
Balls - Tooling - One Piece - Shoulder - Stainless Steel - Slip Fit

Also see combined categories:
All Tooling Balls
All Shoulder Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 440C Stainless Steel heat treated to 55-58 RC.


There is also a good range of Balls - Tooling - One Piece - Shoulder - Stainless Steel - Slip Fit on the Small Parts and Bearings website.


Balls - Tooling - One Piece - Shoulder - Steel - Press Fit
Balls - Tooling - One Piece - Shoulder - Steel - Press Fit

Also see combined categories:
All Tooling Balls
All Shoulder Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 1144 steel heat treated to 53-57 RC.


There is also a good range of Balls - Tooling - One Piece - Shoulder - Steel - Press Fit on the Small Parts and Bearings website.


Balls - Tooling - One Piece - Shoulder - Steel - Slip Fit
Balls - Tooling - One Piece - Shoulder - Steel - Slip Fit

Also see combined categories:
All Tooling Balls
All Shoulder Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 1144 steel heat treated to 53-57 RC.


There is also a good range of Balls - Tooling - One Piece - Shoulder - Steel - Slip Fit on the Small Parts and Bearings website.


Balls - Tooling - One Piece - Standard - Stainless Steel - Press Fit
Balls - Tooling - One Piece - Standard - Stainless Steel - Press Fit

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

440C Stainless Steel heat treated to 55-58 RC.


There is also a good range of Balls - Tooling - One Piece - Standard - Stainless Steel - Press Fit on the Small Parts and Bearings website.


Balls - Tooling - One Piece - Standard - Stainless Steel - Slip Fit
Balls - Tooling - One Piece - Standard - Stainless Steel - Slip Fit

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

440C Stainless Steel heat treated to 55-58 RC.


There is also a good range of Balls - Tooling - One Piece - Standard - Stainless Steel - Slip Fit on the Small Parts and Bearings website.


Balls - Tooling - One Piece - Standard - Steel - Press Fit
Balls - Tooling - One Piece - Standard - Steel - Press Fit

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

1144 steel heat treated to 53-57 RC.


There is also a good range of Balls - Tooling - One Piece - Standard - Steel - Press Fit on the Small Parts and Bearings website.


Balls - Tooling - One Piece - Standard - Steel - Slip Fit
Balls - Tooling - One Piece - Standard - Steel - Slip Fit

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

1144 steel heat treated to 53-57 RC.


There is also a good range of Balls - Tooling - One Piece - Standard - Steel - Slip Fit on the Small Parts and Bearings website.


Balls - Tooling - Two Piece - Construction - Steel
Balls - Tooling - Two Piece - Construction - Steel

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. 1144 steel heat treated to 53-57 RC. Precise shoulder base to ball centre line dimension within +/- 0.00508mm. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. Construction balls can be pulled into a hole or bushing from below without applying pressure on the ball by using a cap screw in the internally tapped shank.


There is also a good range of Balls - Tooling - Two Piece - Construction - Steel on the Small Parts and Bearings website.


Balls - Tooling - Two Piece - Shoulder - Steel - Press Fit
Balls - Tooling - Two Piece - Shoulder - Steel - Press Fit

Also see combined categories:
All Tooling Balls
All Shoulder Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 1144 steel heat treated to 53-57 RC. Knurled shoulder. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.


There is also a good range of Balls - Tooling - Two Piece - Shoulder - Steel - Press Fit on the Small Parts and Bearings website.


Balls - Tooling - Two Piece - Shoulder - Steel - Slip Fit
Balls - Tooling - Two Piece - Shoulder - Steel - Slip Fit

Also see combined categories:
All Tooling Balls
All Shoulder Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 1144 steel heat treated to 53-57 RC. Knurled shoulder. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.


There is also a good range of Balls - Tooling - Two Piece - Shoulder - Steel - Slip Fit on the Small Parts and Bearings website.


Balls - Tooling - Two Piece - Standard - Steel - Press Fit
Balls - Tooling - Two Piece - Standard - Steel - Press Fit

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

1144 steel heat treated to 53-57 RC. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.


There is also a good range of Balls - Tooling - Two Piece - Standard - Steel - Press Fit on the Small Parts and Bearings website.


Balls - Tooling - Two Piece - Standard - Steel - Slip Fit
Balls - Tooling - Two Piece - Standard - Steel - Slip Fit

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

1144 steel heat treated to 53-57 RC. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.


There is also a good range of Balls - Tooling - Two Piece - Standard - Steel - Slip Fit on the Small Parts and Bearings website.


Knobs Ball


Knobs - Ball - Knock On - Phenolic
Knobs - Ball - Knock On - Phenolic

Moulded from black phenolic resin.

Light Weight. Thermal insulating. Non corrosive. POK Type have a ribbed insert. Shaft should be 0 to 0.007 mm undersized for best results. 712 Type suit standard metric rod.


There is also a good range of Knobs - Ball - Knock On - Phenolic on the Small Parts and Bearings website.


Knobs - Ball - Novo-Grip - Female
Knobs - Ball - Novo-Grip - Female

Also see combined categories:
All Female Threaded Ball Knobs

Ergonomic Shape for easy gripping

Unique styling for a very distinctive look. Belt fluting for non-slip gripping. Black thermoplastic with steel or stainless steel inserts.


There is also a good range of Knobs - Ball - Novo-Grip - Female on the Small Parts and Bearings website.


Knobs - Ball - Novo-Grip - Male
Knobs - Ball - Novo-Grip - Male

Ergonomic Shape for easy gripping

Unique styling for a very distinctive look. Belt fluting for non-slip gripping. Black thermoplastic with steel or stainless steel studs.


There is also a good range of Knobs - Ball - Novo-Grip - Male on the Small Parts and Bearings website.


Knobs - Ball - Threaded - Lateral Grooved
Knobs - Ball - Threaded - Lateral Grooved

Also see combined categories:
All Female Threaded Ball Knobs

Moulded platic control ball handles for machine tools, jigs, fixtures etc.

Stylish grooves to assist with grip. Brass threaded insert.


There is also a good range of Knobs - Ball - Threaded - Lateral Grooved on the Small Parts and Bearings website.


Knobs - Ball - Threaded - Phenolic
Knobs - Ball - Threaded - Phenolic

Also see combined categories:
All Female Threaded Ball Knobs

Moulded from black or red phenolic resin.

Light Weight. Thermal insulating. Non corrosive.


There is also a good range of Knobs - Ball - Threaded - Phenolic on the Small Parts and Bearings website.


Knobs - Ball - Threaded - Phenolic with Shank
Knobs - Ball - Threaded - Phenolic with Shank

Also see combined categories:
All Female Threaded Ball Knobs


There is also a good range of Knobs - Ball - Threaded - Phenolic with Shank on the Small Parts and Bearings website.


Knobs - Ball - Threaded - Plastic with Groove
Knobs - Ball - Threaded - Plastic with Groove

Also see combined categories:
All Female Threaded Ball Knobs

Black plastic ball knobs with a groove around the circumference. Brass threaded insert.


There is also a good range of Knobs - Ball - Threaded - Plastic with Groove on the Small Parts and Bearings website.


Knobs - Ball - Threaded - Plastic with Knurl
Knobs - Ball - Threaded - Plastic with Knurl

Also see combined categories:
All Female Threaded Ball Knobs

Brass threaded insert. Knurled circumference to assist with grip.


There is also a good range of Knobs - Ball - Threaded - Plastic with Knurl on the Small Parts and Bearings website.


Knobs - Ball - Threaded - Polished Aluminium
Knobs - Ball - Threaded - Polished Aluminium

Also see combined categories:
All Female Threaded Ball Knobs

DIN319 Tapped aluminium

Polished with a flash chrome finish.


There is also a good range of Knobs - Ball - Threaded - Polished Aluminium on the Small Parts and Bearings website.


Knobs - Ball - Threaded - Polished or Raw Brass
Knobs - Ball - Threaded - Polished or Raw Brass

Also see combined categories:
All Female Threaded Ball Knobs

CDA 360 Free Machining Brass

Polished balls are fully finished and suitable for decorative and display purposes.


There is also a good range of Knobs - Ball - Threaded - Polished or Raw Brass on the Small Parts and Bearings website.


Knobs - Ball - Threaded - Polished Steel
Knobs - Ball - Threaded - Polished Steel

Also see combined categories:
All Female Threaded Ball Knobs

Low carbon steel 12L14


There is also a good range of Knobs - Ball - Threaded - Polished Steel on the Small Parts and Bearings website.


Knobs - Ball - Threaded - Recessed Top
Knobs - Ball - Threaded - Recessed Top

Also see combined categories:
All Female Threaded Ball Knobs

Brass threaded insert. Phenolic.


There is also a good range of Knobs - Ball - Threaded - Recessed Top on the Small Parts and Bearings website.


Knobs - Ball - Threaded - Soft Touch
Knobs - Ball - Threaded - Soft Touch

Also see combined categories:
All Female Threaded Ball Knobs

Rugged thermoplastic construction with a soft feel. Moulded with a soft rubber shell providing a sure grip. Zinc plated steel insert.


There is also a good range of Knobs - Ball - Threaded - Soft Touch on the Small Parts and Bearings website.


Knobs - Ball - Threaded - Stainless Steel
Knobs - Ball - Threaded - Stainless Steel

Also see combined categories:
All Female Threaded Ball Knobs

303 stainless steel (European grade 1.4305)


There is also a good range of Knobs - Ball - Threaded - Stainless Steel on the Small Parts and Bearings website.


Knobs - Ball - Threaded - Thermoplastic
Knobs - Ball - Threaded - Thermoplastic

Also see combined categories:
All Female Threaded Ball Knobs

With moulded plastic threads, or metalic threaded inserts - brass or steel.


There is also a good range of Knobs - Ball - Threaded - Thermoplastic on the Small Parts and Bearings website.


Knobs - Ball - Threaded - Wrench Flats and Knob-Lok
Knobs - Ball - Threaded - Wrench Flats and Knob-Lok

Also see combined categories:
All Female Threaded Ball Knobs

Unique Knob-Lok features a nylon locking element that resists vibration and prevents back-off

Perfect for high vibrational applications.


There is also a good range of Knobs - Ball - Threaded - Wrench Flats and Knob-Lok on the Small Parts and Bearings website.


Plungers Ball


Plungers - Ball - Push Fit - 303 Stainless Steel
Plungers - Ball - Push Fit - 303 Stainless Steel

Also see combined categories:
All Push Fit Ball Plungers

Unthreaded

Body BSD: Pom (Delrin) BSD-SS: W.-Nr 1.4305 (303) Stainless Steel. Sleeve BSD: Thermoplastic BSD-SS: Stainless Steel. Ball: W.-Nr 1.4034 (420) Stainless Steel. Spring: W.-Nr 1.4310 (301) Stainless Steel. Surface Finish BSD: Ball hardened, bright BSD-SS: Bright.


There is also a good range of Plungers - Ball - Push Fit - 303 Stainless Steel on the Small Parts and Bearings website.




Plungers - Ball - Push Fit - Plastic Body - Plastic Ball
Plungers - Ball - Push Fit - Plastic Body - Plastic Ball

Also see combined categories:
All Push Fit Ball Plungers

Unthreaded. Plastic body and ball.

Body BSD: Pom (Delrin) BSD-SS: W.-Nr 1.4305 (303) Stainless Steel. Sleeve BSD: Thermoplastic BSD-SS: Stainless Steel. Ball: W.-Nr 1.4034 (420) Stainless Steel. Spring: W.-Nr 1.4310 (301) Stainless Steel. Surface Finish BSD: Ball hardened, bright BSD-SS: Bright.


There is also a good range of Plungers - Ball - Push Fit - Plastic Body - Plastic Ball on the Small Parts and Bearings website.


Plungers - Ball - Push Fit - Plastic Body - Stainless Ball
Plungers - Ball - Push Fit - Plastic Body - Stainless Ball

Also see combined categories:
All Push Fit Ball Plungers

Unthreaded.


There is also a good range of Plungers - Ball - Push Fit - Plastic Body - Stainless Ball on the Small Parts and Bearings website.


Plungers - Ball - Push Fit - Stainless Body - Acetal Ball
Plungers - Ball - Push Fit - Stainless Body - Acetal Ball

Also see combined categories:
All Push Fit Ball Plungers

Unthreaded.


There is also a good range of Plungers - Ball - Push Fit - Stainless Body - Acetal Ball on the Small Parts and Bearings website.


Plungers - Ball - Push Fit - Stainless Body - Nylon Ball
Plungers - Ball - Push Fit - Stainless Body - Nylon Ball

Also see combined categories:
All Push Fit Ball Plungers

Unthreaded.


There is also a good range of Plungers - Ball - Push Fit - Stainless Body - Nylon Ball on the Small Parts and Bearings website.


Plungers - Ball - Push Fit - Stainless Body - Plastic Ball
Plungers - Ball - Push Fit - Stainless Body - Plastic Ball

Also see combined categories:
All Push Fit Ball Plungers

Unthreaded.


There is also a good range of Plungers - Ball - Push Fit - Stainless Body - Plastic Ball on the Small Parts and Bearings website.


Plungers - Ball - Push Fit - Steel Body - Acetal Ball
Plungers - Ball - Push Fit - Steel Body - Acetal Ball

Also see combined categories:
All Push Fit Ball Plungers

Unthreaded.


There is also a good range of Plungers - Ball - Push Fit - Steel Body - Acetal Ball on the Small Parts and Bearings website.


Plungers - Ball - Push Fit - Steel Body - Nylon Ball
Plungers - Ball - Push Fit - Steel Body - Nylon Ball

Also see combined categories:
All Push Fit Ball Plungers

Unthreaded.


There is also a good range of Plungers - Ball - Push Fit - Steel Body - Nylon Ball on the Small Parts and Bearings website.


Plungers - Ball - Push Fit - Steel Body - Stainless Ball
Plungers - Ball - Push Fit - Steel Body - Stainless Ball

Also see combined categories:
All Push Fit Ball Plungers

Unthreaded.


There is also a good range of Plungers - Ball - Push Fit - Steel Body - Stainless Ball on the Small Parts and Bearings website.


Plungers - Ball - Threaded - 303 Stainless Steel
Plungers - Ball - Threaded - 303 Stainless Steel

Also see combined categories:
All Threaded Ball Plungers

Items shown with Long-Lok have a dry threadlocking sealant applied to thread.


There is also a good range of Plungers - Ball - Threaded - 303 Stainless Steel on the Small Parts and Bearings website.


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Miniature Bearings Australia offers 122791 products in 2704 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Miniature Bearings Australia offers 122791 products in 2704 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.