Ball Splines Linear Categories


Category Matches

Ball Splines Linear

TopHide Pictures

Linear Ball Splines - Bearings - Unflanged
Linear Ball Splines - Bearings - Unflanged

Search Rating: 100%

Also see combined categories:
All Linear Ball Splines

Use with Linear Ball Spline Shaft.

Related Information:

Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Linear Ball Splines - Bearings - Unflanged.

Linear Slides

TopHide Pictures

Linear - Assemblies - Ball Slide - Precision
Linear - Assemblies - Ball Slide - Precision

Search Rating: 50%

These precision ball slides have a typical coefficient of friction of 0.003 and provide straight line accuracy of 0.0005mm per mm of travel.

At load capacity a life of 250 million mm of travel can be expected. The expected life at half load capacity is 2.5 billion mm. Factory preload adjustment prevents sideplay and backlash. Lightweight aluminium carriage and base with high load capacity. Four tapped and threaded carriage holes and counterbored base holes simplify installation and component mounting. Long life, self cleaning ball bearing needs no lubrication. Positional repeatability 0.005mm. Clear anodised finish.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Linear - Assemblies - Ball Slide - Precision.

Linear Slide Assemblies - Ball - Pre-Loaded - Compliant
Linear Slide Assemblies - Ball - Pre-Loaded - Compliant

Search Rating: 50%

Also see combined categories:
All Linear Slide Assemblies

Pre-loaded ball slides provide an acceptable level of accuracy of 0.001mm per mm for most linear motion applications. Considerably lower cost than crossed roller slides.

Uses a conventional hardened steel rod raceway and balls. Incorporates an elastomer spine and shock absorbing backup gib. Provides even and continuous preload, whilst minimising the effects of impact and shock. Tolerant to contamination and can operate of millions of cycles without lubrication. 8-32 UNC mounting holes.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Linear Slide Assemblies - Ball - Pre-Loaded - Compliant.

Linear Slide Assemblies - Ball - Pre-Loaded - Hard Gib
Linear Slide Assemblies - Ball - Pre-Loaded - Hard Gib

Search Rating: 50%

Also see combined categories:
All Linear Slide Assemblies

Pre-loaded ball slides provide an acceptable level of accuracy of 0.001mm per mm for most linear motion applications. Considerably lower cost than crossed roller slides.

Hard gib preload. Tolerant to contamination and can operate of millions of cycles without lubrication. 8-32 UNC mounting holes.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Linear Slide Assemblies - Ball - Pre-Loaded - Hard Gib.

Linear Bearings

TopHide Pictures

Bearings - Linear - Ball - Closed
Bearings - Linear - Ball - Closed

Search Rating: 50%

Also see combined categories:
All Closed Linear Ball Bearings

Standard closed type to run on standard 60HRC shafts with h6 tolerances

Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous.

Related Information:

Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bearings - Linear - Ball - Closed.

Bearings - Linear - Ball - Miniature - Super High Precision
Bearings - Linear - Ball - Miniature - Super High Precision

Search Rating: 50%

Also see combined categories:
All Closed Linear Ball Bearings

High Precision Corrosion Resistant Miniature Linear Bearings.

High Precision Swiss Made, Accurate Guiding, Smooth Running. High Load Capacity. Tolerances --- d (+0.008 / -0.000 mm) D (+0.000 / -0.010 mm). Recommended Outer ring fitted with interferance of 1-3 Microns or retained by Circlips. Shafts (not included) should be 60-63 Rockwell C hardness with tolerances +0.000 / -0.006 mm.

Related Information:

Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bearings - Linear - Ball - Miniature - Super High Precision.

Bearings - Linear - Ball - Stainless Steel - Closed
Bearings - Linear - Ball - Stainless Steel - Closed

Search Rating: 50%

Also see combined categories:
All Closed Linear Ball Bearings

Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.

Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous.

Related Information:

Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bearings - Linear - Ball - Stainless Steel - Closed.

Bearings - Linear - Ball - Thomson Precision Steel - Closed
Bearings - Linear - Ball - Thomson Precision Steel - Closed

Search Rating: 50%

Also see combined categories:
All Thomson Linear Ball Bearings

For running on shafts fixed at the ends.

Related Information:

Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bearings - Linear - Ball - Thomson Precision Steel - Closed.

Linear Slides

TopHide Pictures

Slides - Linear - Recirculating Ball - Standard
Slides - Linear - Recirculating Ball - Standard

Search Rating: 49%

Also see combined categories:
All Linear Slides

The BSR precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.

Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100oC (Constant), +120oC (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants. Note BSR1530SL and BSR2040SL can not be mounted from inside of track rail.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Slides - Linear - Recirculating Ball - Standard.

Slides - Linear - Non Recirculating Ball - Standard
Slides - Linear - Non Recirculating Ball - Standard

Search Rating: 49%

Also see combined categories:
All Linear Slides

The BSP precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.

Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100oC (Constant), +120oC (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Slides - Linear - Non Recirculating Ball - Standard.

Posi Drive Stage - Ball Slide
Posi Drive Stage - Ball Slide

Search Rating: 49%

Also see combined categories:
All Posi-Drive Stages

Compact economical Posi Drive Stages take the work out of designing linear motion control systems.

These stages require no alignment of components and install with only 4 standard fasteners. Fitted with anti backlash 9.525mm diameter leadscrews with 2.54mm lead and zero backlash multibeam couplings. NEMA 23 motor mounts. Straight line accuracy up to 0.00254mm per 25.4mm of travel. Repeatability 0.00254mm.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Posi Drive Stage - Ball Slide.

Linear Slide Assemblies - Cross Roller
Linear Slide Assemblies - Cross Roller

Search Rating: 48%

Also see combined categories:
All Linear Slide Assemblies

Higher load capacity than precision ball slide assemblies. High cycling rates. Tolerant of shock and overhanging loads.

Accuracy of 0.00254mm per 25.4mm of travel. Repeatability 0.00254mm. Not as naturally cleaning as ball slides. A good choice for environments protected from dust, and when heavy loads are a consideration. Positive stops prevent over-travel. Rollers improve capacity 8-10 times that of balls. Alternately crossed rollers handle force in any direction. Lightweight aluminium carriage and base. Interchangeable with many types of ball slides. Four tapped carriage holes and two counter bored base holes simplify installation and component mounting.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Linear Slide Assemblies - Cross Roller.

Ball Screws Rolled

TopHide Pictures

Ballscrew - Thomson Saginaw
Ballscrew - Thomson Saginaw

Search Rating: 47%

Also see combined categories:
All Ball Screws

Offer 90% efficiency converting rotary to linear motion with low coefficient of friction. Match all components within the Thomson Saginaw range only.

When replacing screws, hydraulics or pneumatics, they allow the use of smaller, less expensive drive motors and reduce the need for auxiliary equipment. Offer dependable accuracy and repeatability, Made off high quality alloy steel, hardened to Rockwell 56-60C.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Ballscrew - Thomson Saginaw.

Linear Slides

TopHide Pictures

Slides - Drawer - Front Disconnect - Friction - 19mm Ext
Slides - Drawer - Front Disconnect - Friction - 19mm Ext

Search Rating: 46%

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted two member slide. Friction brake allows drawer to come to a slow stop. Front disconnects by pulling firmly on the drawer until it releases. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Slides - Drawer - Front Disconnect - Friction - 19mm Ext.

Slides - Drawer - Front Disconnect - Lever - Full Ext
Slides - Drawer - Front Disconnect - Lever - Full Ext

Search Rating: 46%

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Front disconnects by lifting a lever lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Slides - Drawer - Front Disconnect - Lever - Full Ext.

Slides - Drawer - Front Disconnect - Friction - 19mm Ext - Undercarriage
Slides - Drawer - Front Disconnect - Friction - 19mm Ext - Undercarriage

Search Rating: 46%

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Undercarriage mounted two member slide. Friction brake allows drawer to come to a slow stop. Only one required per drawer. Requires 16 M4 or 8 Gauge Pan Head Screws (not included). Shipped with a bracket and two plastic tracks.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Slides - Drawer - Front Disconnect - Friction - 19mm Ext - Undercarriage.

Slides - Drawer - Front Disconnect - Latch Lever - Full Ext
Slides - Drawer - Front Disconnect - Latch Lever - Full Ext

Search Rating: 46%

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Front disconnects by pressing a drawer latch lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Slides - Drawer - Front Disconnect - Latch Lever - Full Ext.

Slides - Drawer - Quick Disconnect - Medium Duty - Full Ext
Slides - Drawer - Quick Disconnect - Medium Duty - Full Ext

Search Rating: 46%

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Positive stop slide with a quick disconnect.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Slides - Drawer - Quick Disconnect - Medium Duty - Full Ext.

Slides - Drawer - Stainless - Front Disconnect - Lever - 19mm Ext
Slides - Drawer - Stainless - Front Disconnect - Lever - 19mm Ext

Search Rating: 46%

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted two member slide. Positive locking mechanism keeps drawer locked in the open position until actively released. Front disconnects by pressing a drawer latch lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Slides - Drawer - Stainless - Front Disconnect - Lever - 19mm Ext.

Slides - Drawer - Stainless - No Disconnect - Heavy Duty - 19mm Ext
Slides - Drawer - Stainless - No Disconnect - Heavy Duty - 19mm Ext

Search Rating: 46%

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted two member slide. Positive stop slide that will not disconnect once installed. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Slides - Drawer - Stainless - No Disconnect - Heavy Duty - 19mm Ext.

Slides - Drawer - Stainless - No Disconnect - Heavy Duty - Full Ext
Slides - Drawer - Stainless - No Disconnect - Heavy Duty - Full Ext

Search Rating: 46%

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Positive stop slide that will not disconnect once installed.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Slides - Drawer - Stainless - No Disconnect - Heavy Duty - Full Ext.

Slides - Drawer - Stainless - No Disconnect - Medium Duty - 19mm Ext
Slides - Drawer - Stainless - No Disconnect - Medium Duty - 19mm Ext

Search Rating: 46%

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted two member slide. Positive stop slide that will not disconnect once installed. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Slides - Drawer - Stainless - No Disconnect - Medium Duty - 19mm Ext.

Slides - Drawer - Stainless - No Disconnect - Medium Duty - Full Ext
Slides - Drawer - Stainless - No Disconnect - Medium Duty - Full Ext

Search Rating: 46%

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Positive stop slide that will not disconnect once installed.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Slides - Drawer - Stainless - No Disconnect - Medium Duty - Full Ext.

Linear Bearings

TopHide Pictures

Bearings - Linear - Sliding - Stainless - PTFE - Closed
Bearings - Linear - Sliding - Stainless - PTFE - Closed

Search Rating: 46%

Also see combined categories:
All Sliding Linear Bearings

Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.

Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bearings - Linear - Sliding - Stainless - PTFE - Closed.

Bearings - Linear - Sliding - Stainless - PTFE - Open
Bearings - Linear - Sliding - Stainless - PTFE - Open

Search Rating: 46%

Also see combined categories:
All Sliding Linear Bearings

Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.

Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bearings - Linear - Sliding - Stainless - PTFE - Open.

Linear Slides

TopHide Pictures

Linear - Mini Rail - Self-Lubricating - Carriage
Linear - Mini Rail - Self-Lubricating - Carriage

Search Rating: 45%

Additional carriages for the Mini-Rail system. Match by rail width.

Low profile self-lubricating linear guide system with one piece carriage design. Excellent alternative to linear ball bearing systems. Precision series made from RC70 ceramic coated rail with self lubricating Frelon Gold. Dampens vibration and tolerates shock loads. Will not rust. No metal to metal contact. No balls or rolling elements to trap contamination, skid or damage rail. Operation is consistent, smooth and quiet. Maintenance free. Used in packaging machines, medical equipment, wash-down and harsh environments.

Related Information:

Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Linear - Mini Rail - Self-Lubricating - Carriage.

Linear - Mini Rail - Self-Lubricating - Carriage and Rail
Linear - Mini Rail - Self-Lubricating - Carriage and Rail

Search Rating: 45%

Comes with one carriage. Spare carriages sold separately - match by rail width.

Low profile self-lubricating linear guide system with one piece carriage design. Excellent alternative to linear ball bearing systems. Precision series made from RC70 ceramic coated rail with self lubricating Frelon Gold. Dampens vibration and tolerates shock loads. Will not rust. No metal to metal contact. No balls or rolling elements to trap contamination, skid or damage rail. Operation is consistent, smooth and quiet. Maintenance free. Used in packaging machines, medical equipment, wash-down and harsh environments.

Related Information:

Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Linear - Mini Rail - Self-Lubricating - Carriage and Rail.


Show all items starting with
A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z   1   2   3   4   5   6   7   8   9  





Other Store Pages

Click Page Banner Below

Top

Main Pages

Click Page Banner Below

Top





Top



Site Summary

Freight Rates
Terms and Conditions
Privacy Policy

Miniature Bearings Australia offers 112476 products in 2808 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.