Ball Screws Rolled Categories

Ballscrew - Thomson Saginaw

Also see combined categories:
All Ball Screws

Offer 90% efficiency converting rotary to linear motion with low coefficient of friction. Match all components within the Thomson Saginaw range only.

When replacing screws, hydraulics or pneumatics, they allow the use of smaller, less expensive drive motors and reduce the need for auxiliary equipment. Offer dependable accuracy and repeatability, Made off high quality alloy steel, hardened to Rockwell 56-60C.

There is also a good range of Ballscrew - Thomson Saginaw on the Small Parts and Bearings website.

You may also be interested in

Screws Grub

Socket Set Screws - Rolling Ball Tip - Carbon Steel

Also see combined categories:
All Rolling Ball Tip Grub Screws
All Grub Screws

Rolling ball tip for locating into a hole

Rolling ball set screws are not designed to bear heavy loads. Used to lightly fasten fragile work pieces. We would recommend testing if you plan to use them in a load bearing application.

Related Information:

Socket Set Screws Master PDF

There is also a good range of Socket Set Screws - Rolling Ball Tip - Carbon Steel on the Small Parts and Bearings website.

Socket Set Screws - Rolling Ball Tip - Stainless Steel

Also see combined categories:
All Rolling Ball Tip Grub Screws
All Grub Screws

Rolling ball tip for locating into a hole

Rolling ball set screws are not designed to bear heavy loads. Used to lightly fasten fragile work pieces. We would recommend testing if you plan to use them in a load bearing application.

Related Information:

Socket Set Screws Master PDF

There is also a good range of Socket Set Screws - Rolling Ball Tip - Stainless Steel on the Small Parts and Bearings website.

Ball Screw Accessories

Ballscrew - Thomson Saginaw - Accessories

Also see combined categories:
All Ball Screws

Wiper Kits and Flanges for Ball Nuts. Match all components within the Thomson Saginaw range only.

There is also a good range of Ballscrew - Thomson Saginaw - Accessories on the Small Parts and Bearings website.

Ballscrew - Thomson Saginaw - Nut

Also see combined categories:
All Ball Screws

Ball Nuts to Suit Thomson Saginaw ball screws. Match all components within the Thomson Saginaw range only.

All Right hand thread only.

There is also a good range of Ballscrew - Thomson Saginaw - Nut on the Small Parts and Bearings website.

Ball Screws Nook Series

Ballscrew - Nook Series - Flanges

Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish.

There is also a good range of Ballscrew - Nook Series - Flanges on the Small Parts and Bearings website.

Ball Transfers

Ball Transfer Units - Screw Stem - Brass and Aluminium

Also see combined categories:
All Screw Fit Ball Transfers

Single ball bearings units for conveyor systems

Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.

There is also a good range of Ball Transfer Units - Screw Stem - Brass and Aluminium on the Small Parts and Bearings website.

Ball Transfer Units - Screw Stem - Steel - Precision

Also see combined categories:
All Screw Fit Ball Transfers

Single ball bearings units for conveyor systems

Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.

There is also a good range of Ball Transfer Units - Screw Stem - Steel - Precision on the Small Parts and Bearings website.

Ball Screws 16mm SDP

Ballscrew - 16mm Nuts - Pillow Block

Also see combined categories:
All Ball Screws

Includes ball nut. Match all components within the 16mm range only.

Antibacklash. Repeatability 0.01mm, accuracy 0.1mm/300mm when used with our 16mm screws. Hardened ground and polished Cf53 steel to HRC62 +/-2. Balls hardened HRC63 +/- 2.

There is also a good range of Ballscrew - 16mm Nuts - Pillow Block on the Small Parts and Bearings website.

Ball Screws Nook Series

Ballscrew - Nook Series - Right Hand

Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

High quality alloy steel, induction hardened to RC 56-60. Protective black oxide finish. Lead accurate by at least 0.00083mm per mm.

There is also a good range of Ballscrew - Nook Series - Right Hand on the Small Parts and Bearings website.

Ball Screws Ground

Ballscrew - Ground - Dia 4mm - Lead 1mm

Also see combined categories:
All Ball Screws

Not for sale outside of Australia and New Zealand

There is also a good range of Ballscrew - Ground - Dia 4mm - Lead 1mm on the Small Parts and Bearings website.

Ball Screw Accessories

Mounts - Universal - For Acme Thread and Ballscrews

Use grade 8 hex socket head cap screws for mounting.

Related Information:

Cylindrical Bobbin Mounts PDF Quick Guide

There is also a good range of Mounts - Universal - For Acme Thread and Ballscrews on the Small Parts and Bearings website.

Ball Screws Nook Series

Ballscrew - Nook Series - Nuts - Right Hand Thread - Double Circuit

Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish.

There is also a good range of Ballscrew - Nook Series - Nuts - Right Hand Thread - Double Circuit on the Small Parts and Bearings website.

Ballscrew - Nook Series - Nuts - Right Hand Thread - Single Circuit

Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish.

There is also a good range of Ballscrew - Nook Series - Nuts - Right Hand Thread - Single Circuit on the Small Parts and Bearings website.

Screws Grub

Socket Set Screws - Flat Tip - Aligning - Carbon Steel

Also see combined categories:
All Flat Aligning Tip Grub Screws
All Grub Screws

Grub screws with a pivoting flat tip. The ball can pivot up to 9 Deg. To fasten the object securely to misaligned parts.

Also known as a flat ball tip set screw or a clamping screw.

Related Information:

Socket Set Screws Master PDF

There is also a good range of Socket Set Screws - Flat Tip - Aligning - Carbon Steel on the Small Parts and Bearings website.

Socket Set Screws - Flat Tip - Aligning - Stainless Steel

Also see combined categories:
All Flat Aligning Tip Grub Screws
All Grub Screws

Grub screws with a pivoting flat tip. The ball can pivot up to 9 Deg. To fasten the object securely to misaligned parts.

Also known as a flat ball tip set screw or a clamping screw.

Related Information:

Socket Set Screws Master PDF

There is also a good range of Socket Set Screws - Flat Tip - Aligning - Stainless Steel on the Small Parts and Bearings website.

Tooling Balls

Balls - Tooling - Two Piece - Construction - Steel

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. 1144 steel heat treated to 53-57 RC. Precise shoulder base to ball centre line dimension within +/- 0.00508mm. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. Construction balls can be pulled into a hole or bushing from below without applying pressure on the ball by using a cap screw in the internally tapped shank.

Related Information:

Balls Master Catalogue PDF

There is also a good range of Balls - Tooling - Two Piece - Construction - Steel on the Small Parts and Bearings website.

Slides - Drawer - Stainless - No Disconnect - Heavy Duty - 19mm Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted two member slide. Positive stop slide that will not disconnect once installed. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).

There is also a good range of Slides - Drawer - Stainless - No Disconnect - Heavy Duty - 19mm Ext on the Small Parts and Bearings website.

Slides - Drawer - Stainless - No Disconnect - Medium Duty - 19mm Ext

Also see combined categories:
All Drawer Slides

Side mounted two member slide. Positive stop slide that will not disconnect once installed. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).

There is also a good range of Slides - Drawer - Stainless - No Disconnect - Medium Duty - 19mm Ext on the Small Parts and Bearings website.

Slides - Drawer - Front Disconnect - Friction - 19mm Ext

Also see combined categories:
All Drawer Slides

Side mounted two member slide. Friction brake allows drawer to come to a slow stop. Front disconnects by pulling firmly on the drawer until it releases. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).

There is also a good range of Slides - Drawer - Front Disconnect - Friction - 19mm Ext on the Small Parts and Bearings website.

Slides - Drawer - Stainless - Front Disconnect - Lever - 19mm Ext

Also see combined categories:
All Drawer Slides

Side mounted two member slide. Positive locking mechanism keeps drawer locked in the open position until actively released. Front disconnects by pressing a drawer latch lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).

There is also a good range of Slides - Drawer - Stainless - Front Disconnect - Lever - 19mm Ext on the Small Parts and Bearings website.

Slides - Drawer - Front Disconnect - Friction - 19mm Ext - Undercarriage

Also see combined categories:
All Drawer Slides

Undercarriage mounted two member slide. Friction brake allows drawer to come to a slow stop. Only one required per drawer. Requires 16 M4 or 8 Gauge Pan Head Screws (not included). Shipped with a bracket and two plastic tracks.

There is also a good range of Slides - Drawer - Front Disconnect - Friction - 19mm Ext - Undercarriage on the Small Parts and Bearings website.

Slides - Drawer - Front Disconnect - Lever - Full Ext

Also see combined categories:
All Drawer Slides

Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Front disconnects by lifting a lever lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).

There is also a good range of Slides - Drawer - Front Disconnect - Lever - Full Ext on the Small Parts and Bearings website.

Pins - Ball Lock - Flanged Receptacles

Also see combined categories:
All Ball Lock Receptacles

Provide a permanent and proper mating hole for commercial and industrial type quick release ball lock pins.

Designed to be used on materials or in applications where the positive lock detent pin does not have anything to lock against. Pin does not protrude past the bottom of the receptacle so they are ideal for blind hole applications. 303 Stainless Steel. Mounted with screws, rivets or bolts. The quick release ball lock pins are inserted from the flanged end, and the ball extends into the wider opening at the top of the receptacle.

Related Information:

Master Pins Catalogue PDF

There is also a good range of Pins - Ball Lock - Flanged Receptacles on the Small Parts and Bearings website.

Slides - Drawer - Front Disconnect - Latch Lever - Full Ext

Also see combined categories:
All Drawer Slides

Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Front disconnects by pressing a drawer latch lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).

There is also a good range of Slides - Drawer - Front Disconnect - Latch Lever - Full Ext on the Small Parts and Bearings website.

Screws - Roof Bolt - Steel

Also see combined categories:
All Machine Screws

Metal Thread Screws. Metric and BSW only. Supplied with nut.

Nuts sold seperately - See Nuts.

Related Information:

Nuts

There is also a good range of Screws - Roof Bolt - Steel on the Small Parts and Bearings website.

Screws - Hex Head - Steel - Zinc Plated

Also see combined categories:
All Hex Head Screws

BSW and METRIC - Bolts

Related Information:

Nuts

There is also a good range of Screws - Hex Head - Steel - Zinc Plated on the Small Parts and Bearings website.

Screws - Shoulder - Slotted Shallow Head - Carbon Steel

Also see combined categories:
All Shoulder Screws

Also known as stripper bolts.

There is also a good range of Screws - Shoulder - Slotted Shallow Head - Carbon Steel on the Small Parts and Bearings website.

Screws - Shoulder - Socket Head - 303 Stainless

Also see combined categories:
All Shoulder Screws

Also known as stripper bolts.

There is also a good range of Screws - Shoulder - Socket Head - 303 Stainless on the Small Parts and Bearings website.

Screws - Shoulder - Socket Head - 416 Stainless

Also see combined categories:
All Shoulder Screws

Also known as stripper bolts.

There is also a good range of Screws - Shoulder - Socket Head - 416 Stainless on the Small Parts and Bearings website.

Screws - Shoulder - Socket Head - Carbon Steel

Also see combined categories:
All Shoulder Screws

Also known as stripper bolts.

There is also a good range of Screws - Shoulder - Socket Head - Carbon Steel on the Small Parts and Bearings website.

Screws - Shoulder - Slotted Head - Stainless

Also see combined categories:
All Shoulder Screws

303 Stainless Steel

Also known as stripper bolts.

There is also a good range of Screws - Shoulder - Slotted Head - Stainless on the Small Parts and Bearings website.

Screws - Shoulder - Jig and Fixture - Steel

Also see combined categories:
All Shoulder Screws

Used in construction of tool, jig and fixture work. 4140L heat treated steel with black oxide finish.

Also known as stripper bolts.

There is also a good range of Screws - Shoulder - Jig and Fixture - Steel on the Small Parts and Bearings website.

Tools - Screw Extractors

Also see combined categories:
All Tools

The quick and easy way to remove broken screws, bolts, pipes and studs.

Note! You will also need a drill bit of the correct size for each extractor.

There is also a good range of Tools - Screw Extractors on the Small Parts and Bearings website.

Screws - Thumb - 1-4 Turn

Also see combined categories:
All Thumb Screws

Related Information:

Ball Screws Rolled Categories

You may also be interested in

Screws Grub

Ball Screw Accessories

Ball Screws Nook Series

Ball Transfers

Ball Screws 16mm SDP

Ball Screws Nook Series

Ball Screws Ground

Ball Screw Accessories

Ball Screws Nook Series

Screws Grub

Tooling Balls

Main Pages

Products