Miniature Bearings Australia Pty Ltd

Ball Screws Nook Series Categories


Ballscrew - Nook Series - Flanges
Ballscrew - Nook Series - Flanges


Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish. This category may be available in the new MBA online store at Ballscrew - Nook Series - Flanges.

There is also a good range of Ballscrew - Nook Series - Flanges on the Small Parts and Bearings website.


Ballscrew - Nook Series - Right Hand
Ballscrew - Nook Series - Right Hand


Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

High quality alloy steel, induction hardened to RC 56-60. Protective black oxide finish. Lead accurate by at least 0.00083mm per mm. This category may be available in the new MBA online store at Ballscrew - Nook Series - Right Hand.

There is also a good range of Ballscrew - Nook Series - Right Hand on the Small Parts and Bearings website.


Ballscrew - Nook Series - Nuts - Right Hand Thread - Double Circuit
Ballscrew - Nook Series - Nuts - Right Hand Thread - Double Circuit


Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish.

There is also a good range of Ballscrew - Nook Series - Nuts - Right Hand Thread - Double Circuit on the Small Parts and Bearings website.


Ballscrew - Nook Series - Nuts - Right Hand Thread - Single Circuit
Ballscrew - Nook Series - Nuts - Right Hand Thread - Single Circuit


Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish.

There is also a good range of Ballscrew - Nook Series - Nuts - Right Hand Thread - Single Circuit on the Small Parts and Bearings website.


Couplings - Reli-a-flex - Short Series - Set Screw Type
Couplings - Reli-a-flex - Short Series - Set Screw Type

Also see combined categories:
All Helical and Slit Couplings

From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).

Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.

Related Information:

There is also a good range of Couplings - Reli-a-flex - Short Series - Set Screw Type on the Small Parts and Bearings website.


Ballscrew - Thomson Saginaw
Ballscrew - Thomson Saginaw

Also see combined categories:
All Ball Screws

Offer 90% efficiency converting rotary to linear motion with low coefficient of friction. Match all components within the Thomson Saginaw range only.

When replacing screws, hydraulics or pneumatics, they allow the use of smaller, less expensive drive motors and reduce the need for auxiliary equipment. Offer dependable accuracy and repeatability, Made off high quality alloy steel, hardened to Rockwell 56-60C. This category may be available in the new MBA online store at Ballscrew - Thomson Saginaw.

There is also a good range of Ballscrew - Thomson Saginaw on the Small Parts and Bearings website.


Ballscrew - Thomson Saginaw - Accessories
Ballscrew - Thomson Saginaw - Accessories

Also see combined categories:
All Ball Screws

Wiper Kits and Flanges for Ball Nuts. Match all components within the Thomson Saginaw range only.

This category may be available in the new MBA online store at Ballscrew - Thomson Saginaw - Accessories.

There is also a good range of Ballscrew - Thomson Saginaw - Accessories on the Small Parts and Bearings website.


Ballscrew - Thomson Saginaw - Nut
Ballscrew - Thomson Saginaw - Nut

Also see combined categories:
All Ball Screws

Ball Nuts to Suit Thomson Saginaw ball screws. Match all components within the Thomson Saginaw range only.

All Right hand thread only. This category may be available in the new MBA online store at Ballscrew - Thomson Saginaw - Nut.

There is also a good range of Ballscrew - Thomson Saginaw - Nut on the Small Parts and Bearings website.


Ball Transfer Units - Screw Stem - Brass and Aluminium
Ball Transfer Units - Screw Stem - Brass and Aluminium

Also see combined categories:
All Screw Fit Ball Transfers

Single ball bearings units for conveyor systems

Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms. This category may be available in the new MBA online store at Ball Transfer Units - Screw Stem - Brass and Aluminium.

There is also a good range of Ball Transfer Units - Screw Stem - Brass and Aluminium on the Small Parts and Bearings website.


Ball Transfer Units - Screw Stem - Stainless - Precision
Ball Transfer Units - Screw Stem - Stainless - Precision

Also see combined categories:
All Screw Fit Ball Transfers

Single ball bearings units for conveyor systems

Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms. This category may be available in the new MBA online store at Ball Transfer Units - Screw Stem - Stainless - Precision.

There is also a good range of Ball Transfer Units - Screw Stem - Stainless - Precision on the Small Parts and Bearings website.


Ball Transfer Units - Screw Stem - Steel - Precision
Ball Transfer Units - Screw Stem - Steel - Precision

Also see combined categories:
All Screw Fit Ball Transfers

Single ball bearings units for conveyor systems

Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms. This category may be available in the new MBA online store at Ball Transfer Units - Screw Stem - Steel - Precision.

There is also a good range of Ball Transfer Units - Screw Stem - Steel - Precision on the Small Parts and Bearings website.


Ballscrew - Ground - Dia 4mm - Lead 1mm
Ballscrew - Ground - Dia 4mm - Lead 1mm

Also see combined categories:
All Ball Screws

Not for sale outside of Australia and New Zealand

This category may be available in the new MBA online store at Ballscrew - Ground - Dia 4mm - Lead 1mm.

There is also a good range of Ballscrew - Ground - Dia 4mm - Lead 1mm on the Small Parts and Bearings website.


Socket Set Screws - Rolling Ball Tip - Carbon Steel
Socket Set Screws - Rolling Ball Tip - Carbon Steel

Also see combined categories:
All Rolling Ball Tip Grub Screws
All Grub Screws

Rolling ball tip for locating into a hole

Rolling ball set screws are not designed to bear heavy loads. Used to lightly fasten fragile work pieces. We would recommend testing if you plan to use them in a load bearing application. This category may be available in the new MBA online store at Socket Set Screws - Rolling Ball Tip - Carbon Steel.

Related Information:

There is also a good range of Socket Set Screws - Rolling Ball Tip - Carbon Steel on the Small Parts and Bearings website.


Socket Set Screws - Rolling Ball Tip - Stainless Steel
Socket Set Screws - Rolling Ball Tip - Stainless Steel

Also see combined categories:
All Rolling Ball Tip Grub Screws
All Grub Screws

Rolling ball tip for locating into a hole

Rolling ball set screws are not designed to bear heavy loads. Used to lightly fasten fragile work pieces. We would recommend testing if you plan to use them in a load bearing application. This category may be available in the new MBA online store at Socket Set Screws - Rolling Ball Tip - Stainless Steel.

Related Information:

There is also a good range of Socket Set Screws - Rolling Ball Tip - Stainless Steel on the Small Parts and Bearings website.


Bearings - Ball - Double Row - Self Aligning - Tapered Bore - Heavy Series
Bearings - Ball - Double Row - Self Aligning - Tapered Bore - Heavy Series

Also see combined categories:
All Double Row Ball Bearings
All Self Aligning Ball Bearings

Use with H300 heavy series adaptor sleeves or AH300 Withdrawal sleeves


Related Information:


Bearings - Ball - Double Row - Self Aligning - Tapered Bore - Light Series
Bearings - Ball - Double Row - Self Aligning - Tapered Bore - Light Series

Also see combined categories:
All Double Row Ball Bearings
All Self Aligning Ball Bearings

Use with H200 light series adaptor sleeves or AH200 Withdrawal sleeves


Related Information:


Bearings - Ball - Semi-Ground - Sealed
Bearings - Ball - Semi-Ground - Sealed

Also see combined categories:
All Radial Ball Bearings

Radial ball bearings. This series is precision ground on all contact surfaces except the bore. Recommended for lighter loads and maximum speed of 3000rpm. Bore tolerance is +0.127/-0.000, OD tolerance is +0.000/-0.013 and width is +0.000/-0.127

This category may be available in the new MBA online store at Bearings - Ball - Semi-Ground - Sealed.

There is also a good range of Bearings - Ball - Semi-Ground - Sealed on the Small Parts and Bearings website.


Bearings - Ball - Semi-Ground - Shielded
Bearings - Ball - Semi-Ground - Shielded

Also see combined categories:
All Radial Ball Bearings

Radial ball bearings. This series is precision ground on all contact surfaces except the bore. Recommended for lighter loads and maximum speed of 3000rpm. Bore tolerance is +0.127/-0.000, OD tolerance is +0.000/-0.013 and width is +0.000/-0.127

This category may be available in the new MBA online store at Bearings - Ball - Semi-Ground - Shielded.

There is also a good range of Bearings - Ball - Semi-Ground - Shielded on the Small Parts and Bearings website.


Slides - Linear - Recirculating Ball - Standard
Slides - Linear - Recirculating Ball - Standard

Also see combined categories:
All Linear Slides

The BSR precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.

Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100oC (Constant), +120oC (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants. Note BSR1530SL and BSR2040SL can not be mounted from inside of track rail.

There is also a good range of Slides - Linear - Recirculating Ball - Standard on the Small Parts and Bearings website.


Socket Set Screws - Flat Tip - Aligning - Carbon Steel
Socket Set Screws - Flat Tip - Aligning - Carbon Steel

Also see combined categories:
All Flat Aligning Tip Grub Screws
All Grub Screws

Grub screws with a pivoting flat tip. The ball can pivot up to 9 Deg. To fasten the object securely to misaligned parts.

Also known as a flat ball tip set screw or a clamping screw. This category may be available in the new MBA online store at Socket Set Screws - Flat Tip - Aligning - Carbon Steel.

Related Information:

There is also a good range of Socket Set Screws - Flat Tip - Aligning - Carbon Steel on the Small Parts and Bearings website.


Socket Set Screws - Flat Tip - Aligning - Stainless Steel
Socket Set Screws - Flat Tip - Aligning - Stainless Steel

Also see combined categories:
All Flat Aligning Tip Grub Screws
All Grub Screws

Grub screws with a pivoting flat tip. The ball can pivot up to 9 Deg. To fasten the object securely to misaligned parts.

Also known as a flat ball tip set screw or a clamping screw. This category may be available in the new MBA online store at Socket Set Screws - Flat Tip - Aligning - Stainless Steel.

Related Information:

There is also a good range of Socket Set Screws - Flat Tip - Aligning - Stainless Steel on the Small Parts and Bearings website.


Slides - Linear - Non Recirculating Ball - Standard
Slides - Linear - Non Recirculating Ball - Standard

Also see combined categories:
All Linear Slides

The BSP precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.

Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100oC (Constant), +120oC (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants.

There is also a good range of Slides - Linear - Non Recirculating Ball - Standard on the Small Parts and Bearings website.


Pulleys - Timing - 10.000mm Pitch - AT10 - 16mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 16mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:

There is also a good range of Pulleys - Timing - 10.000mm Pitch - AT10 - 16mm Wide - Through Bore on the Small Parts and Bearings website.


Pulleys - Timing - 10.000mm Pitch - AT10 - 25mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 25mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:

There is also a good range of Pulleys - Timing - 10.000mm Pitch - AT10 - 25mm Wide - Through Bore on the Small Parts and Bearings website.


Pulleys - Timing - 10.000mm Pitch - AT10 - 32mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 32mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:

There is also a good range of Pulleys - Timing - 10.000mm Pitch - AT10 - 32mm Wide - Through Bore on the Small Parts and Bearings website.


Pulleys - Timing - 10.000mm Pitch - AT10 - 50mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 50mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:

There is also a good range of Pulleys - Timing - 10.000mm Pitch - AT10 - 50mm Wide - Through Bore on the Small Parts and Bearings website.


Pins - Hammer Drive - Flat Head
Pins - Hammer Drive - Flat Head

Also see combined categories:
All Hammer Drive Pins

Used to replace screws where the need to remove the pin is unlikely.

Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.

Related Information:

There is also a good range of Pins - Hammer Drive - Flat Head on the Small Parts and Bearings website.


Housings - Bearing - Square - Miniature
Housings - Bearing - Square - Miniature


Aluminium housings to suit standard radial ball bearings.

Use with standard radial ball bearings. Bearing not included. Can be through screwed from the top using socket head cap screws. Can be bolted from the bottom using the pre-tapped holes. Made from Aluminium 6082-T6 Black Anodised.

There is also a good range of Housings - Bearing - Square - Miniature on the Small Parts and Bearings website.


Balls - Tooling - Two Piece - Construction - Steel
Balls - Tooling - Two Piece - Construction - Steel

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. 1144 steel heat treated to 53-57 RC. Precise shoulder base to ball centre line dimension within +/- 0.00508mm. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. Construction balls can be pulled into a hole or bushing from below without applying pressure on the ball by using a cap screw in the internally tapped shank.

Related Information:

There is also a good range of Balls - Tooling - Two Piece - Construction - Steel on the Small Parts and Bearings website.


Pulleys - Timing - 5.080mm Pitch - XL - 6.4mm Wide - Through Bore
Pulleys - Timing -  5.080mm Pitch - XL -  6.4mm Wide - Through Bore

Also see combined categories:
All XL 5.08mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit XL Series 5.080mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide.

Aluminium alloy. Finished bore with set screw locking. This category may be available in the new MBA online store at Pulleys - Timing - 5.080mm Pitch - XL - 6.4mm Wide - Through Bore.

Related Information:

There is also a good range of Pulleys - Timing - 5.080mm Pitch - XL - 6.4mm Wide - Through Bore on the Small Parts and Bearings website.


Pulleys - Timing - 5.000mm Pitch - AT5 - 10mm Wide - Through Bore
Pulleys - Timing -  5.000mm Pitch - AT5 - 10mm Wide - Through Bore

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT5 Series belts

Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size. This category may be available in the new MBA online store at Pulleys - Timing - 5.000mm Pitch - AT5 - 10mm Wide - Through Bore.

Related Information:

There is also a good range of Pulleys - Timing - 5.000mm Pitch - AT5 - 10mm Wide - Through Bore on the Small Parts and Bearings website.


Pulleys - Timing - 5.000mm Pitch - AT5 - 16mm Wide - Through Bore
Pulleys - Timing -  5.000mm Pitch - AT5 - 16mm Wide - Through Bore

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT5 Series belts

Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size. This category may be available in the new MBA online store at Pulleys - Timing - 5.000mm Pitch - AT5 - 16mm Wide - Through Bore.

Related Information:

There is also a good range of Pulleys - Timing - 5.000mm Pitch - AT5 - 16mm Wide - Through Bore on the Small Parts and Bearings website.


Pulleys - Timing - 5.000mm Pitch - AT5 - 25mm Wide - Through Bore
Pulleys - Timing -  5.000mm Pitch - AT5 - 25mm Wide - Through Bore

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT5 Series belts

Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size. This category may be available in the new MBA online store at Pulleys - Timing - 5.000mm Pitch - AT5 - 25mm Wide - Through Bore.

Related Information:

There is also a good range of Pulleys - Timing - 5.000mm Pitch - AT5 - 25mm Wide - Through Bore on the Small Parts and Bearings website.


Pulleys - Timing - 5.080mm Pitch - XL - 9.5mm Wide - Through Bore
Pulleys - Timing -  5.080mm Pitch - XL -  9.5mm Wide - Through Bore

Also see combined categories:
All XL 5.08mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit XL Series 5.080mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide.

Aluminium alloy and Black Oxide coated steel. Finished bore with set screw locking. Unfinished types requires drilling and tapping. Bore requires machining to finished size. This category may be available in the new MBA online store at Pulleys - Timing - 5.080mm Pitch - XL - 9.5mm Wide - Through Bore.

Related Information:

There is also a good range of Pulleys - Timing - 5.080mm Pitch - XL - 9.5mm Wide - Through Bore on the Small Parts and Bearings website.


Rail Systems - Type 2 - Linear - Precision - Carriage - Chrome - Narrow
Rail Systems - Type 2 - Linear - Precision - Carriage - Chrome - Narrow


Match with rail by size column 1. Thomson 500 Series provide long life, exceptional rigidity, high dynamic and static load capabilities in all directions.

Accommodates high moment loads and maintains high running accuracy. Improved machine accuracies and rigidity resulting in reduced vibration and extended machine and tool life. Low drag longitudinal seals protect the the balls and ball path from contamination. Thin dense chrome.

Related Information:

There is also a good range of Rail Systems - Type 2 - Linear - Precision - Carriage - Chrome - Narrow on the Small Parts and Bearings website.


Rail Systems - Type 2 - Linear - Precision - Carriage - Chrome - Standard
Rail Systems - Type 2 - Linear - Precision - Carriage - Chrome - Standard


Match with rail by size column 1. Thomson 500 Series provide long life, exceptional rigidity, high dynamic and static load capabilities in all directions.

Accommodates high moment loads and maintains high running accuracy. Improved machine accuracies and rigidity resulting in reduced vibration and extended machine and tool life. Low drag longitudinal seals protect the the balls and ball path from contamination. Thin dense chrome.

Related Information:

There is also a good range of Rail Systems - Type 2 - Linear - Precision - Carriage - Chrome - Standard on the Small Parts and Bearings website.


Rail Systems - Type 3 - Linear - Precision - Carriage - Carbon Steel - Narrow
Rail Systems - Type 3 - Linear - Precision - Carriage - Carbon Steel - Narrow


Match with rail by size column 1. Thomson 500 Series provide long life, exceptional rigidity, high dynamic and static load capabilities in all directions.

Accommodates high moment loads and maintains high running accuracy. Improved machine accuracies and rigidity resulting in reduced vibration and extended machine and tool life. Low drag longitudinal seals protect the the balls and ball path from contamination.

Related Information:

There is also a good range of Rail Systems - Type 3 - Linear - Precision - Carriage - Carbon Steel - Narrow on the Small Parts and Bearings website.


Rail Systems - Type 3 -Linear - Precision - Carriage - Carbon Steel - Standard
Rail Systems - Type 3 -Linear - Precision - Carriage - Carbon Steel - Standard


Match with rail by size column 1. Thomson 500 Series provide long life, exceptional rigidity, high dynamic and static load capabilities in all directions.

Accommodates high moment loads and maintains high running accuracy. Improved machine accuracies and rigidity resulting in reduced vibration and extended machine and tool life. Low drag longitudinal seals protect the the balls and ball path from contamination.

Related Information:

There is also a good range of Rail Systems - Type 3 -Linear - Precision - Carriage - Carbon Steel - Standard on the Small Parts and Bearings website.


Slides - Drawer - Front Disconnect - Friction - 19mm Ext - Undercarriage
Slides - Drawer - Front Disconnect - Friction - 19mm Ext - Undercarriage

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Undercarriage mounted two member slide. Friction brake allows drawer to come to a slow stop. Only one required per drawer. Requires 16 M4 or 8 Gauge Pan Head Screws (not included). Shipped with a bracket and two plastic tracks.

There is also a good range of Slides - Drawer - Front Disconnect - Friction - 19mm Ext - Undercarriage on the Small Parts and Bearings website.


Pins - Ball Lock - Flanged Receptacles
Pins - Ball Lock - Flanged Receptacles

Also see combined categories:
All Ball Lock Receptacles

Provide a permanent and proper mating hole for commercial and industrial type quick release ball lock pins.

Designed to be used on materials or in applications where the positive lock detent pin does not have anything to lock against. Pin does not protrude past the bottom of the receptacle so they are ideal for blind hole applications. 303 Stainless Steel. Mounted with screws, rivets or bolts. The quick release ball lock pins are inserted from the flanged end, and the ball extends into the wider opening at the top of the receptacle.

Related Information:

There is also a good range of Pins - Ball Lock - Flanged Receptacles on the Small Parts and Bearings website.


Locknuts - Stainless Insert
Locknuts - Stainless Insert


Simplify the assembly and reduce costs involved in securing ball bearings. One piece item where the locking function is performed by a spring peened into the top of the nut.

Nut Body: Low Carbon Steel. Locking Insert: Stainless Steel Hardness HB 201-269. The spring bears on the flank of the shaft thread with force (P) generating reaction force (Pí) in the screw threads with a resulting high friction torque (prevailing torque). Unique slim body design. Secure locking without keyway and tab washer. One piece construction reduces stock and allows simpler, quicker assembly. Simple infinite adjustment. Re-usable up to 100 times. Resists vibration and shock. Equally effective for rotation in either direction even with rapid reversals.

Related Information:

There is also a good range of Locknuts - Stainless Insert on the Small Parts and Bearings website.


Screws - Roof Bolt - Steel
Screws - Roof Bolt - Steel

Also see combined categories:
All Machine Screws

Metal Thread Screws. Metric and BSW only. Supplied with nut.

Nuts sold seperately - See Nuts. This category may be available in the new MBA online store at Screws - Roof Bolt - Steel.

Related Information:

There is also a good range of Screws - Roof Bolt - Steel on the Small Parts and Bearings website.


Screws - Hex Head - Steel - Zinc Plated
Screws - Hex Head - Steel - Zinc Plated

Also see combined categories:
All Hex Head Screws

BSW and METRIC - Bolts

This category may be available in the new MBA online store at Screws - Hex Head - Steel - Zinc Plated.

Related Information:

There is also a good range of Screws - Hex Head - Steel - Zinc Plated on the Small Parts and Bearings website.


Tools - Screw Extractors
Tools - Screw Extractors

Also see combined categories:
All Tools

The quick and easy way to remove broken screws, bolts, pipes and studs.

Note! You will also need a drill bit of the correct size for each extractor. This category may be available in the new MBA online store at Tools - Screw Extractors.

There is also a good range of Tools - Screw Extractors on the Small Parts and Bearings website.


Screws - Shoulder - Philips Head - Stainless
Screws - Shoulder - Philips Head - Stainless

Also see combined categories:
All Shoulder Screws

303 Stainless Steel

Also known as stripper bolts. This category may be available in the new MBA online store at Screws - Shoulder - Philips Head - Stainless.

There is also a good range of Screws - Shoulder - Philips Head - Stainless on the Small Parts and Bearings website.


Screws - Shoulder - Slotted Head - Stainless
Screws - Shoulder - Slotted Head - Stainless

Also see combined categories:
All Shoulder Screws

303 Stainless Steel

Also known as stripper bolts. This category may be available in the new MBA online store at Screws - Shoulder - Slotted Head - Stainless.

There is also a good range of Screws - Shoulder - Slotted Head - Stainless on the Small Parts and Bearings website.


Screws - Shoulder - Socket Head - 303 Stainless
Screws - Shoulder - Socket Head - 303 Stainless

Also see combined categories:
All Shoulder Screws

Also known as stripper bolts. This category may be available in the new MBA online store at Screws - Shoulder - Socket Head - 303 Stainless.

There is also a good range of Screws - Shoulder - Socket Head - 303 Stainless on the Small Parts and Bearings website.


Screws - Shoulder - Socket Head - 316 Stainless
Screws - Shoulder - Socket Head - 316 Stainless

Also see combined categories:
All Shoulder Screws

Also known as stripper bolts. This category may be available in the new MBA online store at Screws - Shoulder - Socket Head - 316 Stainless.

There is also a good range of Screws - Shoulder - Socket Head - 316 Stainless on the Small Parts and Bearings website.


Screws - Shoulder - Socket Head - 416 Stainless
Screws - Shoulder - Socket Head - 416 Stainless

Also see combined categories:
All Shoulder Screws

Also known as stripper bolts. This category may be available in the new MBA online store at Screws - Shoulder - Socket Head - 416 Stainless.

There is also a good range of Screws - Shoulder - Socket Head - 416 Stainless on the Small Parts and Bearings website.


Screws - Shoulder - Socket Head - Carbon Steel
Screws - Shoulder - Socket Head - Carbon Steel

Also see combined categories:
All Shoulder Screws

Also known as stripper bolts. This category may be available in the new MBA online store at Screws - Shoulder - Socket Head - Carbon Steel.

There is also a good range of Screws - Shoulder - Socket Head - Carbon Steel on the Small Parts and Bearings website.





Main Pages

5 Axis Machine Tool Bearings About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Charity Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Distributor Locations Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form McMaster Carr Cross Reference PDF Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Satellite Reaction Wheels SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 209441 products in 2115 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 209441 products in 2115 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.