Ball Screws Ground Categories
Ballscrews - Ground - Dia 4mm - Lead 1mm
Not for sale outside of Australia and New Zealand
This category may be available in the new MBA online store at Ballscrews - Ground - Dia 4mm - Lead 1mm.
There is also a good range of Ballscrews - Ground - Dia 4mm - Lead 1mm on the Small Parts and Bearings website.
You may also be interested in
Balls Plastic
Balls - Plastic - Acrylic
Resistance to weather and sunlight. Good abrasion resistance.
Diametrical tolerances typically + / - 0.08 or 0.13 mm depending on size. Acrylic (Methyl Methacrylate). Resistance to weather and sunlight. Good abrasion resistance. Water clear transparent. Polished. Ground and Polished.
Related Information:
There is also a good range of Balls - Plastic - Acrylic on the Small Parts and Bearings website.
Shafting Precision Ground
Supports - Pedestal Two Bolt
For linear shafting.
Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel. This category may be available in the new MBA online store at Supports - Pedestal Two Bolt.
Related Information:
There is also a good range of Supports - Pedestal Two Bolt on the Small Parts and Bearings website.
Pins - Ball Lock - T Handle - Stainless Steel - Heavy Duty
17-4 PH or PH15-7MO stainless steel spindle and shank. Ground handling pins used in the handling of aircraft and service equipment. Tee handle.
Positive lock detent pins. 300 Grade Stainless Components. 440C Stainless Balls. This category may be available in the new MBA online store at Pins - Ball Lock - T Handle - Stainless Steel - Heavy Duty.
Related Information:
There is also a good range of Pins - Ball Lock - T Handle - Stainless Steel - Heavy Duty on the Small Parts and Bearings website.
Ballscrews - Thomson Saginaw
Offer 90% efficiency converting rotary to linear motion with low coefficient of friction. Match all components within the Thomson Saginaw range only.
When replacing screws, hydraulics or pneumatics, they allow the use of smaller, less expensive drive motors and reduce the need for auxiliary equipment. Offer dependable accuracy and repeatability, Made off high quality alloy steel, hardened to Rockwell 56-60C. This category may be available in the new MBA online store at Ballscrews - Thomson Saginaw.
There is also a good range of Ballscrews - Thomson Saginaw on the Small Parts and Bearings website.
Bearings - Single Row Semi-Ground - Sealed
Radial ball bearings. This series is precision ground on all contact surfaces except the bore. Recommended for lighter loads and maximum speed of 3000rpm. Bore tolerance is +0.127/-0.000, OD tolerance is +0.000/-0.013 and width is +0.000/-0.127
This category may be available in the new MBA online store at Bearings - Single Row Semi-Ground - Sealed.
There is also a good range of Bearings - Single Row Semi-Ground - Sealed on the Small Parts and Bearings website.
Bearings - Single Row Semi-Ground - Shielded
Radial ball bearings. This series is precision ground on all contact surfaces except the bore. Recommended for lighter loads and maximum speed of 3000rpm. Bore tolerance is +0.127/-0.000, OD tolerance is +0.000/-0.013 and width is +0.000/-0.127
This category may be available in the new MBA online store at Bearings - Single Row Semi-Ground - Shielded.
There is also a good range of Bearings - Single Row Semi-Ground - Shielded on the Small Parts and Bearings website.
Ballscrew Accessories - Thomson Saginaw
Wiper Kits and Flanges for Ball Nuts. Match all components within the Thomson Saginaw range only.
This category may be available in the new MBA online store at Ballscrew Accessories - Thomson Saginaw.
There is also a good range of Ballscrew Accessories - Thomson Saginaw on the Small Parts and Bearings website.
Ballscrew Nuts - Thomson Saginaw
Ball Nuts to Suit Thomson Saginaw ball screws. Match all components within the Thomson Saginaw range only.
All Right hand thread only. This category may be available in the new MBA online store at Ballscrew Nuts - Thomson Saginaw.
There is also a good range of Ballscrew Nuts - Thomson Saginaw on the Small Parts and Bearings website.
Ballscrew Flanges - Nook Series
Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.
Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish. This category may be available in the new MBA online store at Ballscrew Flanges - Nook Series.
There is also a good range of Ballscrew Flanges - Nook Series on the Small Parts and Bearings website.
Ball Transfer Units - Screw Stem - Brass and Aluminium
Single ball bearings units for conveyor systems
Applications include measuring equipment and light weight coil handlers. Max Load is applicable when used as a transfer, not as a castor. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms. This category may be available in the new MBA online store at Ball Transfer Units - Screw Stem - Brass and Aluminium.
There is also a good range of Ball Transfer Units - Screw Stem - Brass and Aluminium on the Small Parts and Bearings website.
Ball Transfer Units - Screw Stem - Stainless - Precision
Single ball bearings units for conveyor systems
Applications include measuring equipment and light weight coil handlers. Max Load is applicable when used as a transfer, not as a castor. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms. This category may be available in the new MBA online store at Ball Transfer Units - Screw Stem - Stainless - Precision.
There is also a good range of Ball Transfer Units - Screw Stem - Stainless - Precision on the Small Parts and Bearings website.
Ball Transfer Units - Screw Stem - Steel - Precision
Single ball bearings units for conveyor systems
Applications include measuring equipment and light weight coil handlers. Max Load is applicable when used as a transfer, not as a castor. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms. This category may be available in the new MBA online store at Ball Transfer Units - Screw Stem - Steel - Precision.
There is also a good range of Ball Transfer Units - Screw Stem - Steel - Precision on the Small Parts and Bearings website.
Ballscrews - Nook Series - Right Hand
Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.
High quality alloy steel, induction hardened to RC 56-60. Protective black oxide finish. Lead accurate by at least 0.00083mm per mm. This category may be available in the new MBA online store at Ballscrews - Nook Series - Right Hand.
There is also a good range of Ballscrews - Nook Series - Right Hand on the Small Parts and Bearings website.
Socket Set Screws - Rolling Ball Tip - Carbon Steel
Rolling ball tip for locating into a hole
Rolling ball set screws are not designed to bear heavy loads. Used to lightly fasten fragile work pieces. We would recommend testing if you plan to use them in a load bearing application. Ball materials include carbon steel, brass, Polyacetal or 440C Stainless Steel. This category may be available in the new MBA online store at Socket Set Screws - Rolling Ball Tip - Carbon Steel.
Related Information:
There is also a good range of Socket Set Screws - Rolling Ball Tip - Carbon Steel on the Small Parts and Bearings website.
Socket Set Screws - Rolling Ball Tip - Stainless Steel
Rolling ball tip for locating into a hole
Rolling ball set screws are not designed to bear heavy loads. Used to lightly fasten fragile work pieces. We would recommend testing if you plan to use them in a load bearing application. Various ball materials include Alumina, Polyacetal or 440C Stainless Steel. This category may be available in the new MBA online store at Socket Set Screws - Rolling Ball Tip - Stainless Steel.
Related Information:
There is also a good range of Socket Set Screws - Rolling Ball Tip - Stainless Steel on the Small Parts and Bearings website.
Bearings - Double Row Ball Semi Precision - Acetal with Glass Balls
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from Ground Glass - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 oC to 100 oC Continuous.
Related Information:
There is also a good range of Bearings - Double Row Ball Semi Precision - Acetal with Glass Balls on the Small Parts and Bearings website.
Ballscrew Nuts - Nook Series - Right Hand Thread - Double Circuit
Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.
Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish.
There is also a good range of Ballscrew Nuts - Nook Series - Right Hand Thread - Double Circuit on the Small Parts and Bearings website.
Ballscrew Nuts - Nook Series - Right Hand Thread - Single Circuit
Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.
Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish.
There is also a good range of Ballscrew Nuts - Nook Series - Right Hand Thread - Single Circuit on the Small Parts and Bearings website.
Balls - Tooling - One Piece - Shoulder - Stainless Steel - Press Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 440C Stainless Steel heat treated to 55-58 RC.
Related Information:
There is also a good range of Balls - Tooling - One Piece - Shoulder - Stainless Steel - Press Fit on the Small Parts and Bearings website.
Balls - Tooling - One Piece - Shoulder - Stainless Steel - Slip Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 440C Stainless Steel heat treated to 55-58 RC.
Related Information:
There is also a good range of Balls - Tooling - One Piece - Shoulder - Stainless Steel - Slip Fit on the Small Parts and Bearings website.
Socket Set Screws - Flat Tip - Aligning - Carbon Steel
Grub screws with a pivoting flat tip. The ball can pivot up to 9 Deg. To fasten the object securely to misaligned parts.
Also known as a flat ball tip set screw or a clamping screw. Selection of tips include carbon steel, 440C Stainless steel and Polyacetal. This category may be available in the new MBA online store at Socket Set Screws - Flat Tip - Aligning - Carbon Steel.
Related Information:
There is also a good range of Socket Set Screws - Flat Tip - Aligning - Carbon Steel on the Small Parts and Bearings website.
Socket Set Screws - Flat Tip - Aligning - Stainless Steel
Grub screws with a pivoting flat tip. The ball can pivot up to 9 Deg. To fasten the object securely to misaligned parts.
Also known as a flat ball tip set screw or a clamping screw. This category may be available in the new MBA online store at Socket Set Screws - Flat Tip - Aligning - Stainless Steel.
Related Information:
There is also a good range of Socket Set Screws - Flat Tip - Aligning - Stainless Steel on the Small Parts and Bearings website.
Bearings - Plastic - PEEK with 316 Stainless Steel Balls
PEEK (Polyetheretherketone), is a high temperature, high-performance engineering polymer.
Races made from PEEK - Balls made from Ground Glass - Cages from PEEK. PEEK offers chemical and water resistance similar to PPS (Polyphenylene Sulfide) but can operate at higher temperatures. PEEK can be used continuously to 338 Deg F (170 Deg C) and in hot water or steam without permanent loss in physical properties. Wear, Chemical & Hydrolysis Resistant. Exceptional performance over a wide range of temperatures and extreme conditions. Low Smoke and Toxic Gas Emission.
Related Information:
There is also a good range of Bearings - Plastic - PEEK with 316 Stainless Steel Balls on the Small Parts and Bearings website.
Inserts - Thread Repair Sets Recoil
Recoil inserts are screwed directly into an enlarged tapped hole. A tap and installation tool is included with these kits.
Stainless inserts. Contents: Ground intermediate (2nd) tap. Inserts. Installation/tang break off tool. Full instructions. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.
There is also a good range of Inserts - Thread Repair Sets Recoil on the Small Parts and Bearings website.
Ball Buttons
Also known as striker bushings or ball plunger detents. Use with ball or bolt spring plungers for a hard wearing contact area.
Burnished ground hardened steel. This category may be available in the new MBA online store at Ball Buttons.
There is also a good range of Ball Buttons on the Small Parts and Bearings website.
Housings - Square - Miniature
Aluminium housings to suit standard radial ball bearings.
Use with standard radial ball bearings. Bearing not included. Can be through screwed from the top using socket head cap screws. Can be bolted from the bottom using the pre-tapped holes. Made from Aluminium 6082-T6 Black Anodised.
There is also a good range of Housings - Square - Miniature on the Small Parts and Bearings website.
Rail Supports - With Shaft - One Piece
One piece construction made from 6061-T6 Aluminium with ceramic coating to Mil-8625. Suitable for use with Frelon lined linear bearings.
Not suitable for linear ball bearings. Weld spatter, paints and other contaminants will not stick to the shaft. Vibration resistant and non-magnetic. Not suitable for harsh washdown environments. This category may be available in the new MBA online store at Rail Supports - With Shaft - One Piece.
Related Information:
There is also a good range of Rail Supports - With Shaft - One Piece on the Small Parts and Bearings website.
Balls - Tooling - Two Piece - Construction - Steel
High quality tooling balls provide a precise reference point for critical machining operations.
Ball and shank are concentric within 5 microns (0.0002 in.) TIR. 1144 steel heat treated to 53-57 RC. Precise shoulder base to ball centre line dimension within +/- 0.00508mm. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. Construction balls can be pulled into a hole or bushing from below without applying pressure on the ball by using a cap screw in the internally tapped shank.
Related Information:
There is also a good range of Balls - Tooling - Two Piece - Construction - Steel on the Small Parts and Bearings website.
Bearings - Linear Ball - Chrome Steel - Closed
Standard closed type to run on standard 60HRC shafts with h6 tolerances
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous. This category may be available in the new MBA online store at Bearings - Linear Ball - Chrome Steel - Closed.
Related Information:
Bearings - Plastic - Acetal with Glass Balls
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from Ground Glass - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 oC to 100 oC Continuous. This category may be available in the new MBA online store at Bearings - Plastic - Acetal with Glass Balls.
Related Information:
There is also a good range of Bearings - Plastic - Acetal with Glass Balls on the Small Parts and Bearings website.
Bearings - Linear Ball - Stainless Steel - Closed
Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous. This category may be available in the new MBA online store at Bearings - Linear Ball - Stainless Steel - Closed.
Related Information:
There is also a good range of Bearings - Linear Ball - Stainless Steel - Closed on the Small Parts and Bearings website.
Bearings - Plastic - PVDF with 316 Stainless Steel Balls
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from PVDF - Balls made from Ground Glass - Cages from PVDF. Kynar -tm- PVDF (Polyvinylidene Fluoride) is a high performance engineering polymer. Kynar -tm- has provided superior chemical resistance properties in critical contact applications for food, pharmaceutical, and semiconductor industries for over 20 years. For chemical and high temperature resistance, low permeability and high mechanical strength. This category may be available in the new MBA online store at Bearings - Plastic - PVDF with 316 Stainless Steel Balls.
Related Information:
There is also a good range of Bearings - Plastic - PVDF with 316 Stainless Steel Balls on the Small Parts and Bearings website.
Balls - Tooling - One Piece - Shoulder - Steel - Press Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 1144 steel heat treated to 53-57 RC. This category may be available in the new MBA online store at Balls - Tooling - One Piece - Shoulder - Steel - Press Fit.
Related Information:
There is also a good range of Balls - Tooling - One Piece - Shoulder - Steel - Press Fit on the Small Parts and Bearings website.
Balls - Tooling - One Piece - Shoulder - Steel - Slip Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 1144 steel heat treated to 53-57 RC. This category may be available in the new MBA online store at Balls - Tooling - One Piece - Shoulder - Steel - Slip Fit.
Related Information:
There is also a good range of Balls - Tooling - One Piece - Shoulder - Steel - Slip Fit on the Small Parts and Bearings website.
Balls - Tooling - Two Piece - Shoulder - Steel - Press Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 1144 steel heat treated to 53-57 RC. Knurled shoulder. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. This category may be available in the new MBA online store at Balls - Tooling - Two Piece - Shoulder - Steel - Press Fit.
Related Information:
There is also a good range of Balls - Tooling - Two Piece - Shoulder - Steel - Press Fit on the Small Parts and Bearings website.
Balls - Tooling - Two Piece - Shoulder - Steel - Slip Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 1144 steel heat treated to 53-57 RC. Knurled shoulder. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. This category may be available in the new MBA online store at Balls - Tooling - Two Piece - Shoulder - Steel - Slip Fit.
Related Information:
There is also a good range of Balls - Tooling - Two Piece - Shoulder - Steel - Slip Fit on the Small Parts and Bearings website.
Bearings - Plastic - Polypropylene with Glass Balls
Good chemical, thermal and electrical properties with moderate strength, Not UV stabilised, but meets FDA standard and is USDA approved.
Races made from Polypropylene - Balls made from Ground Glass - Cages from polypropylene. Lubrication - Water Lubrication or can be run dry. Max Temperature - 60 oC Continuous. This category may be available in the new MBA online store at Bearings - Plastic - Polypropylene with Glass Balls.
Related Information:
Shafting - Ground - Hobby - Steel
Silversteel shafting for hobbies. Not suitable for precision bearings.
Suitable for use with plastic gears, bushes, couplings etc. Not recommended for use with precision steel or stainless steel bearings. Some sizes have special features such as serrations or small barbs (noted in description). Unground ends. Ideal for axles in robotic applications and educational projects.
Related Information:
Shafting - Ground - Precision - Chrome Plated
Precision ground shafting. AISI C1060 and chrome plated for corrosion resistance. Case hardened and recommended for use with precision bearings. Ends are not plated.
Case hardened to 60-65 Rockwell C. Chrome plated for corrosion resistance. This category may be available in the new MBA online store at Shafting - Ground - Precision - Chrome Plated.
There is also a good range of Shafting - Ground - Precision - Chrome Plated on the Small Parts and Bearings website.
Shafting - Ground - Precision - High Carbon Steel
Precision ground shafting. AISI C1060. Hardened and recommended for use with precision bearings.
This category may be available in the new MBA online store at Shafting - Ground - Precision - High Carbon Steel.
Related Information:
There is also a good range of Shafting - Ground - Precision - High Carbon Steel on the Small Parts and Bearings website.
Shafting - Ground - Precision - Stainless 303 Grade
Precision ground shafting.
This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 303 Grade.
Related Information:
There is also a good range of Shafting - Ground - Precision - Stainless 303 Grade on the Small Parts and Bearings website.
Shafting - Ground - Precision - Stainless 420 Grade Hardened
Precision ground shafting. 420 grade. Hardened and recommended for use with precision bearings.
This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 420 Grade Hardened.
Related Information:
There is also a good range of Shafting - Ground - Precision - Stainless 420 Grade Hardened on the Small Parts and Bearings website.
Shafting - Ground - Precision - Stainless 440C Grade Hardened
Precision ground shafting. 440C grade. Hardened and recommended for use with precision bearings.
This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 440C Grade Hardened.
Related Information:
There is also a good range of Shafting - Ground - Precision - Stainless 440C Grade Hardened on the Small Parts and Bearings website.
Shafting - Ground - Precision - Titanium - High Strength
Titanium shafting available in oversized and undersized tolerances
Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5, 6Al-4V, TC4 is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent. Shaft with undersized tolerances is suitable for use with precision ground bearings wih inner rings. HRC 36. Surface Finish Ra 0.8-1.6 um. Not suitable for running needle bearings directly. Shaft with oversized tolerances is suitable for pulleys or gears requiring interference fits, or for machining to your required tolerances.
Related Information:
There is also a good range of Shafting - Ground - Precision - Titanium - High Strength on the Small Parts and Bearings website.
Shafting - Ground - Precision - Titanium - Ti-Gr2-TA1
CP2 Commercially Pure Titanium Grade 2. Tensile Strength 35.2 kgf/mm2. Yield Strength 28.2 kgf/mm2. Elongation 20 Percent.
Commercially pure for general industrial corrosion applications. UNS R50400. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.3, O 0.25, Ti Balance. Shaft with undersized tolerances is suitable for use with precision ground bearings with inner rings. HRB 74. Surface Finish Ra 0.8-1.6 um. Not suitable for running needle bearings directly. Shaft with oversized tolerances is suitable for pulleys or gears requiring interference fits, or for machining to your required tolerances.
Related Information:
There is also a good range of Shafting - Ground - Precision - Titanium - Ti-Gr2-TA1 on the Small Parts and Bearings website.
Shafts - Idler
Ready made precision ground idler shafts.
Internal grease hole can be accessed by drilling if required. Use with your idler pulleys. Can be used with the idler tensioners listed on this site or use in your own design. This category may be available in the new MBA online store at Shafts - Idler.
Related Information:
There is also a good range of Shafts - Idler on the Small Parts and Bearings website.
Shafts - Pinion
This category may be available in the new MBA online store at Shafts - Pinion.
There is also a good range of Shafts - Pinion on the Small Parts and Bearings website.
Slides - Drawer - Front Disconnect - Friction - 19mm Ext - Standard
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted two member slide. Friction brake allows drawer to come to a slow stop. Front disconnects by pulling firmly on the drawer until it releases. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
There is also a good range of Slides - Drawer - Front Disconnect - Friction - 19mm Ext - Standard on the Small Parts and Bearings website.
Slides - Drawer - Front Disconnect - Friction - 19mm Ext - Undercarriage
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Undercarriage mounted two member slide. Friction brake allows drawer to come to a slow stop. Only one required per drawer. Requires 16 M4 or 8 Gauge Pan Head Screws (not included). Shipped with a bracket and two plastic tracks.
There is also a good range of Slides - Drawer - Front Disconnect - Friction - 19mm Ext - Undercarriage on the Small Parts and Bearings website.
Main Pages
5 Axis Machine Tool Bearings
About Us
Acetal Bearings PDF
ADR and SKF PDF
Anderton Circlips Cross Reference PDF
Ball Lock Pins PDF
Balls List
Balls PDF
Barden Bearings Cross Reference PDF
Bearings List
Brands
Ceramic Bearings PDF
Circlips PDF
Clearance Items List
Clevis Pins PDF
Contact Us
Corrosion Resistant Bearings PDF
Dental Bearings
Disc Springs PDF
Distributor Locations
Dowel Pins PDF
Dowel Pins
Economy Bearings PDF
Essentra Cross Reference PDF
Flocast Cross Reference PDF
Freight Rates and Shipping Times
Frequently Asked Questions
General Information about MBA
Hammer Drive Pins PDF
High Speed Bearings PDF
Hobby Clearance
Hobby Information
K&S Metals Cross Reference PDF
Key Steel PDF
Knobs PDF
Large Bearings
Leveling Mounts PDF
Mailorder Form
Metallic Bushes PDF
Miniature Precison Bearings Cross Reference PDF
Miscellaneous Brands Cross Reference PDF
Nordex Cross Reference PDF
NSK and NTN Cross Reference PDF
Ondrives Cross Reference PDF
O-Rings PDF
Pins PDF
Plastic Bearings PDF
Polyvee Belts and Pulleys PDF
Precision Shim Washers PDF
Privacy
Push On and Push In Rings PDF
Reid Supply Cross Reference PDF
Rod & Tube PDF
Roll Pins PDF
Satellite Reaction Wheels
Screws PDF
SDP-SI Designatronics Cross Reference PDF
Seeger Circlips Cross Reference PDF
Shaft Collars PDF
Shim Sheet PDF
Shoulder Screws PDF
Sintered Bronze Bushes PDF
Sintered Bronze Cross Reference PDF
Small Bearings
Small Parts Inc Cross Reference PDF
Snap Rings PDF
Socket Set Screws PDF
Solid Bronze Bushes PDF
Spring Steel Strip PDF
Springs PDF
Standard Ball Bearing Range PDF
Super Precision Bearings PDF
Taper Pins PDF
Technical Information
Terms
Thrust Bearings PDF
Thumb Screws and Nuts PDF
Timing Belts and Pulleys Cross Reference PDF
Timing Belts PDF
Timing Pulley Stock PDF
Timing Pulleys PDF
Vibration Mounts PDF
Washers and Spacers PDF
Wave Washers PDF
Domains
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)
Miniature Bearings Australia offers 227672 products in 2186 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.
