Miniature Bearings Australia Pty Ltd

Ball Parallels Categories


Parallels - Ball
Parallels - Ball


Used for handling large work in drill presses or band saw machines.

Placed between work and machine so work can be easily moved. Black Oxide finish with 9.525mm hardened steel balls. Balls are exposed both sides of sheet.

There is also a good range of Parallels - Ball on the Small Parts and Bearings website.


You may also be interested in

Bearings Double Row Ball




Joints - Dual Eye - Parallel
Joints - Dual Eye - Parallel


Maintenance free - self lubricating thermoplastic. Mechanical joining linkage. Self aligning to compensate for angular misalignment. MSTS = Maximum Static Tensile Strength. MSAS = Maximum Static Axial Compressive Strength.

There is also a good range of Joints - Dual Eye - Parallel on the Small Parts and Bearings website.


Pins - Dowel - Extractable
Pins - Dowel - Extractable

Also see combined categories:
All Dowel Pins

Hardened and Ground Steel 100 Cr6. Din 7979.

Extractable dowels have a thread tapped in the end to fascilitate removal from blind holes. An air release flat is ground along the full length of the pin to overcome the problem of pressure build up by trapped air. Hardness 55-62 HRC, HV550-650. Extractable pins may or may not have a flat to vent pressure when pulling. Also known as parallel pins.

Related Information:

There is also a good range of Pins - Dowel - Extractable on the Small Parts and Bearings website.


Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends
Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - DIN7

Diameter tolerances are m6. Also known as parallel pins.

Related Information:

There is also a good range of Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends on the Small Parts and Bearings website.


Housings - Linear - Square
Housings - Linear - Square

Also see combined categories:
All Linear Bearing Housings

Used to maintain radial integrity and eliminate the need for parallel shafting.

Bearings are made from 6061-T6 Aluminum with Anodized finished. Equipped with bearing plugs that run on a single shaft. Threaded adjustable plugs are made from 316 Stainless with self-lubricating FrelonJ wear pads.

There is also a good range of Housings - Linear - Square on the Small Parts and Bearings website.


Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends
Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 316 Grade - DIN7

Diameter tolerances are m6. Also known as parallel pins.

Related Information:

There is also a good range of Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends on the Small Parts and Bearings website.


Couplings - Helical - Long Series
Couplings - Helical - Long Series

Also see combined categories:
All Helical and Slit Couplings

2.9 to 31.4 Nm.

5o max angular misalignment. 0.762 mm Parallel offset. +/- 0.254 mm Axial motion. Zero backlash.

Related Information:

There is also a good range of Couplings - Helical - Long Series on the Small Parts and Bearings website.


Couplings - Helical - Low Inertia
Couplings - Helical - Low Inertia

Also see combined categories:
All Helical and Slit Couplings

0.8 to 13.2 Nm.

5o max angular misalignment. 0.254 mm Parallel offset. +/- 0.203 mm Axial motion. Zero backlash.

Related Information:

There is also a good range of Couplings - Helical - Low Inertia on the Small Parts and Bearings website.


Couplings - Helical - Standard
Couplings - Helical - Standard

Also see combined categories:
All Helical and Slit Couplings

0.1 to 16.2 Nm.

Zero backlash. Max. Ang Misalignment 5o. Max Parallel Offset 0.25mm.

Related Information:

There is also a good range of Couplings - Helical - Standard on the Small Parts and Bearings website.


Couplings - Helical - Precision
Couplings - Helical - Precision

Also see combined categories:
All Helical and Slit Couplings

0.14 to 9 Nm. 25000 max RPM.

5o max angular misalignment. 0.076 mm Parallel offset. Zero Axial motion. Zero backlash.

Related Information:

There is also a good range of Couplings - Helical - Precision on the Small Parts and Bearings website.


Pins - Dowel - Standard - Chamfered End
Pins - Dowel - Standard - Chamfered End

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - DIN6325, ISO2338

Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.

Related Information:

There is also a good range of Pins - Dowel - Standard - Chamfered End on the Small Parts and Bearings website.


Couplings - Crowned Tooth Gear - Hubs Only
Couplings - Crowned Tooth Gear - Hubs Only


Match with sleeves from the sleeves category

+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.

Related Information:

There is also a good range of Couplings - Crowned Tooth Gear - Hubs Only on the Small Parts and Bearings website.


Couplings - Crowned Tooth Gear - Sleeve Only
Couplings - Crowned Tooth Gear - Sleeve Only


Match with hubs from the hubs category

+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.

Related Information:

There is also a good range of Couplings - Crowned Tooth Gear - Sleeve Only on the Small Parts and Bearings website.


Couplings - Helical - Economy
Couplings - Helical - Economy

Also see combined categories:
All Helical and Slit Couplings

Low cost aluminium couplings primarily used for 3D printer stepper motors

Max. Ang Misalignment 5o. Max Parallel Offset 0.25mm.

Related Information:

There is also a good range of Couplings - Helical - Economy on the Small Parts and Bearings website.


Couplings - Spline Type - Complete
Couplings - Spline Type - Complete

Also see combined categories:
All Insert and Jaw Type Couplings

0.5 to 4.5 Nm. 12000 to 24000 rpm.

Maximum parallel offset 0.2mm, Maximum working angle 2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 oC.

Related Information:

There is also a good range of Couplings - Spline Type - Complete on the Small Parts and Bearings website.


Couplings - Spline Type - Spare Hubs
Couplings - Spline Type - Spare Hubs

Also see combined categories:
All Insert and Jaw Type Couplings

0.5 to 4.5 Nm. 12000 to 24000 rpm.

Maximum parallel offset 0.2mm, Maximum working angle 2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 oC.

Related Information:

There is also a good range of Couplings - Spline Type - Spare Hubs on the Small Parts and Bearings website.


Pins - Dowel - Standard - 316 Stainless - Chamfered End
Pins - Dowel - Standard - 316 Stainless - Chamfered End

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 316 Grade - DIN6325, ISO2338

Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.

Related Information:

There is also a good range of Pins - Dowel - Standard - 316 Stainless - Chamfered End on the Small Parts and Bearings website.


Pins - Dowel - Standard - 416 Stainless - Chamfered End
Pins - Dowel - Standard - 416 Stainless - Chamfered End

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 416 Grade - DIN6325, ISO2338

Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.

Related Information:

There is also a good range of Pins - Dowel - Standard - 416 Stainless - Chamfered End on the Small Parts and Bearings website.


Couplings - Spline Type - Spare Poyurethane Splines
Couplings - Spline Type - Spare Poyurethane Splines

Also see combined categories:
All Insert and Jaw Type Couplings

0.5 to 4.5 Nm. 12000 to 24000 rpm.

Maximum parallel offset 0.2mm, Maximum working angle 2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 oC.

Related Information:

There is also a good range of Couplings - Spline Type - Spare Poyurethane Splines on the Small Parts and Bearings website.


Pins - Dowel - Standard - 303-304 Stainless - Chamfered End
Pins - Dowel - Standard - 303-304 Stainless - Chamfered End

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 303/304 Grade Stainless - DIN6325, ISO2338

Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.

Related Information:

There is also a good range of Pins - Dowel - Standard - 303-304 Stainless - Chamfered End on the Small Parts and Bearings website.


Slides - Dovetail
Slides - Dovetail

Also see combined categories:
All Linear Slides

Used for work feeders for production milling, positioning fixutres, work holding devices, checking fixtures, shuttle devices, assembly equipment, etc.

Tapered gibs are adjusted with a single screw that moves the gib on the taper. This type remains parallel and wears less as it occurs over the entire surface. Made of continuous cast GS 40,000 PSI pearlitic grey iron. Able to be milled, drilled, tapped, etc.

There is also a good range of Slides - Dovetail on the Small Parts and Bearings website.


Couplings - Spider Type B - Complete
Couplings - Spider Type B - Complete

Also see combined categories:
All Insert and Jaw Type Couplings

Max 3600 RPM. 0.39 to 16.27 Nm. Match only hubs and spiders from listings SPIDER TYPE B. Insert is set between the jaws of two hubs.

Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM. Rubber spider and metal hubs.

Related Information:

There is also a good range of Couplings - Spider Type B - Complete on the Small Parts and Bearings website.


Couplings - Spider Type B - Hubs Only
Couplings - Spider Type B - Hubs Only


Match 2 hubs with a spider from the spiders category. Match only rubber spiders from listings SPIDER TYPE B. Insert is set between the jaws of two hubs.

Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM. Metal hubs to suit rubber spiders type B.

Related Information:

There is also a good range of Couplings - Spider Type B - Hubs Only on the Small Parts and Bearings website.


Pins - Dowel - Extractable - With Vent
Pins - Dowel - Extractable - With Vent

Also see combined categories:
All Dowel Pins

Hardened and Ground Steel 100 Cr6 with a ground flat along one edge

Extractable dowels have a thread tapped in the end to fascilitate removal from blind holes. An air release flat is ground along the full length of the pin. Hardness 55-62 HRC, HV550-650. Also known as parallel pins.

Related Information:

There is also a good range of Pins - Dowel - Extractable - With Vent on the Small Parts and Bearings website.


Pins - Dowel - Standard - 303-304 Stainless - Rounded Both Ends
Pins - Dowel - Standard - 303-304 Stainless - Rounded Both Ends

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 303/304 Grade Stainless- DIN7

Rounded end dowel pins are measured from the start of the edge rounding. This allows the pin to completely fill the hole after you grind off the rounded end. Diameter tolerances are m6. Also known as parallel pins.

Related Information:

There is also a good range of Pins - Dowel - Standard - 303-304 Stainless - Rounded Both Ends on the Small Parts and Bearings website.


Slides - Linear - Cross Roller Rail
Slides - Linear - Cross Roller Rail

Also see combined categories:
All Linear Slides

Compact, precision bearings that can support and guide high loads with high accuracy and repeatability, low friction, and low starting force.

Each consists of a pair of hardened steel ways containing 90 deg V grooves and a row of alternately crossed cylindrical rollers. Installed faced to face on smooth flat and accurately parallel, coplanar or perpendicular surfaces. Lubrication required, light grease for low speeds to continuous oil bath/mist for high speeds.

There is also a good range of Slides - Linear - Cross Roller Rail on the Small Parts and Bearings website.


Tensioner - Heavy Duty - Type 4
Tensioner - Heavy Duty - Type 4

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Has 152.4mm travel through the use of the adjusting slots. Head is drilled and tapped to accept 50.8mm diameter idler shaft (ordered separately).

Idler shaft and pulleys not included with tensioner. Shaft is mounted straight out from face and anchored by set screws. Adjusting slots are parallel to each other.

Related Information:

There is also a good range of Tensioner - Heavy Duty - Type 4 on the Small Parts and Bearings website.


Couplings - Oldham - Complete - Acetal Disk - Set Screw
Couplings - Oldham - Complete - Acetal Disk - Set Screw

Also see combined categories:
All Insert and Jaw Type Couplings

0.06 to 44 Nm. Max Speed: 3000 RPM.

Max Speed: 3000 RPM. Parallel out of line compensation. Temp Range -20 oC to +60 oC. Oldham couplings are designed to transfer torque between two parallel, but not colinear, shafts. They have three discs, one coupled to the input, one coupled to the output, and a centre disc that is joined to the first two by tongue and grooves. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.

Related Information:

There is also a good range of Couplings - Oldham - Complete - Acetal Disk - Set Screw on the Small Parts and Bearings website.


Balls - Ceramic - Ruby - Synthetic
Balls - Ceramic - Ruby - Synthetic

Also see combined categories:
All Ceramic Balls
All Non Metallic Balls

Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.

Tolerances available on request. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Specific Gravity: 3.98.

Related Information:

There is also a good range of Balls - Ceramic - Ruby - Synthetic on the Small Parts and Bearings website.


Balls - Ceramic - Sapphire - Synthetic
Balls - Ceramic - Sapphire - Synthetic

Also see combined categories:
All Ceramic Balls
All Non Metallic Balls

Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.

Tolerances available on request. Specific Gravity: 3.98. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Transparent (refractive index 1.76).

Related Information:

There is also a good range of Balls - Ceramic - Sapphire - Synthetic on the Small Parts and Bearings website.


Balls - Ceramic - Silicon Nitride
Balls - Ceramic - Silicon Nitride

Also see combined categories:
All Ceramic Balls
All Non Metallic Balls

Outstanding wear resistance. Good thermal and chemical resistance.

High hardness. High strength over a wide temperature range. High fracture toughness. Outstanding wear resistance. Good thermal and chemical resistance.

Related Information:

There is also a good range of Balls - Ceramic - Silicon Nitride on the Small Parts and Bearings website.


Balls - Ceramic - Zirconia
Balls - Ceramic - Zirconia

Also see combined categories:
All Ceramic Balls
All Non Metallic Balls

Outstanding wear resistance. Excellent thermal and chemical resistance.


Related Information:

There is also a good range of Balls - Ceramic - Zirconia on the Small Parts and Bearings website.


Balls - Chrome Steel
Balls - Chrome Steel

Also see combined categories:
All Metallic Balls

Hardness: Rockwell C: 60-70.

Tolerances available on request. SAE 52100 Chrome Steel. Hardness: Rockwell C: 60-70. Specific Gravity: 7.833.

Related Information:

There is also a good range of Balls - Chrome Steel on the Small Parts and Bearings website.


Balls - Phosphor Bronze
Balls - Phosphor Bronze

Also see combined categories:
All Metallic Balls

Specific Gravity 8.4


Related Information:

There is also a good range of Balls - Phosphor Bronze on the Small Parts and Bearings website.


Balls - Stainless Steel - 304 Grade
Balls - Stainless Steel - 304 Grade

Also see combined categories:
All Metallic Balls

A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.

Tolerances available on request. Grade 100. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000 oC.

Related Information:

There is also a good range of Balls - Stainless Steel - 304 Grade on the Small Parts and Bearings website.


Balls - Stainless Steel - 316 Grade
Balls - Stainless Steel - 316 Grade

Also see combined categories:
All Metallic Balls

A4 Grade. Very low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.

Tolerances available on request. Grade 100. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000 oC.

Related Information:

There is also a good range of Balls - Stainless Steel - 316 Grade on the Small Parts and Bearings website.


Balls - Stainless Steel - 316L Grade
Balls - Stainless Steel - 316L Grade

Also see combined categories:
All Metallic Balls

Easier to machine than standard 316 grade.

316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.

Related Information:

There is also a good range of Balls - Stainless Steel - 316L Grade on the Small Parts and Bearings website.


Balls - Stainless Steel - 440C Grade
Balls - Stainless Steel - 440C Grade

Also see combined categories:
All Metallic Balls

Hardness: Rockwell C: 55-60.

Tolerances available on request. AISI440C Stainless Steel.

Related Information:

There is also a good range of Balls - Stainless Steel - 440C Grade on the Small Parts and Bearings website.


Balls - Steel - Bored
Balls - Steel - Bored

Also see combined categories:
All Metallic Balls - Bored

Bored steel balls as used in steel rod ends.

Hardness: 58-64 Rc. Material: SUJ-2.

Related Information:

There is also a good range of Balls - Steel - Bored on the Small Parts and Bearings website.


Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI
Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI

Also see combined categories:
All Metallic Balls

Implant Grade can be used for Jewellery and Body Piercing. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.

Precision Grade: 200. Plain. Composition Percentage: Al 5.5-6.5, V 3.5-4.5, N 0.03, C 0.08, H 0.013, Fe 0.25, O 0.13, Ti Balance. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.

Related Information:

There is also a good range of Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI on the Small Parts and Bearings website.


Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI - Threaded
Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI - Threaded

Also see combined categories:
All Threaded Metallic Balls

Implant Grade can be used for Jewellery and Body Piercing. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.

Precision Grade: 200. Plain. Composition Percentage: Al 5.5-6.5, V 3.5-4.5, N 0.03, C 0.08, H 0.013, Fe 0.25, O 0.13, Ti Balance. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent. Threaded either 1-72 UNF or M1.2.

Related Information:

There is also a good range of Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI - Threaded on the Small Parts and Bearings website.


Balls - Tungsten Carbide
Balls - Tungsten Carbide

Also see combined categories:
All Metallic Balls

Extreme hardness and wear resistance.

Tolerances available on request. Precision Grade: Grade 25. Hardness: Rockwell A: 91.5 (Approx 77 Rockwell C). Extreme hardness and wear resistance. Specific Gravity: 14.95.

Related Information:

There is also a good range of Balls - Tungsten Carbide on the Small Parts and Bearings website.


Balls - Plastic - Acetal
Balls - Plastic - Acetal

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

High intensity strength, rigidity, outstanding resistance to abrasion and most solvents.

Tolerances available on request. Acetal Copolymer. High intensity strength, rigidity, outstanding resistance to abrasion and most solvents. Opaque White. Specific Gravity: 1.4.

Related Information:

There is also a good range of Balls - Plastic - Acetal on the Small Parts and Bearings website.


Balls - Plastic - Acrylic
Balls - Plastic - Acrylic

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

Resistance to weather and sunlight. Good abrasion resistance.

Diametrical tolerances typically +/- 0.08 or 0.13 mm depending on size. Acrylic (Methyl Methacrylate). Resistance to weather and sunlight. Good abrasion resistance. Water clear transparent. Polished. Ground and Polished.

Related Information:

There is also a good range of Balls - Plastic - Acrylic on the Small Parts and Bearings website.


Balls - Plastic - Bored
Balls - Plastic - Bored

Also see combined categories:
All Plastic Balls - Bored

Bored acetal balls as used in plastic rod ends.

Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight.

Related Information:

There is also a good range of Balls - Plastic - Bored on the Small Parts and Bearings website.


Balls - Plastic - Nylon
Balls - Plastic - Nylon

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

Resists alkalies, weak acids and most organic solvents.

Tolerances available on request. Nylon (Polyamide 6/6). Resists alkalies, weak acids and most organic solvents. Low water absorption. Unpolished. Specific Gravity: 1.14.

Related Information:

There is also a good range of Balls - Plastic - Nylon on the Small Parts and Bearings website.


Balls - Plastic - Polypropylene
Balls - Plastic - Polypropylene

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

Excellent for liquid level float applications.

Tolerance and spherecity: up to and including 25.4mm diameter = +/-0.0508mm, over 25.4mm diameter +/-0.0762mm. Very resistant to most acids and alkalies. Excellent for liquid level float applications. Unpolished. Specific Gravity: 0.91.

Related Information:

There is also a good range of Balls - Plastic - Polypropylene on the Small Parts and Bearings website.


Balls - Plastic - PTFE
Balls - Plastic -  PTFE

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

No water absorption. Temperatures up to 288 Deg C.

Tolerances available on request. Not affected by any known acids or alkalies. No water absorption. Temperatures up to 288 oC. Unpolished. Specific Gravity: 2.3.

Related Information:

There is also a good range of Balls - Plastic - PTFE on the Small Parts and Bearings website.


Balls - Plastic - PVC
Balls - Plastic -  PVC

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

Polyvinyl chloride. PVC is a chemically stable material, which shows little change in molecular structure, and also exhibits little change in its mechanical strength.

Polyvinyl chloride is a widely used and inexpensive thermoplastic polymer. It is easily worked or machined and has good chemical and biological resistance. It is relatively hard and can be polished to a shine. Polyvinyl chloride is a widely used and inexpensive thermoplastic polymer. Heat Deflection Temperature 176 F / 80 C. Rockwell Hardness 115. Zero water absorption in 24 hours.

Related Information:

There is also a good range of Balls - Plastic - PVC on the Small Parts and Bearings website.


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 122528 products in 2632 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 122528 products in 2632 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.