Ball Parallels Categories
Parallels - Ball
Used for handling large work in drill presses or band saw machines.
Placed between work and machine so work can be easily moved. Black Oxide finish with 9.525mm hardened steel balls. Balls are exposed both sides of sheet.
There is also a good range of Parallels - Ball on the Small Parts and Bearings website.
You may also be interested in
Bearings Double Row Ball
Bearings - Ball - Double Row - Self Aligning - Parallel Bore
Related Information:
There is also a good range of Bearings - Ball - Double Row - Self Aligning - Parallel Bore on the Small Parts and Bearings website.
Pins - Dowel - Extractable
Hardened and Ground Steel 100 Cr6. Din 7979.
Extractable dowels have a thread tapped in the end to fascilitate removal from blind holes. An air release flat is ground along the full length of the pin to overcome the problem of pressure build up by trapped air. Hardness 55-62 HRC, HV550-650. Extractable pins may or may not have a flat to vent pressure when pulling. Also known as parallel pins.
Related Information:
There is also a good range of Pins - Dowel - Extractable on the Small Parts and Bearings website.
Housings - Linear - Square
Used to maintain radial integrity and eliminate the need for parallel shafting.
Bearings are made from 6061-T6 Aluminum with Anodized finished. Equipped with bearing plugs that run on a single shaft. Threaded adjustable plugs are made from 316 Stainless with self-lubricating FrelonJ wear pads.
There is also a good range of Housings - Linear - Square on the Small Parts and Bearings website.
Pins - Dowel - Standard - 416 Stainless - Chamfered End
Precision Dowel Pins - 416 Grade - Based on DIN6325 or ISO2338
Also known as parallel pins. Also known as parallel pins.
Related Information:
There is also a good range of Pins - Dowel - Standard - 416 Stainless - Chamfered End on the Small Parts and Bearings website.
Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends
Precision Dowel Pins - Based on DIN7
Diameter tolerances are m6. Also known as parallel pins.
Related Information:
There is also a good range of Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends on the Small Parts and Bearings website.
Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends
Precision Dowel Pins - 316 Grade - Based on DIN7
Diameter tolerances are m6. Also known as parallel pins.
Related Information:
There is also a good range of Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends on the Small Parts and Bearings website.
Couplings - Helical - Standard
0.1 to 16.2 Nm.
Zero backlash. Max. Ang Misalignment 5o. Max Parallel Offset 0.25mm.
Related Information:
There is also a good range of Couplings - Helical - Standard on the Small Parts and Bearings website.
Couplings - Crowned Tooth Gear - Hubs Only
Match with sleeves from the sleeves category
+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.
Related Information:
There is also a good range of Couplings - Crowned Tooth Gear - Hubs Only on the Small Parts and Bearings website.
Couplings - Crowned Tooth Gear - Sleeve Only
Match with hubs from the hubs category
+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.
Related Information:
There is also a good range of Couplings - Crowned Tooth Gear - Sleeve Only on the Small Parts and Bearings website.
Pins - Dowel - Standard - Chamfered End
Precision Dowel Pins - Based on DIN6325, ISO2338
Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.
Related Information:
There is also a good range of Pins - Dowel - Standard - Chamfered End on the Small Parts and Bearings website.
Couplings - Helical - Economy
Low cost aluminium couplings primarily used for 3D printer stepper motors
Max. Ang Misalignment 5o. Max Parallel Offset 0.25mm.
Related Information:
There is also a good range of Couplings - Helical - Economy on the Small Parts and Bearings website.
Couplings - Spline Type - Complete
0.5 to 4.5 Nm. 12000 to 24000 rpm.
Maximum parallel offset 0.2mm, Maximum working angle 2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 oC.
Related Information:
There is also a good range of Couplings - Spline Type - Complete on the Small Parts and Bearings website.
Couplings - Spline Type - Spare Hubs
0.5 to 4.5 Nm. 12000 to 24000 rpm.
Maximum parallel offset 0.2mm, Maximum working angle 2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 oC.
Related Information:
There is also a good range of Couplings - Spline Type - Spare Hubs on the Small Parts and Bearings website.
Couplings - Spline Type - Spare Poyurethane Splines
0.5 to 4.5 Nm. 12000 to 24000 rpm.
Maximum parallel offset 0.2mm, Maximum working angle 2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 oC.
Related Information:
There is also a good range of Couplings - Spline Type - Spare Poyurethane Splines on the Small Parts and Bearings website.
Pins - Dowel - Standard - 316 Stainless - Chamfered End
Precision Dowel Pins - 316 Grade - Based on DIN6325, ISO2338, ISO 8734
Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.
Related Information:
There is also a good range of Pins - Dowel - Standard - 316 Stainless - Chamfered End on the Small Parts and Bearings website.
Pins - Dowel - Standard - 303-304 Stainless - Chamfered End
Precision Dowel Pins - 303/304 Grade Stainless - Based on DIN6325, ISO2338, ISO 8734
Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.
Related Information:
There is also a good range of Pins - Dowel - Standard - 303-304 Stainless - Chamfered End on the Small Parts and Bearings website.
Slides - Dovetail
Used for work feeders for production milling, positioning fixutres, work holding devices, checking fixtures, shuttle devices, assembly equipment, etc.
Tapered gibs are adjusted with a single screw that moves the gib on the taper. This type remains parallel and wears less as it occurs over the entire surface. Made of continuous cast GS 40,000 PSI pearlitic grey iron. Able to be milled, drilled, tapped, etc.
There is also a good range of Slides - Dovetail on the Small Parts and Bearings website.
Couplings - Spider Type B - Hubs Only
Match 2 hubs with a spider from the spiders category. Match only rubber spiders from listings SPIDER TYPE B. Insert is set between the jaws of two hubs.
Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM. Metal hubs to suit rubber spiders type B.
Related Information:
There is also a good range of Couplings - Spider Type B - Hubs Only on the Small Parts and Bearings website.
Pins - Dowel - Extractable - With Vent
Hardened and Ground Steel 100 Cr6 with a ground flat along one edge. DIN7979D.
Extractable dowels have a thread tapped in the end to fascilitate removal from blind holes. An air release flat is ground along the full length of the pin. Hardness 55-62 HRC, HV550-650. Also known as parallel pins.
Related Information:
There is also a good range of Pins - Dowel - Extractable - With Vent on the Small Parts and Bearings website.
Pins - Dowel - Standard - 303-304 Stainless - Rounded Both Ends
Precision Dowel Pins - 303/304 Grade Stainless- Based on DIN7
Rounded end dowel pins are measured from the start of the edge rounding. This allows the pin to completely fill the hole after you grind off the rounded end. Diameter tolerances are m6. Also known as parallel pins.
Related Information:
There is also a good range of Pins - Dowel - Standard - 303-304 Stainless - Rounded Both Ends on the Small Parts and Bearings website.
Slides - Linear - Cross Roller Rail
Compact, precision bearings that can support and guide high loads with high accuracy and repeatability, low friction, and low starting force.
Each consists of a pair of hardened steel ways containing 90 deg V grooves and a row of alternately crossed cylindrical rollers. Installed faced to face on smooth flat and accurately parallel, coplanar or perpendicular surfaces. Lubrication required, light grease for low speeds to continuous oil bath/mist for high speeds.
There is also a good range of Slides - Linear - Cross Roller Rail on the Small Parts and Bearings website.
Tensioner - Heavy Duty - Type 4
Use with idler shafts and idler pulleys. Has 152.4mm travel through the use of the adjusting slots. Head is drilled and tapped to accept 50.8mm diameter idler shaft (ordered separately).
Idler shaft and pulleys not included with tensioner. Shaft is mounted straight out from face and anchored by set screws. Adjusting slots are parallel to each other.
Related Information:
There is also a good range of Tensioner - Heavy Duty - Type 4 on the Small Parts and Bearings website.
Balls - Ceramic - Ruby - Synthetic
Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Specific Gravity: 3.98.
Related Information:
There is also a good range of Balls - Ceramic - Ruby - Synthetic on the Small Parts and Bearings website.
Balls - Ceramic - Sapphire - Synthetic
Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Specific Gravity: 3.98. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Transparent (refractive index 1.76).
Related Information:
There is also a good range of Balls - Ceramic - Sapphire - Synthetic on the Small Parts and Bearings website.
Balls - Ceramic - Silicon Nitride
Outstanding wear resistance. Good thermal and chemical resistance.
High hardness. Grades shown are AFBMA / ISO3290-1. High strength over a wide temperature range. High fracture toughness. Outstanding wear resistance. Good thermal and chemical resistance.
Related Information:
There is also a good range of Balls - Ceramic - Silicon Nitride on the Small Parts and Bearings website.
Balls - Ceramic - Zirconia
Outstanding wear resistance. Excellent thermal and chemical resistance.
Grades shown are AFBMA / ISO3290-1.
Related Information:
There is also a good range of Balls - Ceramic - Zirconia on the Small Parts and Bearings website.
Balls - Chrome Steel
Hardness: Rockwell C: 60-70.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. SAE 52100 Chrome Steel. Hardness: Rockwell C: 60-70. Specific Gravity: 7.833.
Related Information:
There is also a good range of Balls - Chrome Steel on the Small Parts and Bearings website.
Balls - Phosphor Bronze
Specific Gravity 8.4
Grades shown are AFBMA / ISO3290-1.
Related Information:
There is also a good range of Balls - Phosphor Bronze on the Small Parts and Bearings website.
Balls - Stainless Steel - 304 Grade
A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000 oC.
Related Information:
There is also a good range of Balls - Stainless Steel - 304 Grade on the Small Parts and Bearings website.
Balls - Stainless Steel - 316 Grade
A4 Grade. Very low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000 oC.
Related Information:
There is also a good range of Balls - Stainless Steel - 316 Grade on the Small Parts and Bearings website.
Balls - Stainless Steel - 316L Grade
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.
Related Information:
There is also a good range of Balls - Stainless Steel - 316L Grade on the Small Parts and Bearings website.
Balls - Stainless Steel - 400 Grade
Hardness: Rockwell C: 55-60. Includes 420 and 440C grades
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. AISI440C Stainless Steel.
Related Information:
There is also a good range of Balls - Stainless Steel - 400 Grade on the Small Parts and Bearings website.
Balls - Steel - Bored
Bored steel balls as used in steel rod ends.
Hardness: 58-64 Rc. Material: SUJ-2.
Related Information:
There is also a good range of Balls - Steel - Bored on the Small Parts and Bearings website.
Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI
Implant Grade can be used for Jewellery and Body Piercing. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.
Precision Grade: 200. Grades shown are AFBMA / ISO3290-1. Plain. Composition Percentage: Al 5.5-6.5, V 3.5-4.5, N 0.03, C 0.08, H 0.013, Fe 0.25, O 0.13, Ti Balance. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.
Related Information:
There is also a good range of Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI on the Small Parts and Bearings website.
Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI - Threaded
Implant Grade can be used for Jewellery and Body Piercing. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.
Precision Grade: 200. Grades shown are AFBMA / ISO3290-1. Plain. Composition Percentage: Al 5.5-6.5, V 3.5-4.5, N 0.03, C 0.08, H 0.013, Fe 0.25, O 0.13, Ti Balance. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent. Threaded either 1-72 UNF or M1.2.
Related Information:
There is also a good range of Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI - Threaded on the Small Parts and Bearings website.
Balls - Tungsten Carbide
Extreme hardness and wear resistance.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Precision Grade: Grade 25. Hardness: Rockwell A: 91.5 (Approx 77 Rockwell C). Extreme hardness and wear resistance. Specific Gravity: 14.95.
Related Information:
There is also a good range of Balls - Tungsten Carbide on the Small Parts and Bearings website.
Balls - Plastic - Acetal
High intensity strength, rigidity, outstanding resistance to abrasion and most solvents.
Tolerances available on request. Acetal Copolymer. High intensity strength, rigidity, outstanding resistance to abrasion and most solvents. Standard Opaque White. Specific Gravity: 1.4.
Related Information:
There is also a good range of Balls - Plastic - Acetal on the Small Parts and Bearings website.
Balls - Plastic - Acrylic
Resistance to weather and sunlight. Good abrasion resistance.
Diametrical tolerances typically + / - 0.08 or 0.13 mm depending on size. Acrylic (Methyl Methacrylate). Resistance to weather and sunlight. Good abrasion resistance. Water clear transparent. Polished. Ground and Polished.
Related Information:
There is also a good range of Balls - Plastic - Acrylic on the Small Parts and Bearings website.
Balls - Plastic - Bored
Bored acetal balls as used in plastic rod ends.
Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight.
Related Information:
There is also a good range of Balls - Plastic - Bored on the Small Parts and Bearings website.
Balls - Plastic - Nylon
Resists alkalies, weak acids and most organic solvents.
Tolerances available on request. Nylon (Polyamide 6/6). Resists alkalies, weak acids and most organic solvents. Low water absorption. Unpolished. Specific Gravity: 1.14.
Related Information:
There is also a good range of Balls - Plastic - Nylon on the Small Parts and Bearings website.
Balls - Plastic - Polypropylene
Excellent for liquid level float applications.
Tolerance and sphericity: up to and including 25.4mm diameter = + / -0.0508mm, over 25.4mm diameter +/-0.0762mm. Very resistant to most acids and alkalies. Excellent for liquid level float applications. Unpolished. Specific Gravity: 0.91.
Related Information:
There is also a good range of Balls - Plastic - Polypropylene on the Small Parts and Bearings website.
Balls - Plastic - PTFE
No water absorption. Temperatures up to 288 Deg C.
Tolerances available on request. Not affected by any known acids or alkalies. No water absorption. Temperatures up to 288 oC. Unpolished. Specific Gravity: 2.3.
Related Information:
There is also a good range of Balls - Plastic - PTFE on the Small Parts and Bearings website.
Balls - Plastic - PVC
Polyvinyl chloride. PVC is a chemically stable material, which shows little change in molecular structure, and also exhibits little change in its mechanical strength.
Polyvinyl chloride is a widely used and inexpensive thermoplastic polymer. It is easily worked or machined and has good chemical and biological resistance. It is relatively hard and can be polished to a shine. Polyvinyl chloride is a widely used and inexpensive thermoplastic polymer. Heat Deflection Temperature 176 F / 80 C. Rockwell Hardness 115. Zero water absorption in 24 hours.
Related Information:
There is also a good range of Balls - Plastic - PVC on the Small Parts and Bearings website.
Balls - Plastic - Torlon
TorlonTM 4301 Bearing Grade Balls. Grade 1.
Polyamide-imide (TorlonTM< / sup>) Balls. Rockwell Hardness (Method A): E86 or M109-119. Specific Gravity: 1.38. Colour: Brown Opaque.
Related Information:
There is also a good range of Balls - Plastic - Torlon on the Small Parts and Bearings website.
Balls - Rubber - Santoprene 40D
A high performance thermoplastic created by cross linking EPDM rubber with Polypropylene. As an elastomer plastic it is flexible, light weight, and has very good abrasion resistance. It also has good resistance to many acids, bases and aqueous solutions.
It holds up well in both extreme hot and cold environments which can make it preferred over rubber. Common uses include; grips, knobs, handles, gaskets, and ball check valves. Specific Gravity .95 g/cc. Hardness, Shore 40D. Tensile Strength 3000 psi. Melting Point 410 F. Rohs Compliant. Not FDA compliant. This grade is slightly harder than the 87A grade. Colour usually red but some sizes are beige.
Related Information:
There is also a good range of Balls - Rubber - Santoprene 40D on the Small Parts and Bearings website.
Balls - Rubber - Santoprene 87A
A high performance thermoplastic created by cross linking EPDM rubber with Polypropylene. As an elastomer plastic it is flexible, light weight, and has very good abrasion resistance. It also has good resistance to many acids, bases and aqueous solutions.
It holds up well in both extreme hot and cold environments which can make it preferred over rubber. Common uses include; grips, knobs, handles, gaskets, and ball check valves. Specific Gravity .96 g/cc. Hardness, Shore 87A. Tensile Strength 2550 psi. Melting Point 400 F. Rohs Compliant and FDA compliant. This grade is slightly softer than the 40D grade. Colour Beige.
Related Information:
There is also a good range of Balls - Rubber - Santoprene 87A on the Small Parts and Bearings website.
Ball Transfer Units - Base Mount - Heavy Duty - Steel
Single ball bearings units for conveyor systems
There is also a good range of Ball Transfer Units - Base Mount - Heavy Duty - Steel on the Small Parts and Bearings website.
Ball Transfer Units - Dismantlable - Heavy Duty - Steel
Single ball bearings units for conveyor systems
There is also a good range of Ball Transfer Units - Dismantlable - Heavy Duty - Steel on the Small Parts and Bearings website.
Ball Transfer Units - Flange Mount - Heavy Duty - Pressed Steel
Single ball bearings units for conveyor systems
There is also a good range of Ball Transfer Units - Flange Mount - Heavy Duty - Pressed Steel on the Small Parts and Bearings website.
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Contact Us
Charity
Dental Bearings
Distributor Locations
Dowel Pins
Downloadable PDF Catalogue Ball Lock Pins
Downloadable PDF Catalogue Balls
Downloadable PDF Catalogue Ceramic Bearings
Downloadable PDF Catalogue Circlips
Downloadable PDF Catalogue Clevis Pins
Downloadable PDF Catalogue Corrosion Resistant Bearings
Downloadable PDF Catalogue Disc Springs
Downloadable PDF Catalogue Dowel Pins
Downloadable PDF Catalogue Economy Bearings
Downloadable PDF Catalogue Hammer Drive Pins
Downloadable PDF Catalogue High Speed Bearings
Downloadable PDF Catalogue Key Steel
Downloadable PDF Catalogue Knobs
Downloadable PDF Catalogue Leveling Mounts
Downloadable PDF Catalogue Metallic Bushes
Downloadable PDF Catalogue O-Rings
Downloadable PDF Catalogue Pins
Downloadable PDF Catalogue Plastic Bearings
Downloadable PDF Catalogue Polyvee Belts and Pulleys
Downloadable PDF Catalogue Precision Shim Washers
Downloadable PDF Catalogue Push On and Push In Rings
Downloadable PDF Catalogue Rod & Tube
Downloadable PDF Catalogue Roll Pins
Downloadable PDF Catalogue Shaft Collars
Downloadable PDF Catalogue Shim Sheet
Downloadable PDF Catalogue Shoulder Screws
Downloadable PDF Catalogue Sintered Bronze Bushes
Downloadable PDF Catalogue Snap Rings
Downloadable PDF Catalogue Socket Set Screws
Downloadable PDF Catalogue Solid Bronze Bushes
Downloadable PDF Catalogue Spring Steel Strip
Downloadable PDF Catalogue Springs
Downloadable PDF Catalogue Standard Ball Bearing Range
Downloadable PDF Catalogue Super Precision Bearings
Downloadable PDF Catalogue Taper Pins
Downloadable PDF Catalogue Thrust Bearings
Downloadable PDF Catalogue Thumb Screws and Nuts
Downloadable PDF Catalogue Timing Belts
Downloadable PDF Catalogue Timing Pulley Stock
Downloadable PDF Catalogue Timing Pulleys
Downloadable PDF Catalogue Vibration Mounts
Downloadable PDF Catalogue Washers
Downloadable PDF Catalogue Wave Washers
Downloadable PDF Cross Reference ADR and SKF
Downloadable PDF Cross Reference Anderton Circlips
Downloadable PDF Cross Reference Barden Bearings
Downloadable PDF Cross Reference Essentra
Downloadable PDF Cross Reference Flocast
Downloadable PDF Cross Reference K&S Metals
Downloadable PDF Cross Reference McMaster Carr
Downloadable PDF Cross Reference Miniature Precison Bearings
Downloadable PDF Cross Reference Nordex
Downloadable PDF Cross Reference NSK and NTN
Downloadable PDF Cross Reference Ondrives
Downloadable PDF Cross Reference Reid Supply
Downloadable PDF Cross Reference SDP-SI Designatronics
Downloadable PDF Cross Reference Seeger Circlips
Downloadable PDF Cross Reference Sintered Bronze
Downloadable PDF Cross Reference Small Parts Inc
Downloadable PDF Cross Reference Timing Belts and Pulleys
Freight Rates and Shipping Times
Frequently Asked Questions
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Satellite Reaction Wheels
Shipping Rates and Times
Technical
Terms
5 Axis Machine Tool Bearings
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)
Miniature Bearings Australia offers 130510 products in 2127 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.
