Miniature Bearings Australia Pty Ltd

Inserts Thread Repair Helicoil Installation Tools Categories


Thread Inserts


Inserts - Thread Repair - Helicoil Installation Tools
Inserts - Thread Repair - Helicoil Installation Tools

Tools for helicoil inserts include economy style and production style prewinder and threaded mandrel types


There is also a good range of Inserts - Thread Repair - Helicoil Installation Tools on the Small Parts and Bearings website.


Inserts - Thread Repair - Helicoil Starter Sets
Inserts - Thread Repair - Helicoil Starter Sets

Also see combined categories:
All Helicoil Inserts and Kits

Helicoil sets include 3 lengths of 1x, 1.5x and 2x the thread diameter. Also included is a tap, an installation tool, a drill and a tang removal tool packed in a sturdy plastic case.

Stainless inserts. Full instructions included. Helicoil kits include a prewinder tool for fine threads or a threaded mandrel for course and metric threads. Metric and Imperial available.


There is also a good range of Inserts - Thread Repair - Helicoil Starter Sets on the Small Parts and Bearings website.


Inserts - Thread Repair - Recoil Starter Sets
Inserts - Thread Repair - Recoil Starter Sets

Also see combined categories:
All Recoil Inserts and Kits

Recoil inserts are screwed directly into an enlarged tapped hole. A tap and installation tool is included with these kits.

Stainless inserts. Contents: Ground intermediate (2nd) tap. Inserts. Installation/tang break off tool. Full instructions. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.


There is also a good range of Inserts - Thread Repair - Recoil Starter Sets on the Small Parts and Bearings website.


Inserts - Thread Repair - EZ-Lok - Individual Kits
Inserts - Thread Repair - EZ-Lok - Individual Kits

Also see combined categories:
All EZ Lok inserts and Kits

Contains 20 inserts per kit along with a standard tap, drill bit and installation tool. Installation tool is not needed but will make multiple installations easier.

Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Install with a bolt and wrench. Metric, UNC and UNF.

Related Information:
Power Drive Tools for Volume Installation

There is also a good range of Inserts - Thread Repair - EZ-Lok - Individual Kits on the Small Parts and Bearings website.


Inserts - Thread Repair - Helicoil Extracting Tools
Inserts - Thread Repair - Helicoil Extracting Tools

Extracting tools are used to remove helicoil inserts. This is done by applying the tool to the insert, striking the tools head and turning it counter-clockwide.


There is also a good range of Inserts - Thread Repair - Helicoil Extracting Tools on the Small Parts and Bearings website.


Inserts - Thread Repair - Helicoil Tang Breakoff Tools
Inserts - Thread Repair - Helicoil Tang Breakoff Tools

The driving tangs of helicoil inserts must be removed to prevent interference with the end of the assembled screw. For inserts over 1/2 inch use long nosed pliers.


There is also a good range of Inserts - Thread Repair - Helicoil Tang Breakoff Tools on the Small Parts and Bearings website.


Inserts - Thread Repair - Helicoil
Inserts - Thread Repair - Helicoil

Also see combined categories:
All Helicoil Inserts and Kits

Replacement helicoil inserts for after you have purchased a starter kit or tools separately.

Stainless 18-8 inserts with a hardness of RC43-50 and tensile strength above 200,000 PSI. Metric and Imperial available. Screw locking inserts have a series of straight segments to provide self-locking torque on the bolt, eliminating a need for other threadlocking methods.


There is also a good range of Inserts - Thread Repair - Helicoil on the Small Parts and Bearings website.


Inserts - Thread Repair - Keylocking Starter Sets
Inserts - Thread Repair - Keylocking Starter Sets

Also see combined categories:
All Keylocking Inserts and Kits

Keylocking inserts are used to repair threads by tapping the worn thread to a standard larger thread, twisting the insert into place and then driving in the keys to lock the insert. Also known as keenserts.

Each kit contains an installation tool and the quantity of inserts shown. One size per kit. Also known as keenserts, keylocking inserts are available in mild steel and stainless steel. Installation is by drilling out the old thread, countersinking, tapping new thread with a standard tap, screwing the insert until slightly below the surface, then tapping down the keys using the tool supplied and a hammer.

Related Information:
Keysteel Catalogue PDF

There is also a good range of Inserts - Thread Repair - Keylocking Starter Sets on the Small Parts and Bearings website.


You may also be interested in

Tools Threading


Tools - Installation - For Self Tapping Inserts

Also see combined categories:
All Tools

Installation tools for self tapping thread inserts - see the linked inserts categories

Related Information:
Inserts for Aluminium
Inserts for plastics
Inserts for wood

There is also a good range of Tools - Installation - For Self Tapping Inserts on the Small Parts and Bearings website.


Thread Inserts


Tools - Thread Insert - Power Drive - EZ-Lok
Tools - Thread Insert - Power Drive - EZ-Lok

Also see combined categories:
All Tools

Made from stress proof steel. The power drive tool is used for volume installation of EZ-LOK thread inserts.


There is also a good range of Tools - Thread Insert - Power Drive - EZ-Lok on the Small Parts and Bearings website.


Inserts - Self Tapping - For Plastics - Stainless 303
Inserts - Self Tapping - For Plastics - Stainless 303

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Use of installation tool recommended. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from 303 stainless steel. Quantity orders can also be supplied in Brass or 316 Stainless.

Related Information:
Installation Tools

There is also a good range of Inserts - Self Tapping - For Plastics - Stainless 303 on the Small Parts and Bearings website.


Inserts - Self Tapping - For Wood - Slotted Drive
Inserts - Self Tapping - For Wood - Slotted Drive

Also see combined categories:
All Self Tapping Inserts
All Self Tapping Inserts for Wood

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with soft plastics, hard and soft wood, particle board.

Related Information:
Installation Tools

There is also a good range of Inserts - Self Tapping - For Wood - Slotted Drive on the Small Parts and Bearings website.


Inserts - Self Tapping - For Plastics - Steel
Inserts - Self Tapping - For Plastics - Steel

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from steel with zinc chromate finish.

Related Information:
Installation Tools

There is also a good range of Inserts - Self Tapping - For Plastics - Steel on the Small Parts and Bearings website.


Inserts - Thread Repair - Keylocking
Inserts - Thread Repair - Keylocking

Also see combined categories:
All Keylocking Inserts and Kits

Steel or 303 Stainless Steel as indicated in the tables. Also known as keenserts.

Steel or 303 Stainless Steel as indicated in the tables. Maximum strength and reliability. Positive mechanical lock against rotation:. The insert kees are driven down into the tapped threads of the parent material during installation to securely lock the insert against rotation. Inserts with internal thread lock are designed to securely lock a bolt when it is entered into the insert only a few turns.

Related Information:
Keysteel Catalogue PDF

There is also a good range of Inserts - Thread Repair - Keylocking on the Small Parts and Bearings website.


Inserts - Self Tapping - For Aluminium - Steel
Inserts - Self Tapping - For Aluminium - Steel

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.

Related Information:
Installation Tools

There is also a good range of Inserts - Self Tapping - For Aluminium - Steel on the Small Parts and Bearings website.


Inserts - Self Tapping - For Aluminium - Stainless 303
Inserts - Self Tapping - For Aluminium - Stainless 303

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.

Related Information:
Installation Tools

There is also a good range of Inserts - Self Tapping - For Aluminium - Stainless 303 on the Small Parts and Bearings website.


Inserts - Rivet Nuts - Klik - Ribbed
Inserts - Rivet Nuts - Klik - Ribbed

Also see combined categories:
All Klik Rivet Nuts

Individual Inserts for use with the Klik Thread Setter Tool

These blind threaded inserts offer strong torque and pull out characteristics. Especially effective in sheet metal and other thin material. Insert is placed into the hole in the parent material and crimped up with the installation tool. Installs from one side - no tapping required. Installs almost flush eliminating the need for countersinking. Made from plated steel.

Related Information:
Thread Setter Tool
Mandrels and Nosepieces

There is also a good range of Inserts - Rivet Nuts - Klik - Ribbed on the Small Parts and Bearings website.


Tools Threading


Tools - Taps - High Speed Steel - Helicoil
Tools - Taps - High Speed Steel - Helicoil

Also see combined categories:
All Taps
All Tools

Special oversized taps to suit Helicoil Brand -tm- inserts. Intermediate and Bottoming. Inch sizes are class 2B and metric are class 5H.


There is also a good range of Tools - Taps - High Speed Steel - Helicoil on the Small Parts and Bearings website.


Thread Inserts


Inserts - Thread Repair - Keylocking Insertion Tools
Inserts - Thread Repair - Keylocking Insertion Tools

Used to insert keylocking inserts - keensert style. Keylocking inserts can be wound in without these tools but the tools make the job much easier. Also known as keenserts.

Related Information:
Keysteel Catalogue PDF

There is also a good range of Inserts - Thread Repair - Keylocking Insertion Tools on the Small Parts and Bearings website.


Inserts - Self Tapping - For Wood - Hex Drive
Inserts - Self Tapping - For Wood - Hex Drive

Also see combined categories:
All Self Tapping Inserts
All Self Tapping Inserts for Wood

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench.


There is also a good range of Inserts - Self Tapping - For Wood - Hex Drive on the Small Parts and Bearings website.


Inserts - Self Tapping - For Wood - Hex Drive - Flanged
Inserts - Self Tapping - For Wood - Hex Drive - Flanged

Also see combined categories:
All Self Tapping Inserts
All Self Tapping Inserts for Wood

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench.


There is also a good range of Inserts - Self Tapping - For Wood - Hex Drive - Flanged on the Small Parts and Bearings website.


Inserts - Self Tapping - For Wood - Slotted Drive - Short
Inserts - Self Tapping - For Wood - Slotted Drive - Short

Also see combined categories:
All Self Tapping Inserts
All Self Tapping Inserts for Wood

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Brass. Install with a screwdriver. Superior holding power in hard and soft woods, particle board and other wood products. Long pilot assists with straight driving into a drilled hole.


There is also a good range of Inserts - Self Tapping - For Wood - Slotted Drive - Short on the Small Parts and Bearings website.


Assortments


Inserts - Thread Repair - EZ-Lok - Selection Kits
Inserts - Thread Repair - EZ-Lok - Selection Kits

Also see combined categories:
All EZ Lok inserts and Kits

Contains a selection of E-Z Lok inserts

Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Install with a bolt and wrench. Metric, UNC and UNF.

Related Information:
Power Drive Tools for Volume Installation

There is also a good range of Inserts - Thread Repair - EZ-Lok - Selection Kits on the Small Parts and Bearings website.


Thread Inserts


Inserts - Thread Repair - EZ-Lok - Solid Carbon Steel
Inserts - Thread Repair - EZ-Lok - Solid Carbon Steel

Also see combined categories:
All EZ Lok inserts and Kits

Easy to install with a standard tap, bolt and wrench.

Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Install with a bolt and wrench. Metric, UNC and UNF.

Related Information:
Power Drive Tools for Volume Installation

There is also a good range of Inserts - Thread Repair - EZ-Lok - Solid Carbon Steel on the Small Parts and Bearings website.


Inserts - Thread Repair - EZ-Lok - Solid 303 Stainless Steel
Inserts - Thread Repair - EZ-Lok - Solid 303 Stainless Steel

Also see combined categories:
All EZ Lok inserts and Kits

Easy to install with a standard tap, bolt and wrench.

Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Install with a bolt and wrench. Metric, UNC and UNF.

Related Information:
Power Drive Tools for Volume Installation

There is also a good range of Inserts - Thread Repair - EZ-Lok - Solid 303 Stainless Steel on the Small Parts and Bearings website.


Inserts - Rivet Nuts - Klik - Threadsert
Inserts - Rivet Nuts - Klik - Threadsert

Also see combined categories:
All Klik Rivet Nuts

Individual Inserts for use with the Klik Thread Setter Tool

These threaded inserts can be used in blind or through hole applications. Can be used in almost any material over 2.38mm thick. As the insert is installed the threaded section is completely swaged into the sleeve portion of the hole, permitting them to be used with grade 8 screws. The installation hole size is determined by the density of the parent material. Can be pressed or otherwise compressed manually with a hammer for quick installation jobs in sheet material. Tools are available for assembly in blind holes or production assembly. Email us for a price on tools.


There is also a good range of Inserts - Rivet Nuts - Klik - Threadsert on the Small Parts and Bearings website.


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 122182 products in 2649 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 122182 products in 2649 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.