Miniature Bearings Australia Pty Ltd

Inserts Self Tapping For Wood Hex Drive Flanged Categories


Thread Inserts


Inserts - Self Tapping - For Wood - Hex Drive - Flanged
Inserts - Self Tapping - For Wood - Hex Drive - Flanged

Also see combined categories:
All Self Tapping Inserts
All Self Tapping Inserts for Wood

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench.

There is also a good range of Inserts - Self Tapping - For Wood - Hex Drive - Flanged on the Small Parts and Bearings website.


Inserts - Self Tapping - For Wood - Hex Drive
Inserts - Self Tapping - For Wood - Hex Drive

Also see combined categories:
All Self Tapping Inserts
All Self Tapping Inserts for Wood

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench.

There is also a good range of Inserts - Self Tapping - For Wood - Hex Drive on the Small Parts and Bearings website.


Inserts - Self Tapping - For Wood - Slotted Drive
Inserts - Self Tapping - For Wood - Slotted Drive

Also see combined categories:
All Self Tapping Inserts
All Self Tapping Inserts for Wood

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with soft plastics, hard and soft wood, particle board.

Related Information:

There is also a good range of Inserts - Self Tapping - For Wood - Slotted Drive on the Small Parts and Bearings website.


Inserts - Self Tapping - For Wood - Slotted Drive - Short
Inserts - Self Tapping - For Wood - Slotted Drive - Short

Also see combined categories:
All Self Tapping Inserts
All Self Tapping Inserts for Wood

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Brass. Install with a screwdriver. Superior holding power in hard and soft woods, particle board and other wood products. Long pilot assists with straight driving into a drilled hole.

There is also a good range of Inserts - Self Tapping - For Wood - Slotted Drive - Short on the Small Parts and Bearings website.


Inserts - Self Tapping - For Plastics - Steel
Inserts - Self Tapping - For Plastics - Steel

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from steel with zinc chromate finish.

Related Information:

There is also a good range of Inserts - Self Tapping - For Plastics - Steel on the Small Parts and Bearings website.


Inserts - Self Tapping - For Plastics - Stainless Steel
Inserts - Self Tapping - For Plastics - Stainless Steel

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Use of installation tool recommended. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Standard made from 303 stainless steel. Quantity orders can also be supplied in Brass or 316 Stainless.

Related Information:

There is also a good range of Inserts - Self Tapping - For Plastics - Stainless Steel on the Small Parts and Bearings website.


Screws - Self Drilling - Hex Washer Head
Screws - Self Drilling - Hex Washer Head

Also see combined categories:
All Self Drilling Screws

Zinc chromate. Fluted point. Used for fastening sheet metal to wood or metal. Drills, taps and fastens in one application.


There is also a good range of Screws - Self Drilling - Hex Washer Head on the Small Parts and Bearings website.


Inserts - Self Tapping - For Aluminium - Stainless 303
Inserts - Self Tapping - For Aluminium - Stainless 303

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.

Related Information:

There is also a good range of Inserts - Self Tapping - For Aluminium - Stainless 303 on the Small Parts and Bearings website.


Inserts - Self Tapping - For Aluminium - Steel
Inserts - Self Tapping - For Aluminium - Steel

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.

Related Information:

There is also a good range of Inserts - Self Tapping - For Aluminium - Steel on the Small Parts and Bearings website.


Tools - Installation - For Self Tapping Inserts

Also see combined categories:
All Tools

Installation tools for self tapping thread inserts - see the linked inserts categories


Related Information:

There is also a good range of Tools - Installation - For Self Tapping Inserts on the Small Parts and Bearings website.


Screws - Self Drilling - Pan Head
Screws - Self Drilling - Pan Head

Also see combined categories:
All Self Drilling Screws

Zinc chromate fluted point. Used for fastening sheet metal to wood or metal. Drills, taps and fastens in one application.


There is also a good range of Screws - Self Drilling - Pan Head on the Small Parts and Bearings website.


Nuts - Hexagonal - Nylon - Self Tapping
Nuts - Hexagonal - Nylon - Self Tapping

Also see combined categories:
All Nuts

Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.

There is also a good range of Nuts - Hexagonal - Nylon - Self Tapping on the Small Parts and Bearings website.


Screws - Self Drilling - Hex Head - With Washers
Screws - Self Drilling - Hex Head - With Washers

Also see combined categories:
All Self Drilling Screws

With bonded neoprene washer. Galvanised for corrosion resistance.


There is also a good range of Screws - Self Drilling - Hex Head - With Washers on the Small Parts and Bearings website.


Inserts - Thread Repair - Keylocking Starter Sets
Inserts - Thread Repair - Keylocking Starter Sets

Also see combined categories:
All Keylocking Inserts and Kits

Keylocking inserts are used to repair threads by tapping the worn thread to a standard larger thread, twisting the insert into place and then driving in the keys to lock the insert. Also known as keenserts.

Each kit contains an installation tool and the quantity of inserts shown. One size per kit. Also known as keenserts, keylocking inserts are available in mild steel and stainless steel. Installation is by drilling out the old thread, countersinking, tapping new thread with a standard tap, screwing the insert until slightly below the surface, then tapping down the keys using the tool supplied and a hammer.

Related Information:

There is also a good range of Inserts - Thread Repair - Keylocking Starter Sets on the Small Parts and Bearings website.


Screws - Self Tapping - Countersunk - Philips - 304 Stainless
Screws - Self Tapping - Countersunk - Philips - 304 Stainless

Also see combined categories:
All Self Tapping Screws

Countersunk screws length includes head. ie, the full overall length of the screw.

There is also a good range of Screws - Self Tapping - Countersunk - Philips - 304 Stainless on the Small Parts and Bearings website.


Screws - Self Tapping - Countersunk - Philips - 316 Stainless
Screws - Self Tapping - Countersunk - Philips - 316 Stainless

Also see combined categories:
All Self Tapping Screws

Countersunk screws length includes head. ie, the full overall length of the screw.

There is also a good range of Screws - Self Tapping - Countersunk - Philips - 316 Stainless on the Small Parts and Bearings website.


Screws - Self Tapping - Countersunk - Philips - Black Oxide
Screws - Self Tapping - Countersunk - Philips - Black Oxide

Also see combined categories:
All Self Tapping Screws

Countersunk screws length includes head. ie, the full overall length of the screw.

There is also a good range of Screws - Self Tapping - Countersunk - Philips - Black Oxide on the Small Parts and Bearings website.


Screws - Self Tapping - Countersunk - Philips - Zinc Plated
Screws - Self Tapping - Countersunk - Philips - Zinc Plated

Also see combined categories:
All Self Tapping Screws

Countersunk screws length includes head. ie, the full overall length of the screw.

There is also a good range of Screws - Self Tapping - Countersunk - Philips - Zinc Plated on the Small Parts and Bearings website.


Screws - Self Tapping - Countersunk - Undercut Head
Screws - Self Tapping - Countersunk - Undercut Head

Also see combined categories:
All Self Tapping Screws

Countersunk screws length includes head. ie, the full overall length of the screw.

There is also a good range of Screws - Self Tapping - Countersunk - Undercut Head on the Small Parts and Bearings website.


Screws - Self Tapping - For Hard or Soft Plastics - Pan Head
Screws - Self Tapping - For Hard or Soft Plastics - Pan Head

Also see combined categories:
All Self Tapping Screws
All Self Tapping Screws for Plastics

Tri-Lobe Course Thread Plastic Threading Screws

Thread cutting screws for plastics. Be sure to select correct screw for hard or soft plastic threadcutting.

There is also a good range of Screws - Self Tapping - For Hard or Soft Plastics - Pan Head on the Small Parts and Bearings website.


Screws - Self Tapping - For Soft Plastics - Pan Head
Screws - Self Tapping - For Soft Plastics - Pan Head

Also see combined categories:
All Self Tapping Screws
All Self Tapping Screws for Plastics

Tri-Lobe Course Thread Plastic Threading Screws

Thread cutting screws for plastics. Be sure to select correct screw for hard or soft plastic threadcutting.

There is also a good range of Screws - Self Tapping - For Soft Plastics - Pan Head on the Small Parts and Bearings website.


Screws - Self Tapping - Pan Head - 302 - 304 Stainless
Screws - Self Tapping - Pan Head - 302 - 304 Stainless

Also see combined categories:
All Self Tapping Screws

Type AB Steel Self Tapping Screws.

Length is from the tip of the screw to the base of the head. Ie, does not include the head.

There is also a good range of Screws - Self Tapping - Pan Head - 302 - 304 Stainless on the Small Parts and Bearings website.


Screws - Self Tapping - Pan Head - 316 Stainless
Screws - Self Tapping - Pan Head - 316 Stainless

Also see combined categories:
All Self Tapping Screws

Type AB Steel Self Tapping Screws.

Length is from the tip of the screw to the base of the head. Ie, does not include the head.

There is also a good range of Screws - Self Tapping - Pan Head - 316 Stainless on the Small Parts and Bearings website.


Screws - Self Tapping - Pan Head - Steel - Black Oxide
Screws - Self Tapping - Pan Head - Steel - Black Oxide

Also see combined categories:
All Self Tapping Screws

Type AB Steel Self Tapping Screws.

Length is from the tip of the screw to the base of the head. Ie, does not include the head.

There is also a good range of Screws - Self Tapping - Pan Head - Steel - Black Oxide on the Small Parts and Bearings website.


Screws - Self Tapping - Pan Head - Zinc Plated
Screws - Self Tapping - Pan Head - Zinc Plated

Also see combined categories:
All Self Tapping Screws

Type AB Steel Self Tapping Screws.

Length is from the tip of the screw to the base of the head. Ie, does not include the head.

There is also a good range of Screws - Self Tapping - Pan Head - Zinc Plated on the Small Parts and Bearings website.


Inserts - Expansion - Press In - Brass - Flanged
Inserts - Expansion - Press In - Brass - Flanged

Also see combined categories:
All Expansion Inserts

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.

Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.

There is also a good range of Inserts - Expansion - Press In - Brass - Flanged on the Small Parts and Bearings website.


Inserts - Expansion - Press In - 303 Stainless - Flanged
Inserts - Expansion - Press In - 303 Stainless - Flanged

Also see combined categories:
All Expansion Inserts

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.

Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.

There is also a good range of Inserts - Expansion - Press In - 303 Stainless - Flanged on the Small Parts and Bearings website.


Tools - Thread Insert - Power Drive - EZ-Lok
Tools - Thread Insert - Power Drive - EZ-Lok

Also see combined categories:
All Tools

Made from stress proof steel. The power drive tool is used for volume installation of EZ-LOK thread inserts.


There is also a good range of Tools - Thread Insert - Power Drive - EZ-Lok on the Small Parts and Bearings website.


Housings - Bearing - Flanged - Offset - Cast Iron
Housings - Bearing - Flanged - Offset - Cast Iron


Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.

Related Information:

There is also a good range of Housings - Bearing - Flanged - Offset - Cast Iron on the Small Parts and Bearings website.


Housings - Bearing - Flanged - Round - Cast Iron
Housings - Bearing - Flanged - Round - Cast Iron


Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.

Related Information:

There is also a good range of Housings - Bearing - Flanged - Round - Cast Iron on the Small Parts and Bearings website.


Housings - Bearing - Flanged - Square - Cast Iron
Housings - Bearing - Flanged - Square - Cast Iron


Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.

Related Information:

There is also a good range of Housings - Bearing - Flanged - Square - Cast Iron on the Small Parts and Bearings website.


Housings - Bearing - Flanged - 2 Bolt Hole - Aluminium
Housings - Bearing - Flanged - 2 Bolt Hole - Aluminium


Starting at 8mm bore size, aluminium silver series housings with removable chrome steel bearing


There is also a good range of Housings - Bearing - Flanged - 2 Bolt Hole - Aluminium on the Small Parts and Bearings website.


Housings - Bearing - Flanged - 2 Bolt Hole - Plastic
Housings - Bearing - Flanged - 2 Bolt Hole - Plastic


Load and speed capability depend on the bearing used. Use with steel or plastic bearing inserts for plastic housings.

Related Information:

There is also a good range of Housings - Bearing - Flanged - 2 Bolt Hole - Plastic on the Small Parts and Bearings website.


Housings - Bearing - Flanged - 3 Bolt Bracket - Plastic
Housings - Bearing - Flanged - 3 Bolt Bracket - Plastic


Load and speed capability depend on the bearing used. Use with steel bearing inserts for plastic housings.

Related Information:

There is also a good range of Housings - Bearing - Flanged - 3 Bolt Bracket - Plastic on the Small Parts and Bearings website.


Housings - Bearing - Flanged - 2 Bolt Hole - Cast Iron
Housings - Bearing - Flanged - 2 Bolt Hole - Cast Iron


Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.

Related Information:

There is also a good range of Housings - Bearing - Flanged - 2 Bolt Hole - Cast Iron on the Small Parts and Bearings website.


Housings - Bearing - Flanged - 2 Bolt Hole - Pressed Metal
Housings - Bearing - Flanged - 2 Bolt Hole - Pressed Metal


Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.

Related Information:

There is also a good range of Housings - Bearing - Flanged - 2 Bolt Hole - Pressed Metal on the Small Parts and Bearings website.


Housings - Bearing - Flanged - 3 Bolt Hole - Pressed Metal
Housings - Bearing - Flanged - 3 Bolt Hole - Pressed Metal


Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.

Related Information:

There is also a good range of Housings - Bearing - Flanged - 3 Bolt Hole - Pressed Metal on the Small Parts and Bearings website.


Inserts - Rivet Nuts - Klik - Ribbed
Inserts - Rivet Nuts - Klik - Ribbed

Also see combined categories:
All Klik Rivet Nuts

Individual Inserts for use with the Klik Thread Setter Tool

These blind threaded inserts offer strong torque and pull out characteristics. Especially effective in sheet metal and other thin material. Insert is placed into the hole in the parent material and crimped up with the installation tool. Installs from one side - no tapping required. Installs almost flush eliminating the need for countersinking. Made from plated steel.

Related Information:

There is also a good range of Inserts - Rivet Nuts - Klik - Ribbed on the Small Parts and Bearings website.


Bearings - For Cast Iron Housings
Bearings - For Cast Iron Housings


Insert bearings with spherical OD for use with cast iron flanged and pillow block housings.

Grub Screw locking. Preferred misallignment of no more than 2o, but can accommodate up to 6o. Also available with eccentric locking collars on request. Lubrication Hole to match Lubrication groove in housing.

Related Information:

There is also a good range of Bearings - For Cast Iron Housings on the Small Parts and Bearings website.


Bearings - For Pressed Metal Housings
Bearings - For Pressed Metal Housings


Insert bearings with spherical OD for use with pressed metal flanged and pillow block housings.

Grub Screw locking. Preferred misallignment of no more than 2o, but can accommodate up to 6o. Also available with eccentric locking collars on request.

Related Information:

There is also a good range of Bearings - For Pressed Metal Housings on the Small Parts and Bearings website.


Inserts - Tapered Fit - Finserts - For Wood and Plastics
Inserts - Tapered Fit - Finserts - For Wood and Plastics


Finserts provide strong metal threads in wood, composition board and thermoplastics such as nylon, polystyrene, cellulose acetate and cycolac. By distributing stress over a greater surface area, firm permanent fastening is ensured.

The fins give higher holding strength in softer materials. Available with one, two or three fins for varying material thickness. Finserts prevent splintering, splitting and thread pullout.

There is also a good range of Inserts - Tapered Fit - Finserts - For Wood and Plastics on the Small Parts and Bearings website.


Tensioner - Drive - Adjustable Flanged
Tensioner - Drive - Adjustable Flanged

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. With flanged base that can be mounted in a tight area.

Idler shaft and pulleys not included with tensioner. Rotating arm gives operator 360o controlled tensioning. Serrated teeth to prevent slippage once tightened.

Related Information:

There is also a good range of Tensioner - Drive - Adjustable Flanged on the Small Parts and Bearings website.


Inserts - Thread Repair - EZ-Lok - Selection Kits
Inserts - Thread Repair - EZ-Lok - Selection Kits

Also see combined categories:
All EZ Lok inserts and Kits

Contains a selection of E-Z Lok inserts

Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Install with a bolt and wrench. Metric, UNC and UNF.

Related Information:

There is also a good range of Inserts - Thread Repair - EZ-Lok - Selection Kits on the Small Parts and Bearings website.


Pins - Ball Lock - Flanged Receptacles
Pins - Ball Lock - Flanged Receptacles

Also see combined categories:
All Ball Lock Receptacles

Provide a permanent and proper mating hole for commercial and industrial type quick release ball lock pins. Also called detent pins.

Designed to be used on materials or in applications where the pin does not have anything to lock against. Positive lock detent pins. Pin does not protrude past the bottom of the receptacle so they are ideal for blind hole applications. 303 Stainless Steel. Mounted with screws, rivets or bolts. The quick release ball lock pins are inserted from the flanged end, and the ball extends into the wider opening at the top of the receptacle.

Related Information:

There is also a good range of Pins - Ball Lock - Flanged Receptacles on the Small Parts and Bearings website.


Inserts - Thread Repair - EZ-Lok - Solid Carbon Steel
Inserts - Thread Repair - EZ-Lok - Solid Carbon Steel

Also see combined categories:
All EZ Lok inserts and Kits

Easy to install with a standard tap, bolt and wrench.

Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Install with a bolt and wrench. Metric, UNC and UNF.

Related Information:

There is also a good range of Inserts - Thread Repair - EZ-Lok - Solid Carbon Steel on the Small Parts and Bearings website.


Inserts - Thread Repair - EZ-Lok - Solid Stainless Steel
Inserts - Thread Repair - EZ-Lok - Solid Stainless Steel

Also see combined categories:
All EZ Lok inserts and Kits

Easy to install with a standard tap, bolt and wrench.

Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Simply drill and tap the hole to suit the external thread. Install with a bolt and wrench. Metric, UNC and UNF.

Related Information:

There is also a good range of Inserts - Thread Repair - EZ-Lok - Solid Stainless Steel on the Small Parts and Bearings website.


Spacers - PCB
Spacers - PCB


Spacers for printed circuit boards

These spacers have a hex in the centre to allow for holding with a spanner whilst tightening. Fix using a 6 or 8 gauge self tapping screw.

There is also a good range of Spacers - PCB on the Small Parts and Bearings website.


Housings - Flanged - Self Aligning - Bronze - Heavy Duty
Housings - Flanged - Self Aligning - Bronze - Heavy Duty

Also see combined categories:
All Spyraflo Flange Mounted Bearings
All Spyraflo Mounted Bearings

Spyraflo robust light weight aluminium housing with self aligning bronze bearings.

See links at bottom of web page for more information. +/- 5% Static Alignment. Sintered aluminium housing. Corrosion Resistant. Light weight.

Related Information:

There is also a good range of Housings - Flanged - Self Aligning - Bronze - Heavy Duty on the Small Parts and Bearings website.


Housings - Flanged - Self Aligning - Heavy Duty - Delrin AF -tm-
Housings - Flanged - Self Aligning - Heavy Duty - Delrin AF -tm-

Also see combined categories:
All Spyraflo Flange Mounted Bearings
All Spyraflo Mounted Bearings

Spyraflo low profile self aligning flange mounted acetal Delrin AF bearings

See links at bottom of web page for more information. +/- 5% Static Alignment.

Related Information:

There is also a good range of Housings - Flanged - Self Aligning - Heavy Duty - Delrin AF -tm- on the Small Parts and Bearings website.


Housings - Flanged - Self Aligning - Heavy Duty - Delrin -tm-
Housings - Flanged - Self Aligning - Heavy Duty - Delrin -tm-

Also see combined categories:
All Spyraflo Flange Mounted Bearings
All Spyraflo Mounted Bearings

Spyraflo low profile self aligning flange mounted acetal Delrin bearings

See links at bottom of web page for more information. +/- 5% Static Alignment.

Related Information:

There is also a good range of Housings - Flanged - Self Aligning - Heavy Duty - Delrin -tm- on the Small Parts and Bearings website.


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 123604 products in 2554 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 123604 products in 2554 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.