Miniature Bearings Australia Pty Ltd

Inserts Expansion Press In 303 Stainless Flanged Categories


Thread Inserts


Inserts - Expansion - Press In - 303 Stainless - Flanged
Inserts - Expansion - Press In - 303 Stainless - Flanged

Also see combined categories:
All Expansion Inserts

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.

Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.

There is also a good range of Inserts - Expansion - Press In - 303 Stainless - Flanged on the Small Parts and Bearings website.


Inserts - Expansion - Press In - 303 Stainless Steel
Inserts - Expansion - Press In - 303 Stainless Steel

Also see combined categories:
All Expansion Inserts

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.

Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.

There is also a good range of Inserts - Expansion - Press In - 303 Stainless Steel on the Small Parts and Bearings website.


Inserts - Expansion - Press In - Brass - Flanged
Inserts - Expansion - Press In - Brass - Flanged

Also see combined categories:
All Expansion Inserts

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.

Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.

There is also a good range of Inserts - Expansion - Press In - Brass - Flanged on the Small Parts and Bearings website.


Inserts - Expansion - Press In - Brass
Inserts - Expansion - Press In - Brass

Also see combined categories:
All Expansion Inserts

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.

Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.

There is also a good range of Inserts - Expansion - Press In - Brass on the Small Parts and Bearings website.


Inserts - Self Tapping - For Aluminium - Stainless 303
Inserts - Self Tapping - For Aluminium - Stainless 303

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.

Related Information:

There is also a good range of Inserts - Self Tapping - For Aluminium - Stainless 303 on the Small Parts and Bearings website.


Inserts - Thread Repair - Keylocking
Inserts - Thread Repair - Keylocking

Also see combined categories:
All Keylocking Inserts and Kits

Steel or 303 Stainless Steel as indicated in the tables. Also known as keenserts.

Steel or 303 Stainless Steel as indicated in the tables. Maximum strength and reliability. Positive mechanical lock against rotation:. The insert kees are driven down into the tapped threads of the parent material during installation to securely lock the insert against rotation. Inserts with internal thread lock are designed to securely lock a bolt when it is entered into the insert only a few turns.

Related Information:

There is also a good range of Inserts - Thread Repair - Keylocking on the Small Parts and Bearings website.


Inserts - Self Tapping - For Plastics - Stainless Steel
Inserts - Self Tapping - For Plastics - Stainless Steel

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Use of installation tool recommended. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Standard made from 303 stainless steel. Quantity orders can also be supplied in Brass or 316 Stainless.

Related Information:

There is also a good range of Inserts - Self Tapping - For Plastics - Stainless Steel on the Small Parts and Bearings website.


Mounts - Vibration - Isolation - Compression - Stainless Steel
Mounts - Vibration - Isolation - Compression - Stainless Steel


Compression shear mounts for harsh environments.

Excellent protection against shock vibration and noise4 in compression and shear applications. Developed especially for applications in harsh environments in food and pharmaceutical industries. High dampening characteristics. Stainless top plate is domed to guard against oil contamination. Low profile. Compact design. Elastomer insert is made from highly chemical resistant nitrile with good deflection properties. Concentric rings in the base of the insert firmly anchor machine to the floor.

Related Information:

There is also a good range of Mounts - Vibration - Isolation - Compression - Stainless Steel on the Small Parts and Bearings website.


Inserts - Thread Repair - EZ-Lok - Solid Stainless Steel
Inserts - Thread Repair - EZ-Lok - Solid Stainless Steel

Also see combined categories:
All EZ Lok inserts and Kits

Easy to install with a standard tap, bolt and wrench.

Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Simply drill and tap the hole to suit the external thread. Install with a bolt and wrench. Metric, UNC and UNF.

Related Information:

There is also a good range of Inserts - Thread Repair - EZ-Lok - Solid Stainless Steel on the Small Parts and Bearings website.


Nuts - Hexagonal - Nylon Insert - Stainless Steel
Nuts - Hexagonal - Nylon Insert - Stainless Steel

Also see combined categories:
All Lock Nuts

Nylon Insert for Locking. NylocTM and other brands.

Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.

There is also a good range of Nuts - Hexagonal - Nylon Insert - Stainless Steel on the Small Parts and Bearings website.


Gears - Spur - 24DP - 20 Degree - Plastic with Insert
Gears - Spur -  24DP - 20 Degree - Plastic with Insert

Also see combined categories:
All 24DP Spur Gears 20 Degree
All 24DP Spur Gears 20 Degree Plastic

PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Acetal or Nylon w/ Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

There is also a good range of Gears - Spur - 24DP - 20 Degree - Plastic with Insert on the Small Parts and Bearings website.


Bearings - Acetal with Stainless Balls - For Plastic Housings
Bearings - Acetal with Stainless Balls - For Plastic Housings

Also see combined categories:
All Acetal Bearings for Housings

Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.

Load and speed calculations are for reference only. Testing is recommended.

Related Information:

There is also a good range of Bearings - Acetal with Stainless Balls - For Plastic Housings on the Small Parts and Bearings website.


Bearings - 316 Stainless Steel - Spherical OD - For Plastic Housings
Bearings - 316 Stainless Steel - Spherical OD - For Plastic Housings


Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.

Load and speed calculations are for reference only. Testing is recommended.

Related Information:

There is also a good range of Bearings - 316 Stainless Steel - Spherical OD - For Plastic Housings on the Small Parts and Bearings website.


Inserts - Thread Repair - Helicoil
Inserts - Thread Repair - Helicoil

Also see combined categories:
All Helicoil Inserts and Kits

Replacement helicoil inserts for after you have purchased a starter kit or tools separately.

Stainless 18-8 inserts with a hardness of RC43-50 and tensile strength above 200,000 PSI. Metric and Imperial available. Screw locking inserts have a series of straight segments to provide self-locking torque on the bolt, eliminating a need for other threadlocking methods.

There is also a good range of Inserts - Thread Repair - Helicoil on the Small Parts and Bearings website.


Gears - Spur - 24DP - 20 Degree - Brass
Gears - Spur -  24DP - 20 Degree - Brass

Also see combined categories:
All 24DP Spur Gears 20 Degree
All 24DP Spur Gears 20 Degree Metal

PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Acetal or Nylon w/ Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

There is also a good range of Gears - Spur - 24DP - 20 Degree - Brass on the Small Parts and Bearings website.


Gears - Spur - 24DP - 20 Degree - Plastic with No Hub
Gears - Spur -  24DP - 20 Degree - Plastic with No Hub

Also see combined categories:
All 24DP Spur Gears 20 Degree
All 24DP Spur Gears 20 Degree Plastic

PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

There is also a good range of Gears - Spur - 24DP - 20 Degree - Plastic with No Hub on the Small Parts and Bearings website.


Bearings - Conveyor - Hex Bore - Stainless Steel - Double Row
Bearings - Conveyor - Hex Bore - Stainless Steel - Double Row

Also see combined categories:
All Conveyor Bearings

316 stainless conveyor bearings with plastic cage and plastic hex insert

Loads and Speeds are for reference only. Testing recommended.

There is also a good range of Bearings - Conveyor - Hex Bore - Stainless Steel - Double Row on the Small Parts and Bearings website.


Bearings - Conveyor - Hex Bore - Stainless Steel - Single Row
Bearings - Conveyor - Hex Bore - Stainless Steel - Single Row

Also see combined categories:
All Conveyor Bearings

316 stainless conveyor bearings with plastic cage and plastic hex insert

Loads and Speeds are for reference only. Testing recommended.

There is also a good range of Bearings - Conveyor - Hex Bore - Stainless Steel - Single Row on the Small Parts and Bearings website.


Inserts - Thread Repair - Helicoil Starter Sets
Inserts - Thread Repair - Helicoil Starter Sets

Also see combined categories:
All Helicoil Inserts and Kits

Helicoil sets include 3 lengths of 1x, 1.5x and 2x the thread diameter. Also included is a tap, an installation tool, a drill and a tang removal tool packed in a sturdy plastic case.

Stainless inserts. Full instructions included. Helicoil kits include a prewinder tool for fine threads or a threaded mandrel for course and metric threads. Metric and Imperial available.

There is also a good range of Inserts - Thread Repair - Helicoil Starter Sets on the Small Parts and Bearings website.


Gears - Spur - 24DP - 20 Degree - Plastic - Plain
Gears - Spur -  24DP - 20 Degree - Plastic - Plain

Also see combined categories:
All 24DP Spur Gears 20 Degree
All 24DP Spur Gears 20 Degree Plastic

PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Acetal or Nylon w/ Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

There is also a good range of Gears - Spur - 24DP - 20 Degree - Plastic - Plain on the Small Parts and Bearings website.


Inserts - Thread Repair - Recoil
Inserts - Thread Repair - Recoil

Also see combined categories:
All Recoil Inserts and Kits

Recoil inserts are screwed directly into an enlarged tapped hole. Replacement inserts for your kit.

Stainless inserts. Replacement Individual Inserts - Require full kit to obtain correct tap. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.

There is also a good range of Inserts - Thread Repair - Recoil on the Small Parts and Bearings website.


Gears - Spur - 120DP - Stainless
Gears - Spur - 120DP - Stainless

Also see combined categories:
All 120DP Spur Gears
All Metal 120DP Spur Gears

PCD = No. of Teeth x 0.212mm (1/120 in.). 20o Pressure Angle. 303 stainless steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 120 Diametrical Pitch. Approx 0.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

There is also a good range of Gears - Spur - 120DP - Stainless on the Small Parts and Bearings website.


Gears - Spur - 80DP - Stainless
Gears - Spur -  80DP - Stainless

Also see combined categories:
All 80DP Spur Gears
All Metal 80DP Spur Gears

PCD = No. of Teeth x 0.318mm (1/80 in.). 20o Pressure Angle. 303 stainless steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 80 Diametrical Pitch. Approx 1mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

There is also a good range of Gears - Spur - 80DP - Stainless on the Small Parts and Bearings website.


Gears - Spur - 96DP - Stainless
Gears - Spur -  96DP - Stainless

Also see combined categories:
All 96DP Spur Gears
All Metal 96DP Spur Gears

PCD = No. of Teeth x 0.265mm (1/96 in.). 20o Pressure Angle. 303 stainless steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 96 Diametrical Pitch. Approx 0.83mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

There is also a good range of Gears - Spur - 96DP - Stainless on the Small Parts and Bearings website.


Housings - Bearing - Tapped Base Unit - Stainless
Housings - Bearing - Tapped Base Unit - Stainless


Full stainless steel bearing units are the best solution for hostile chemical washdown applications. All metal bearing insert components are a combination of 302, 304 and 440 stainless steel. Seals are silicone rubber. Grease is H-1 food grade.

Operating temperature minus 20 oC to +120 deg C. Solid 304 stainless housings have a machined base and extremely smooth surface finish, essential for demanding washdown installations. These housings do not experience flaking, cracking or discolouration and are virtually unaffected by scrapes. Bearings are removable. Food grade.

There is also a good range of Housings - Bearing - Tapped Base Unit - Stainless on the Small Parts and Bearings website.


Inserts - Thread Repair - Recoil Starter Sets
Inserts - Thread Repair - Recoil Starter Sets

Also see combined categories:
All Recoil Inserts and Kits

Recoil inserts are screwed directly into an enlarged tapped hole. A tap and installation tool is included with these kits.

Stainless inserts. Contents: Ground intermediate (2nd) tap. Inserts. Installation/tang break off tool. Full instructions. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.

There is also a good range of Inserts - Thread Repair - Recoil Starter Sets on the Small Parts and Bearings website.


Gears - Spur - 24DP - 20 Degree - Stainless
Gears - Spur -  24DP - 20 Degree - Stainless

Also see combined categories:
All 24DP Spur Gears 20 Degree
All 24DP Spur Gears 20 Degree Metal

PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. 303 Stainless Steel. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

There is also a good range of Gears - Spur - 24DP - 20 Degree - Stainless on the Small Parts and Bearings website.


Gears - Spur - 32DP - 20 Degree - Stainless
Gears - Spur -  32DP - 20 Degree - Stainless

Also see combined categories:
All 32DP Spur Gears 20 Degree
All 32DP Spur Gears 20 Degree Metal

PCD = No. of Teeth x 0.794mm (1/32 in.). 20o Pressure Angle. 303 Stainless Steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

There is also a good range of Gears - Spur - 32DP - 20 Degree - Stainless on the Small Parts and Bearings website.


Gears - Spur - 48DP - 20 Degree - Stainless
Gears - Spur -  48DP - 20 Degree - Stainless

Also see combined categories:
All 48DP Spur Gears 20 Degree
All 48DP Spur Gears 20 Degree Metal

PCD = No. of Teeth x 0.529mm (1/48 in.). 20o Pressure Angle. 303 stainless steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 48 Diametrical Pitch. Approx 1.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

There is also a good range of Gears - Spur - 48DP - 20 Degree - Stainless on the Small Parts and Bearings website.


Sprockets - 3.75 x 1.6mm - Simplex - Plastic
Sprockets -  3.75 x 1.6mm - Simplex - Plastic

Also see combined categories:
All Sprockets for Roller Chain

Nylon - Acetal - With and without bore inserts.

Match with series 3.75mm miniature plastic or stainless chain.

Related Information:

There is also a good range of Sprockets - 3.75 x 1.6mm - Simplex - Plastic on the Small Parts and Bearings website.


Plungers - Indexing - Locking - With Knob - 303 stainless Steel
Plungers - Indexing - Locking - With Knob - 303 stainless Steel

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.

303 Stainless Steel.

There is also a good range of Plungers - Indexing - Locking - With Knob - 303 stainless Steel on the Small Parts and Bearings website.


Plungers - Indexing - Non Locking - With Knob - 303 Stainless Steel
Plungers - Indexing - Non Locking - With Knob - 303 Stainless Steel

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.

303 Stainless Steel.

There is also a good range of Plungers - Indexing - Non Locking - With Knob - 303 Stainless Steel on the Small Parts and Bearings website.


Plungers - Indexing - Non Locking - Without Knob - 303 Stainless Steel
Plungers - Indexing - Non Locking - Without Knob - 303 Stainless Steel

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.

303 Stainless Steel.

There is also a good range of Plungers - Indexing - Non Locking - Without Knob - 303 Stainless Steel on the Small Parts and Bearings website.


Balls - Tooling - One Piece - Shoulder - Stainless Steel - Press Fit
Balls - Tooling - One Piece - Shoulder - Stainless Steel - Press Fit

Also see combined categories:
All Tooling Balls
All Shoulder Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 440C Stainless Steel heat treated to 55-58 RC.

Related Information:

There is also a good range of Balls - Tooling - One Piece - Shoulder - Stainless Steel - Press Fit on the Small Parts and Bearings website.


Balls - Tooling - One Piece - Standard - Stainless Steel - Press Fit
Balls - Tooling - One Piece - Standard - Stainless Steel - Press Fit

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

440C Stainless Steel heat treated to 55-58 RC.

Related Information:

There is also a good range of Balls - Tooling - One Piece - Standard - Stainless Steel - Press Fit on the Small Parts and Bearings website.


Pins - Dowel - Standard - 303-304 Stainless - Chamfered End
Pins - Dowel - Standard - 303-304 Stainless - Chamfered End

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 303/304 Grade Stainless - DIN6325, ISO2338, ISO 8734

Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.

Related Information:

There is also a good range of Pins - Dowel - Standard - 303-304 Stainless - Chamfered End on the Small Parts and Bearings website.


Gears - Spur - Module 0.5 - Stainless
Gears - Spur - Module 0.5 - Stainless

Also see combined categories:
All Module 0.5 Spur Gears
All Metal Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

There is also a good range of Gears - Spur - Module 0.5 - Stainless on the Small Parts and Bearings website.


Gears - Spur - Module 0.8 - Stainless
Gears - Spur - Module 0.8 - Stainless

Also see combined categories:
All Module 0.8 Spur Gears
All Metal Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

There is also a good range of Gears - Spur - Module 0.8 - Stainless on the Small Parts and Bearings website.


Gears - Spur - Module 1.25 - Stainless
Gears - Spur - Module 1.25 - Stainless

Also see combined categories:
All Module 1.25 Spur Gears
All Metal Module 1.25 Spur Gears

PCD = No. of Teeth x 1.250mm. 20o Pressure Angle. 303 stainless steel

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

There is also a good range of Gears - Spur - Module 1.25 - Stainless on the Small Parts and Bearings website.


Gears - Spur - Module 1.5 - Stainless
Gears - Spur - Module 1.5 - Stainless

Also see combined categories:
All Module 1.5 Spur Gears
All Metal Module 1.5 Spur Gears

PCD = No. of Teeth x 1.500mm. 20o Pressure Angle. 303 stainless steel

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

There is also a good range of Gears - Spur - Module 1.5 - Stainless on the Small Parts and Bearings website.


Gears - Spur - Module 2.5 - Stainless
Gears - Spur - Module 2.5 - Stainless

Also see combined categories:
All Module 2.5 Spur Gears
All Metal Module 2.5 Spur Gears

PCD = No. of Teeth x 2.500mm. 20o Pressure Angle. 303 stainless steel

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

There is also a good range of Gears - Spur - Module 2.5 - Stainless on the Small Parts and Bearings website.


Pins - Hammer Drive - Round Head - Stainless Steel
Pins - Hammer Drive - Round Head - Stainless Steel

Also see combined categories:
All Hammer Drive Pins

Used to replace screws where the need to remove the pin is unlikely.

Stainless Steel 304 Grade. Simple, low cost assembly. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.

Related Information:

There is also a good range of Pins - Hammer Drive - Round Head - Stainless Steel on the Small Parts and Bearings website.


Gears - Spur - Module 1 - Stainless
Gears - Spur - Module 1 - Stainless

Also see combined categories:
All Module 1.0 Spur Gears
All Metal Module 1.0 Spur Gears

PCD = No. of Teeth x 1.000mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

There is also a good range of Gears - Spur - Module 1 - Stainless on the Small Parts and Bearings website.


Gears - Spur - Module 2 - Stainless
Gears - Spur - Module 2 - Stainless

Also see combined categories:
All Module 2.0 Spur Gears
All Metal Module 2.0 Spur Gears

PCD = No. of Teeth x 2.000mm. 20o Pressure Angle. 303 stainless steel

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

There is also a good range of Gears - Spur - Module 2 - Stainless on the Small Parts and Bearings website.


Gears - Spur - Module 3 - Stainless
Gears - Spur - Module 3 - Stainless

Also see combined categories:
All Module 3.0 Spur Gears
All Metal Module 3.0 Spur Gears

PCD = No. of Teeth x 3.000mm. 20o Pressure Angle. 303 stainless steel

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

There is also a good range of Gears - Spur - Module 3 - Stainless on the Small Parts and Bearings website.


Catches - Snap In Style - Grabber -tm-
Catches - Snap In Style - Grabber -tm-


Fast economical installation.

Fits frames from 1.1 to 7.1mm thick. Installation hole size 15mm x 39.9mm. Push to close and pull to open. Spring loaded over centre action. Corrosion resistant black ABS with 303 stainless steel spring.

There is also a good range of Catches - Snap In Style - Grabber -tm- on the Small Parts and Bearings website.


Balls - Tooling - One Piece - Shoulder - Stainless Steel - Slip Fit
Balls - Tooling - One Piece - Shoulder - Stainless Steel - Slip Fit

Also see combined categories:
All Tooling Balls
All Shoulder Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 440C Stainless Steel heat treated to 55-58 RC.

Related Information:

There is also a good range of Balls - Tooling - One Piece - Shoulder - Stainless Steel - Slip Fit on the Small Parts and Bearings website.


Balls - Tooling - One Piece - Standard - Stainless Steel - Slip Fit
Balls - Tooling - One Piece - Standard - Stainless Steel - Slip Fit

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

440C Stainless Steel heat treated to 55-58 RC.

Related Information:

There is also a good range of Balls - Tooling - One Piece - Standard - Stainless Steel - Slip Fit on the Small Parts and Bearings website.


Mounts - Leveling - 303 Stainless - Industrial - With Acetal Pad
Mounts - Leveling - 303 Stainless - Industrial - With Acetal Pad

Also see combined categories:
All Pivotal Levelers
All Mounting Feet

These industrial glides are an excellent and inexpensive solution for light duty applications such as office furniture, shelving, point of sale displays, cabinetry and small machinery. Adjusters.

303 Stainless Steel. Nylon pad for glide applications.

Related Information:

There is also a good range of Mounts - Leveling - 303 Stainless - Industrial - With Acetal Pad on the Small Parts and Bearings website.


Mounts - Leveling - 303 Stainless - Industrial - With Elastomer Pad
Mounts - Leveling - 303 Stainless - Industrial - With Elastomer Pad

Also see combined categories:
All Pivotal Levelers
All Mounting Feet

These industrial mounts are an excellent and inexpensive solution for light duty applications such as office furniture, shelving, point of sale displays, cabinetry and small machinery. Adjusters.

303 Stainless Steel. Elastomer pad for non skid applications.

Related Information:

There is also a good range of Mounts - Leveling - 303 Stainless - Industrial - With Elastomer Pad on the Small Parts and Bearings website.


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 123604 products in 2555 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 123604 products in 2555 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.