Miniature Bearings Australia Pty Ltd

Covid-19 Update!! Current supply status.

Trading by online order and email.
Outbound Deliveries: Allow a few extra days within Australia and extra 7 days for overseas deliveries.
Pre-orders and Backorders: Allow extra 7 days due to quarantine precautions.
Distributors: Most MBA distributors are open and able to contact us using the distributor phone line.

Hospitals, medical equipment repairs and manufacture and bio research teams please email us if you need emergency contacts for equipment spare parts.

Catches Side Mount Grabber Tm Categories


Catches


Catches - Side Mount - Grabber -tm-
Catches - Side Mount - Grabber -tm-


Mounts inside your enclosure. Installs either right or left side by inverting. Use 4 gauge screws or 1/8in (3.125mm) rivets to install.


There is also a good range of Catches - Side Mount - Grabber -tm- on the Small Parts and Bearings website.


Catches - Side Mount - With Microswitch - Grabber -tm-
Catches - Side Mount - With Microswitch - Grabber -tm-


Mounts inside your enclosure. Installs either right or left side by inverting. Use 4 gauge screws or 1/8in (3.125mm) rivets to install.

Switch is designed to operate as an indicator light or form part of a non-safety related logic circuit.

There is also a good range of Catches - Side Mount - With Microswitch - Grabber -tm- on the Small Parts and Bearings website.


Catches - Snap In Style - Grabber -tm-
Catches - Snap In Style - Grabber -tm-


Fast economical installation.

Fits frames from 1.1 to 7.1mm thick. Installation hole size 15mm x 39.9mm. Push to close and pull to open. Spring loaded over centre action. Corrosion resistant black ABS with 303 stainless steel spring.

There is also a good range of Catches - Snap In Style - Grabber -tm- on the Small Parts and Bearings website.


Rings - Hoist - Side Pull - External Wrench Mount
Rings - Hoist - Side Pull - External Wrench Mount

Also see combined categories:
All Hoist Rings

Ideal for flipping fixtures, dies and moulds. The hoist ring is low profile and has a unique bolt retention design. The oversized forged bail easily adapts to larger hoist hooks. Relatively light weight makes it easier to handle than similar rings.

Convenient installation with external wrenching. Alloy steel with black oxide finish. Safety factor 5 to 1. Proof tested to 200 percent of rated load capacity. DO NOT EXCEED WORKING LOAD LIMITS.

There is also a good range of Rings - Hoist - Side Pull - External Wrench Mount on the Small Parts and Bearings website.


Rings - Hoist - Side Pull - Internal-External Wrench Mount
Rings - Hoist - Side Pull - Internal-External Wrench Mount

Also see combined categories:
All Hoist Rings

Ideal for flipping fixtures, dies and moulds. The hoist ring is low profile and has a unique bolt retention design. The oversized forged bail easily adapts to larger hoist hooks. Relatively light weight makes it easier to handle than similar rings.

Convenient installation with internal or external wrenching. Alloy steel with black oxide finish. Safety factor 5 to 1. Proof tested to 200 percent of rated load capacity. DO NOT EXCEED WORKING LOAD LIMITS.

There is also a good range of Rings - Hoist - Side Pull - Internal-External Wrench Mount on the Small Parts and Bearings website.


Tensioner - Horizontal Mount
Tensioner - Horizontal Mount

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Has 88.9mm travel and is mounted 90o to the length of the part. Both ends are tapped so the shaft can be threaded on either side of the tensioner.

Idler shaft and pulleys not included with tensioner. Hole is tapped to accept 38.1mm diameter idler shaft (ordered separately).

Related Information:

There is also a good range of Tensioner - Horizontal Mount on the Small Parts and Bearings website.


Slides - Drawer - Medium Duty - Easy Disconnect
Slides - Drawer - Medium Duty - Easy Disconnect

Also see combined categories:
All Drawer Slides

Used for shallow drawers, tool chests and medical carts.

Rail mounting. Hold in detent. Full extension. 13.5mm Side space. Includes 32mm hole pattern as well as traditional hole pattern.

There is also a good range of Slides - Drawer - Medium Duty - Easy Disconnect on the Small Parts and Bearings website.


Bearings - Press-Fit - Self Aligning - Delrin -tm-
Bearings - Press-Fit - Self Aligning - Delrin -tm-

Also see combined categories:
All Spyraflo Mounted Bearings

Spyraflo acetal bearings in specially designed press fit retainers

See links at bottom of web page for more information. +/- 5% Static Alignment. Use punch of min dia. J relieved to dia. K x 2mm deep. Refer datasheet for dia. K and J. Link at bottom of web page.

Related Information:

There is also a good range of Bearings - Press-Fit - Self Aligning - Delrin -tm- on the Small Parts and Bearings website.


Bearings - Self Clinching - Self Aligning - Delrin -tm-
Bearings - Self Clinching - Self Aligning - Delrin -tm-

Also see combined categories:
All Spyraflo Mounted Bearings

Spyraflo acetal bearings in a special steel self-clinching housing. Refer technical sheets linked at bottom of tables.

See links at bottom of web page for more information. +/- 5% Static Alignment. See animation link at bottom of web page. Panel material no harder than RB65/RB75. Panel hole to be punched or machined to size A (+0.07/-0.00mm).

Related Information:

There is also a good range of Bearings - Self Clinching - Self Aligning - Delrin -tm- on the Small Parts and Bearings website.


Housings - Bearing - Flange Mounted - Frelon - Self Aligning
Housings - Bearing - Flange Mounted - Frelon - Self Aligning


Single and double length

Bearing is Frelon Gold -tm- encased in a flanged housing made from 6061-T6 aluminium. Double length has two bearings mounted internally. For rotating and linear motion.

There is also a good range of Housings - Bearing - Flange Mounted - Frelon - Self Aligning on the Small Parts and Bearings website.


Housings - Flanged - Self Aligning - Heavy Duty - Delrin -tm-
Housings - Flanged - Self Aligning - Heavy Duty - Delrin -tm-

Also see combined categories:
All Spyraflo Flange Mounted Bearings
All Spyraflo Mounted Bearings

Spyraflo low profile self aligning flange mounted acetal Delrin bearings

See links at bottom of web page for more information. +/- 5% Static Alignment.

Related Information:

There is also a good range of Housings - Flanged - Self Aligning - Heavy Duty - Delrin -tm- on the Small Parts and Bearings website.


Bearings - Self Clinching - Self Aligning - Stainless and Delrin -tm-
Bearings - Self Clinching - Self Aligning - Stainless and Delrin -tm-

Also see combined categories:
All Spyraflo Mounted Bearings

Spyraflo acetal bearings in a special stainless steel self-clinching housing. Refer technical sheets linked at bottom of tables.

See links at bottom of web page for more information. +/- 5% Static Alignment. See animation link at bottom of web page. Panel material no harder than RB65/RB75. Panel hole to be punched or machined to size A (+0.07/-0.00mm).

Related Information:

There is also a good range of Bearings - Self Clinching - Self Aligning - Stainless and Delrin -tm- on the Small Parts and Bearings website.


Housings - Flanged - Self Aligning - Heavy Duty - Delrin AF -tm-
Housings - Flanged - Self Aligning - Heavy Duty - Delrin AF -tm-

Also see combined categories:
All Spyraflo Flange Mounted Bearings
All Spyraflo Mounted Bearings

Spyraflo low profile self aligning flange mounted acetal Delrin AF bearings

See links at bottom of web page for more information. +/- 5% Static Alignment.

Related Information:

There is also a good range of Housings - Flanged - Self Aligning - Heavy Duty - Delrin AF -tm- on the Small Parts and Bearings website.


Slides - Drawer - Front Disconnect - Friction - 19mm Ext
Slides - Drawer - Front Disconnect - Friction - 19mm Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted two member slide. Friction brake allows drawer to come to a slow stop. Front disconnects by pulling firmly on the drawer until it releases. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).

There is also a good range of Slides - Drawer - Front Disconnect - Friction - 19mm Ext on the Small Parts and Bearings website.


Slides - Drawer - Front Disconnect - Lever - Full Ext
Slides - Drawer - Front Disconnect - Lever - Full Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Front disconnects by lifting a lever lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).

There is also a good range of Slides - Drawer - Front Disconnect - Lever - Full Ext on the Small Parts and Bearings website.


Slides - Drawer - Front Disconnect - Latch Lever - Full Ext
Slides - Drawer - Front Disconnect - Latch Lever - Full Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Front disconnects by pressing a drawer latch lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).

There is also a good range of Slides - Drawer - Front Disconnect - Latch Lever - Full Ext on the Small Parts and Bearings website.


Slides - Drawer - Quick Disconnect - Medium Duty - Full Ext
Slides - Drawer - Quick Disconnect - Medium Duty - Full Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Positive stop slide with a quick disconnect.

There is also a good range of Slides - Drawer - Quick Disconnect - Medium Duty - Full Ext on the Small Parts and Bearings website.


Slides - Drawer - Stainless - Front Disconnect - Lever - 19mm Ext
Slides - Drawer - Stainless - Front Disconnect - Lever - 19mm Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted two member slide. Positive locking mechanism keeps drawer locked in the open position until actively released. Front disconnects by pressing a drawer latch lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).

There is also a good range of Slides - Drawer - Stainless - Front Disconnect - Lever - 19mm Ext on the Small Parts and Bearings website.


Slides - Drawer - Stainless - No Disconnect - Heavy Duty - 19mm Ext
Slides - Drawer - Stainless - No Disconnect - Heavy Duty - 19mm Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted two member slide. Positive stop slide that will not disconnect once installed. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).

There is also a good range of Slides - Drawer - Stainless - No Disconnect - Heavy Duty - 19mm Ext on the Small Parts and Bearings website.


Slides - Drawer - Stainless - No Disconnect - Heavy Duty - Full Ext
Slides - Drawer - Stainless - No Disconnect - Heavy Duty - Full Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Positive stop slide that will not disconnect once installed.

There is also a good range of Slides - Drawer - Stainless - No Disconnect - Heavy Duty - Full Ext on the Small Parts and Bearings website.


Slides - Drawer - Stainless - No Disconnect - Medium Duty - 19mm Ext
Slides - Drawer - Stainless - No Disconnect - Medium Duty - 19mm Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted two member slide. Positive stop slide that will not disconnect once installed. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).

There is also a good range of Slides - Drawer - Stainless - No Disconnect - Medium Duty - 19mm Ext on the Small Parts and Bearings website.


Slides - Drawer - Stainless - No Disconnect - Medium Duty - Full Ext
Slides - Drawer - Stainless - No Disconnect - Medium Duty - Full Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Positive stop slide that will not disconnect once installed.

There is also a good range of Slides - Drawer - Stainless - No Disconnect - Medium Duty - Full Ext on the Small Parts and Bearings website.


Catches - Compression Spring
Catches - Compression Spring


Three internal compression springs supply up to 30kg of spring tension. Available as padlockable or with secondary catch.

Spring tension compensates for gasket set. Provides exact tension for water tight and air tight seals.

There is also a good range of Catches - Compression Spring on the Small Parts and Bearings website.


Catches - Draw Pull
Catches - Draw Pull


Draw pull catches are available in either steel or 304 stainless. Strike is included.


There is also a good range of Catches - Draw Pull on the Small Parts and Bearings website.


Catches - Knuckle
Catches - Knuckle


Strong and light polyacetal and polyamide. Holds cabinets secure with 7kg of pull force.


There is also a good range of Catches - Knuckle on the Small Parts and Bearings website.


Catches - Magnetic - Screw On
Catches - Magnetic - Screw On


Various styles - refer pictures


There is also a good range of Catches - Magnetic - Screw On on the Small Parts and Bearings website.


Catches - Magnetic - Ultra Thin - Heavy Duty
Catches - Magnetic - Ultra Thin - Heavy Duty


Ultra thin strong magnetic catch is perfect for tight areas. Has a full 4kg of magnetic force.


Related Information:

There is also a good range of Catches - Magnetic - Ultra Thin - Heavy Duty on the Small Parts and Bearings website.


Catches - Magnetic - Ultra Thin - Light Duty
Catches - Magnetic - Ultra Thin - Light Duty


Ultra thin strong magnetic catch is perfect for tight areas. Has 2.5 kg of magnetic force.


Related Information:

There is also a good range of Catches - Magnetic - Ultra Thin - Light Duty on the Small Parts and Bearings website.


Catches - Roller
Catches - Roller


304 Stainless Steel and Polyurethane


There is also a good range of Catches - Roller on the Small Parts and Bearings website.


Catches - Rotary
Catches - Rotary


Polyacetal catch and strike with polyethylene rollers. Ideal in corrosive environments.


There is also a good range of Catches - Rotary on the Small Parts and Bearings website.


Tensioner - Heavy Duty - Type 2
Tensioner - Heavy Duty - Type 2

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Has 152.4mm travel through the use of the adjusting slots. Head is drilled and tapped to accept 50.8mm diameter idler shaft (ordered separately).

Idler shaft and pulleys not included with tensioner. Shaft is mounted to the side at 90o and is anchored by set screws.

Related Information:

There is also a good range of Tensioner - Heavy Duty - Type 2 on the Small Parts and Bearings website.


Clamps - Lorenz
Clamps - Lorenz


Patented quick clamp is ideal for door openings on bins, hoppers, tanks and manholes. T-Handle allows torque without tools. The one piece unit is made from highly polished 304 stainless steel.

Full 50.8mm adjustment. 180o pivot when disengaged leaving access doorway unobstructed. Will not loosen through vibration. Brackets supplied for easy installation.

There is also a good range of Clamps - Lorenz on the Small Parts and Bearings website.


Housings - Bearing - Pillow Block - Frelon - Precision - Closed
Housings - Bearing - Pillow Block - Frelon - Precision - Closed


Single and double length

Bearing is Frelon Gold -tm- encased in a flanged housing made from 6061-T6 aluminium. Double length has two bearings mounted internally. For rotating and linear motion.

There is also a good range of Housings - Bearing - Pillow Block - Frelon - Precision - Closed on the Small Parts and Bearings website.


Housings - Bearing - Pillow Block - Frelon - Precision - Open
Housings - Bearing - Pillow Block - Frelon - Precision - Open


Single and double length

Bearing is Frelon Gold -tm- encased in a flanged housing made from 6061-T6 aluminium. Double length has two bearings mounted internally. For rotating and linear motion.

There is also a good range of Housings - Bearing - Pillow Block - Frelon - Precision - Open on the Small Parts and Bearings website.


Mounts - Buffer - Female
Mounts - Buffer - Female

Also see combined categories:
All Cylindrical Mounts

Vibration dampening


Related Information:

There is also a good range of Mounts - Buffer - Female on the Small Parts and Bearings website.


Mounts - Buffer - Male
Mounts - Buffer - Male

Also see combined categories:
All Cylindrical Mounts

Vibration dampening


Related Information:

There is also a good range of Mounts - Buffer - Male on the Small Parts and Bearings website.


Mounts - Buffer - Male - Conical
Mounts - Buffer - Male - Conical

Also see combined categories:
All Cylindrical Mounts

Rubber hardness 60 Duro Standard unless otherwise noted. Vibration dampening


Related Information:

There is also a good range of Mounts - Buffer - Male - Conical on the Small Parts and Bearings website.


Mounts - Buffer - Special Purpose
Mounts - Buffer - Special Purpose

Also see combined categories:
All Cylindrical Mounts

Vibration dampening

Natural rubber with bonded in studs. 50 Durometer hardness. Use up to 65 Degrees C (150 Deg F).

Related Information:

There is also a good range of Mounts - Buffer - Special Purpose on the Small Parts and Bearings website.


Mounts - Universal - For Acme Thread and Ballscrews
Mounts - Universal - For Acme Thread and Ballscrews


Use grade 8 hex socket head cap screws for mounting.


Related Information:

There is also a good range of Mounts - Universal - For Acme Thread and Ballscrews on the Small Parts and Bearings website.


Mounts - Vibro-Insulator Strips
Mounts - Vibro-Insulator Strips


Vibration dampening


Related Information:

There is also a good range of Mounts - Vibro-Insulator Strips on the Small Parts and Bearings website.


Mounts - Vibration Isolating - Tee Bushes
Mounts - Vibration Isolating - Tee Bushes


Vibration isolation for mobile and static applications involving plate clamping

Reduces structure borne noise and absorbs shock forces. Low profile height.

Related Information:

There is also a good range of Mounts - Vibration Isolating - Tee Bushes on the Small Parts and Bearings website.


Mounts - Vibration - Isolation - Compression - Stainless Steel
Mounts - Vibration - Isolation - Compression - Stainless Steel


Compression shear mounts for harsh environments.

Excellent protection against shock vibration and noise4 in compression and shear applications. Developed especially for applications in harsh environments in food and pharmaceutical industries. High dampening characteristics. Stainless top plate is domed to guard against oil contamination. Low profile. Compact design. Elastomer insert is made from highly chemical resistant nitrile with good deflection properties. Concentric rings in the base of the insert firmly anchor machine to the floor.

Related Information:

There is also a good range of Mounts - Vibration - Isolation - Compression - Stainless Steel on the Small Parts and Bearings website.


Mounts - Vibration - Isolation - Cup Style 2
Mounts - Vibration - Isolation - Cup Style 2

Also see combined categories:
All Cup Mounts

Industrial cupmounts provide excellent protection against severe impact shock, vibration and noise.

High vibration dampening. Fail safe, rugged interlocking metal and neoprene construction. Metal cupmount is cold rolled steel. Low profile compact design. Metal top plate is domed shape to guard against oil contamination. High grade neoprene elastomer provides resistance to ozone and oils.

Related Information:

There is also a good range of Mounts - Vibration - Isolation - Cup Style 2 on the Small Parts and Bearings website.


Mounts - Vibration - Isolation Pads - Compression Shear
Mounts - Vibration - Isolation Pads - Compression Shear

Also see combined categories:
All Isolation Pad Mounts

Durable, high quality mount combines effective compression and shear isolation from vibration and shock with the convenience of an internal leveling device.

Deep cavity design allows excellent vibration and shock control in both the vertical and horizontal directions. Heavy duty ductile iron cover and chemically resistant neoprene insert. Internal leveling device levels up to 12.7mm. Specially designed recess on top of cover hosues a rubber washer. Concentric rings on base of neoprene insert prevents walking or creeping. Ideal for lathes, milling machines, punch presses, printing machines, shears, brakes, injection moulding machines, grinders etc. Includes all necessary hardware.

Related Information:

There is also a good range of Mounts - Vibration - Isolation Pads - Compression Shear on the Small Parts and Bearings website.


Mounts - Vibration - Isolation Pads - General Purpose
Mounts - Vibration - Isolation Pads - General Purpose

Also see combined categories:
All Isolation Pad Mounts

For installation of industrial machinery where the ratio of shear loads to vertical loads is less than or equal to 1 to 5.

Base is unthreaded. The stud rests on the pad and is not threaded in or fastened to the pad. Self aligning feature compensates for uneven floors without sacrificing stability. Scientifically designed diamond suction cells of the neoprene insert firmly anchor the machine to the floor. Recommended for a wide range of industrial machinery and equipment where simple precise leveling is required. 25.4mm level adjustment.

Related Information:

There is also a good range of Mounts - Vibration - Isolation Pads - General Purpose on the Small Parts and Bearings website.


Mounts - Base - Neoprene - Style 2
Mounts - Base - Neoprene - Style 2

Also see combined categories:
All Neoprene Base Mounts


Related Information:

There is also a good range of Mounts - Base - Neoprene - Style 2 on the Small Parts and Bearings website.


Mounts - Bonded
Mounts - Bonded

Also see combined categories:
All Bonded Mounts


Related Information:

There is also a good range of Mounts - Bonded on the Small Parts and Bearings website.


Mounts - Bonded - Two Piece
Mounts - Bonded - Two Piece

Also see combined categories:
All Bonded Mounts

Steel insert overcoated with rubber joins the two pieces.

Related Information:

There is also a good range of Mounts - Bonded - Two Piece on the Small Parts and Bearings website.


Mounts - Centre Bolt - Solo Unitised
Mounts - Centre Bolt - Solo Unitised

Also see combined categories:
All Centrebolt Mounts

Vibration dampening. Also known as T Bushes or Bonded Mounts.

Calculate static load and select a mount of equal or greater capacity. For dynamic loads of 3 x static load select the next larger size. Lubricate mount and socket with water or rubber lubricant. Insert into socket and hand rotate with axial force. Outer Body : Natural Rubber / Spacer : Rolled Tubular Steel.

Related Information:

There is also a good range of Mounts - Centre Bolt - Solo Unitised on the Small Parts and Bearings website.


Mounts - Cone - Delrin
Mounts - Cone - Delrin



Related Information:

There is also a good range of Mounts - Cone - Delrin on the Small Parts and Bearings website.


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 125086 products in 2457 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 125086 products in 2457 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.