Miniature Bearings Australia Pty Ltd

Covid-19 Update!! Current supply status.

Trading by online order and email.
Outbound Deliveries: Allow a few extra days within Australia and extra 7 days for overseas deliveries.
Pre-orders and Backorders: Allow extra 7 days due to quarantine precautions.
Distributors: Most MBA distributors are open and able to contact us using the distributor phone line.

Hospitals, medical equipment repairs and manufacture and bio research teams please email us if you need emergency contacts for equipment spare parts.

Attachments Stop Sleeves Categories


Cable


Attachments - Stop Sleeves
Attachments - Stop Sleeves


Use with synchromesh or standard miniature cable


Related Information:

There is also a good range of Attachments - Stop Sleeves on the Small Parts and Bearings website.


Attachments - Loop Sleeves
Attachments - Loop Sleeves


Use with synchromesh or standard miniature cable


Related Information:

There is also a good range of Attachments - Loop Sleeves on the Small Parts and Bearings website.


Attachments - Eyes - Synchromesh
Attachments - Eyes - Synchromesh

Also see combined categories:
All Synchromesh Attachments

Use with synchromesh or standard miniature cable

Recommended dimensions after crimping:. 1.05 Cable - A=2.59. 2.06 Cable - A=2.64. 2.60 Cable - A=2.72. 3.40 Cable - A=2.80 (3.40 Cable must have outer helical wire removed prior to crimping).

Related Information:

There is also a good range of Attachments - Eyes - Synchromesh on the Small Parts and Bearings website.


Attachments - Thimbles - Carbon Steel
Attachments - Thimbles - Carbon Steel


Hot galvanised carbon steel. Use with synchromesh or standard miniature cable

Meets USA Fed. Spec. FF-T-276b for Type III thimbles.

Related Information:

There is also a good range of Attachments - Thimbles - Carbon Steel on the Small Parts and Bearings website.


Attachments - Thimbles - Stainless Steel
Attachments - Thimbles - Stainless Steel


316 Stainless Steel. Use with synchromesh cable or standard miniature cable. Use with synchromesh or standard miniature cable

Thimbles provide loop support at higher loads and protect cables from wear when motion is present. Some thimbles may have open or uneven ends.

Related Information:

There is also a good range of Attachments - Thimbles - Stainless Steel on the Small Parts and Bearings website.


Attachments - Threaded Plugs
Attachments - Threaded Plugs


Use with synchromesh or standard miniature cable

F and L dimensions are obtained after swaging. Before swaging the fitting is round.

Related Information:

There is also a good range of Attachments - Threaded Plugs on the Small Parts and Bearings website.


Attachments - Wire Rope Clips - Carbon Steel
Attachments - Wire Rope Clips - Carbon Steel

Also see combined categories:
All Wire Rope Clips

Hot galvanised carbon steel

Furnished with hex nuts. Meet USA Fed. Spec. FF-C-450c, Type I, Class 1.

There is also a good range of Attachments - Wire Rope Clips - Carbon Steel on the Small Parts and Bearings website.


Attachments - Wire Rope Clips - Stainless Steel
Attachments - Wire Rope Clips - Stainless Steel

Also see combined categories:
All Wire Rope Clips

304 Stainless Steel

Furnished with hex nuts. Meet USA Fed. Spec. FF-C-450c, Type I, Class 1.

There is also a good range of Attachments - Wire Rope Clips - Stainless Steel on the Small Parts and Bearings website.


Knobs - Lever - Through Bore
Knobs - Lever - Through Bore

Also see combined categories:
All Levers
All Knobs

Lever knobs with moulded female threads, ideal for direct attachment to operating levers. Plastic (high grade gloss black phenolic) with Steel insert. Temperature Range: -30oC to +140oC. All knobs are fitted with a brass female insert.

Related Information:

There is also a good range of Knobs - Lever - Through Bore on the Small Parts and Bearings website.


RC Spare Parts - Hangar9
RC Spare Parts - Hangar9


Hangar Nine airplane parts listed by description. Parts to suit Alpha 40, Corsair, Cessna, Edge 540, Extra 260, Hellcat, Funtana, J3 Cub, P-40 Warhawk, P-47, P-51 Mustang, Piper Pawnee, Sopwith Camel, Spitfire, Sukhoi SU-26, T-34 Mentor

Includes control line, handle and attachments.

There is also a good range of RC Spare Parts - Hangar9 on the Small Parts and Bearings website.


Sleeves - Hex Hole - Carbon Steel
Sleeves - Hex Hole - Carbon Steel

Also see combined categories:
All Hex Hole Sleeves

Carefully turned to provide 0.076mm (0.003in) concentricity ID to OD. Round OD with with a uniform hex hole broached from one end to the other.


There is also a good range of Sleeves - Hex Hole - Carbon Steel on the Small Parts and Bearings website.


Sleeves - Hex Hole - Hardened
Sleeves - Hex Hole - Hardened

Also see combined categories:
All Hex Hole Sleeves

Pre hardened to Rockwell 23-30C. Carefully turned to provide 0.076mm (0.003in) concentricity ID to OD. Round OD with with a uniform hex hole broached from one end to the other.


There is also a good range of Sleeves - Hex Hole - Hardened on the Small Parts and Bearings website.


Sleeves - Square Hole - Plain - Carbon Steel
Sleeves - Square Hole - Plain - Carbon Steel

Also see combined categories:
All Square Hole Sleeves

Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through.


There is also a good range of Sleeves - Square Hole - Plain - Carbon Steel on the Small Parts and Bearings website.


Sleeves - Square Hole - Plain - Hardened
Sleeves - Square Hole - Plain - Hardened

Also see combined categories:
All Square Hole Sleeves

Pre hardened to Rockwell 23-30C. Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through.


There is also a good range of Sleeves - Square Hole - Plain - Hardened on the Small Parts and Bearings website.


Sleeves - Square Hole - Threaded - Carbon Steel
Sleeves - Square Hole - Threaded - Carbon Steel

Also see combined categories:
All Square Hole Sleeves

Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through and threaded internally at one end.


There is also a good range of Sleeves - Square Hole - Threaded - Carbon Steel on the Small Parts and Bearings website.


Couplings - Sleeve Type - Hubs
Couplings - Sleeve Type - Hubs


0.05 to 2.1 Nm. Max Speed 1750 rpm.

Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.

Related Information:

There is also a good range of Couplings - Sleeve Type - Hubs on the Small Parts and Bearings website.


Couplings - Sleeve Type - Sleeves
Couplings - Sleeve Type - Sleeves


0.05 to 2.1 Nm. Max Speed 1750 rpm.

Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.

Related Information:

There is also a good range of Couplings - Sleeve Type - Sleeves on the Small Parts and Bearings website.


Shaftloc-tm Sleeves - Single Ended
Shaftloc-tm Sleeves - Single Ended

Also see combined categories:
All Shaftloc

Simple effective way to lock components onto shafts.

416 Stainless Steel. Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened.

Related Information:

There is also a good range of Shaftloc-tm Sleeves - Single Ended on the Small Parts and Bearings website.


Sealing Plugs - Stainless Sleeve with Hardened Ball
Sealing Plugs - Stainless Sleeve with Hardened Ball


The sealing plug is a safe, quick, leakproof and low cost method for sealing cross-drilled holes. It ensures peak performance with a comfortable safety margin even in extreme applications.

Sleeve: Stainless Steel DIN 1.4305, AISI 303. Ball: Bearing Steel, Heat Treated. Hardness: HB = 220.

There is also a good range of Sealing Plugs - Stainless Sleeve with Hardened Ball on the Small Parts and Bearings website.


Couplings - Geargrip - Precision - Sleeves Only
Couplings - Geargrip - Precision - Sleeves Only


Match with hubs from hubs category


Related Information:

There is also a good range of Couplings - Geargrip - Precision - Sleeves Only on the Small Parts and Bearings website.


Rollers - Feed - With Aluminium Sleeve
Rollers - Feed - With Aluminium Sleeve

Also see combined categories:
All Rollers

Tolerance of Roller Outside Diameter (D) is +/-0.075 mm

Urethane 60 Durometer ground outside diameter. Aluminium sleeve. Feed rollers do not have a rotating bore. They are designed to turn with the shaft.

Related Information:

There is also a good range of Rollers - Feed - With Aluminium Sleeve on the Small Parts and Bearings website.


Couplings - Crowned Tooth Gear - Sleeve Only
Couplings - Crowned Tooth Gear - Sleeve Only


Match with hubs from the hubs category

+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.

Related Information:

There is also a good range of Couplings - Crowned Tooth Gear - Sleeve Only on the Small Parts and Bearings website.


Bearings - Needle Roller - Inner Rings
Bearings - Needle Roller - Inner Rings


Hardened sleeves for needle roller bearings.


Related Information:

There is also a good range of Bearings - Needle Roller - Inner Rings on the Small Parts and Bearings website.


Couplings - Geargrip - Precision - Hubs Only
Couplings - Geargrip - Precision - Hubs Only


Match with sleeves from sleeves category


Related Information:

There is also a good range of Couplings - Geargrip - Precision - Hubs Only on the Small Parts and Bearings website.


Couplings - Crowned Tooth Gear - Hubs Only
Couplings - Crowned Tooth Gear - Hubs Only


Match with sleeves from the sleeves category

+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.

Related Information:

There is also a good range of Couplings - Crowned Tooth Gear - Hubs Only on the Small Parts and Bearings website.


Rod Ends - Steel - Studded - Quick Disconnect - Female
Rod Ends - Steel - Studded - Quick Disconnect - Female

Also see combined categories:
All Female Rod Ends with Stud

Joints are strength, quick disconnect assemblies with good wear characteristics. Retaining sleeve insures the assembly can only be put together with the sleeve positively aligned with the ball cavity. When spring is released, alignment is automatic thereby eliminating any possiblity of partial closure. Ball stud and Body are made of low carbon steel. Studs are surface hardened. All Parts are plated and dichromate treated.

There is also a good range of Rod Ends - Steel - Studded - Quick Disconnect - Female on the Small Parts and Bearings website.


Rollers - Urethane Feed - With Hub
Rollers - Urethane Feed - With Hub

Also see combined categories:
All Tyred OD Bearings
All Rollers

Urethane coated aluminium alloy feed rollers with hub.

Roller - Urethane 60 Durometer, Ground Outside Diameter. Sleeve - Aluminium.

Related Information:

There is also a good range of Rollers - Urethane Feed - With Hub on the Small Parts and Bearings website.


Latches - Compression - Lift and Turn - Straight Handle
Latches - Compression - Lift and Turn - Straight Handle


Lift handle to relax compression and then turn to open. Handle and sleeve are die cast zinc with either polished chrome or black powder coat finish.

Comes with mounting hardware. Max working load 44kg. M5 mounting screws supplied. For panels thicker than 6.35mm a longer screw and lockwasher combination will be required.

There is also a good range of Latches - Compression - Lift and Turn - Straight Handle on the Small Parts and Bearings website.


Collars - Shaft - Gripfast - ABS Plastic
Collars - Shaft - Gripfast - ABS Plastic

Also see combined categories:
All Round Bore Shaft Collars

Self Locking - Quick Release.

265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs.

Related Information:

There is also a good range of Collars - Shaft - Gripfast - ABS Plastic on the Small Parts and Bearings website.


Rollers - Urethane - Lengths
Rollers - Urethane - Lengths

Also see combined categories:
All Tyred OD Bearings
All Rollers

Low cost alternative for making your own wheels, castors, rollers, sheaves etc. Urethane rod with dual hardness. Harder inner sleeve with softer outside for use as a roller.

Blue outer tyre 90A Durometer bonded to a hard brown 75D Durometer inner sleeve. This results in a hard anti friction bearing surface inside with a soft tyre outside. The roller can be cut and machined to suit your purposes. Testing for your application is recommended.

Related Information:

There is also a good range of Rollers - Urethane - Lengths on the Small Parts and Bearings website.


Plungers - Ball - Push Fit - 303 Stainless Steel
Plungers - Ball - Push Fit - 303 Stainless Steel

Also see combined categories:
All Push Fit Ball Plungers

Unthreaded

Body BSD: Pom (Delrin) BSD-SS: W.-Nr 1.4305 (303) Stainless Steel. Sleeve BSD: Thermoplastic BSD-SS: Stainless Steel. Ball: W.-Nr 1.4034 (420) Stainless Steel. Spring: W.-Nr 1.4310 (301) Stainless Steel. Surface Finish BSD: Ball hardened, bright BSD-SS: Bright.

There is also a good range of Plungers - Ball - Push Fit - 303 Stainless Steel on the Small Parts and Bearings website.


Plungers - Ball - Push Fit - Plastic Body - Plastic Ball
Plungers - Ball - Push Fit - Plastic Body - Plastic Ball

Also see combined categories:
All Push Fit Ball Plungers

Unthreaded. Plastic body and ball.

Body BSD: Pom (Delrin) BSD-SS: W.-Nr 1.4305 (303) Stainless Steel. Sleeve BSD: Thermoplastic BSD-SS: Stainless Steel. Ball: W.-Nr 1.4034 (420) Stainless Steel. Spring: W.-Nr 1.4310 (301) Stainless Steel. Surface Finish BSD: Ball hardened, bright BSD-SS: Bright.

There is also a good range of Plungers - Ball - Push Fit - Plastic Body - Plastic Ball on the Small Parts and Bearings website.


Pulleys - Timing - 3.000mm Pitch - HTD - 9mm Wide - Plastic - Hubless
Pulleys - Timing -  3.000mm Pitch - HTD - 9mm Wide - Plastic - Hubless

Also see combined categories:
All 3mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit HTD 3.000mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide. Moulded single or double flange. No hub.

Suitable for use with shaftloc sleeves.

Related Information:

There is also a good range of Pulleys - Timing - 3.000mm Pitch - HTD - 9mm Wide - Plastic - Hubless on the Small Parts and Bearings website.


Stops - Spring - Flat Button
Stops - Spring - Flat Button

Also see combined categories:
All Spring Stops

Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is case hardened low carbon steel. Properly radiused nose for perfect fit with no wobble. Aluminium body.


There is also a good range of Stops - Spring - Flat Button on the Small Parts and Bearings website.


Stops - Spring - Flat Face
Stops - Spring - Flat Face

Also see combined categories:
All Spring Stops

Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is case hardened low carbon steel. Properly radiused nose for perfect fit with no wobble. Aluminium body.


There is also a good range of Stops - Spring - Flat Face on the Small Parts and Bearings website.


Stops - Spring - Flat Face - With Tang
Stops - Spring - Flat Face - With Tang

Also see combined categories:
All Spring Stops

Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is case hardened low carbon steel. Properly radiused nose for perfect fit with no wobble. Aluminium body.

Tang prevents thin gauge material from sliding under plunger.

There is also a good range of Stops - Spring - Flat Face - With Tang on the Small Parts and Bearings website.


Stops - Spring - Round Acetal Nose
Stops - Spring - Round Acetal Nose

Also see combined categories:
All Spring Stops

Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is hardened and ground smooth. Properly radiused nose for perfect fit with no wobble. Aluminium body.


There is also a good range of Stops - Spring - Round Acetal Nose on the Small Parts and Bearings website.


Stops - Spring - Round Steel Nose
Stops - Spring - Round Steel Nose

Also see combined categories:
All Spring Stops

Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is hardened and ground smooth. Properly radiused nose for perfect fit with no wobble. Aluminium body.


There is also a good range of Stops - Spring - Round Steel Nose on the Small Parts and Bearings website.


Shock Absorbers - Stop Collars
Shock Absorbers - Stop Collars

Also see combined categories:
All Shock Absorbers


There is also a good range of Shock Absorbers - Stop Collars on the Small Parts and Bearings website.


Shock Absorbers - Flanged Stop Collars
Shock Absorbers - Flanged Stop Collars

Also see combined categories:
All Shock Absorbers


Related Information:

There is also a good range of Shock Absorbers - Flanged Stop Collars on the Small Parts and Bearings website.


Shock Absorbers - Hydraulic - Stop Collars
Shock Absorbers - Hydraulic - Stop Collars

Also see combined categories:
All Shock Absorbers


There is also a good range of Shock Absorbers - Hydraulic - Stop Collars on the Small Parts and Bearings website.


Bumpers - Cylindrical - Male - Urethane
Bumpers - Cylindrical - Male - Urethane

Also see combined categories:
All Cylindrical Bumpers

Used to guard, stop, align, position and protect parts.


There is also a good range of Bumpers - Cylindrical - Male - Urethane on the Small Parts and Bearings website.


Bumpers - Elastomer - Low Energy Absorption - Longer Stroke - Soft Stop
Bumpers - Elastomer - Low Energy Absorption - Longer Stroke - Soft Stop

Also see combined categories:
All Elastomer Bumpers

Elastomer bumpers provide excellent resistance to chemicals and humidity. 20 times greater durability than urethane.

10 greater durability than rubber and 500 times greater than steel coiled springs. Maintains excellent resilience at extreme temperatures and remains flexible with no material degradation between -62 oC and +148 Deg C (-80 Deg F and +300 Deg F). Mounting screws not included.

There is also a good range of Bumpers - Elastomer - Low Energy Absorption - Longer Stroke - Soft Stop on the Small Parts and Bearings website.


Linear Track System - Crowned Roller
Linear Track System - Crowned Roller


Rails, rollers and end stops sold separately. Please choose your components from the listing.

Easy to use system is usually mounted on a vertical surface as a low cost linear motion solution. Hardened crown roller allows for self-alignment with good strength and long life. Rails are unistrut typeand are black powder coated. End stops prevent over travel and come with a mounting bolt. End stops are not designed to support loads. Maximum bearing load is 130 kg. Maximum bearing speed is 45 mtrs per minute.

There is also a good range of Linear Track System - Crowned Roller on the Small Parts and Bearings website.


Housings - Bearing - Tapped Base - Thermoplastic with Chrome Steel Bearing
Housings - Bearing - Tapped Base - Thermoplastic with Chrome Steel Bearing


Thermoplastic housed units offer a more favourable economic choice. Hard chrome inserts offer an intermediate level of corrosion resistance.

Operating temperature minus 20 oC to +95 deg C. Thermoplastic hosuings are offwhite and are made from glass reinforced PBT resin. Favourable chemical resistance. Very resistant to moisture absorption. Excellent mechanical, thermal and electrical properties. All sleeves, bushings and grease fittings are 300 grade stainless steel.

There is also a good range of Housings - Bearing - Tapped Base - Thermoplastic with Chrome Steel Bearing on the Small Parts and Bearings website.


Housings - Bearing - 2 Bolt Flange - Thermoplastic with Chrome Steel Bearing
Housings - Bearing - 2 Bolt Flange - Thermoplastic with Chrome Steel Bearing


Thermoplastic housed units offer a more favourable economic choice. Hard chrome inserts offer an intermediate level of corrosion resistance.

Operating temperature minus 20 oC to +95 deg C. Thermoplastic hosuings are offwhite and are made from glass reinforced PBT resin. Favourable chemical resistance. Very resistant to moisture absorption. Excellent mechanical, thermal and electrical properties. All sleeves, bushings and grease fittings are 300 grade stainless steel.

There is also a good range of Housings - Bearing - 2 Bolt Flange - Thermoplastic with Chrome Steel Bearing on the Small Parts and Bearings website.


Inserts - Rivet Nuts - Klik - Threadsert
Inserts - Rivet Nuts - Klik - Threadsert

Also see combined categories:
All Klik Rivet Nuts

Individual Inserts for use with the Klik Thread Setter Tool

These threaded inserts can be used in blind or through hole applications. Can be used in almost any material over 2.38mm thick. As the insert is installed the threaded section is completely swaged into the sleeve portion of the hole, permitting them to be used with grade 8 screws. The installation hole size is determined by the density of the parent material. Can be pressed or otherwise compressed manually with a hammer for quick installation jobs in sheet material. Tools are available for assembly in blind holes or production assembly. Email us for a price on tools.

There is also a good range of Inserts - Rivet Nuts - Klik - Threadsert on the Small Parts and Bearings website.


Slides - Linear - Non Recirculating Ball - Standard
Slides - Linear - Non Recirculating Ball - Standard

Also see combined categories:
All Linear Slides

The BSP precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.

Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100oC (Constant), +120oC (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants.

There is also a good range of Slides - Linear - Non Recirculating Ball - Standard on the Small Parts and Bearings website.


Slides - Drawer - Stainless - No Disconnect - Heavy Duty - 19mm Ext
Slides - Drawer - Stainless - No Disconnect - Heavy Duty - 19mm Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted two member slide. Positive stop slide that will not disconnect once installed. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).

There is also a good range of Slides - Drawer - Stainless - No Disconnect - Heavy Duty - 19mm Ext on the Small Parts and Bearings website.


Slides - Drawer - Stainless - No Disconnect - Medium Duty - 19mm Ext
Slides - Drawer - Stainless - No Disconnect - Medium Duty - 19mm Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted two member slide. Positive stop slide that will not disconnect once installed. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).

There is also a good range of Slides - Drawer - Stainless - No Disconnect - Medium Duty - 19mm Ext on the Small Parts and Bearings website.


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 125190 products in 2452 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Miniature Bearings Australia Pty Ltd (ABN 94 069 113 800)

Miniature Bearings Australia offers 125190 products in 2452 categories including ball bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, couplings, screws, socket cap, dental bearings, magnets, sprockets, timing belts and pulleys, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.