Categories that include the terms: WASHERS and SPRING
|
Washers |  |
Washers - Disc Spring - Carbon Steel (Relevance 10/10)
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093
|
Washers - Disc Spring - Plastic (Relevance 10/10)
Also known as belleville washers.
Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb® material.
|
Washers - Disc Spring - Stainless Steel (Relevance 10/10)
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093
|
Washers - Flat - Carbon Spring Steel - Precision (Relevance 10/10)
Flat Carbon Spring Steel Washers.
|
Washers - Lock - External Tooth - Spring Steel (Relevance 10/10)
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Internal Tooth - Spring Steel (Relevance 10/10)
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
|
Washers - Spring (Relevance 10/10)
Wave Washers - All Materials.
|
Air Springs | |
Springs - Air - Convolute Bellows (Relevance 7/10)
|
Bearings - Thrust | |
Bearings - Thrust - Ball - Washers Only (Relevance 7/10)
Hardened thrust washers for thrust bearings - ungrooved. Match with thrust ball and retainer or roller type.
Stainless Steel Washers are hardened to HRC38.42. Carbon Steel Washers are hardened to RC59.61.
|
Castors | |
Ball Transfer Units - Spring Loaded (Relevance 7/10)
For conveying materials. From miniature to large.
Case: Zinc plated Mild Steel. Ball: Carbon Steel 60-66 HRC. Applications: - Guillotines - Presses - Moulding machines - Base of machines for easy handling - Press brakes - Shock loading.
|
Clutches and Brakes | |
Clutches - Slip - Spring Wrapped (Relevance 7/10)
|
Couplings | |
Couplings - Slip - Spring Wrapped (Relevance 7/10)
Tension control - transmission overload protection. 0.035 to 1.69 Nm.
Coupling is sliped over one shaft and screws tightened. Second shaft is inserted into other end. Loose end of coupling is pulled back about 0.5mm then screws tightened. Serves as a torque limiter as well as a coupling. Long life under continuous slip applications.
|
Fasteners | |
Joints - Clevis - Spring Clips (Relevance 7/10)
Made from 9SMn steel.
Steel 9 SMn 28K (550-700 N/mm2). See also yokes.
|
Nuts - Hexagonal - Washer Faced - Titanium (Relevance 7/10)
6AL-4V (Grade 5) High strength titanium alloy.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. 6AL-4V (Grade 5) High strength titanium alloy, used in critical aircraft structural components. UNS R56400.
|
Screws - Thumb - Washer (Relevance 7/10)
Brass, steel, aluminum and stainless.
|
Materials | |
Wire - Steel - Spring - Music Wire (Relevance 7/10)
SAE 1090 Spring Steel.
Shipped in straight lengths on wood backing board.
|
Mounts and Vibration Control | |
Dampeners - Spring - Silicone (Relevance 7/10)
Damps low frequency vibrations.
Studs: Steel / Body : Silicone Gel / Spring : Piano Wire Type B Nickel Plated. Vertical vibrations damped without horizontal deflection. Compression only. Outstanding shock absorbing ability.
|
Mounts - Spring - Damped (Relevance 7/10)
Temp Range: -70 to 175 Deg C (-94 to 347 Deg F).
Lateral to vertical stiffness approx. 1:1 / Must be loaded vertically through its axis. Elastic limit corresponds to a maximum load in compression of 1.2 g (0.042oz) and radially 0.2 g (0.007oz). Damping factor c/co 0.15 to 0.20. Base Plate: Mild Steel / Springs: High Tensile Steel - Phosphated and dyed black. Isolator: Knitted stainless steel mesh / End Caps: Light Alloy.
|
Mounts - Spring - Suspension - Pedestal (Relevance 7/10)
Cadmium plated steel. Temp Range : -60 to 150 Deg C (-76 to 302 Deg F).
|
Mounts - Spring - Suspension - Single Hole (Relevance 7/10)
Cadmium plated steel. Temp Range : -60 to 150 Deg C (-76 to 302 Deg F).
|
Mounts - Spring - Suspension - Square Plate (Relevance 7/10)
All metal.
|
Reels | |
Reels - Spring Powered - Arbor Mounted (Relevance 7/10)
Mounting studs sold seperately.
Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture. Mounting studs sold seperately.
|
Reels - Spring Powered - Base Mounted - Plastic Case (Relevance 7/10)
Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture.
|
Reels - Spring Powered - Base Mounted - Steel (Relevance 7/10)
Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture.
|
Reels - Spring Powered - Bracket Mounted (Relevance 7/10)
Applications: Counterbalances, door closers, cable retractors. Applications: Hose retreivers, tool head returns, cabinets and furniture.
|
Springs | |
Gas Springs - Adjustable - 50-540N (Relevance 7/10)
Body: Semi Matt Black Epoxy Paint. Finish: Black. Adjusted by Grubscrew. Once discharged, the gas is not refillable. Supplied filled to maximum force.
|
Gas Springs - Adjustable - Accessories (Relevance 7/10)
See diagrams in main Gas Springs Categories.
|
Gas Springs - Adjustable - Push Type - Max 100N (Relevance 7/10)
Piston Rod: Hard black ceramic finish. Body: Powder Coated. End Fittings: Zinc Plated Steel. Operating Temp. Range: -20°C to +80°C End Position Damping Length: Approx. 5mm. Available Force Range: 5N to 100N (comes standard with max. force).
|
Gas Springs - Adjustable - Push Type - Max 180N (Relevance 7/10)
Piston Rod: Hard black ceramic finish. Body: Powder Coated. End Fittings: Zinc Plated Steel. Operating Temp. Range: -20°C to +80°C End Position Damping Length: Approx. 10mm. Available Force Range: 10N to 180N (comes standard with max. force).
|
Gas Springs - Adjustable - Push Type - Max 400N (Relevance 7/10)
Piston Rod: Hard black ceramic finish. Body: Powder Coated. End Fittings: Zinc Plated Steel. Operating Temp. Range: -20°C to +80°C End Position Damping Length: Approx. 10mm. Available Force Range: 10N to 400N (comes standard with max. force).
|
Gas Springs - Adjustable - Push Type - Max 700N (Relevance 7/10)
Piston Rod: Hard black ceramic finish. Body: Powder Coated. End Fittings: Zinc Plated Steel. Operating Temp. Range: -20°C to +80°C End Position Damping Length: Approx. 10mm. Available Force Range: 50N to 700N (comes standard with max. force).
|
Gas Springs - Adjustable - Push Type - Max 1300N (Relevance 7/10)
Piston Rod: Hard black ceramic finish. Body: Powder Coated. End Fittings: Zinc Plated Steel. Operating Temp. Range: -20°C to +80°C End Position Damping Length: Approx. 10mm. Available Force Range: 80N to 1300N (comes standard with max. force).
|
Gas Springs - Adjustable - Push Type - Max 2600N (Relevance 7/10)
Piston Rod: Hard black ceramic finish. Body: Powder Coated. End Fittings: Zinc Plated Steel. Operating Temp. Range: -20°C to +80°C End Position Damping Length: Approx. 10mm. Available Force Range: 100N to 2600N (comes standard with max. force).
|
Gas Springs - Adjustable - Push Type - Max 5000N (Relevance 7/10)
Piston Rod: Hard black ceramic finish. Body: Powder Coated. End Fittings: Zinc Plated Steel. Operating Temp. Range: -20°C to +80°C End Position Damping Length: Approx. 10mm. Available Force Range: 500N to 5000N (comes standard with max. force).
|
Gas Springs - Adjustable Force (Relevance 7/10)
|
Gas Springs - Assembly End Fittings (Relevance 7/10)
|
Gas Springs - Econoloc (Relevance 7/10)
|
Gas Springs - End Fittings (Relevance 7/10)
|
Gas Springs - Fixed Force (Relevance 7/10)
|
Indent Blocks (Relevance 7/10)
Indent Blocks: Hardened black oxide sintered steel. Used together with spring plungers for detenting or positioning sliding parts, flaps or for similar applications.
|
Plungers - Spring - Smooth (Relevance 7/10)
Stainless Steel or Plastic - No Thread.
Body BSD: Pom (Delrin) BSD-SS: W.-Nr 1.4305 (303) Stainless Steel. Sleeve BSD: Thermoplastic BSD-SS: Stainless Steel. Ball: W.-Nr 1.4034 (420) Stainless Steel. Spring: W.-Nr 1.4310 (301) Stainless Steel. Surface Finish BSD: Ball hardened, bright BSD-SS: Bright.
|
Plungers - Spring - Smooth - Double Ended (Relevance 7/10)
|
Plungers - Spring - Striker Bushings (Relevance 7/10)
Use with ball or bolt spring plungers for a hard wearing contact area.
Burnished ground hardened steel.
|
Plungers - Spring - Threaded (Relevance 7/10)
Items shown with Long-Lok have a dry threadlocking sealant applied to thread.
|
Plungers - Spring - Threaded - With Limit Switch (Relevance 7/10)
Supply Cable : Grey Two Phase for normally open contacts, black for normally closed. Temp (Body): -40 deg C to 170 deg C Temp (Cable): -10 deg C to 50 deg C. Electrical Supply : 20 mA DC / 50 mA DC. Voltage : 24V Supply Cable 2.8mm - 2 Phase. Safety Standard : IP40 Average Switch Life Span : 56 Switching.
|
Posts - Spring (Relevance 7/10)
|
Shock Absorbers - Adjustable (Relevance 7/10)
|
Shock Absorbers - Adjustable - Miniature (Relevance 7/10)
|
Shock Absorbers - Flanged Stop Collars (Relevance 7/10)
|
Shock Absorbers - Full Threaded - Adjustable (Relevance 7/10)
|
Shock Absorbers - Full Threaded - Clevis Mounts (Relevance 7/10)
|
Shock Absorbers - Full Threaded - Low Velocity Adjustable (Relevance 7/10)
|
Shock Absorbers - Full Threaded - Soft Contact/Self-Compensating (Relevance 7/10)
|
Shock Absorbers - Hydraulic - Adjustable - Small (Relevance 7/10)
|
Shock Absorbers - Hydraulic - Adjustable - Double Acting (Relevance 7/10)
|
Shock Absorbers - Hydraulic - Adjustable - Low Profile (Relevance 7/10)
|
Shock Absorbers - Hydraulic - Flanges (Relevance 7/10)
|
Shock Absorbers - Hydraulic - Hex Jam Nuts (Relevance 7/10)
|
Shock Absorbers - Hydraulic - Lock Rings (Relevance 7/10)
|
Shock Absorbers - Hydraulic - Self-Compensating (Relevance 7/10)
|
Shock Absorbers - Hydraulic - Stop Collars (Relevance 7/10)
|
Shock Absorbers - Hydraulic Speed/ Feed Controller (Relevance 7/10)
|
Shock Absorbers - Lock Nuts (Relevance 7/10)
|
Shock Absorbers - Mounting Blocks (Relevance 7/10)
|
Shock Absorbers - Ondrives (Relevance 7/10)
Body: Steel with black oxide finish, Stainless Steel or Chrome plated piston rod. Operating Temperature Range: -10°C to +70°C. Important: Provide mechanical stop 0.5mm before end of stroke.
|
Shock Absorbers - Ondrives - Accessories (Relevance 7/10)
|
Shock Absorbers - Self-Compensating (Relevance 7/10)
|
Shock Absorbers - Soft Contact/Self-Compensating (Relevance 7/10)
|
Shock Absorbers - Stop Collars (Relevance 7/10)
|
Spring Assemblies - Bracket - RINO (Relevance 7/10)
Spring: Stainless Steel 301 S21 Grade. Bobbin and Bracket: Nylon Moulded secured to aluminium sheet. Constant force extension springs provide a huge range of application opportunities. Springs can be extended in excess of 50 times the relaxed length of the spring. End holes are centred at the distances and diameters shown in the tables.
|
Spring Assemblies - Single - RINO (Relevance 7/10)
Spring: Stainless Steel 301 S21 Grade. Other Parts: Pressed Mild Steel, Zinc Plate and clear passivated. Temp Max 200 Deg C / Min -200 Deg C. Constant force extension springs provide a huge range of application opportunities. Springs can be extended in excess of 50 times the relaxed length of the spring.
|
Spring Assemblies - Small Bracket - RINO (Relevance 7/10)
Spring: Stainless Steel 301 S21 Grade. Base: Aluminium Drum: High Impact Styrine. Constant force extension springs provide a huge range of application opportunities. Springs can be extended in excess of 50 times the relaxed length of the spring.
|
Spring Assemblies - Twin - RINO (Relevance 7/10)
Spring: Stainless Steel 301 S21 Grade. Other Parts: Pressed Mild Steel, Zinc Plate and clear passivated. Temp Max 200 Deg C / Min -200 Deg C. Constant force extension springs provide a huge range of application opportunities. Springs can be extended in excess of 50 times the relaxed length of the spring.
|
Spring Motor Assemblies - Open - RINO (Relevance 7/10)
Budget Assemblies. Average fatigue life of 5000 to 30000 cycles.
Springs : 301 Stainless Steel. Average fatigue life of 5,000 to 30,000 cycles.
|
Spring Motor Assemblies - SDP (Relevance 7/10)
Base Mounted.
Base Mounted. Springs : 301 Stainless Steel.
|
Spring Motors - RINO (Relevance 7/10)
301 stainless Steel. Shipped as shown to be mounted on drums (not supplied) of the recommended diameters. Torque ratings listed are for the unwinding portion of the cycle. Torque at fully wound end of cycle will be slightly higher.
|
Spring Motors - SDP (Relevance 7/10)
301 stainless Steel. Shipped as shown to be mounted on drums (not supplied) of the recommended diameters. Torque ratings listed are for the unwinding portion of the cycle. Torque at fully wound end of cycle will be slightly higher.
|
Springs - Compression - Conical (Relevance 7/10)
Conical 302 Stainless steel springs
Solid height lower than a standard compression spring due to the conical shape Ends are closed Starting rate is the same as the kg/mm rate
|
Springs - Compression - Metre Lengths (Relevance 7/10)
Music wire to Din 17223 Class C. No. 1,1200. Stainless Steel wire to Din 17224 No. 1,4310.
|
Springs - Compression - Standard (Relevance 7/10)
Standard springs may or may not be supplied with ends ground flush. If the end type is important to your application please contact us for more information or a special quote.
|
Springs - Constant Force (Relevance 7/10)
Mounting hole specifications will be supplied on request. Free ID may vary to meet load specification.
|
Springs - Die (Relevance 7/10)
High tensile strength chromium alloy steels. Heat Resistance: Up to +230°C (Loss of load occurs above +120°C). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length.
|
Springs - Extension (Relevance 7/10)
Zinc Plated Spring Steel not recommended for applications exceeding 121 Deg C (250 Deg F). 302 Stainless springs not recommended for applications exceeding 260 Deg C (500 Deg F). 302 stainless steel is slightly magnetic.
|
Springs - Extension - Metre Lengths (Relevance 7/10)
Music wire to Din 17223 Class C. No. 1,1200. Stainless Steel wire to Din 17224 No. 1,4310.
|
Springs - Torsion - Anti Backlash (Relevance 7/10)
|
Springs - Torsion - Left Hand Wound (Relevance 7/10)
Left Hand Wound. 180 Deg. Deflection. Right hand wound and special springs are available on special order.
|
Springs - Torsion - Right Hand Wound (Relevance 7/10)
Right Hand Wound.
|
Washers | |
Washers - Cup - Brass (Relevance 7/10)
For countersunk screws.
Nickel Plated Brass.
|
Washers - Cup - Stainless Steel (Relevance 7/10)
For countersunk screws.
Stainless Steel cup washers.
|
Washers - Disk Lock (Relevance 7/10)
Stainless Grade Grade A2 302/316 18-8. Vibration-proof self tightening structural locking device. Maximum Working Temp: +430°C. DISC-LOCK® has outperformed all other types of loose, washered, threaded or pinned systems. in a wide range of high stress, corrosive, and vibration sensitive applications.
|
Washers - Finishing (Relevance 7/10)
|
Washers - Flat - Aluminium (Relevance 7/10)
Flat washers.
|
Washers - Flat - Brass - Commercial (Relevance 7/10)
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Flat - Brass - Precision (Relevance 7/10)
Precision Tolerances. Laminated brass shim washers.
|
Washers - Flat - Commercial - All Types (Relevance 7/10)
Includes all materials listed in other commercial washer categories.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Flat - Fibre (Relevance 7/10)
Flat fibre washers.
|
Washers - Flat - High Tensile (Relevance 7/10)
ASTM F436 1985. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
|
Washers - Flat - Mild Steel (Relevance 7/10)
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Flat - Nylon (Relevance 7/10)
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Flat - PTFE (Relevance 7/10)
Teflon Washers
|
Washers - Flat - PVC (Relevance 7/10)
Flat washers.
|
Washers - Flat - Precision - All Types (Relevance 7/10)
Includes all materials listed in other precision washer categories.
|
Washers - Flat - Rubber (Relevance 7/10)
|
Washers - Flat - Sintered Bronze - Precision (Relevance 7/10)
Flat washers from oil impregnated sintered bronze
|
Washers - Flat - Stainless Steel - Commercial (Relevance 7/10)
Flat washers.
Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
|
Washers - Flat - Stainless Steel - Precision (Relevance 7/10)
Precision Tolerances.
|
Washers - Flat - Titanium - CP Grade 1 (Relevance 7/10)
Flat washers. CP Grade 1 Titanium.
CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
|
Washers - Flat - Titanium - Grade 5 (Relevance 7/10)
Flat washers. 6AL-4V (Grade 5) High strength titanium alloy.
6AL-4V (Grade 5) High strength titanium alloy, used in critical aircraft structural components. UNS R56400. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
|
Washers - Lock - External Tooth - Stainless Steel (Relevance 7/10)
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Internal Tooth - Stainless Steel (Relevance 7/10)
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Split (Relevance 7/10)
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Tabbed - Heavy Duty (Relevance 7/10)
Heavy duty WH / TW Series for bearing locknuts.
Carbon spring steel. Use with NH series locknuts.
|
Washers - Lock - Tabbed - MB Series (Relevance 7/10)
Standard MB series lockwasher for use with bearing locknuts.
Carbon spring steel. Use with N/AN and NL series locknuts.
|
Washers - Lock - Tabbed - Thin (Relevance 7/10)
Thin section - use with NT series locknuts.
Use with NT series locknuts.
|
Washers - LockRite (Relevance 7/10)
Supplied in pairs.
|
Washers - Nord Lock (Relevance 7/10)
Supplied in pairs
Steel: Hardness HRA 75±3% (HRC48) Passivated Zinc Plated. ALWAYS LUBRICATE FASTENERS BEFORE REUSING. When reusing fasteners the friction is always higher. When tightening, a 20% higher torque should be applied than if tightening against a flat washer.
|
Washers - Safety (Relevance 7/10)
Spring Steel Hardened Black.
|
Washers - Self Aligning (Relevance 7/10)
AISI 303 Stainless Steel or Hardened steel 9 S Mn Pb 28 K DIN 6319. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3 Degree of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.
|
Washers - Shoulder - Nylon (Relevance 7/10)
|
Washers - Square (Relevance 7/10)
|
Kits | |
Assortment Kits - Various (Relevance 3/10)
Springs - O-Rings - Shafting - Circlips - Gears - Chain - Machine Keys - Nuts - Bolts - Screws - Washers - Roll Pins - Woodruff Keys - Cotter Pins - E-Clips - Fuses - Grease Nipples - Hitch Pins - Clevis Pins
|
Bearings - Thrust | |
Bearings - Thrust - Ball - Retainer and Balls Only (Relevance 1/10)
Match with thrust washers of the same bore and OD.
|
Bearings - Thrust - Roller (Relevance 1/10)
Washers and Rollers sold separately. Please select the appropriate washers (2) and roller assembly to complete a set.
Raceway hardness 58 HRC. Limiting Speeds are based on adequate oil lubrication. Load ratings are a guide taking into consideration ideal operating conditions. Dimensions given are nominal. Select the correct washer OD. Some washers listed here are to suit thrust ball bearings.
|
Bushings | |
Bushings - Tension (Relevance 1/10)
Like a heavy duty roll pin, dude.
Made of a high carbon spring steel with high elasticity, resilience and wear characteristics. Designed to replace solid steel tubular and cas hardened bushings because they are close tolerance, self-retaining and through hard. Insertion can be easily accomplished with a hammer and drift. Ideal for high load/low-speed operation in articulating or continuous applications.
|
Clamping and Locking | |
Collars - Shaft - Fastlock (Relevance 1/10)
No tools required.
Usable for Nonhardened Shafts. Inner body and Outer sleeve: 303 Stainless, Balls: 440C Stainless, Spring: 302 Stainless.
|
Collars - Shaft - Gripfast (Relevance 1/10)
Self Locking - Quick Release.
265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs.
|
Collars - Shaft - Stroke Adjustment (Relevance 1/10)
Recommended tolerances for mating shaft diameter : h6. Use with rubber washers listed under WASHERS.
|
Couplings | |
Couplings - Torque Tube (Relevance 1/10)
Internal compression spring preloads the ends against axial movement and backlash. Up to 2.8 Nm. Up to 2000 rpm.
Maximum Torque: 2.8 N.m (25 lb.in). Delrin Torque Tube. Aluminium Split Hubs. Do not compress the unit axially during installation. Speeds to 2000 rpm. One piece assembly.
|
Couplings - Uniflex (Relevance 1/10)
High speed to 30000 rpm. 2.3 to 9.27 Nm.
Spring : 1095 Steel Hubs : Cold Rolled Steel. Operating Temperature : 121 Deg C (250 Deg F). Maximum Speed : 30000 RPM. For CUF15 series the spring diameter is the same as the hub diameter.
|
Dental Products | |
Bearings and Oring kits for Dental Handpieces (Relevance 1/10)
Kits of Bearings - Orings - and Washers.
|
Fasteners | |
Nuts - Disk Locking (Relevance 1/10)
Body: Medium Carbon Steel (1035/45) HRC 26-34. Plating: Zinc ASTM B - 633. Free Spinning (no thread interference) (H6 Tolerance) - One piece assembly - No washer required. Installed with standard equipment, no special tools required - Easy to remove - Reusable. Can be used with Grade 5 (Class 8.8), Grade 8 (Class 10.9) and even stronger bolted.
|
Nuts - Hexagonal - Binx (Relevance 1/10)
Manufactured from A2 302/304 grade stainless steel. The standard Binx's entire locking action is contained within the nut body which is no thicker than a standard full nut. The ingenious design incorporates two opposing cantilever type springs which lock onto the bolt with inward and downward pressure. May be removed and placed repeatedly with minimum thread wear.
|
Nuts - Hexagonal - Locking (Relevance 1/10)
By applying torque to the locking screw, a press fit or wave spring effect is created locking female threads of the locknut to the male threads of the shaft.
Produces a strong metal to metal lock. Locking set screws do not protrude through the face of the threads of the locknut, eliminating damage to shaft.
|
Nuts - Lock - For Bearings - Metric AN Series (Relevance 1/10)
N / AN series locknuts.
Use with W series lockwashers.
|
Nuts - Lock - For Bearings - Metric KM Series (Relevance 1/10)
Use with MB series lockwashers.
|
Pins - Clevis - Self Locking (Relevance 1/10)
No need for cotter pins
Self locking and reusable with a spring loaded ball lock Plated steel with stainless steel ball
|
Pins - Dowel Bushings (Relevance 1/10)
Spring Steel. Precision rolled bushes manufactured from spring steel. Designed to eliminate the need for separate dowling where two components are to be located accurately together and fastened with bolts. They are available for use with bolts from M5 to M12.
|
Pins - Hammer Drive - Flat Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Pins - Hammer Drive - Round Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Pins - Roll - Plain (Relevance 1/10)
Plain carbon spring steel DIN1481.
|
Pins - Roll - Zinc Plated (Relevance 1/10)
Zinc plated spring steel DIN1481.
|
Hinges | |
Hinges - Flexi-Hinge - Precision (Relevance 1/10)
Double and Single Ended - Limited Angle Rotary Applications.
Zero Backlash. Constant Spring Rate. No lubrication required. Self centering on removal of load. -53 to +176 Deg. Celsius operating temperature.
|
Housings with Integral Bearing | |
Housings - Bearing - Flanged - Bronze Bearing (Relevance 1/10)
±5° Static Alignment.
Bearing: Bronze SAE 840 (oil impregnated). Housing: Sintered Aluminium. Bearing Retainer: Outer retainer is steel (which is clinched into Aluminium housing) with a Nylon washer on first face. Apply appropriate factor of safety to the nominal loads and speeds specified. Mating shaft rec. Min. 100 HRB. Max surface finish 16 RMS. Rec. shaft clearance 0.013 - 0.038mm.
|
Levers | |
Levers - Safety Tension (Relevance 1/10)
Steel Parts: Quality class 5.8. Ball Knob: Black plastic. Surface Finish: Burnished. Press the handle down until the teeth are fully engaged. The object can now be clamped or released. Spring pressure releases the locking mechanism immediately, restoring the safety function (handle can be turned effortlessly).
|
Lifting | |
Hoist Rings - Centre Pull (Relevance 1/10)
Standard: Alloy Steel. Finish: Black Oxide (except washer). Washer: Zinc plated with clear conversion coating.
|
Mounts and Vibration Control | |
Mounting Plates - Conidrive (Relevance 1/10)
For mounting ends of Conidrive™ belting in reciprocating applications.
Aluminium Alloy. Supplied with socket head cap screws and internal lock washers.
|
Retaining Rings and Clips | |
Circlips - External - Grooveless (Relevance 1/10)
Includes MIL-R-21248/MS 90707 - Styles M1440 / Ellison GR / Seeger G and GA.
Reusable tapered section rings for grooveless shafts like plastics, tubes or castings. Can be used where adjustable ring placement is desired - like progressively tightening a compression spring.
|
Circlips - External - Inverted (Relevance 1/10)
N1408 / SHI / 16626 / 4100 / 5108 - Spring Steel and Stainless Steel.
Tapered section ring with lugs inverted on the ID to allow use in tight areas with minimal clearance. Less thrust load than standard circlips.
|
Spiral Rings - External - Heavy Duty (Relevance 1/10)
AHE / WSM / AS3216 / RSN / MIL-R-27426A2 - Spring Steel and Stainless Steel.
Heavy duty design for use with NAS669-670 deep grooves in applications like double row and tapered roller bearings. Requires no tools for removal. Equivalent to Associated Spring: AHE, Smalley: WSM, Spirolox and Ramsey: RSN, Aerospace: AS3216, MIL-R-27426A2
|
Spiral Rings - External - Light Duty (Relevance 1/10)
Includes series CE / VS / US - Spring Steel and Stainless Steel.
Light duty single turn rings used in low clearance applications. Also used as a positioning point for light loads. Radius notch on one end for removal. Narrow radial wall yields moderate thrust loads. Equivalent to Associated Spring: CE, Smalley: VS, Spirolox and Ramsey: US
|
Spiral Rings - External - Medium Duty (Relevance 1/10)
AE / WS / AS3218 / RS / MIL-R-27426A1 - Spring Steel and Stainless Steel.
Popular series that will accommodate light and medium bearing series thrust loads. Available in military and aerospace specifications. Equivalent to Associated Spring: AE, Smalley: WS, Spirolox and Ramsey: RS, Aerospace AS3218, MIL-R-27426A1
|
|
