Categories that include the terms: UNIVERSAL and JOINT
|
Universal Joints |  |
Covers - Universal Joint - Elasticate Rubber (Relevance 10/10)
For Single and Double Universal Joints.
-27 Deg C to 70 Deg C temp range (constant). -32 Deg C to 120 Deg C temp range (intermittent).
|
Covers - Universal Joint - Neoprene Rubber (Relevance 10/10)
For Single and Double Universal Joints.
-27 Deg C to 70 Deg C temp range (constant). -32 Deg C to 120 Deg C temp range (intermittent).
|
Universal Joints - Inverted Design (Relevance 10/10)
|
Universal Joints - Inverted Design - Telescoping (Relevance 10/10)
|
Universal Joints - Needle Roller - Low Backlash (Relevance 10/10)
Steel 9SMn Pb36K. Forged centre cross with hard ground ends for needle bearings (needle bearings sealed). Max. Speed: 4,000 Rpm. See techincal pages for torques at different speed and angles.
|
Universal Joints - Plastic (Relevance 10/10)
Acetal with or without steel inserts.
|
Universal Joints - Plastic with Brass Inserts - Ondrives (Relevance 10/10)
Cross Piece and Inserts: Brass CZ121 Chromate and passivate finish. Body - Black Acetal Max Speed: 1000 Rpm. Temp. Range: -20 Deg C to +60 Deg C. Backlash Free up to 1000,000,000 Turns.
|
Universal Joints - Steel (Relevance 10/10)
Steel - Cast Zinc - Stainless Steel.
|
Universal Joints - Telescoping - Moulded (Relevance 10/10)
|
Universal Joints - Telescoping - Spline Type - Needle Roller (Relevance 10/10)
Max Speed 4000 RPM.
Steel 9SMn Pb36K DIN808-W. Max. Working Angle - 60 Deg. Max. Speed 4000 RPM.
|
Universal Joints - Telescoping - Spline Type - Stainless Steel (Relevance 10/10)
Heat Resistant & Corrosion Resistant. MATERIAL: Joints - 303 Stainless Steel; Spline - 416 Stainless Steel. Max. Working Angle - 60 Deg. Pin Joints.
|
Universal Joints - Telescoping - Spline Type - Steel (Relevance 10/10)
Max Speed 800 rpm.
Steel 9SMn Pb36K DIN808-G. Max. Working Angle - 60 Deg. Max Speed 800 rpm.
|
Universal Joints - Telescoping - Steel - Hand Operated (Relevance 10/10)
Steel 9SMn Pb36K. Hand motion only. Unhardened Pins.
|
Universal Joints - Telescoping - Zero Backlash (Relevance 10/10)
|
Couplings | |
Couplings - Cross Joint (Relevance 7/10)
0.5 to 10 N.m. 3600 to 6000 rpm.
Bushings - Dry Bush Bearing. Stainless Steel Spacers. Steel Pins. Aluminium Alloy Hubs.
|
Fasteners | |
Joints - Ball and Socket - In-line (Relevance 7/10)
|
Joints - Ball and Socket - Right Angle (Relevance 7/10)
Steel Type: Zinc Passivated Induction Hardened. Stainless Steel Type: 303 Grade unhardened. Max. Static push/pull loads are valid for both radial and axial loads. Standard Steel type Ball Stud Tensile strength: Rm = 600 N/mm sq (Not applicable to stainless type). Standard Steel type Housing Tensile strength: Rm = 500 N/mm sq (Not applicable to stainless type).
|
Joints - Clevis - Plastic (Relevance 7/10)
Use with plastic rod ends - Includes pin and clip. See also yokes.
Comes with clevis pin and retaining clip. Corrosion Resistant, Lightweight. High Tensile Strength (Shown in table as Short Term / Long Term). Vibration Dampening / Noise Dampening. (1) Tensile Strengths shown are Maximum Static axial in Newtons.
|
Joints - Clevis - Spring Clips (Relevance 7/10)
Made from 9SMn steel.
Steel 9 SMn 28K (550-700 N/mm2). See also yokes.
|
Joints - Clevis - Stainless Steel (Relevance 7/10)
Stainless 1.4305 Stainless Steel Clevis assembly supplied complete with stainless pin. See also yokes.
|
Joints - Clevis - Steel (Relevance 7/10)
Made from zinc plated 9SMn steel.
Steel 9 SMn 28K (550-700 N/mm2). Zinc plate and clear passivated. Pin not included. See also yokes.
|
Joints - Dual Eye - Parallel (Relevance 7/10)
Maintenance free - self lubricating thermoplastic. Mechanical joining linkage. Self aligning to compensate for angular misalignment. MSTS = Maximum Static Tensile Strength. MSAS = Maximum Static Axial Compressive Strength.
|
Spacers | |
Joints - Tee - Tubing and Rod (Relevance 7/10)
Inexpensive nylon joiners for hobby tubing and rod
|
Couplings | |
Couplings - Ball (Relevance 1/10)
High Speed - Up to 15 Degrees Angular Offset. 0.17 to 22.6 N.m Torque. Up to 20,000 rpm.
Speed Ratings :. 20000 RPM at up to 5 Degree Operating Angle. 10000 RPM at 6 to 10 Degree Operating Angle (Torque Reduction 50%). 5000 RPM at 11 to 15 Degree Operating Angle (Torque Reduction 66%). Nylon centred units provide electrical insulation between shafts.
|
Couplings - Bantam - Complete (Relevance 1/10)
Isolates vibration up to 85%. Sleeve provides electrical insulation. 0.21Nm at 1725rpm.
Parallel Offset 0.25 mm. Angular Offset 1.5 Degree.
|
Couplings - Bellows - External Clamp - Brass (Relevance 1/10)
Zero Backlash - Tin Plate - Angular Misalignment up to 10 Degree (Refer Tables)
Phosphor Bronze Bellows Beryllium Copper Hubs Match with precision or commercial gear clamps - see link
|
Couplings - Bellows - External Clamp and Set Screw - Brass (Relevance 1/10)
Zero Backlash - Tin Plate - Angular Misalignment up to 5 Degree
Phosphor Bronze Bellows Brass set screw hub one end, berrylium copper clamp hub other end Match with precision or commercial gear clamps - see link
|
Couplings - Bellows - Hiflex - Clamp Hub (Relevance 1/10)
Precise adjustment - Vibration resistance - Large misalignment capability. 0.01 to 9.17 Nm. 2000 rpm. - Zero Backlash
Wide torque range. Zero cyclic speed variation during 360 Deg. Rotation. Very low torsional deflection.
|
Couplings - Bellows - Hiflex - Integral Clamp Hub (Relevance 1/10)
Precise adjustment - Vibration resistance - Large misalignment capability. 0.01 to 9.17 Nm. 2000 rpm. - Zero Backlash
Wide torque range. Zero cyclic speed variation during 360 Deg. Rotation. Very low torsional deflection.
|
Couplings - Bellows - Hiflex - Pin Hub (Relevance 1/10)
Precise adjustment - Vibration resistance - Large misalignment capability. 0.01 to 9.17 Nm. 2000 rpm. - Zero Backlash
Wide torque range. Zero cyclic speed variation during 360 Deg. Rotation. Very low torsional deflection.
|
Couplings - Bellows - Integral Clamp - 316 Stainless (Relevance 1/10)
Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics
Stainless Steel 303L Bellows Stainless Steel 316 Hubs
|
Couplings - Bellows - Integral Clamp - Aluminium (Relevance 1/10)
Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics
Phosphor Bronze Bellows Aluminium Hubs
|
Couplings - Bellows - Integral Clamp - Brass (Relevance 1/10)
Zero Backlash - Constant Angular Velocity - Dampens vibration and noise - Tin plate finish
Phosphor Bronze Bellows Brass Hubs
|
Couplings - Bellows - Modular (Relevance 1/10)
Interchangeable bushings for a variety of bore sizes.
1 Coupling consists of: 2 Bushings - 2 Clamps - 1 Bellows. Choose all 5 parts from any one size group. Bushings may be interchanged within any size group.
|
Couplings - Bellows - Set Screw - 316 Stainless (Relevance 1/10)
Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics
Stainless Steel 303L Bellows Stainless Steel 316 Hubs
|
Couplings - Bellows - Set Screw - Aluminium (Relevance 1/10)
Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics
Phosphor Bronze Bellows Aluminium Hubs
|
Couplings - Bellows - Set Screw - Brass (Relevance 1/10)
Phosphor Bronze Bellows Brass Hubs
|
Couplings - Bellows - Set Screw - Brass with Tin Plate Finish (Relevance 1/10)
Phosphor Bronze Bellows Brass with Tin Plate Finish Hubs
|
Couplings - BoWex - Junior (Relevance 1/10)
Nylon 2 piece and 3 piece couplings. 5 to 24 Nm. 6000 rpm max.
Approved distribution through the Australian Wholesaler (Deanquip). Crowned gear teeth - No need for lubrication. Chemical resistant nylon. Electrically insulated. Grub Screw opposite Keyway.
|
Couplings - Clutch - Flange Mounted (Relevance 1/10)
0.565 to 14 N.m. For in-line loads.
24 Volt DC. Zero Backlash Armature. For in-line loads. Dynamic torque is 80% of static torque. 0.565 N.m Models have no set screws in rotor - pin hole only.
|
Couplings - Clutch - Shaft Mounted (Relevance 1/10)
0.565 to 14 N.m. For in-line loads.
24 Volt DC. Zero Backlash Armature. For in-line loads. Dynamic torque is 80% of static torque. 0.565 N.m Models have no keyway in rotor.
|
Couplings - Control Flex (Relevance 1/10)
0.45 to 6.44 Nm.
MATERIALS: Hubs - Aluminium, Pins - Hardened Alloy Steel, Socket Head Screws - Alloy Steel, Control-Flex Member - Delrin® 100. Lightweight, low inertia, and no maintenance or lubrication necessary. No change in angular velocity or torque due to misalignment. No end thrust due to torque transmission. Rated torques are with all alignment factors zero. The summation of the three alignment factors should not exceed 50%. The rated torque must be reduced by the summation of the alignment factors. Operating Temperature: -23 deg to +65 deg Celsius.
|
Couplings - Crowned Tooth Gear (Relevance 1/10)
Steel hubs with Moulded Nylon Sleeve.
+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1 Degree Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.
|
Couplings - Double Disk (Relevance 1/10)
Zero Backlash - High Torsional Stiffness.
Hub and Spacer: Aluminium Alloy. Pin and Disc: Stainless Steel. Max Axial Play: +/-0.5mm. 0.7 to 12.5 Nm. 3000 to 19000 rpm.
|
Couplings - Double Disk - High Torque (Relevance 1/10)
Zero Backlash - Clamp Locking - Medium torsional stiffness.
High torsional stiffness and high response. Zero backlash. Hub: Aluminium (A2017) Spacer: Aluminium (A2011). Pin: Stainless Steel (SUS301) Disk: Stainless Steel (SUS303). Maximum Temperature: +100°C. 2.8 to 22 Nm. 2400 to 4800 rpm. Identical clockwise & anti-clockwise rotational characteristics.
|
Couplings - Flexible-Shaft Type (Relevance 1/10)
Nonmagnetic flexible shaft couplings. Max torque 0.39 Nm.
Maximum Torque 0.39 N.m (3.5 lb.in). Minium operating radius 89 mm (3.5 in.). Torsional deflection 1.8 Deg per lb.in per inch (25mm) of shaft in Winding Direction. Torsional deflection 2.6 Deg per lb.in per inch (25mm) of shaft in Unwinding Direction. Cadmium Plated Brass Ends - Phosphor Bronze Cable - 300 Series Stainless Screws.
|
Couplings - Geargrip (Relevance 1/10)
0.67 to 6.78 Nm. Max speed 3000 rpm.
Sleeve - Neoprene with Ground OD; Hub - Zinc Alloy Die Casting. Suitable operating temperature is -28 to 70 Deg. Celsius. Features: no lubrication, electrically isolated, dampens shock and vibration.
|
Couplings - HRC (Relevance 1/10)
|
Couplings - Helical - Long Series (Relevance 1/10)
2.9 to 31.4 Nm.
5 Degree max angular misalignment. 0.762 mm Parallel offset. +/- 0.254 mm Axial motion. Zero backlash.
|
Couplings - Helical - Low Inertia (Relevance 1/10)
0.8 to 13.2 Nm.
5 Degree max angular misalignment. 0.254 mm Parallel offset. +/- 0.203 mm Axial motion. Zero backlash.
|
Couplings - Helical - Precision (Relevance 1/10)
0.14 to 9 Nm. 25000 max RPM.
5 Degree max angular misalignment. 0.076 mm Parallel offset. Zero Axial motion. Zero backlash.
|
Couplings - Helical - Short - Ondrives (Relevance 1/10)
Material: 303 S3U Stainless.
|
Couplings - Helical - Standard (Relevance 1/10)
0.1 to 16.2 Nm.
Zero backlash. Max. Ang Misalignment 5 Degrees. Max Parallel Offset 0.25mm.
|
Couplings - Jaw Type - With Polyurethane Spider (Relevance 1/10)
Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm.
Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application.
|
Couplings - Jaw Type - With Rubber Spider (Relevance 1/10)
Max 3600 RPM. 0.39 to 16.27 Nm.
Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM.
|
Couplings - K Type (Relevance 1/10)
Up to 3600 RPM - Minus 20 to Plus 60 Degrees C. 0.34 to 18 Nm.
Strong, flexible polyurethane or Hyrtel® is cut and tear resistant. Up to 3600 RPM. Urethane: Minus 20 to Plus 60 Degrees C / Hyrtel® : Minus 40 to Plus 100 Degrees C. Precision swaged mechanically crimped hubs. Annealed steel hubs.
|
Couplings - Multijaw - Precision (Relevance 1/10)
Max Torque 3.5 Nm.
303 Stainless Steel. Stainless socket set screws supplied. 48 teeth - 64 Pitch. Max Torque 3.5 N.m (500 oz.in).
|
Couplings - Neo-Flex (Relevance 1/10)
0.71 to 1.27 Nm.
303 stainless steel with 73 durometer neoprene centre. Shaft to shaft insulation. Torsional vibration isolation. Ribbed style are more flexible than smooth style. Bore Tolerances: +0.025 / -0.000.
|
Couplings - Oldham - Complete (Relevance 1/10)
0.06 to 44 Nm. Max Speed: 3000 RPM.
Max Speed: 3000 RPM. Parallel out of line compensation. Temp Range -20 Deg C to +60 Deg C. Disk Material: Acetal.
|
Couplings - Oldham - Components (Relevance 1/10)
0.06 to 44 Nm. Max Speed: 3000 RPM.
Disk inserts Single hubs
|
Couplings - Rigid (Relevance 1/10)
0.35 to 5.1 Nm.
Quality Class Precision: Bore Tolerance +0.013 / - 0.000 concentric within 0.0127mm T.I.R. Quality Class Commercial: Bore Tolerance +0.051 / -0.000.
|
Couplings - Single Disk (Relevance 1/10)
0.7 to 19 Nm. 2400 to 10000 rpm.
High response. High torque. Zero backlash. High torsional stiffness.
|
Couplings - Sleeve Type (Relevance 1/10)
0.05 to 2.1 Nm. Max Speed 1750 rpm.
Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.
|
Couplings - Slip - Spring Wrapped (Relevance 1/10)
Tension control - transmission overload protection. 0.035 to 1.69 Nm.
Coupling is sliped over one shaft and screws tightened. Second shaft is inserted into other end. Loose end of coupling is pulled back about 0.5mm then screws tightened. Serves as a torque limiter as well as a coupling. Long life under continuous slip applications.
|
Couplings - Slit Type (Relevance 1/10)
Aluminium - Stainless Steel - Flexible - Zero Backlash. 0.1 to 35 Nm. 2400 to 48000 rpm.
High Torsional Stiffness. Zero Backlash.
|
Couplings - Spider Type (Relevance 1/10)
2.1 to 17 Nm.
Split Type Hub. Preloaded Rubber Spider. Minimal backlash. Choice of 3 different spiders for each size provides for different torque requirements. Hubs and spiders available separately or as a complete unit.
|
Couplings - Spiral Beam - 6 Beam (Relevance 1/10)
Pilot Bore size not toleranced. Finished Bore sizes to +0.03/0.00.
|
Couplings - Spline Type (Relevance 1/10)
0.5 to 4.5 Nm. 12000 to 24000 rpm.
Angular Misalignment: 2 Deg. Parallel Offset: 0.2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 deg C.
|
Couplings - Torque Tube (Relevance 1/10)
Internal compression spring preloads the ends against axial movement and backlash. Up to 2.8 Nm. Up to 2000 rpm.
Maximum Torque: 2.8 N.m (25 lb.in). Delrin Torque Tube. Aluminium Split Hubs. Do not compress the unit axially during installation. Speeds to 2000 rpm. One piece assembly.
|
Couplings - Uni-lat (Relevance 1/10)
0.3 to 3.5 Nm. 3000 to 6000 rpm.
Hubs (UNL18 & 27): Brass CZ 121 Chromate & passivate finish. Hubs (UNL34 and 41):Alum. Alloy 2011 T8 Alocrom finish. Bearing Rings: Black Acetal. Operating Temp. Range: -20°C to +60°C. 10° angular and 1mm radial compensation. Flex-free mechanical action - low bearing loads.
|
Couplings - Uniflex (Relevance 1/10)
High speed to 30000 rpm. 2.3 to 9.27 Nm.
Spring : 1095 Steel Hubs : Cold Rolled Steel. Operating Temperature : 121 Deg C (250 Deg F). Maximum Speed : 30000 RPM. For CUF15 series the spring diameter is the same as the hub diameter.
|
Extenders - Shaft (Relevance 1/10)
Miniature and large shaft extenders.
|
Fasteners | |
Yoke Ends - Blank (Relevance 1/10)
Linkage Connectors with blank ends - no hole
Drop forged steel machined to SAE standards Also see clevis joints
|
Yoke Ends - Threaded (Relevance 1/10)
Linkage Connectors
Drop forged steel machined to SAE standards Also see clevis joints
|
Rod Ends | |
Rod Ends - Studded - Male-Female - Quick Disconnect (Relevance 1/10)
Joints are strength, quick disconnect assemblies with good wear characteristics. Retaining sleeve insures the assembly can only be put together with the sleeve positively aligned with the ball cavity. When spring is released, alignment is automatic thereby eliminating any possiblity of partial closure. Ball stud and Body are made of low carbon steel. Studs are surface hardened. All Parts are plated and dichromate treated.
|
Shaft and Shafting | |
Shafts - Flexible - Coupling Ends - Cased (Relevance 1/10)
See PDF file at bottom of internet page for Performance Data.
|
Shafts - Flexible - Coupling Ends - Open (Ondrives) (Relevance 1/10)
Hubs: 220 MO7 / Shaft: Steel.
|
Shafts - Flexible - Coupling Ends - Open (SDP) (Relevance 1/10)
Flexible shafting with coupling ends ready to attach to a fixed shaft.
See PDF file at bottom of internet page for Performance Data.
|
|
