Categories that include the terms: STAINLESS and SHAFT
|
Fasteners |  |
Threaded Rod - Allthread - Stainless Steel (Relevance 10/10)
UNC - UNF - METRIC - 303, 304 and 316 grades.
|
Materials | |
Hexagonal Bar - 303 Stainless (Relevance 10/10)
Corrosion resistant 303 grade stainless.
Saw Cut Ends. Small A/F sizes may not be perfectly straight.
|
Rod - Round - Stainless Steel (Relevance 10/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground.
|
Square Bar - 303 Stainless (Relevance 10/10)
Corrosion resistant 303 grade stainless.
Saw Cut Ends. Smaller sizes may not be supplied straight.
|
Rod Ends | |
Rod Ends - Stainless Steel - Nylon Raceway (Relevance 10/10)
|
Bearings - Specialty | |
Bearings - Ball - 316 Stainless Steel (Relevance 8/10)
Food and Medical grade Stainless Steel - Non Hardenable.
Tolerances differ from standard bearing types - see below. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. ID +0.0762 mm / -0.000 mm OD +0.000 mm / -0.0762 mm Width +/- 0.127 mm. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races.
|
Clamping and Locking | |
Collars - Shaft - Standard (Relevance 8/10)
Includes miniature precision types. Carbon steel, 303 and 316 stainless.
|
Rod Ends | |
Rod Ends - Steel - Bronze Lined (Relevance 8/10)
Imperial and Metric / Carbon steel and Stainless Steel.
Dimensions not shown are available on request. CFF.SS series are made to DIN 648K and ISO 6126JK.
|
Rod Ends - Steel - PTFE Lined (Relevance 8/10)
Imperial and Metric. Tight fit (Minimal ball clearance) / Carbon steel and Stainless Steel.
Dimensions not shown are available on request.
|
Shaft and Shafting | |
Shafting - Ground - Precision (Relevance 8/10)
Precision ground shafting. Various materials including silver steel, 303 304 316 416 stainless steel, hardened carbon steel, chrome vanadium alloy.
|
Spacers | |
Spacers - Round - Through Bore - Stainless Steel (Relevance 8/10)
Shaft spacers - Stainless Steel
|
Washers | |
Washers - Lock - Internal Tooth - Stainless Steel (Relevance 8/10)
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
|
Balls | |
Balls - Stainless Steel - 304 Grade (Relevance 7/10)
A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.
Tolerances available on request. Grade 100. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000 Deg C.
|
Balls - Stainless Steel - 316 Grade (Relevance 7/10)
A4 Grade. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.
Tolerances available on request. Grade 100. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000 Deg C.
|
Balls - Stainless Steel - 316L Grade (Relevance 7/10)
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.
|
Balls - Stainless Steel - 440C Grade (Relevance 7/10)
Hardness: Rockwell C: 55-60.
Tolerances available on request. AISI440C Stainless Steel. Hardness: Rockwell C: 55-60.
|
Ballscrew | |
KSS Ballscrew - Rolled - Stainless - Dia 10mm - Lead 2.0mm (Relevance 7/10)
Not for sale outside of Australia and New Zealand
|
KSS Ballscrew - Rolled - Stainless - Dia 6mm - Lead 1.0mm (Relevance 7/10)
Not for sale outside of Australia and New Zealand
|
KSS Ballscrew - Rolled - Stainless - Dia 8mm - Lead 1.0mm (Relevance 7/10)
Not for sale outside of Australia and New Zealand
|
KSS Ballscrew - Rolled - Stainless - Dia 8mm - Lead 2.0mm (Relevance 7/10)
Not for sale outside of Australia and New Zealand
|
KSS Ballscrew - Rolled - Stainless - Intergrated End-Journal - Dia 10mm - Lead 2.0mm (Relevance 7/10)
Not for sale outside of Australia and New Zealand
|
KSS Ballscrew - Rolled - Stainless - Intergrated End-Journal - Dia 6mm - Lead 1.0mm (Relevance 7/10)
Not for sale outside of Australia and New Zealand
|
KSS Ballscrew - Rolled - Stainless - Intergrated End-Journal - Dia 8mm - Lead 1.0mm (Relevance 7/10)
Not for sale outside of Australia and New Zealand
|
KSS Ballscrew - Rolled - Stainless - Intergrated End-Journal - Dia 8mm - Lead 2.0mm (Relevance 7/10)
Not for sale outside of Australia and New Zealand
|
Bearings | |
Bearings - Ball - 440C Stainless 6000 / 6200 / 6300 Series (Relevance 7/10)
Stainless Steel 440C Grade - Hardened - Precision - Corrosion Resistant.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire.
|
Bearings - Specialty | |
Bearings - Acetal - with 302 Stainless Steel Balls (Relevance 7/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 302 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Bearings - Acetal - with 316 Stainless Steel Balls (Relevance 7/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Bearings - Ball - 304 Stainless Steel (Relevance 7/10)
Corrosion and Heat resistance - Non Magnetic - Unhardened.
Tolerances differ from standard bearing types - see below. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. ID +0.050 mm / -0.000 mm OD +0.000 mm / -0.030 mm Width +0.000 mm /- 0.120 mm. Low load, low speed applications requiring maximum corrosion resistance. Non Magnetic. Cages, balls, races and shields from AISI 304 Stainless Steel.
|
Cam Followers | |
Cam Followers - Roller Type - Stainless Steel (Relevance 7/10)
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
|
Clamping and Locking | |
Clamps - Shaft (Relevance 7/10)
Mild Steel: 045M10. Stainless Steel: 303S21.
|
Collars - Shaft - Clamp Type (Relevance 7/10)
|
Collars - Shaft - Fairloc (Relevance 7/10)
|
Collars - Shaft - Fastlock (Relevance 7/10)
No tools required.
Usable for Nonhardened Shafts. Inner body and Outer sleeve: 303 Stainless, Balls: 440C Stainless, Spring: 302 Stainless.
|
Collars - Shaft - Gripfast (Relevance 7/10)
Self Locking - Quick Release.
265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs.
|
Collars - Shaft - Hinged Type - Hex (Relevance 7/10)
|
Collars - Shaft - Hinged Type - Round (Relevance 7/10)
Precision machined. Convenient easy-to-assemble design.
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
|
Collars - Shaft - Stroke Adjustment (Relevance 7/10)
Recommended tolerances for mating shaft diameter : h6. Use with rubber washers listed under WASHERS.
|
Collars - Shaft - With Integral Shim (Relevance 7/10)
Bore tolerance (+0.003/+0.013). Imperial Collars have undersized tolerances. Metric Collars have oversized tolerances.
|
Shaft Locks - Potentiometer (Relevance 7/10)
|
Clutches and Brakes | |
Clutches - Shaft Mounted (Relevance 7/10)
24 V DC - Zero Backlash Armature - For parallel loads.
This basic information is designed to assist you to make a decision on which clutch to use. Full dimensions available on request.
|
Clutches - Slip - Magnetic Particle - Integral Shaft - No Power (Relevance 7/10)
Requires no power.
Sealed from contamination. Uses permanent magnets and magnetic particles. Constant torque levels. Zero maintenance - Long operational life. See PDF sheet at bottom of this page.
|
Couplings | |
Couplings - Bellows - Integral Clamp - 316 Stainless (Relevance 7/10)
Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics
Stainless Steel 303L Bellows Stainless Steel 316 Hubs
|
Couplings - Bellows - Set Screw - 316 Stainless (Relevance 7/10)
Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics
Stainless Steel 303L Bellows Stainless Steel 316 Hubs
|
Couplings - Clutch - Shaft Mounted (Relevance 7/10)
0.565 to 14 N.m. For in-line loads.
24 Volt DC. Zero Backlash Armature. For in-line loads. Dynamic torque is 80% of static torque. 0.565 N.m Models have no keyway in rotor.
|
Extenders - Shaft (Relevance 7/10)
Miniature and large shaft extenders.
|
Fasteners | |
Joints - Clevis - Stainless Steel (Relevance 7/10)
Stainless 1.4305 Stainless Steel Clevis assembly supplied complete with stainless pin. See also yokes.
|
Nuts - Cap - Stainless Steel (Relevance 7/10)
Stainless Steel. Lower profile than a dome nut.
|
Nuts - Dome - Stainless Steel (Relevance 7/10)
Stainless Steel.
|
Nuts - Hexagonal - Half - Stainless Steel (Relevance 7/10)
UNC - UNF - METRIC
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Stainless Steel (Relevance 7/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Stainless Steel (Relevance 7/10)
UNC - UNF - BA - METRIC - BSW - Course - Fine - Extra Fine.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Wing - Stainless Steel (Relevance 7/10)
304 and 316 Stainless Wing Nuts
|
Pins - Clevis - Stainless Steel 304 (Relevance 7/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Clevis - Stainless Steel 316 (Relevance 7/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Cotter - Stainless Steel (Relevance 7/10)
Split pins.
|
Pins - Dowel - Standard - Stainless Steel (Relevance 7/10)
Precision Dowel Pins - Various Corrosion Resistant Grades.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Pins - Roll - Stainless Steel (Relevance 7/10)
304 and 420 grades DIN1481.
|
Screws - Coach - Stainless Steel (Relevance 7/10)
|
Screws - Machine - Stainless Steel (Relevance 7/10)
Metal Thread Screws UNC - UNF - METRIC - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Stainless Steel - Countersunk Head (Relevance 7/10)
Flat Head Countersunk UNC - UNF - METRIC.
Nuts sold seperately - See Nuts.
|
Screws - Security - Socket - Countersunk - Stainless Steel (Relevance 7/10)
Use special tool listed under Screws - Securty - Socket - Tools.
|
Screws - Socket - Button - Stainless Steel (Relevance 7/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Cap - Stainless (Relevance 7/10)
UNC - UNF - METRIC - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Countersunk - Stainless Steel (Relevance 7/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Threaded Rod - Allthread - Brass (Relevance 7/10)
UNC - UNF - METRIC brass.
|
Threaded Rod - Allthread - Plastic (Relevance 7/10)
UNC - UNF - METRIC - Nylon and PVC.
Light Weight. Non Corrosive. Vibration Resistant.
|
Threaded Rod - Allthread - Steel (Relevance 7/10)
UNC - UNF - METRIC - BSW - Includes plain and zinc plated, mild steel and high tensile.
|
Threaded Rod - Aluminium (Relevance 7/10)
UNC and UNF light weight aluminium.
|
Frame Kits | |
Automat - Frame Kit Threaded Rods (Relevance 7/10)
All M3.5 Thread. See PDF file in FTP Directory for more information. Educational tool suitable for mechanical teaching institutions.
All M3.5 Thread Mild Steel.
|
Gearboxes | |
Gearboxes - Output Shafts (Relevance 7/10)
For use in Cross Axis gearboxes with bores. P and PF Series.
Stainless 303 shaft. Steel keys and circlips. P-X and P-DX types suitable for P and PF type gearboxes (cross axis types).
|
Handles and Knobs | |
Knobs - Ball - Threaded - Stainless Steel (Relevance 7/10)
303 stainless steel (European grade 1.4305)
|
Knobs - Lobe - Stainless Steel (Relevance 7/10)
AISI 303 Stainless Steel. Suitable for food, chemical and pharmaceutical equipment.
|
Knobs - Star - Female - 304 Stainless (Relevance 7/10)
AISI 304 sand-blasted stainless steel, with matte finish. Butt-welded with H7 tolerance plain blind hole (Type C) or tapped blind hole (Type E). The low sulphur contents of AISI 304 stainless steel (less than 0.03%) makes them particularly resistant to corrosion.
|
Housings with Integral Bearing | |
Housings - Bearing - Blocks - Nylon with Stainless Bearing (Relevance 7/10)
Moulded Nylon 101 Housing with 440C Stainless Bearing.
Bearing block: Nylon / Bearing: 440C Stainless / Insert: 52100 Chrome Steel. High Performance. Housing is Electrically Insulating. Not intended for precision applications. Inner assembly not fixed in place. Can be used as a floating assembly or fixed using conventional adhesives or circlips.
|
Linear Ball Splines | |
Linear Ball Splines - Shaft (Relevance 7/10)
Use with either flanged or unflanged Linear Ball Spline Bearings.
|
Linear Drive Systems - Leadscrew | |
Leadscrews - Metric - Rolled Thread - Stainless Steel (Relevance 7/10)
Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.
Stainless steel 316L. For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.
|
Leadscrews - Metric - Whirled Thread - Stainless Steel (Relevance 7/10)
Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.
Longer lengths may be available on request. Single Start. 303 Stainless Steel Whirled screw left hand and right hand cut on same single piece of material to DIN103 Grade 7e. Use with Trapezoidal Nuts.
|
Linear Shaft | |
Shafting - Linear - Square (Relevance 7/10)
|
Magnets | |
Magnets - Alcomax - Cylindrical Bar (Relevance 7/10)
No keepers
|
Magnets - Alcomax - Rectangular Bar (Relevance 7/10)
No keepers
|
Magnets - Alnico - Bar (Relevance 7/10)
Cast Alnico 5 bar
|
Magnets - Alnico - Rod - Sintered (Relevance 7/10)
|
Materials | |
Bar - H Section - Brass (Relevance 7/10)
|
Bar - I Beam - Brass (Relevance 7/10)
|
Hexagonal Bar - Brass (Relevance 7/10)
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Small A/F sizes may not be perfectly straight.
|
Hexagonal Bar - Carbon Steel (Relevance 7/10)
Saw Cut Ends. Small A/F sizes may not be perfectly straight.
|
Rectangular Bar - Aluminum (Relevance 7/10)
Thin and thick Aluminum strip and rectangular profiles
Small sizes may not be perfectly straight.
|
Rectangular Bar - Brass (Relevance 7/10)
Thin and thick brass strip and rectangular profiles
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Small sizes may not be perfectly straight.
|
Rod - Drill Blanks (Relevance 7/10)
Made of hardened high speed steel.
Useful for turning and boring tools, constructing pins, hinge pins, arbors, pin gauges, dowels, preforating punchs. Can also be ground to make special cutting tools such as mills, spotfaces, angle or radii cutters, etc.
|
Rod - Round - Acetal (Relevance 7/10)
Hard, stiff plastic for machining bushes, gears etc with close tolerances. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.41 g/cm3 - Operating Temp -40 to 120 C. Tensile Strength 60-70 Mpa / Hardness 80 Rockwell M. Small diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Aluminium (Relevance 7/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Rod - Round - Brass (Relevance 7/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Rod - Round - Bronze - LG2 (Standard) (Relevance 7/10)
Leaded Gunmetal Bronze. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Longer lengths available on special request. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. AS1565-83600 / Hardness : 70-90 BHN. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Rod - Round - Carbon Fibre (Relevance 7/10)
High impact light weight carbon fibre for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish Items marked as Low Grade may have tolerance variations up to 0.2mm
|
Rod - Round - Glass Fibre (Relevance 7/10)
High impact light weight glass fibre for modelling.
Glass fibre rod is not smooth.
|
Rod - Round - Nylon (Relevance 7/10)
High impact strength and toughness. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.13 g/cm3 - Operating Temp -40 to 160 C. Tensile Strength 78 Mpa / Hardness 82 Rockwell M. Co-efficient of friction 0.20-0.30. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - PTFE (Relevance 7/10)
Lowest co-efficient of friction. Excellent chemical resistance. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 2.20 g/cm3 - Operating Temp -260 to 260 C. Tensile Strength 10-40 Mpa / Hardness D50-55 Shore. Co-efficient of friction 0.05-0.20. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Polyester PETP (Relevance 7/10)
High mechanical strength, stiffness and hardness. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.39 g/cm3 - Operating Temp 115 C / 5000 hrs - 100 C / 20000 hrs. Tensile Strength 90 Mpa. Hardness 96 Rockwell M. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Sintered Bronze (Relevance 7/10)
Sintered bronze is supplied oversized so it can be machine finished to the dimensions shown.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Oil impregnated porous bronze rod. Smaller diameters may not be supplied straight.
|
Rod - Round - Urethane (Relevance 7/10)
Hard urethane rubber compound. Machinable. Length +/- 3.2mm. Diameter +/- 2 percent
|
Square Bar - Brass (Relevance 7/10)
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Smaller sizes may not be supplied straight.
|
Square Bar - Carbon Steel (Relevance 7/10)
Saw Cut Ends. Smaller sizes may not be supplied straight.
|
Square Bar - Urethane (Relevance 7/10)
Hard urethane rubber compound. Machinable. Length +/- 3.2mm. Length +/- 2 percent
|
Tube - Round - Stainless Steel (Relevance 7/10)
Hollow round tubing for general hobby applications.
For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Wire - Steel - 302 Stainless (Relevance 7/10)
302 Stainless Steel
|
Plain Bearings | |
Bushings - Spherical - Stainless Steel (Relevance 7/10)
Stainless Steel
Compensates for axial loads and misalignment.
|
Pneumatic | |
Airmovers - Adjustable - Stainless Steel (Relevance 7/10)
Airmovers amplify air flow from a small supply of compressed air. Terrific for fume or smoke extraction or to move large volumes of light weight materials.
|
Retaining Rings and Clips | |
Snaprings - External - Stainless Steel (Relevance 7/10)
301 S11/S22 Stainless Steel.
|
Snaprings - Internal - Stainless Steel (Relevance 7/10)
301 S11/S22 Stainless Steel.
|
Rod Ends | |
Rod Ends - Heavy Duty - Ball (Relevance 7/10)
With integral self aligning ball bearing.
With grease nipple. Housing: Tempered forged steel. Bearing Race: Case hardened. Thread: Rolled - Surface galvanised. Inner Ring: Ball bearing steel. Hardened, ground. Lubrication: Calcium Complex Soap Grease temperature range -20ºC to +120ºC.
|
Rod Ends - Heavy Duty - Ball - Enlarged Eye (Relevance 7/10)
With integral self aligning ball bearing.
With grease nipple. Housing: Tempered forged steel. Bearing Race: Case hardened. Thread: Rolled - Surface galvanised. Inner Ring: Ball bearing steel. Hardened, ground. Lubrication: Calcium Complex Soap Grease temperature range -20ºC to +120ºC.
|
Rod Ends - Heavy Duty - Ball - Reduced Eye (Relevance 7/10)
With integral self aligning ball bearing.
With grease nipple. Housing: Tempered forged steel. Bearing Race: Case hardened. Thread: Rolled - Surface galvanised. Inner Ring: Ball bearing steel. Hardened, ground. Lubrication: Calcium Complex Soap Grease temperature range -20ºC to +120ºC.
|
Rod Ends - Heavy Duty - Roller (Relevance 7/10)
With integral self aligning roller bearing.
With grease nipple. Housing: Tempered forged steel. Bearing Race: Case hardened. Thread: Rolled - Surface galvanised. Inner Ring: Ball bearing steel. Hardened, ground. Lubrication: Calcium Complex Soap Grease temperature range -20ºC to +120ºC.
|
Rod Ends - Plastic (Relevance 7/10)
Thermoplastic Body / L280® Polymer Ball.
Dimensions not shown are available on request.
|
Rod Ends - Stamped (Relevance 7/10)
Economy stamped style combines high strength with low cost
Made from low carbon steel and plated for corrosion resistance. Ball is case hardened.
|
Rod Ends - Steel - Nylon Raceway (Relevance 7/10)
|
Rod Ends - Steel - PTFE Liner (Relevance 7/10)
|
Rod Ends - Studded - Male-Female - Nylon (Relevance 7/10)
Housing is plated and dichromate treated steel. Ball is case hardened and plated Stud is permanently affixed and made from heat treated alloy steel, zinc plated.
|
Rod Ends - Studded - Male-Female - PTFE (Relevance 7/10)
Housing is plated and dichromate treated steel. Ball is case hardened and plated Stud is permanently affixed and made from heat treated alloy steel, zinc plated.
|
Rod Ends - Studded - Male-Female - Quick Disconnect (Relevance 7/10)
Joints are strength, quick disconnect assemblies with good wear characteristics. Retaining sleeve insures the assembly can only be put together with the sleeve positively aligned with the ball cavity. When spring is released, alignment is automatic thereby eliminating any possiblity of partial closure. Ball stud and Body are made of low carbon steel. Studs are surface hardened. All Parts are plated and dichromate treated.
|
Rod Ends - Studded - Male-Female - Swaged Construction (Relevance 7/10)
Designed for heavy duty service, they come with dirt shield to provide protection against contaminants.
Unique assembly swages metal to retain the ball in cavity resulting in increased pull out and wear resistance. Ball studs are surface hardened. Made of low carbon steel, plated and dichromate treated.
|
Rod Ends - Studded - Male-Male - Nylon (Relevance 7/10)
Housing is plated and dichromate treated steel. Ball is case hardened and plated Stud is permanently affixed and made from heat treated alloy steel, zinc plated.
|
Rod Ends - Studded - Male-Male - PTFE (Relevance 7/10)
Housing is plated and dichromate treated steel. Ball is case hardened and plated Stud is permanently affixed and made from heat treated alloy steel, zinc plated.
|
Roller Chain and Sprockets | |
Chain - Roller - Metal - Simplex - Links - Stainless Steel (Relevance 7/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Stainless Steel (Relevance 7/10)
Includes Miniature Sizes.
|
Sprockets - 3.75mm Pitch - Simplex - Stainless Steel (Relevance 7/10)
With and without Hubs. Miniature 3.75mm Pitch.
Match with 0375 Series Simplex Chain
|
Sprockets - 6.35mm Pitch - Simplex - Stainless Steel (Relevance 7/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Rollers | |
Rollers - Idler - Stainless Steel (Relevance 7/10)
|
Seals and Sealing | |
Sealing Plugs - Stainless (Relevance 7/10)
The sealing plug is a safe, quick, leakproof and low cost method for sealing cross-drilled holes. It ensures peak performance with a comfortable safety margin even in extreme applications.
Sleeve: Stainless Steel DIN 1.4305, AISI 303 Ball: Bearing Steel, Heat Treated Hardness: HB = 220
|
Shaft and Shafting | |
Rail Supports - With Shaft (Relevance 7/10)
Includes shaft.
Includes shaft to h6 tolerances.
|
Rail Supports - Without Shaft (Relevance 7/10)
For mounting of shafting.
Shafting sold separately.
|
Rod - Drill (Relevance 7/10)
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
Unfinished ends. Requires heat treating to harden. Small diameters may not be perfectly straight.
|
Shafting - Aluminium (Relevance 7/10)
Drylin aluminium shafting is recommended for use with Igubal Drylin bearings only.
Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: >40µm. Surface Hardness: 450-550 HV. Roughness: Ra<0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: ph between 2 and 9.
|
Shafting - Keyed (Relevance 7/10)
Keyways are cut full length of each bar.
Diameter Tolerance +0.05/-0.00 Keyway Depth Tolerance +0.41/-0.00 Keyway Width Tolerance +0.05/-0.00
|
Shafting - Pipe - AISI52100 Steel (Relevance 7/10)
AISI 52100 Steel Hardened to HRC 58-62. Straightness 0.0003 mm / mm. Ideal for design weight reduction. Note! ID of pipe shaft may be up to 1mm undersize. Other lengths may be available on request however a surcharge for special sizing will apply and extended delivery times can be expected (if available).
|
Shafting - Pipe - Aluminium (Relevance 7/10)
Recommended for use with Igubal Drylin bearings only.
Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: >40µm. Surface Hardness: 450-550 HV. Roughness: Ra<0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: 2
|
Shafting - Pre Drilled for Rail Supports (Relevance 7/10)
Straightness: 0.1 mm / mtr.
|
Shafting - Supported - Pre-Drilled - Aluminium (Relevance 7/10)
For Drylin Bearings.
Material : AlMgSi 0.5 F22. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: >40µm. Surface Hardness: 450-550 HV. Roughness: Ra<0.5. Spec. Electr. Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: 2
|
Shafts - Flexible - Coupling Ends - Cased (Relevance 7/10)
See PDF file at bottom of internet page for Performance Data.
|
Shafts - Flexible - Coupling Ends - Open (Ondrives) (Relevance 7/10)
Hubs: 220 MO7 / Shaft: Steel.
|
Shafts - Flexible - Coupling Ends - Open (SDP) (Relevance 7/10)
Flexible shafting with coupling ends ready to attach to a fixed shaft.
See PDF file at bottom of internet page for Performance Data.
|
Shafts - Flexible - Panel Mount - Cased (Relevance 7/10)
See PDF file at bottom of internet page for Performance Data.
|
Shafts - Flexible - Panel Mount - Open (Relevance 7/10)
See PDF file at bottom of internet page for Performance Data.
|
Shafts - Pinion (Relevance 7/10)
|
Supports - Block (Relevance 7/10)
For linear shafting.
Material: Aluminium.
|
Supports - Flanged Four Bolt (Relevance 7/10)
For linear shafting.
Housing made of Cast Aluminium. Clamping Screw (supplied) made of Steel.
|
Supports - Flanged Two Bolt (Relevance 7/10)
For linear shafting.
Housing made of Cast Aluminium. Clamping Screw (supplied) made of Steel.
|
Supports - Pedestal Two Bolt (Relevance 7/10)
For linear shafting.
Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel.
|
Shim | |
Shim and Foil - Stainless Steel (Relevance 7/10)
Shim sheet. Very thin foil to thick sizes. Includes 416, 303 and 316 grades.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Spacers | |
Joints - Tee - Tubing and Rod (Relevance 7/10)
Inexpensive nylon joiners for hobby tubing and rod
|
Spacers - Hex - Threaded - Stainless Steel (Relevance 7/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
|
