Categories that include the term: SHAFT
|
Clamping and Locking |  |
Clamps - Shaft (Relevance 10/10)
Mild Steel: 045M10. Stainless Steel: 303S21.
|
Collars - Shaft - Clamp Type (Relevance 10/10)
|
Collars - Shaft - Fairloc (Relevance 10/10)
|
Collars - Shaft - Fastlock (Relevance 10/10)
No tools required.
Usable for Nonhardened Shafts. Inner body and Outer sleeve: 303 Stainless, Balls: 440C Stainless, Spring: 302 Stainless.
|
Collars - Shaft - Gripfast (Relevance 10/10)
Self Locking - Quick Release.
265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs.
|
Collars - Shaft - Hinged Type - Hex (Relevance 10/10)
|
Collars - Shaft - Hinged Type - Round (Relevance 10/10)
Precision machined. Convenient easy-to-assemble design.
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
|
Collars - Shaft - Standard (Relevance 10/10)
Includes miniature precision types. Carbon steel, 303 and 316 stainless.
|
Collars - Shaft - Stroke Adjustment (Relevance 10/10)
Recommended tolerances for mating shaft diameter : h6. Use with rubber washers listed under WASHERS.
|
Collars - Shaft - With Integral Shim (Relevance 10/10)
Bore tolerance (+0.003/+0.013). Imperial Collars have undersized tolerances. Metric Collars have oversized tolerances.
|
Shaft Locks - Potentiometer (Relevance 10/10)
|
Clutches and Brakes | |
Clutches - Shaft Mounted (Relevance 10/10)
24 V DC - Zero Backlash Armature - For parallel loads.
This basic information is designed to assist you to make a decision on which clutch to use. Full dimensions available on request.
|
Clutches - Slip - Magnetic Particle - Integral Shaft - No Power (Relevance 10/10)
Requires no power.
Sealed from contamination. Uses permanent magnets and magnetic particles. Constant torque levels. Zero maintenance - Long operational life. See PDF sheet at bottom of this page.
|
Couplings | |
Couplings - Clutch - Shaft Mounted (Relevance 10/10)
0.565 to 14 N.m. For in-line loads.
24 Volt DC. Zero Backlash Armature. For in-line loads. Dynamic torque is 80% of static torque. 0.565 N.m Models have no keyway in rotor.
|
Extenders - Shaft (Relevance 10/10)
Miniature and large shaft extenders.
|
Fasteners | |
Threaded Rod - Allthread - Brass (Relevance 10/10)
UNC - UNF - METRIC brass.
|
Threaded Rod - Allthread - Plastic (Relevance 10/10)
UNC - UNF - METRIC - Nylon and PVC.
Light Weight. Non Corrosive. Vibration Resistant.
|
Threaded Rod - Allthread - Stainless Steel (Relevance 10/10)
UNC - UNF - METRIC - 303, 304 and 316 grades.
|
Threaded Rod - Allthread - Steel (Relevance 10/10)
UNC - UNF - METRIC - BSW - Includes plain and zinc plated, mild steel and high tensile.
|
Threaded Rod - Aluminium (Relevance 10/10)
UNC and UNF light weight aluminium.
|
Frame Kits | |
Automat - Frame Kit Threaded Rods (Relevance 10/10)
All M3.5 Thread. See PDF file in FTP Directory for more information. Educational tool suitable for mechanical teaching institutions.
All M3.5 Thread Mild Steel.
|
Gearboxes | |
Gearboxes - Output Shafts (Relevance 10/10)
For use in Cross Axis gearboxes with bores. P and PF Series.
Stainless 303 shaft. Steel keys and circlips. P-X and P-DX types suitable for P and PF type gearboxes (cross axis types).
|
Linear Ball Splines | |
Linear Ball Splines - Shaft (Relevance 10/10)
Use with either flanged or unflanged Linear Ball Spline Bearings.
|
Linear Shaft | |
Shafting - Linear - Square (Relevance 10/10)
|
Magnets | |
Magnets - Alcomax - Cylindrical Bar (Relevance 10/10)
No keepers
|
Magnets - Alcomax - Rectangular Bar (Relevance 10/10)
No keepers
|
Magnets - Alnico - Bar (Relevance 10/10)
Cast Alnico 5 bar
|
Magnets - Alnico - Rod - Sintered (Relevance 10/10)
|
Materials | |
Bar - H Section - Brass (Relevance 10/10)
|
Bar - I Beam - Brass (Relevance 10/10)
|
Hexagonal Bar - 303 Stainless (Relevance 10/10)
Corrosion resistant 303 grade stainless.
Saw Cut Ends. Small A/F sizes may not be perfectly straight.
|
Hexagonal Bar - Brass (Relevance 10/10)
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Small A/F sizes may not be perfectly straight.
|
Hexagonal Bar - Carbon Steel (Relevance 10/10)
Saw Cut Ends. Small A/F sizes may not be perfectly straight.
|
Rectangular Bar - Aluminum (Relevance 10/10)
Thin and thick Aluminum strip and rectangular profiles
Small sizes may not be perfectly straight.
|
Rectangular Bar - Brass (Relevance 10/10)
Thin and thick brass strip and rectangular profiles
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Small sizes may not be perfectly straight.
|
Rod - Drill Blanks (Relevance 10/10)
Made of hardened high speed steel.
Useful for turning and boring tools, constructing pins, hinge pins, arbors, pin gauges, dowels, preforating punchs. Can also be ground to make special cutting tools such as mills, spotfaces, angle or radii cutters, etc.
|
Rod - Round - Acetal (Relevance 10/10)
Hard, stiff plastic for machining bushes, gears etc with close tolerances. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.41 g/cm3 - Operating Temp -40 to 120 C. Tensile Strength 60-70 Mpa / Hardness 80 Rockwell M. Small diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Aluminium (Relevance 10/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Rod - Round - Brass (Relevance 10/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Rod - Round - Bronze - LG2 (Standard) (Relevance 10/10)
Leaded Gunmetal Bronze. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Longer lengths available on special request. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. AS1565-83600 / Hardness : 70-90 BHN. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Rod - Round - Carbon Fibre (Relevance 10/10)
High impact light weight carbon fibre for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish Items marked as Low Grade may have tolerance variations up to 0.2mm
|
Rod - Round - Glass Fibre (Relevance 10/10)
High impact light weight glass fibre for modelling.
Glass fibre rod is not smooth.
|
Rod - Round - Nylon (Relevance 10/10)
High impact strength and toughness. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.13 g/cm3 - Operating Temp -40 to 160 C. Tensile Strength 78 Mpa / Hardness 82 Rockwell M. Co-efficient of friction 0.20-0.30. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - PTFE (Relevance 10/10)
Lowest co-efficient of friction. Excellent chemical resistance. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 2.20 g/cm3 - Operating Temp -260 to 260 C. Tensile Strength 10-40 Mpa / Hardness D50-55 Shore. Co-efficient of friction 0.05-0.20. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Polyester PETP (Relevance 10/10)
High mechanical strength, stiffness and hardness. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.39 g/cm3 - Operating Temp 115 C / 5000 hrs - 100 C / 20000 hrs. Tensile Strength 90 Mpa. Hardness 96 Rockwell M. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Sintered Bronze (Relevance 10/10)
Sintered bronze is supplied oversized so it can be machine finished to the dimensions shown.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Oil impregnated porous bronze rod. Smaller diameters may not be supplied straight.
|
Rod - Round - Stainless Steel (Relevance 10/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground.
|
Rod - Round - Urethane (Relevance 10/10)
Hard urethane rubber compound. Machinable. Length +/- 3.2mm. Diameter +/- 2 percent
|
Square Bar - 303 Stainless (Relevance 10/10)
Corrosion resistant 303 grade stainless.
Saw Cut Ends. Smaller sizes may not be supplied straight.
|
Square Bar - Brass (Relevance 10/10)
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Smaller sizes may not be supplied straight.
|
Square Bar - Carbon Steel (Relevance 10/10)
Saw Cut Ends. Smaller sizes may not be supplied straight.
|
Square Bar - Urethane (Relevance 10/10)
Hard urethane rubber compound. Machinable. Length +/- 3.2mm. Length +/- 2 percent
|
Rod Ends | |
Rod Ends - Heavy Duty - Ball (Relevance 10/10)
With integral self aligning ball bearing.
With grease nipple. Housing: Tempered forged steel. Bearing Race: Case hardened. Thread: Rolled - Surface galvanised. Inner Ring: Ball bearing steel. Hardened, ground. Lubrication: Calcium Complex Soap Grease temperature range -20ºC to +120ºC.
|
Rod Ends - Heavy Duty - Ball - Enlarged Eye (Relevance 10/10)
With integral self aligning ball bearing.
With grease nipple. Housing: Tempered forged steel. Bearing Race: Case hardened. Thread: Rolled - Surface galvanised. Inner Ring: Ball bearing steel. Hardened, ground. Lubrication: Calcium Complex Soap Grease temperature range -20ºC to +120ºC.
|
Rod Ends - Heavy Duty - Ball - Reduced Eye (Relevance 10/10)
With integral self aligning ball bearing.
With grease nipple. Housing: Tempered forged steel. Bearing Race: Case hardened. Thread: Rolled - Surface galvanised. Inner Ring: Ball bearing steel. Hardened, ground. Lubrication: Calcium Complex Soap Grease temperature range -20ºC to +120ºC.
|
Rod Ends - Heavy Duty - Roller (Relevance 10/10)
With integral self aligning roller bearing.
With grease nipple. Housing: Tempered forged steel. Bearing Race: Case hardened. Thread: Rolled - Surface galvanised. Inner Ring: Ball bearing steel. Hardened, ground. Lubrication: Calcium Complex Soap Grease temperature range -20ºC to +120ºC.
|
Rod Ends - Plastic (Relevance 10/10)
Thermoplastic Body / L280® Polymer Ball.
Dimensions not shown are available on request.
|
Rod Ends - Stainless Steel - Nylon Raceway (Relevance 10/10)
|
Rod Ends - Stamped (Relevance 10/10)
Economy stamped style combines high strength with low cost
Made from low carbon steel and plated for corrosion resistance. Ball is case hardened.
|
Rod Ends - Steel - Bronze Lined (Relevance 10/10)
Imperial and Metric / Carbon steel and Stainless Steel.
Dimensions not shown are available on request. CFF.SS series are made to DIN 648K and ISO 6126JK.
|
Rod Ends - Steel - Nylon Raceway (Relevance 10/10)
|
Rod Ends - Steel - PTFE Lined (Relevance 10/10)
Imperial and Metric. Tight fit (Minimal ball clearance) / Carbon steel and Stainless Steel.
Dimensions not shown are available on request.
|
Rod Ends - Steel - PTFE Liner (Relevance 10/10)
|
Rod Ends - Studded - Male-Female - Nylon (Relevance 10/10)
Housing is plated and dichromate treated steel. Ball is case hardened and plated Stud is permanently affixed and made from heat treated alloy steel, zinc plated.
|
Rod Ends - Studded - Male-Female - PTFE (Relevance 10/10)
Housing is plated and dichromate treated steel. Ball is case hardened and plated Stud is permanently affixed and made from heat treated alloy steel, zinc plated.
|
Rod Ends - Studded - Male-Female - Quick Disconnect (Relevance 10/10)
Joints are strength, quick disconnect assemblies with good wear characteristics. Retaining sleeve insures the assembly can only be put together with the sleeve positively aligned with the ball cavity. When spring is released, alignment is automatic thereby eliminating any possiblity of partial closure. Ball stud and Body are made of low carbon steel. Studs are surface hardened. All Parts are plated and dichromate treated.
|
Rod Ends - Studded - Male-Female - Swaged Construction (Relevance 10/10)
Designed for heavy duty service, they come with dirt shield to provide protection against contaminants.
Unique assembly swages metal to retain the ball in cavity resulting in increased pull out and wear resistance. Ball studs are surface hardened. Made of low carbon steel, plated and dichromate treated.
|
Rod Ends - Studded - Male-Male - Nylon (Relevance 10/10)
Housing is plated and dichromate treated steel. Ball is case hardened and plated Stud is permanently affixed and made from heat treated alloy steel, zinc plated.
|
Rod Ends - Studded - Male-Male - PTFE (Relevance 10/10)
Housing is plated and dichromate treated steel. Ball is case hardened and plated Stud is permanently affixed and made from heat treated alloy steel, zinc plated.
|
Shaft and Shafting | |
Rail Supports - With Shaft (Relevance 10/10)
Includes shaft.
Includes shaft to h6 tolerances.
|
Rail Supports - Without Shaft (Relevance 10/10)
For mounting of shafting.
Shafting sold separately.
|
Rod - Drill (Relevance 10/10)
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
Unfinished ends. Requires heat treating to harden. Small diameters may not be perfectly straight.
|
Shafting - Aluminium (Relevance 10/10)
Drylin aluminium shafting is recommended for use with Igubal Drylin bearings only.
Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: >40µm. Surface Hardness: 450-550 HV. Roughness: Ra<0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: ph between 2 and 9.
|
Shafting - Ground - Precision (Relevance 10/10)
Precision ground shafting. Various materials including silver steel, 303 304 316 416 stainless steel, hardened carbon steel, chrome vanadium alloy.
|
Shafting - Keyed (Relevance 10/10)
Keyways are cut full length of each bar.
Diameter Tolerance +0.05/-0.00 Keyway Depth Tolerance +0.41/-0.00 Keyway Width Tolerance +0.05/-0.00
|
Shafting - Pipe - AISI52100 Steel (Relevance 10/10)
AISI 52100 Steel Hardened to HRC 58-62. Straightness 0.0003 mm / mm. Ideal for design weight reduction. Note! ID of pipe shaft may be up to 1mm undersize. Other lengths may be available on request however a surcharge for special sizing will apply and extended delivery times can be expected (if available).
|
Shafting - Pipe - Aluminium (Relevance 10/10)
Recommended for use with Igubal Drylin bearings only.
Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: >40µm. Surface Hardness: 450-550 HV. Roughness: Ra<0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: 2
|
Shafting - Pre Drilled for Rail Supports (Relevance 10/10)
Straightness: 0.1 mm / mtr.
|
Shafting - Supported - Pre-Drilled - Aluminium (Relevance 10/10)
For Drylin Bearings.
Material : AlMgSi 0.5 F22. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: >40µm. Surface Hardness: 450-550 HV. Roughness: Ra<0.5. Spec. Electr. Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: 2
|
Shafts - Flexible - Coupling Ends - Cased (Relevance 10/10)
See PDF file at bottom of internet page for Performance Data.
|
Shafts - Flexible - Coupling Ends - Open (Ondrives) (Relevance 10/10)
Hubs: 220 MO7 / Shaft: Steel.
|
Shafts - Flexible - Coupling Ends - Open (SDP) (Relevance 10/10)
Flexible shafting with coupling ends ready to attach to a fixed shaft.
See PDF file at bottom of internet page for Performance Data.
|
Shafts - Flexible - Panel Mount - Cased (Relevance 10/10)
See PDF file at bottom of internet page for Performance Data.
|
Shafts - Flexible - Panel Mount - Open (Relevance 10/10)
See PDF file at bottom of internet page for Performance Data.
|
Shafts - Pinion (Relevance 10/10)
|
Supports - Block (Relevance 10/10)
For linear shafting.
Material: Aluminium.
|
Supports - Flanged Four Bolt (Relevance 10/10)
For linear shafting.
Housing made of Cast Aluminium. Clamping Screw (supplied) made of Steel.
|
Supports - Flanged Two Bolt (Relevance 10/10)
For linear shafting.
Housing made of Cast Aluminium. Clamping Screw (supplied) made of Steel.
|
Supports - Pedestal Two Bolt (Relevance 10/10)
For linear shafting.
Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel.
|
Spacers | |
Joints - Tee - Tubing and Rod (Relevance 10/10)
Inexpensive nylon joiners for hobby tubing and rod
|
Splined Shafts and Bushes | |
Splined Bushes - Flanged (Relevance 10/10)
Steel C45 (080M46) : ISO 14 (DIN 5463) Medium Series. Phosphor Bronze : ISO 14 (DIN 5463) Medium Series. Machinable. (Tolerances do not follow ISO 14 Standard). Steel on Steel is not meant for sliding applications. Steel on Bronze is OK for intermittent sliding under load.
|
Splined Bushes - Unflanged (Relevance 10/10)
Match with same size External splined shafts.
Match bushes and shafts by Major Diameter.
|
Splined Shafts (Relevance 10/10)
Match with same size internal splined bushes.
Match bushes and shafts by Major Diameter.
|
Splines - Ball - Telescoping (Relevance 10/10)
|
Clamping and Locking | |
Shaftloc-tm Simple Type M (Relevance 6/10)
Simple effective way to lock components onto shafts.
Passivated 416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened Precision, dynamically balanced and suitable for high speed applications. Diameters A and B concentric within 0.013 T.I.R. Tightening the nut causes slotted sleeve to contract, gripping the shaft and clamping the component to the sleeve.
|
Shaftloc-tm Sleeves - Double Ended (Relevance 6/10)
Simple effective way to lock components onto shafts.
416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened
|
Shaftloc-tm Sleeves - Single Ended (Relevance 6/10)
Simple effective way to lock components onto shafts.
416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened
|
Couplings | |
Couplings - Flexible-Shaft Type (Relevance 6/10)
Nonmagnetic flexible shaft couplings. Max torque 0.39 Nm.
Maximum Torque 0.39 N.m (3.5 lb.in). Minium operating radius 89 mm (3.5 in.). Torsional deflection 1.8 Deg per lb.in per inch (25mm) of shaft in Winding Direction. Torsional deflection 2.6 Deg per lb.in per inch (25mm) of shaft in Unwinding Direction. Cadmium Plated Brass Ends - Phosphor Bronze Cable - 300 Series Stainless Screws.
|
Clamping and Locking | |
Shaftloc-tm Clamp Type A (Relevance 4/10)
Simple effective component clamping
Passivated 416 Stainless Steel Simple two part screw together system clamps parts securely together. Vibration resistant. Employing a special asymetric thread to self-lock when the nut encounters resistance. The nut turns freely until it contacts the parts being clamped together. Additional turns wedge the parts into a locked and vibration resistant condition.
|
Balls | |
Balls - Bored - Plastic (Relevance 3/10)
Bored acetal balls as used in plastic rod ends.
Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight.
|
Balls - Bored - Steel (Relevance 3/10)
Bored steel balls as used in steel rod ends.
Hardness: 58-64 Rc. Material: SUJ-2.
|
Clamping and Locking | |
Assemblies - Locking - Flanged (Relevance 3/10)
Suitable for locking sprockets, pulleys, eccentric shafts.
Locks components with a bore of (D) to shafts with a diameter of (d). C60 Steel (060A62). Outer ring expands whilst inner ring contracts. Flange eliminates axial movement of secured component. During tightening of the screws, the hub must be able to perform axial movement. Clearance h8 / H8. Surface roughness Rt max 10um shaft / hub.
|
Assemblies - Locking - Unflanged (Relevance 3/10)
Suitable for locking sprockets, pulleys, eccentric shafts.
Locks components with a bore of (D) to shafts with a diameter of (d). C60 Steel (060A62). Outer ring expands whilst inner ring contracts. During tightening of the screws, the hub must be able to perform axial movement. Clearance h8 / H8. Surface roughness Rt max 10um shaft / hub.
|
Clamps - Hublock (Relevance 3/10)
Ideal way to attach components to shafts when high torque will be transmitted and a keyway is not disired.
Accommodates large shaft and hub tolerances. Not self centering. Made of alloy steel with black oxide finish for smooth torquing, holding power and surface protection.
|
Collars Threaded - Clamp Type (Relevance 3/10)
Offer full radial holding power without marring the shaft.
|
Fasteners | |
Joints - Clevis - Plastic (Relevance 3/10)
Use with plastic rod ends - Includes pin and clip. See also yokes.
Comes with clevis pin and retaining clip. Corrosion Resistant, Lightweight. High Tensile Strength (Shown in table as Short Term / Long Term). Vibration Dampening / Noise Dampening. (1) Tensile Strengths shown are Maximum Static axial in Newtons.
|
Nuts - Hexagonal - Locking (Relevance 3/10)
By applying torque to the locking screw, a press fit or wave spring effect is created locking female threads of the locknut to the male threads of the shaft.
Produces a strong metal to metal lock. Locking set screws do not protrude through the face of the threads of the locknut, eliminating damage to shaft.
|
Socket Set Screws - Acetal Tipped (Relevance 3/10)
Acetal tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
|
Socket Set Screws - Brass Tipped (Relevance 3/10)
Brass tipped grub screws. Helps to prevent shaft damage on harder shafts.
|
Socket Set Screws - Diamond Knurled Tip (Relevance 3/10)
Grub screws that grip rough shafts.
|
Socket Set Screws - Nylon Tipped (Relevance 3/10)
Nylon tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
|
Gears and Gearing | |
Gears - Spur - Module 0.5 - Stem (Relevance 3/10)
Gears with integral shafts.
Metallic.
|
Gears - Spur - Module 0.75 - Stem (Relevance 3/10)
Gears with integral shafts.
Metallic.
|
Gears - Spur - Module 0.8 - Stem (Relevance 3/10)
Gears with integral shafts.
Metallic.
|
Gears - Spur - Module 1 - Stem (Relevance 3/10)
Gears with integral shafts.
Metallic.
|
Gears - Spur - Module 1.5 - Stem (Relevance 3/10)
Gears with integral shafts.
Metallic.
|
Gears - Spur - Module 2 - Stem (Relevance 3/10)
Gears with integral shafts.
Metallic.
|
Gears - Spur - Module 2.5 - Stem (Relevance 3/10)
Gears with integral shafts.
Metallic.
|
Housings | |
Cross Blocks - Heavy Duty - One Knob One Nut (Relevance 3/10)
Used for connecting two round rods at 90 degrees.
Adjustments can be made by loosening the hand knob. Plastic knobs function independently for precise adjustment. Knobs have brass insert for easy turning and to prevent galling. Stainlesss steel eye bolt firmly clamps around adjusting rod for superior holding strength. Eyelet does not mar rod when tightened, resulting in smooth rod surface that easily slides through the cross block. No set screws required. Plastic or Stainless bodies accept 12.70 or 15.88mm rods.
|
Cross Blocks - Heavy Duty - Two Knobs (Relevance 3/10)
Used for connecting two round rods at 90 degrees.
Adjustments can be made by loosening the hand knob. Plastic knobs function independently for precise adjustment. Knobs have brass insert for easy turning and to prevent galling. Stainlesss steel eye bolt firmly clamps around adjusting rod for superior holding strength. Eyelet does not mar rod when tightened, resulting in smooth rod surface that easily slides through the cross block. No set screws required. Plastic or Stainless bodies accept 12.70 or 15.88mm rods.
|
Cross Blocks - Heavy Duty - Two Nuts (Relevance 3/10)
Used for connecting two round rods at 90 degrees.
Adjustments can be made by loosening the hand knob. Plastic knobs function independently for precise adjustment. Stainlesss steel eye bolt firmly clamps around adjusting rod for superior holding strength. Eyelet does not mar rod when tightened, resulting in smooth rod surface that easily slides through the cross block. No set screws required. Plastic or Stainless bodies accept 12.70 or 15.88mm rods.
|
Linear Ball Splines | |
Linear Ball Splines - Bearings - Flanged (Relevance 3/10)
Use with Linear Ball Spline Shaft.
|
Linear Ball Splines - Bearings - Unflanged (Relevance 3/10)
Use with Linear Ball Spline Shaft.
|
Linear Motion Bearings | |
Bearings - Linear - Ball (Relevance 3/10)
Adjustable and fixed types - open for running on a supported rail and closed for fixed shafts.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 Deg C Intermittent, 80 Deg C continuous.
|
Bearings - Linear - Ball - Thomson Precision Steel (Closed) (Relevance 3/10)
For running on shafts fixed at the ends.
|
Bearings - Linear - Ball - Thomson Precision Steel (Open) (Relevance 3/10)
For running on shafts supported by a rail along their length.
|
Bearings - Linear - Ball - Thomson Super (Closed) (Relevance 3/10)
For running on shafts fixed at the ends.
|
Bearings - Linear - Ball - Thomson Super (Open) (Relevance 3/10)
For running on shafts supported by a rail along their length.
|
Bearings - Linear - Ball - Thomson Super Smart (Closed) (Relevance 3/10)
For running on shafts fixed at the ends.
|
Bearings - Linear - Ball - Thomson Super Smart (Open) (Relevance 3/10)
For running on shafts supported by a rail along their length.
|
Bushings - Stroke Rotary - Miniature (Relevance 3/10)
2 to 12mm Shaft Sizes. Can operate in both linear and rotary directions at the same time.
Set includes outer ring, ball cage and shaft. Ball Cage: Brass Balls: Hard Steel / Shaft: Hard Steel Outer Ring: Hard Steel. Temperature: +100°C (Constant), +120°C (Maximum). Stroke: = (L1 - Lb) x 2. Supplied with extreme accuracy with zero to minimum preload.
|
Linear Motion Bearings - Drylin Bushings | |
Drylin Sliding Bearings (Relevance 3/10)
Linear sliding motion. Use with Drylin Aluminium Shafts.
Sliding film Iglidur J. Maximum Mean Surface Pressure: 25 N/mm2. Highest Wear Resistance at loads: < 2 N/mm2. Maximum Speed: 8 m/s (dry) >10 m/s (lubricated) 1.5 m/s (rotating dry). Working Temp. Range: -60°C to +100°C (increased wear when used in excess of 80°C).
|
Drylin Sliding Film (Relevance 3/10)
Linear sliding motion. Use with Drylin Aluminium Shafts.
Sliding film Iglidur J.
|
Spacers | |
Spacers - Round - Through Bore - Aluminium (Relevance 3/10)
Shaft spacers - Aluminium
|
Spacers - Round - Through Bore - Brass (Relevance 3/10)
Shaft spacers - Brass
|
Spacers - Round - Through Bore - Nylon (Relevance 3/10)
Shaft spacers - Nylon
|
Spacers - Round - Through Bore - Stainless Steel (Relevance 3/10)
Shaft spacers - Stainless Steel
|
Spacers - Round - Through Bore - Steel (Relevance 3/10)
Shaft spacers - Steel
|
Washers | |
Washers - Lock - Internal Tooth - Spring Steel (Relevance 3/10)
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Internal Tooth - Stainless Steel (Relevance 3/10)
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
|
Bearings - Specialty | |
Bearings - Ball - 316 Stainless Steel (Relevance 1/10)
Food and Medical grade Stainless Steel - Non Hardenable.
Tolerances differ from standard bearing types - see below. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. ID +0.0762 mm / -0.000 mm OD +0.000 mm / -0.0762 mm Width +/- 0.127 mm. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races.
|
Bearings - One Way - Roller (Relevance 1/10)
Roller Clutch Bearings rotate in one direction only.
Recommended Shaft Diameter for Clutch Bearings without Inner Ring is +0.000 / -0.005 mm.
|
Bearings and Housings | |
Bearings - Press - Acetal - Flange Mounted (Relevance 1/10)
Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Bearing : PTFE Filled Acetal Self Lubricating / -40 to 150 Deg C. Self lubricating. Use any shaft material with 0.4 um or finer finish.
|
Bearings - Press - Needle Roller - Flange Mounted (Relevance 1/10)
Fitted with drawn cup needle bearing. -30 to 110 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Shafts must be hardened to Rc 58 with 0.8um surface finish or finer.
|
Bearings - Press - Sintered Bronze (Relevance 1/10)
Self lubricating. -28 to +95 Deg C. Use any shaft material with 0.8 um or finer finish. Self aligning +/- 5 Degress.
|
Bearings - Press - Sintered Bronze - Flange Mounted (Relevance 1/10)
Porous sintered bronze bearing. -28 to 95 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Use any shaft material with 0.8 um or finer finish.
|
Clamping and Locking | |
Bushings - Integral Taper (Relevance 1/10)
Stainless Steel Taper Bushings.
Will not mar shafts.
|
Bushings - Locking Hub (Relevance 1/10)
Friction grip construction.
Connects rotating components to shafts. Transmits high torque without keyways. Two styles - see diagrams.
|
Clamps - Gear - Two Piece - Commercial Balanced (Relevance 1/10)
Commercial - Stainless - Aluminium - Carbon Steel - For our clamp type gears.
Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. These clamps are designed to clamp the OD of the hub on our clamp type gears. The shaft size listed is for reference only.
|
Clamps - Gear - Two Piece - Precision Balanced (Relevance 1/10)
Precision - Stainless - Aluminium - Carbon Steel - For our clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. These clamps are designed to clamp the OD of the hub on our clamp type gears. The shaft size listed is for reference only.
|
Grips - Taper (Relevance 1/10)
Duroplastic FS31 black. Axle and threaded bush in Steel. Surface Finish: All edges smoothed and highly polished. To assemble unscrew shaft. The grips fit the disk handwheels with revolving taper grip.
|
|
