Pins Dowel Standard 316 Stainless Rounded Both Ends Categories


Category Matches

Pins Dowel

TopHide Pictures

Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends
Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends

Search Rating: 75%

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 316 Grade - DIN7

Diameter tolerances are m6. Also known as parallel pins.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends.

Pins - Dowel - Standard - 303-304 Stainless - Rounded Both Ends
Pins - Dowel - Standard - 303-304 Stainless - Rounded Both Ends

Search Rating: 69%

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 303/304 Grade Stainless- DIN7

Rounded end dowel pins are measured from the start of the edge rounding. This allows the pin to completely fill the hole after you grind off the rounded end. Diameter tolerances are m6. Also known as parallel pins.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Standard - 303-304 Stainless - Rounded Both Ends.

Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends
Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends

Search Rating: 54%

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - DIN7

Diameter tolerances are m6. Also known as parallel pins.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends.

Pins - Hammer Drive - Round Head - Stainless Steel
Pins - Hammer Drive - Round Head - Stainless Steel

Search Rating: 53%

Also see combined categories:
All Hammer Drive Pins

Used to replace screws where the need to remove the pin is unlikely.

Stainless Steel 304 Grade. Simple, low cost assembly. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Hammer Drive - Round Head - Stainless Steel.

Pins - Dowel - Standard - 316 Stainless - Chamfered End
Pins - Dowel - Standard - 316 Stainless - Chamfered End

Search Rating: 52%

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 316 Grade - DIN6325, ISO2338

Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Standard - 316 Stainless - Chamfered End.

Pins - Dowel - Standard - 416 Stainless - Chamfered End
Pins - Dowel - Standard - 416 Stainless - Chamfered End

Search Rating: 46%

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 416 Grade - DIN6325, ISO2338

Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Standard - 416 Stainless - Chamfered End.

Pins - Dowel - Standard - 303-304 Stainless - Chamfered End
Pins - Dowel - Standard - 303-304 Stainless - Chamfered End

Search Rating: 46%

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 303/304 Grade Stainless - DIN6325, ISO2338

Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Standard - 303-304 Stainless - Chamfered End.

Keys and Keysteel

TopHide Pictures

Keys - Machine - Stainless Steel
Keys - Machine - Stainless Steel

Search Rating: 37%

Also see combined categories:
All Machine Keys

Form A has rounded ends. Form B has square ends. Form AB has one end rounded and one end square. DIN6884


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Keys - Machine - Stainless Steel.

Pins Roll

TopHide Pictures

Pins - Coiled - Stainless Steel - Standard Duty
Pins - Coiled - Stainless Steel - Standard Duty

Search Rating: 37%

Also see combined categories:
All Coiled Pins

Spirol Pins. Coiled roll pin.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Coiled - Stainless Steel - Standard Duty.

Collars

TopHide Pictures

Collars - Shaft - Standard - Stainless Steel
Collars - Shaft - Standard - Stainless Steel

Search Rating: 36%

Also see combined categories:
All Round Bore Shaft Collars
All Standard Shaft Collars

Includes miniature precision types. 303 and 316 Types.

Static torque and axial load are for reference only using steel cup point grub screw on soft steel shaft.

Related Information:

Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Collars - Shaft - Standard - Stainless Steel.

Mounts Leveling

TopHide Pictures

Mounts - Leveling - Hygienic - 304 Stainless Steel
Mounts - Leveling - Hygienic - 304 Stainless Steel

Search Rating: 36%

Also see combined categories:
All Pivotal Levelers
All Mounting Feet

ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications. Adjusters.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Mounts - Leveling - Hygienic - 304 Stainless Steel.

Screws Grub (Socket Set)

TopHide Pictures

Socket Set Screws - Cup Point - Standard - 316 Stainless Steel - DIN916
Socket Set Screws - Cup Point - Standard - 316 Stainless Steel - DIN916

Search Rating: 36%

Also see combined categories:
All Grub Screws

Standard grub screws. UNC - UNF - BA - METRIC.

Related Information:

Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Socket Set Screws - Cup Point - Standard - 316 Stainless Steel - DIN916.

Balls Metallic

TopHide Pictures

Balls - Stainless Steel - 316L Grade
Balls - Stainless Steel - 316L Grade

Search Rating: 35%

Also see combined categories:
All Metallic Balls

Easier to machine than standard 316 grade.

316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.

Related Information:

Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Balls - Stainless Steel - 316L Grade.

Mounts Leveling

TopHide Pictures

Mounts - Leveling - Hygienic - Anchoring - One Hole
Mounts - Leveling - Hygienic - Anchoring - One Hole

Search Rating: 35%

Also see combined categories:
All Pivotal Levelers
All Mounting Feet

ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications. Adjusters.

Operating temperature -20 to 100o C. Rubber base meets FDA 177-2600. 5o swivel for good floor contact.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Mounts - Leveling - Hygienic - Anchoring - One Hole.

Mounts - Leveling - Hygienic - Anchoring - Two Hole
Mounts - Leveling - Hygienic - Anchoring - Two Hole

Search Rating: 35%

Also see combined categories:
All Pivotal Levelers
All Mounting Feet

ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications. Adjusters.

Operating temperature -20 to 100o C. Rubber base meets FDA 177-2600. 5o swivel for good floor contact.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Mounts - Leveling - Hygienic - Anchoring - Two Hole.

Cable

TopHide Pictures

Attachments - Thimbles - Stainless Steel
Attachments - Thimbles - Stainless Steel

Search Rating: 35%

316 Stainless Steel. Use with synchromesh cable or standard miniature cable. Use with synchromesh or standard miniature cable

Thimbles provide loop support at higher loads and protect cables from wear when motion is present. Some thimbles may have open or uneven ends.

Related Information:

Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Attachments - Thimbles - Stainless Steel.

Mounts Leveling

TopHide Pictures

Mounts - Leveling - Hygienic - Anchoring - Low Profile - High Swivel
Mounts - Leveling - Hygienic - Anchoring - Low Profile - High Swivel

Search Rating: 35%

Also see combined categories:
All Pivotal Levelers
All Mounting Feet

ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications. Adjusters.

Operating temperature -20 to 100o C. Wrench flats in thread still allow for full use of threaded section. 12o swivel.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Mounts - Leveling - Hygienic - Anchoring - Low Profile - High Swivel.

Mounts - Leveling - Hygienic - Anchoring - Low Profile - Low Swivel
Mounts - Leveling - Hygienic - Anchoring - Low Profile - Low Swivel

Search Rating: 35%

Also see combined categories:
All Pivotal Levelers
All Mounting Feet

ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications. Adjusters.

Operating temperature -20 to 100o C. Wrench flats in thread still allow for full use of threaded section. 1o swivel.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Mounts - Leveling - Hygienic - Anchoring - Low Profile - Low Swivel.

Bearings for Housings

TopHide Pictures

Bearings - 316 Stainless Steel - Spherical OD - For Plastic Housings
Bearings - 316 Stainless Steel - Spherical OD - For Plastic Housings

Search Rating: 35%

Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.

Load and speed calculations are for reference only. Testing is recommended.

Related Information:

Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bearings - 316 Stainless Steel - Spherical OD - For Plastic Housings.

Shim

TopHide Pictures

Feeler Gauge Stock - Stainless
Feeler Gauge Stock - Stainless

Search Rating: 34%

Used for close spacing and extremely tight tolerance situation.

Rc45-55 hardness. 300 grade stainless. Short flat lengths have rounded ends and are marked for size. Coiled lengths are etched every 6 inches and can be easily cut to length. 12.7mm wide.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Feeler Gauge Stock - Stainless.

Pins Taper

TopHide Pictures

Pins - Taper - Imperial - Extractable - External Thread - Stainless Steel
Pins - Taper - Imperial - Extractable - External Thread - Stainless Steel

Search Rating: 34%

Also see combined categories:
All Imperial Taper Pins

Imperial Sizes Tapered 1:48 (1/4 in. per foot). Standard sizes numbers 0 to 14.

Threaded externally for easy extraction.

Related Information:

Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Taper - Imperial - Extractable - External Thread - Stainless Steel.

Keys and Keysteel

TopHide Pictures

Keysteel Lengths - Rectangular - Stainless Steel
Keysteel Lengths - Rectangular - Stainless Steel

Search Rating: 33%

Also see combined categories:
All Keysteel Lengths

303, 304 and 316 key steel

Use oversized for replacing keys where the keyway may be slightly worn - standard aftermarket keysteel. Use undersized for manufacturing and new applications where the keyway tolerances can be controlled.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Keysteel Lengths - Rectangular - Stainless Steel.


Show all items starting with
A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z   1   2   3   4   5   6   7   8   9  





Other Store Pages

Click Page Banner Below

Top

Main Pages

Click Page Banner Below

Top





Top



Freight Rates
Terms and Conditions
Privacy Policy

Miniature Bearings Australia offers 123430 products in 2841 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.