Pins Dowel Bushings Categories


Category Matches

Pins Dowel

TopHide Pictures

Pins - Dowel Bushings
Pins - Dowel Bushings

Search Rating: 100%

Also see combined categories:
All Dowel Bushings

Series DB100 Spirol

Spring Steel. Precision rolled bushes manufactured from spring steel. Designed to eliminate the need for separate dowling where two components are to be located accurately together and fastened with bolts. They are available for use with bolts from M5 to M12.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel Bushings.

Tension Bushings

TopHide Pictures

Bushings - Tension
Bushings - Tension

Search Rating: 65%

Like a heavy duty roll pin.

Made of a high carbon spring steel with high elasticity, resilience and wear characteristics. Designed to replace solid steel tubular and case hardened bushings because they are close tolerance, self-retaining and through hard. Insertion can be easily accomplished with a hammer and drift. Ideal for high load/low-speed operation in articulating or continuous applications.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bushings - Tension.

Latches Draw

TopHide Pictures

Latches - Draw - Soft
Latches - Draw - Soft

Search Rating: 57%

Tolerates misalignment. UV resistant thermoplastic elastomer body. Glass reinforced nylon link and bushings. Stainless steel rivet, pins, keeper and brackets. Cushions impact and absorbs vibration.

Keeper included.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Latches - Draw - Soft.

Clamping Bushings

TopHide Pictures

Bushings - Shoulder
Bushings - Shoulder

Search Rating: 52%

Mould components


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bushings - Shoulder.

Pins Dowel

TopHide Pictures

Pins - Dowel - Extractable
Pins - Dowel - Extractable

Search Rating: 52%

Also see combined categories:
All Dowel Pins

Hardened and Ground Steel 100 Cr6. Din 7979.

Extractable dowels have a thread tapped in the end to fascilitate removal from blind holes. An air release flat is ground along the full length of the pin to overcome the problem of pressure build up by trapped air. Hardness 55-62 HRC, HV550-650. Extractable pins may or may not have a flat to vent pressure when pulling. Also known as parallel pins.

Related Information:

Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Extractable.

Pins - Dowel - Extractable - With Vent
Pins - Dowel - Extractable - With Vent

Search Rating: 52%

Also see combined categories:
All Dowel Pins

Hardened and Ground Steel 100 Cr6 with a ground flat along one edge

Extractable dowels have a thread tapped in the end to fascilitate removal from blind holes. An air release flat is ground along the full length of the pin. Hardness 55-62 HRC, HV550-650. Also known as parallel pins.

Related Information:

Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Extractable - With Vent.

Pins - Dowel - Standard - 303-304 Stainless - Chamfered End
Pins - Dowel - Standard - 303-304 Stainless - Chamfered End

Search Rating: 52%

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 303/304 Grade Stainless - DIN6325, ISO2338

Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Standard - 303-304 Stainless - Chamfered End.

Pins - Dowel - Standard - 303-304 Stainless - Rounded Both Ends
Pins - Dowel - Standard - 303-304 Stainless - Rounded Both Ends

Search Rating: 52%

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 303/304 Grade Stainless- DIN7

Rounded end dowel pins are measured from the start of the edge rounding. This allows the pin to completely fill the hole after you grind off the rounded end. Diameter tolerances are m6. Also known as parallel pins.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Standard - 303-304 Stainless - Rounded Both Ends.

Pins - Dowel - Standard - 316 Stainless - Chamfered End
Pins - Dowel - Standard - 316 Stainless - Chamfered End

Search Rating: 52%

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 316 Grade - DIN6325, ISO2338

Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Standard - 316 Stainless - Chamfered End.

Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends
Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends

Search Rating: 52%

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 316 Grade - DIN7

Diameter tolerances are m6. Also known as parallel pins.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends.

Pins - Dowel - Standard - 416 Stainless - Chamfered End
Pins - Dowel - Standard - 416 Stainless - Chamfered End

Search Rating: 52%

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 416 Grade - DIN6325, ISO2338

Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Standard - 416 Stainless - Chamfered End.

Pins - Dowel - Standard - Chamfered End
Pins - Dowel - Standard - Chamfered End

Search Rating: 52%

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - DIN6325, ISO2338

Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Standard - Chamfered End.

Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends
Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends

Search Rating: 52%

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - DIN7

Diameter tolerances are m6. Also known as parallel pins.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends.

Pins - Groove
Pins - Groove

Search Rating: 51%

Also see combined categories:
All Groove Pins

Non threaded press fit fastener that doesn't require a reamed hole as do dowel pins.Commonly used in place of taper pins.

An economic method of fastening without the need for precision drilled and reamed holes. Recommended hole tolerance is H11. Total length may be slightly longer than the nominal length. Expanded portion of the pin is compressed into the hole a few thousands of an inch wider than the nominal pin diameter. Radial forces lock the pin securely into the drilled hole.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Groove.

Pins - Hammer Drive - Flat Head
Pins - Hammer Drive - Flat Head

Search Rating: 51%

Also see combined categories:
All Hammer Drive Pins

Used to replace screws where the need to remove the pin is unlikely.

Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Hammer Drive - Flat Head.

Pins - Hammer Drive - Round Head - Stainless Steel
Pins - Hammer Drive - Round Head - Stainless Steel

Search Rating: 50%

Also see combined categories:
All Hammer Drive Pins

Used to replace screws where the need to remove the pin is unlikely.

Stainless Steel 304 Grade. Simple, low cost assembly. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Pins - Hammer Drive - Round Head - Stainless Steel.

Bushes Plastic

TopHide Pictures

Bushings - Snap - Closed
Bushings - Snap - Closed

Search Rating: 49%

Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Open snap bushings are designed to provide protection from sharp edges where cable or hose runs through plate steel.

Similar to a bung, but designed with expanding catch for use in holes in sheet products. Also see grommets for a similar product made from rubber.

Related Information:

Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bushings - Snap - Closed.

Bushings - Snap - Open
Bushings - Snap - Open

Search Rating: 49%

Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Closed snap bushings are designed to keep out dust and other contaminants and protect from sharp edges where cable or hose used to run through a hole in plate steel.

Also called a dome plug. Also see grommets for a similar product made from rubber.

Related Information:

Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bushings - Snap - Open.

Bushings - QD and Taperlock

TopHide Pictures

Bushings - QD
Bushings - QD

Search Rating: 47%

Used with QD type cast iron vee pulleys, timing pulleys, sprockets, poly vee pulleys and other parts designed specifically for use with a QD bushing

Similar to a taperlock bush, but not interchangeable. QD bushings like taperlock bushings allow for use of a single stock pulley for many applications with different shaft sizes. Select the correct QD series to suit the pulley.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bushings - QD.

Bushings - Taperlock
Bushings - Taperlock

Search Rating: 46%


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bushings - Taperlock.

Bushings Spherical

TopHide Pictures

Bushings - Spherical - Plastic
Bushings - Spherical - Plastic

Search Rating: 46%

Also see combined categories:
All Spherical Bushings

Plastic spherical plain bearings. Also known as ball bushings.

Ball Material W300. Housing Iglidur G. Maintenance Free. Self lubricating. Compensates for axial loads and misalignment. Corrosion resistant. High vibration dampening capacity.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bushings - Spherical - Plastic.

Bushings - Spherical - Steel
Bushings - Spherical - Steel

Search Rating: 46%

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bushings - Spherical - Steel.

Bushings - Spherical - Steel - With Oil Hole
Bushings - Spherical - Steel - With Oil Hole

Search Rating: 46%

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bushings - Spherical - Steel - With Oil Hole.

Bushings - Spherical - Steel - With Oil Hole and Wiper Seal
Bushings - Spherical - Steel - With Oil Hole and Wiper Seal

Search Rating: 46%

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bushings - Spherical - Steel - With Oil Hole and Wiper Seal.

Bushings - Spherical - Steel - With Wiper Seal
Bushings - Spherical - Steel - With Wiper Seal

Search Rating: 46%

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bushings - Spherical - Steel - With Wiper Seal.

Fastening Bushings

TopHide Pictures

Bushings - Drill - Liner Type - Headless
Bushings - Drill - Liner Type - Headless

Search Rating: 46%

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bushings - Drill - Liner Type - Headless.

Bushings - Drill - Press-fit - Headless
Bushings - Drill - Press-fit - Headless

Search Rating: 46%

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bushings - Drill - Press-fit - Headless.

Bushings - Drill - Press-fit - Headless - Tungsten Carbide
Bushings - Drill - Press-fit - Headless - Tungsten Carbide

Search Rating: 46%

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bushings - Drill - Press-fit - Headless - Tungsten Carbide.

Bushings - Drill - Press-fit - Standard Head
Bushings - Drill - Press-fit - Standard Head

Search Rating: 46%

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bushings - Drill - Press-fit - Standard Head.

Bushings - Drill - Slip - With Head
Bushings - Drill - Slip - With Head

Search Rating: 46%

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bushings - Drill - Slip - With Head.

Stroke Rotary Bushings

TopHide Pictures

Bushings - Stroke Rotary - Miniature
Bushings - Stroke Rotary - Miniature

Search Rating: 46%

Also see combined categories:
All Stroke Rotary Bushings

2 to 12mm Shaft Sizes. Can operate in both linear and rotary directions at the same time.

Set includes outer ring, ball cage and shaft. Ball Cage: Brass Balls: Hard Steel / Shaft: Hard Steel Outer Ring: Hard Steel. Temperature: +100oC (Constant), +120oC (Maximum). Stroke: = (L1 - Lb) x 2. Supplied with extreme accuracy with zero to minimum preload.

Related Information:

Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bushings - Stroke Rotary - Miniature.

Dual Vee Bearings

TopHide Pictures

Dual Vee - Adaptor Bushings
Dual Vee - Adaptor Bushings

Search Rating: 46%

Also see combined categories:
All Dual Vee Guide Wheels

Vee grooved track roller bushings.

Stationary bushings have a concentric hole. Adjustable bushings have an eccentric hole allowing positioning of the guide wheel as the bush is turned.

Related Information:

Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Dual Vee - Adaptor Bushings.

Spacers

TopHide Pictures

Spacers - Machinery Bushings
Spacers - Machinery Bushings

Search Rating: 45%

Also see combined categories:
All Round Spacers
All Flat Washers and Spacers - Metallic

Used as spacers between pulleys, gears etc

Low carbon mild steel.


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Spacers - Machinery Bushings.

Cam Followers

TopHide Pictures

Cam Followers - Self Lubricating - Bronze Bushing
Cam Followers - Self Lubricating - Bronze Bushing

Search Rating: 45%

Also see combined categories:
All Cam Followers


Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Cam Followers - Self Lubricating - Bronze Bushing.

Bushes Plastic

TopHide Pictures

Bushes - Plastic - Iglidur G - Flanged
Bushes - Plastic - Iglidur G - Flanged

Search Rating: 45%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

Small Parts and Bearings website has a good range of specialty engineering products. Check it now for a possible expanded range of Bushes - Plastic - Iglidur G - Flanged.


Show all items starting with
A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z   1   2   3   4   5   6   7   8   9  





Other Store Pages

Click Page Banner Below

Top

Main Pages

Click Page Banner Below

Top





Top



Freight Rates
Terms and Conditions
Privacy Policy

Miniature Bearings Australia offers 123442 products in 2844 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Miniature Bearings Australia is part of MBA Group offering a select range from the MBA Group catalogue.

Miniature Bearings Australia products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Miniature Bearings Australia 1997. All rights reserved.