Categories that include the term: DRYLIN
|
Linear Motion Bearings - Drylin |  |
Linear Slide - Drylin - Accessories (Relevance 10/10)
Insensitive to dust and dirt.
Carriage blocks and half slide rail. Make your own custom sized assemblies. Replace blocks on carriage assemblies. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.
|
Linear Slide - Drylin - Carriage Assembly (Relevance 10/10)
Insensitive to dust and dirt. Match with Drylin Rail sold seperately.
Match size 1 assembly with size 1 rail or size 2 assembly with size 2 rail. Flat and wide for supporting high moments. Low friction value for dry running. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.
|
Linear Slide - Drylin - Rail (Relevance 10/10)
Insensitive to dust and dirt. Match with Drylin Carriage Assembly sold seperately.
Match size 1 assembly with size 1 rail or size 2 assembly with size 2 rail. Flat and wide for supporting high moments. Low friction value for dry running. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.
|
Linear Motion Bearings - Drylin Assemblies | |
Drylin Linear Assembly Parts - Carriage Only (Relevance 10/10)
Linear sliding motion. Plain and Locking Types. These carriages require a matching guide rail or matching rack and pinion. Match by size.
Drylin® T linear guides are maintenance free and run without additional lubrication. Consequently, they are also suitable for use in damp or dirty environments. Available with a manually operated clamp to achieve a force fit at any desired point along the travel path. The wing screw is used to clamp the slide in place of the guide. Matching components listed in separate category.
|
Drylin Linear Assembly Parts - Guide Rails Only (Relevance 10/10)
These rails require a matching carriage as listed in a separate category. Match by size.
Slide Rail: Extruded Aluminium Construction Material: Al Mg Si 0.5. Coating: Hard anodised, 50µm Hardness: 500HV. Matching components listed in separate category.
|
Drylin Linear Assembly Parts - Pinion Assembly Only (Relevance 10/10)
These pinion assemblies require a matching carriage and rack as listed in separate categories. Match by size.
Pinion Assembly Body: Aluminium. Gear: Stainless steel. Bearings: Steel. Working Temperature Range: 0°C to +60°C. Designed to be attached to TW carriages using specific rack rail.
|
Drylin Linear Assembly Parts - Rack and Rail Only (Relevance 10/10)
These rack and rails require a matching carriage and pinion assembly as listed in separate categories. Match by size.
Working Temperature Range: 0°C to +60°C. Available in 500mm lengths. Slide Rail: Extruded Aluminium Construction Material: Al Mg Si 0.5. Coating: Hard anodised, 50µm Hardness: 500HV. Refer to Standard Rail for basic dimensions.
|
Linear Motion Bearings - Drylin Bushings | |
Drylin Sliding Bearings (Relevance 10/10)
Linear sliding motion. Use with Drylin Aluminium Shafts.
Sliding film Iglidur J. Maximum Mean Surface Pressure: 25 N/mm2. Highest Wear Resistance at loads: < 2 N/mm2. Maximum Speed: 8 m/s (dry) >10 m/s (lubricated) 1.5 m/s (rotating dry). Working Temp. Range: -60°C to +100°C (increased wear when used in excess of 80°C).
|
Drylin Sliding Film (Relevance 10/10)
Linear sliding motion. Use with Drylin Aluminium Shafts.
Sliding film Iglidur J.
|
Linear Motion Bearings - Drylin Slides | |
Drylin - Linear - Slides and Carriages - Size 17 (Relevance 10/10)
Linear sliding motion.
Guide Rail Weight: 150 g/m. Carriage Weight: 1.7g. Max Rail Length: 1960 mm. Standard Bore Scheme: Symmetrical C5 = C6. Particularly insensitive to dust, dirt and water.
|
Drylin - Linear - Slides and Carriages - Size 27 (Relevance 10/10)
Linear sliding motion.
Guide Rail Weight: 290 g/m. Carriage Weight: 10.8 or 12.5g. Max Rail Length: 2000 mm. Standard Bore Scheme: Symmetrical C5 = C6. Particularly insensitive to dust, dirt and water.
|
Drylin - Linear - Slides and Carriages - Size 80 (Relevance 10/10)
Linear sliding motion.
Guide Rail Weight: 1140 g/m. Carriage Weight: 100g. Max Rail Length: 2000 mm. Standard Bore Scheme: Symmetrical C5 = C6. Particularly insensitive to dust, dirt and water.
|
Shaft and Shafting | |
Shafting - Aluminium (Relevance 3/10)
Drylin aluminium shafting is recommended for use with Igubal Drylin bearings only.
Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: >40µm. Surface Hardness: 450-550 HV. Roughness: Ra<0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: ph between 2 and 9.
|
Shafting - Pipe - Aluminium (Relevance 3/10)
Recommended for use with Igubal Drylin bearings only.
Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: >40µm. Surface Hardness: 450-550 HV. Roughness: Ra<0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: 2
|
Shafting - Supported - Pre-Drilled - Aluminium (Relevance 3/10)
For Drylin Bearings.
Material : AlMgSi 0.5 F22. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: >40µm. Surface Hardness: 450-550 HV. Roughness: Ra<0.5. Spec. Electr. Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: 2
|
Housings with Integral Bearing | |
Housings - Igubal - Sliding (Relevance 1/10)
Housing: Aluminium. Insert: Sliding film Iglidur® J. Tolerance for the Shaft: h7. Use with Drylin aluminium shafts.
|
Linear Drive Systems - Leadscrew | |
Actuator - Leadscrew - Low Profile (Relevance 1/10)
Lead = Travel per revolution of screw. Rail, Carriage Plate and End Blocks: Aluminium Carriage Blocks: Die cast Zinc. Leadscrew: Steel. Bearings: Self lubricating DryLin® Plastic. Max. Permissible Radial Load: 2,800N (Static), 2,000N (Dynamic). Max. Permissible Thrust Load: 700N (Static), 0,23 MPa x m/s (Dynamic Trapezoidal Leadscrew), 0.08 x m/s (Axial Bearing).
|
No more categories match your selection
|
