Catalogue Index - Categories beginning with C
|
C Section V Belts |  |
Belts - Vee - 22.0 x 14.0 mm - C
22.0mm Top Width x 14.0mm Height.
|
Belts - Vee - 22.0 x 18.0 mm - SPC
22.0mm Top Width x 18.0mm Height.
|
Cable | |
Attachments - Ball Plugs
|
Attachments - Eyes - Synchromesh
|
Attachments - Loop Sleeves
|
Attachments - Plugs - Synchromesh
|
Attachments - Thimbles
|
Attachments - Threaded Plugs
|
Cable - Miniature
Nylon coated Stainless Steel.
Recommended that nylon coating is stripped prior to swaging. Sold per 300mm length. Multiple quantities will be supplied in a continuous length up to 3mtr maximum.
|
Cable - Synchromesh
Pitch Error ±0.050 mm. Cumulative Pitch Error ±4.070 mm max. over 100 pitches. Temperature Range = -30 Deg. Celcius to +80 Deg. Celcius. Avoid strong acids, alkalies and organic solvents.
|
Tools - Crimping
For crimping loop sleeves, plugs and eyes used with miniature cable.
|
Cable - Synchromesh - Pulleys To Suit | |
Pulleys - Synchromesh
|
Caged Type Needle Roller Bearings | |
Bearings - Needle Roller - Cage Type
Cage and Rollers.
|
Cam Followers - Ball Type | |
Cam Followers - Ball Type
Stainless steel ball type cam followers.
|
Cam Followers - Roller Type | |
Cam Followers - Roller Type - Easy Mounting
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
|
Cam Followers - Roller Type - Eccentric Stud
Carbon steel roller type cam followers with eccentric stud.
Carbon Steel - Synthetic rubber seals assembled in the outer ring. Screwdriver slot for mounting. Stud designed to fit H7 housing.
|
Cam Followers - Roller Type - Miniature - Standard
Small carbon steel roller type cam followers.
Carbon Steel - Nitrile Rubber seals assembled in the outer ring. Screwdriver slot for mounting. Stud designed to fit H7 housing.
|
Cam Followers - Roller Type - Miniature - Thrust Disc
Small carbon steel thrust disc roller type cam followers.
CFS.. W: High Carbon Steel (all parts). CFS.. FW: Stainless Steel - hard, similar to 440C (all parts). Stud designed to fit H7 housing.
|
Cam Followers - Roller Type - Stainless Steel
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
|
Cam Followers - Roller Type - Standard
Carbon steel roller type cam followers.
Load 1 applies when outer race is mounted into a housing with standard bearing fit. Load 2 applies when used as a track roller. Stud designed to fit H7 housing.
|
Cam Followers - Roller Type - Thrust Disc
Carbon steel thrust disc roller type cam followers.
CF..WBR, CF..WBUUR: High Carbon Steel. CF..FWBR, CF..FWBUUR: Stainless Steel. Seals: Synthetic Rubber. Stud designed to fit H7 housing.
|
Cam Locks | |
Locks - Cam
|
Cams | |
Cams
|
Cams - Adjustable
|
Cap Head Socket Screws | |
Screws - Socket - Cap - Alloy Steel
UNC - UNF - METRIC - Alloy Steel.
|
Screws - Socket - Cap - Alloy Steel - Assortment Kit
|
Screws - Socket - Cap - Aluminium
Variety of colours available.
|
Screws - Socket - Cap - Molybdenum Disulphide Coated
UNC - UNF - METRIC.
|
Screws - Socket - Cap - Nylon
UNC - UNF - METRIC - Non Conductive - Non Magnetic.
|
Screws - Socket - Cap - Stainless
UNC - UNF - METRIC - Stainless Steel.
|
Screws - Socket - Cap - Titanium
METRIC. CP Grade 1.
|
Screws - Socket - Cap - Zinc Plated
UNC - UNF - METRIC - Alloy Steel.
|
Screws - Socket - Low Head
UNC - UNF - METRIC - Alloy Steel.
|
Screws - Socket - Tapered Head - Titanium
6AL-4V (Grade 5) High strength titanium alloy.
|
Cap Screws - Socket Head | |
Screws - Socket - Cap - Alloy Steel
UNC - UNF - METRIC - Alloy Steel.
|
Screws - Socket - Cap - Alloy Steel - Assortment Kit
|
Screws - Socket - Cap - Aluminium
Variety of colours available.
|
Screws - Socket - Cap - Molybdenum Disulphide Coated
UNC - UNF - METRIC.
|
Screws - Socket - Cap - Nylon
UNC - UNF - METRIC - Non Conductive - Non Magnetic.
|
Screws - Socket - Cap - Stainless
UNC - UNF - METRIC - Stainless Steel.
|
Screws - Socket - Cap - Titanium
METRIC. CP Grade 1.
|
Screws - Socket - Cap - Zinc Plated
UNC - UNF - METRIC - Alloy Steel.
|
Screws - Socket - Low Head
UNC - UNF - METRIC - Alloy Steel.
|
Screws - Socket - Tapered Head - Titanium
6AL-4V (Grade 5) High strength titanium alloy.
|
Cap Style Brakes - Power Off | |
Brakes - Cap Style - Power Off
Brake loads in absence of power.
|
Captive Thumb Screws | |
Screws - Thumb - Captive
Brass.
|
Carbon Fibre Materials | |
Bar - H - Carbon Fibre
High impact light weight carbon fibre for modelling.
|
Rod - Round - Carbon Fibre
High impact light weight carbon fibre for modelling.
|
Strip - Carbon Fibre
High impact light weight carbon fibre for modelling.
|
Tube - Rectangular - Carbon Fibre
High impact light weight carbon fibre for modelling.
|
Tube - Round - Carbon Fibre
High impact light weight carbon fibre for modelling.
|
Tube - Square - Carbon Fibre
High impact light weight carbon fibre for modelling.
|
Carbon Spring Steel | |
Washers - Flat - Carbon Spring Steel - Precision
Flat Carbon Spring Steel Washers.
|
Washers - Spring
Wave Washers - All Materials.
|
Carbon Steel Bar | |
Bar - Hexagonal - Carbon Steel
|
Bar - Square - Carbon Steel
|
Carriage Assemblies | |
Carriage Assemblies - Utilitrak
Use with Utilitrak Guiderails
|
Guide Rails - Utilitrak
Use with Carriage Assemblies - Utilitrak
|
Carry Mountings - Leveling | |
Mounts - Leveling Carry - Ball Type
Vibration Dampening with retractable ball for movement.
|
Mounts - Leveling Carry - Castor Type
Vibration Dampening with castor for movement.
|
Cast Iron Bearing Housings | |
Bearings - For Cast Iron Housings
With spherical OD for use with cast iron flanged and pillow block housings.
|
Housings - Bearing - Flanged - 2 Bolt Hole - Cast Iron
|
Housings - Bearing - Flanged - Offset - Cast Iron
|
Housings - Bearing - Flanged - Round - Cast Iron
|
Housings - Bearing - Flanged - Square - Cast Iron
|
Housings - Bearing - Pillow Block - Cast Iron
|
Castor Type Mountings - Leveling | |
Mounts - Leveling Carry - Castor Type
Vibration Dampening with castor for movement.
|
Catalogues | |
Catalogues
Hardcopy, CD and PDF catalogues. Including the popular Machinery Handbook.
Information to assist in the selection of our products.
|
C-Clips | |
C-Clips
Variation of an E-Clip with an open face.
Narrow section height provides good clearance capabilities. Absence of teeth and deep set mean less thrust load ratings than e-clips. For best results install using the recommended applicator tool.
|
Centrebolt Mounts - Solo Unitised | |
Mounts - Vibration - Centre Bolt - Solo Unitised
|
Ceramic Balls | |
Balls - Ceramic - Silicon Nitride
Outstanding wear resistance. Good thermal and chemical resistance.
|
Balls - Ruby - Synthetic
Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.
|
Balls - Sapphire - Synthetic
Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.
|
Hobby Balls - Ceramic
Popular Sizes.
|
Ceramic Bearings | |
Balls - Ceramic - Silicon Nitride
Outstanding wear resistance. Good thermal and chemical resistance.
|
Balls - Ruby - Synthetic
Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.
|
Balls - Sapphire - Synthetic
Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.
|
Bearings - Ceramic Hybrid
Steel Races - Si 3 N4 Ceramic Balls.
|
Bearings - Ceramic Si3N4
Excellent performance in electrical and magnetism sensitive applications. Higher speed than Zr02.
|
Bearings - Ceramic ZrO2
Excellent performance in electrical and magnetism sensitive applications. Not for High Speed.
|
Ceramic Hybrid Bearings | |
Bearings - Ceramic Hybrid
Steel Races - Si 3 N4 Ceramic Balls.
|
Hobby Bearings - Ceramic Ball
A small selection of popular sizes.
|
Chain - Roller - Metallic | |
Chain - Roller - Metal - Duplex
High tensile steel.
|
Chain - Roller - Metal - Duplex - Links
High tensile steel.
|
Chain - Roller - Metal - Simplex
Includes Stainless Steel and Miniature Sizes.
|
Chain - Roller - Metal - Simplex
Includes Stainless Steel and Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Links
Includes Stainless Steel and Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Links
Includes Stainless Steel and Miniature Sizes.
|
Chain - Roller - Metal - Triplex
High tensile steel.
|
Chain - Roller - Metal - Triplex - Links
High tensile steel.
|
Chain - Roller - Plastic | |
Chain - Roller - Plastic - Single Row
Snap together construction - no joining links required.
|
Sprockets - Roller Chain - Plastic
Nylon - Acetal - With and without bore inserts.
|
Chain and Sprockets | |
Chain - Roller - Metal - Duplex
High tensile steel.
|
Chain - Roller - Metal - Duplex - Links
High tensile steel.
|
Chain - Roller - Metal - Simplex
Includes Stainless Steel and Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Links
Includes Stainless Steel and Miniature Sizes.
|
Chain - Roller - Metal - Triplex
High tensile steel.
|
Chain - Roller - Metal - Triplex - Links
High tensile steel.
|
Chain - Roller - Plastic - Single Row
|
Sprockets - Roller Chain - Metal
With and without hubs.
|
Chain and Sprockets - Ladder | |
Chain - Ladder
Steel - Brass - Stainless - High Tensile.
|
Sprockets - Ladder Chain
With and without hubs. Plastic and Steel.
|
Chamfered Edge Bearings | |
Bearings - Chamfered Edges
Chamfered edge bearings for Linear Guide Systems.
|
Channel | |
Channel - Brass
For general hobby applications.
|
Channel - Safety | |
Mounts - Vibration - Safety Channel
|
Chargers | |
Batteries - Chargers
|
Chrome Steel Balls | |
Balls - Chrome Steel
Hardness: Rockwell C: 60-70.
|
Circlip Pliers | |
Tools - Circlip Pliers - External
External circlip pliers including standard and ratchet type.
|
Tools - Circlip Pliers - Internal
Internal circlip pliers including standard and ratchet type.
|
Tools - Circlip Pliers - Reversible
Reversible circlip pliers for internal and external circlips.
|
Tools - E-Clip Applicators
|
Circlips - External - Basic | |
Circlips - External - Basic
Imperial and metric DIN471 / N1400 / D1460.
|
Circlips - External - Special | |
Circlips - External - Bevelled
1402 / 5102 / VSH / 16630.
A 15 Deg. bevel on the inside diameter to be fitted to a 15% bevel on the load bearing groove wall. Will yield rigid end-play take-up of manufacturing tolerances or wear on the retained part. Used in greasy or oily environments.
|
Circlips - External - Grooveless
Includes MIL-R-21248/MS 90707 - Styles M1440 / Ellison GR / Seeger G and GA.
Reusable tapered section rings for grooveless shafts like plastics, tubes or castings. Can be used where adjustable ring placement is desired - like progressively tightening a compression spring.
|
Circlips - External - Inverted
N1408 / SHI / 16626 / 4100 / 5108 - Spring Steel and Stainless Steel.
Tapered section ring with lugs inverted on the ID to allow use in tight areas with minimal clearance. Less thrust load than standard circlips.
|
Circlips - External - Round Section
DIN7993A / RW / BN825.
Round section wire rings are mostly used in semicircular grooves. Applications include gear systems, automotive engineering and open gudgeon pins.
|
Circlips - External - Tabbed
DIN 983 / D2100 / AK.
External tabs are concentrically positioned for positioning in a concealed assembly. Tabs act as spacers for securing machine components. Conforming to DIN 983.
|
Circlips - Klipring
Also known as Poodle Rings - Imperial - N1504 / NKP
|
Circlips - Internal - Basic | |
Circlips - Internal - Basic
Imperial and metric DIN471 and 472 / N1300 / Seeger J and JS.
Many sizes can also be ordered in Zinc Plated or Stainless Steel. Tolerances on request. Standard and heavy duty options.
|
Circlips - Internal - Special | |
Circlips - Internal - Bevelled
N1302 / VHO / 16631 / 9002 / N5002.
A 15 Deg. bevel on the outside diameter to be fitted to a 15% bevel on the load bearing groove wall. Will yield rigid end-play take-up of manufacturing tolerances or wear on the retained part. Used in greasy or oily environments.
|
Circlips - Internal - Inverted
M1308 / JV / INTV / BN830.
Inverted lugs seat into the groove for better clearance and cleaner appearance. Good for shielded bearings that pass tightly through the bore or housing. Use recommended installation pliers.
|
Circlips - Internal - Round Section
Includes DIN7993B / RB / M1700 / BN826.
Round section wire rings are mostly used in semicircular grooves. Applications include gear systems, automotive engineering and open gudgeon pins.
|
Circlips - Internal - Tabbed
DIN984 / D2000 / Seeger JK.
Internal tabs are concentrically positioned for a concealed assembly. Tabs act as spacers for securing machine components.
|
Circlips - Other | |
C-Clips
Variation of an E-Clip with an open face.
|
Circlips - External - Basic
Imperial and metric DIN471 / N1400 / D1460.
|
Circlips - External - Grooveless
Includes MIL-R-21248/MS 90707 - Styles M1440 / Ellison GR / Seeger G and GA.
|
Circlips - Internal - Basic
Imperial and metric DIN471 and 472 / N1300 / Seeger J and JS.
|
E-Clips - Basic
Basic imperial and metric e-clips DIN6799 and N1500.
|
E-Clips - External Bowed
For end play take up.
|
Push In Retaining Rings - Basic
|
Push On Retaining Rings - Basic
M1465 / DTX / Seeger ZA and KS.
|
Snaprings - External - Basic
Includes series M3200 / SP / ESP / M2400 / SW.
|
Snaprings - Internal - Stainless Steel
|
Circular Pitch Spur Gears | |
Gears - Spur - Circular Pitch 2
PCD = No. of Teeth x 0.636mm (2.000 / Pi.). Various styles and materials.
|
Gears - Spur - Circular Pitch 5
PCD = No. of Teeth x 1.591mm (5.000 / Pi.). Various styles and materials.
|
Clamp Levers | |
Levers - Clamp
|
Clamp Style Shaft Collars | |
Collars - Shaft - Clamp Type
|
Clamp Type Dial Hubs | |
Hubs - Gear and Dial - Single
|
Clamp Type Gear Hubs | |
Hubs - Gear and Dial - Single
|
Clamps - Gear | |
Clamps - Gear - Screw Type
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Clamps - Gear - Split
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Clamps - Gear - Two Piece - Commercial Balanced
Commercial - Stainless - Aluminium - Carbon Steel - For our clamp type gears.
Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. These clamps are designed to clamp the OD of the hub on our clamp type gears. The shaft size listed is for reference only.
|
Clamps - Gear - Two Piece - Precision Balanced
Precision - Stainless - Aluminium - Carbon Steel - For our clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. These clamps are designed to clamp the OD of the hub on our clamp type gears. The shaft size listed is for reference only.
|
Clamps - Gearhead | |
Clamps - Gearhead Attaching
|
Clamps - Shaft | |
Clamps - Shaft
Mild Steel: 045M10. Stainless Steel: 303S21.
|
Clamps - Syncro | |
Clamps - Syncro - Locking
|
Clamps - Syncro - L-Shaped
|
Clamps - Syncro - Mounting - Adjustable
|
Clamps - Syncro - Mounting - Type 1
|
Clamps - Syncro - Mounting - Type 2
|
Clamps - Syncro - Mounting - Type 3
|
Clamps - Syncro - Mounting - Type 4
|
Clamps - Syncro - Mounting - Type 5
|
Clamps - Syncro - Mounting - Type 6
|
Clamps - Syncro - Mounting - Type 7
|
Clamps - Syncro - Mounting - Sintered | |
Clamps - Syncro - Mounting - Sintered
Sintered Stainless Steel 316. Screw Treat Per MIL-S-5002, Clamp as cast and tumbled. Insert - Nylon Type 1 per MIL-M20693, Natural Colour.
|
Clamps - Syncro - Mounting - Type 8 | |
Clamps - Syncro - Mounting - Type 8
|
Clamps for Flexiracks | |
Gears - Racks - Flexible
Blue acetal. Ideal for curved or irregular surfaces. Can fit a bent radius as small as 75mm.
|
Gears - Racks - Flexible - Clamps
For clamping acetal flexirack.
|
Gears - Racks - Flexible - Guide Rails
For mounting flexirack. Flexible nylon or rigid aluminium guide rails.
|
Clean Line Knobs and Handles | |
Handles - Clean Line - Style 1
|
Handles - Clean Line - Style 2
|
Handles - Clean Line - Tubular
|
Knobs - Knurled - Clean Line
|
Knobs - Lobe - Clean Line
|
Clean Room Linear Slides | |
Slides - Linear - Clean Room
|
Cleaning Products | |
Cleaning Products - Miscellaneous
Products related to bearing and power transmission work. No overseas sales.
Some items in this category are marked as only available for collection.
|
Clevis Joints | |
Joints - Clevis - Plastic
Use with plastic rod ends - Includes pin and clip.
|
Joints - Clevis - Spring Clips
Made from 9SMn steel.
|
Joints - Clevis - Stainless Steel
|
Joints - Clevis - Steel
Made from zinc plated 9SMn steel.
|
Clevis Pins | |
Joints - Clevis - Spring Clips
Made from 9SMn steel.
|
Clips | |
C-Clips
Variation of an E-Clip with an open face.
|
Circlips - External - Basic
Imperial and metric DIN471 / N1400 / D1460.
|
Circlips - External - Grooveless
Includes MIL-R-21248/MS 90707 - Styles M1440 / Ellison GR / Seeger G and GA.
|
Circlips - Internal - Basic
Imperial and metric DIN471 and 472 / N1300 / Seeger J and JS.
|
E-Clips - Basic
Basic imperial and metric e-clips DIN6799 and N1500.
|
Pins - Hitch - External
Also known as R-Clips.
|
Pins - Hitch - Internal
|
Push In Retaining Rings - Basic
|
Push On Retaining Rings - Basic
M1465 / DTX / Seeger ZA and KS.
|
Snaprings - External - Basic
Includes series M3200 / SP / ESP / M2400 / SW.
|
Snaprings - Internal - Stainless Steel
|
Clips - E | |
Hobby E-Clips
A small selection of popular sizes.
|
Clips - R | |
Pins - Hitch - Internal
|
Closed Linear Bearings | |
Bearings - Linear - Ball
Adjustable and fixed types - open for running on a supported rail and closed for fixed shafts.
|
Bearings - Linear - Ball - Thomson Precision Steel (Closed)
For running on shafts fixed at the ends.
|
Bearings - Linear - Ball - Thomson Super (Closed)
For running on shafts fixed at the ends.
|
Bearings - Linear - Ball - Thomson Super Smart (Closed)
For running on shafts fixed at the ends.
|
Housings - Linear - Thomson Super (Twin Pillow Block - Closed)
Includes Bearings.
|
Housings - Linear - Thomson Super Smart (Pillow Block - Closed)
Includes Bearings.
|
Cluster Gears and Press On Gears to Suit | |
Gears - Cluster - 48 Pitch
Have a mounting area for a second gear - see diagram.
|
Gears - Cluster - 64 Pitch
Have a mounting area for a second gear - see diagram.
|
Gears - Cluster - 72 Pitch
Have a mounting area for a second gear - see diagram.
|
Gears - Cluster - 80 Pitch
Have a mounting area for a second gear - see diagram.
|
Gears - Spur - 24 Pitch - Hub Mounting
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
|
Gears - Spur - 32 Pitch - Hub Mounting
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
|
Gears - Spur - 48 Pitch - Hub Mounting
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
|
Gears - Spur - 64 Pitch - Hub Mounting
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
|
Gears - Spur - 72 Pitch - Hub Mounting
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
|
Gears - Spur - 80 Pitch - Hub Mounting
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
|
Gears - Spur - 96 Pitch - Hub Mounting
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
|
Gears - Spur - 120 Pitch - Hub Mounting
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
|
Clutch Assemblies | |
Clutch Assemblies - Slip - Precision
Adjustable Torque range 360-3600 g.cm (5-50 oz.in).
303 Stainless Steel. Brake : Oil Impregnated Bronze. Use with hubless gears with 9.525 bore and 3.175 face width.
|
Clutch Assemblies - Slip - Standard
Adjustable Torque range 360-3600 g.cm (5-50 oz.in).
Adjustable Torque. 303 Stainless Steel with Cork Brake Material. Use with hubless gears with 9.525 bore and 3.175 face width.
|
Clutch Bearings | |
Bearings - One Way - Roller
Roller Clutch Bearings rotate in one direction only.
|
Bearings - One Way - Sprag - BR
Sprag clutch bearings allow your application to turn one way whilst locking in the opposite direction.
|
Bearings - One Way - Sprag - Standard
Sprag clutch bearings allow your application to turn one way whilst locking in the opposite direction.
|
Bearings - One Way - Sprag - TFS
Sprag clutch bearings allow your application to turn one way whilst locking in the opposite direction.
|
Bearings - One Way - Sprag - TSS
Sprag clutch bearings allow your application to turn one way whilst locking in the opposite direction.
|
Clutch Bearings - Roller - Hobby | |
Hobby Bearings - Roller Clutch
Roller Clutch Bearings rotate in one direction only. Drawn Cup Type.
|
Clutch Brakes | |
Clutch Brakes - Magnetic - Bu-Ord Size 11
Breakaway Torque (Energised) at 24-28 V DC : 10.8g.cm (0.15 oz.in). Breakaway Torque (De-Energised) at 24-28 V DC : 3.6g.cm (0.05 oz.in). Shafts A & B coupled when energised, B shaft braked when de-energised. Inertia (De-Energised) at 24-28 VDC : 2.38g.cm sq (0.013 oz.in sq). Inertia (Energised) at 24-28 VDC : 5.3g.cm sq (0.029 oz.in sq).
|
Clutch Brakes - Magnetic - Bu-Ord Size 11 - Reverse Acting
Breakaway Torque (Energised) at 24-28 V DC : 18g.cm (0.25 oz.in). Breakaway Torque (De-energised) at 24-28 V DC : 7.2g.cm (0.10 oz.in). Shafts A & B coupled when de-energised, braked when energised. Inertia (De-Energised) at 24-28 VDC : 7.4g.cm sq (0.041 oz.in sq). Inertia (Energised) at 24-28 VDC : 5.1g.cm sq (0.028 oz.in sq).
|
Clutch Brakes - Magnetic - Bu-Ord Size 18
Breakaway Torque (Energised) at 24-28 V DC : 14.4g.cm (0.20 oz.in). Breakaway Torque (De-Energised) at 24-28 V DC : 2.2g.cm (0.03 oz.in). Shafts A & B coupled when energised, B shaft braked when de-energised. Inertia (Energised) at 24-28 VDC : 5.11g.cm sq (0.071 oz.in sq). Inertia (Energised) at 24-28 VDC : 7.56g.cm sq (0.105 oz.in sq).
|
Clutch Brakes - Magnetic - Bu-Ord Size 18 - Reverse Acting
Breakaway Torque (Energised) at 24-28 V DC : 3.6g.cm (0.05 oz.in). Breakaway Torque (De-Energised) at 24-28 V DC : 14.4g.cm (0.2 oz.in). Shafts A & B coupled when de-energised, braked when energised. Inertia (De-Energised) at 24-28 VDC : 7.27g.cm sq (0.101 oz.in sq). Inertia (Energised) at 24-28 VDC : 5.11g.cm sq (0.071 oz.in sq).
|
Clutch Couplings | |
Couplings - Clutch - Flange Mounted
0.565 to 14 N.m. For in-line loads.
|
Couplings - Clutch - Shaft Mounted
0.565 to 14 N.m. For in-line loads.
|
Clutches - Flange Mounted | |
Clutches - Flange Mounted
24 V DC. Zero backlash armature. For parallel loads.
|
Clutches - Friction | |
Clutches - Friction - Polyclutch
Backlash of 6° is standard; 2° backlash available on request. Adjustable Torque.
|
Clutches - Friction - Slip Ease
ADJUSTABLE TORQUE - For shaft to shaft coupling. Set screw housings in both housing and cartridge. SLIP-EASE utilises an axial loaded multi-plate design. For applications where space is at a premium and low backlash is required. Backlash of 2° as standard.
|
Clutches - Magnetic | |
Clutches - Combinorm - Power On
Applying a standard 24 V DC the armature is attracted by the force of a magnetic field. This results in a frictionally engaged connected (for single-face elements). or a positive-locking connection (for tooth clutches).
|
Clutches - Magnetic - Bu-Ord Size 11
Breakaway Torque (Energised) at 24-28 V DC : 10.8g.cm (0.15 oz.in). Breakaway Torque (De-Energised) at 24-28 V DC : 3.6g.cm (0.05 oz.in). Shafts A & B coupled when energised, braked when de-energised. Inertia (De-Energised) at 24-28 VDC : 0.94g.cm sq (0.013 oz.in sq). Inertia (Energised) at 24-28 VDC : 2.09g.cm sq (0.029 oz.in sq).
|
Clutches - Magnetic - Bu-Ord Size 11 - Reverse Acting
Breakaway Torque (Energised) at 24-28 V DC : 18g.cm (0.25 oz.in). Breakaway Torque (De-energised) at 24-28 V DC : 7.2g.cm (0.10 oz.in). Shafts A & B coupled when de-energised, braked when energised. Inertia (De-Energised) at 24-28 VDC : 7.4g.cm sq (0.041 oz.in sq). Inertia (Energised) at 24-28 VDC : 5.0g.cm sq (0.028 oz.in sq).
|
Clutches - Magnetic - Bu-Ord Size 11 - Triplex
Breakaway Torque (Energised) at 24-28 V DC : 14.4g.cm (0.20 oz.in). Breakaway Torque (De-energised) at 24-28 V DC : 4.3g.cm (0.06 oz.in). Shafts A & B coupled when energised (terminals 1 and 2). Shafts A & C coupled when energised (terminals 3 and 4). Inertia (Energised) at 24-28 VDC : 8.0g.cm sq (0.045 oz.in sq) either coil, 10.7g.cm sq (0.060 oz.in sq) both coils.
|
Clutches - Magnetic - Bu-Ord Size 18
Breakaway Torque (Energised) at 24-28 VDC : 14.4g.cm (0.20 oz.in). Breakaway Torque (De-Energised) at 24-28 VDC : 4.3g.cm (0.06 oz.in). Shafts a & B coupled when energised, braked when de-energised. Inertia (De-Energised) at 24-28 VDC : 2.74g.cm sq(0.038 oz.in sq). Inertia (Energised) at 24-28 VDC : 5.18g.cm sq (0.072 oz.in sq).
|
Clutches - Magnetic - Bu-Ord Size 18 - Reverse Acting
Breakaway Torque (Energised) at 24-28 VDC : 3.6g.cm (0.05 oz.in). Breakaway Torque (De-Energised) at 24-28 VDC : 14.4g.cm (0.2 oz.in). Shafts A & B coupled when de-energised, braked when energised. Inertia (De-Energised) at 24-28 VDC : 19g.cm sq (0.134 oz.in sq). Inertia (Energised) at 24-28 VDC : 5.18g.cm sq (0.103 oz.in sq).
|
Clutches - Magnetic - Bu-Ord Size 18 - Triplex
Breakaway Torque (Energised) at 24-28 VDC : 14.4g.cm (0.20 oz.in). Breakaway Torque (De-Energised) at 24-28 VDC : 4.3g.cm (0.06 oz.in). Shafts A & B coupled when energised (terminals 1 and 2). Shafts A & C coupled when energised (terminals 3 and 4). Inertia (Energised) at 24-28 VDC : 19.2g.cm sq (0.108 oz.in sq) either coil, 25.86g.cm sq (0.145 oz.in sq) both coils.
|
Clutches - Magnetic Particle 24VDC
Ultrafast Responses.
The input shaft becomes coupled to the output shaft with electrical excitation. Shafts have a flat on the end. Soft or fast start.
|
Clutches - Roller - One Way | |
Bearings - One Way - Roller
Roller Clutch Bearings rotate in one direction only.
|
Clutches - Shaft Mounted | |
Clutches - Shaft Mounted
24 V DC - Zero Backlash Armature - For parallel loads.
This basic information is designed to assist you to make a decision on which clutch to use. Full dimensions available on request.
|
Clutches - Slip | |
Clutches - Slip - Inline
Multiplate Design.
Fully adjustable within rating limits. Low stick / slip ratio. Continuous slip within dissipation limit. Zinc plated steel housing with brass plates. Proprietary non-asbestos friction material.
|
Clutches - Slip - Inline - Precision
Adjustable to 3600 g.cm (50 oz.in) by advancing jam nut and using second jam nut to lock. Adjustment with 7/8 open end wrench (not supplied). Pin and Clamp type hubs.
|
Clutches - Slip - Magnetic Particle - Integral Shaft - No Power
Requires no power.
Sealed from contamination. Uses permanent magnets and magnetic particles. Constant torque levels. Zero maintenance - Long operational life. See PDF sheet at bottom of this page.
|
Clutches - Slip - Magnetic Particle - No Power
Requires no power.
Sealed from contamination. Uses permanent magnets and magnetic particles. Constant torque levels. Zero maintenance - Long operational life. See PDF sheet at bottom of this page.
|
Clutches - Slip - Spring Wrapped
|
Coil | |
Solarbotics Miscellaneous
Coils and Trimpot.
|
Cold Rolled Steel | |
Shim - Steel
Shim sheet. Cold rolled steel. Very thin to thick sizes.
|
Collars - Shaft | |
Collars - Shaft - Clamp Type
|
Collars - Shaft - D-Bore
|
Collars - Shaft - Fairloc
|
Collars - Shaft - Gripfast
Self Locking - Quick Release.
265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs.
|
Collars - Shaft - Hinged Type
Precision machined. Convenient easy-to-assemble design.
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
|
Collars - Shaft - Standard
Includes miniature precision types. Carbon steel, 303 and 316 stainless.
|
Collars - Shaft - Stroke Adjustment
Recommended tolerances for mating shaft diameter : h6. Use with rubber washers listed under WASHERS.
|
Collars - Shaft - With Integral Shim
Bore tolerance (+0.003/+0.013). Imperial Collars have undersized tolerances. Metric Collars have oversized tolerances.
|
Commercial Hobby Washers | |
Hobby Washers - Commercial
A small selection of popular sizes.
|
Compression Springs | |
Springs - Compression
|
Springs - Compression - Metre Lengths
|
Cone Point Socket Set Screws | |
Socket Set Screws - Cone Point
|
Conical Bumpers | |
Bumpers - Conical
Anti vibration application for machinery.
|
Conical Vibration Mounts | |
Mounts - Vibration - Conical
|
Connecting Links - Roller Chain | |
Chain - Roller - Metal - Simplex - Links
Includes Stainless Steel and Miniature Sizes.
|
Constant Force Springs | |
Spring Assemblies - Bracket - RINO
|
Spring Assemblies - Single - RINO
|
Spring Assemblies - Twin - RINO
|
Spring Motor Assemblies - Closed - RINO
Budget Assemblies. Average fatigue life of 30,000 cycles.
|
Spring Motor Assemblies - SDP
Base Mounted.
|
Spring Motors - RINO
|
Spring Motors - SDP
|
Springs - Constant Force
|
Constant Natural Frequency Mounts | |
Mounts - Uniload - CNF - Heavy Duty
Constant Natural Frequency Mounts - Stiffness is proportional to load.
|
Mounts - Uniload - CNF - Medium Duty
Constant Natural Frequency Mounts.
|
Construction Materials - Robotic | |
Solarbotics Materials
Versatile material for building robots because of its ability to glue well with epoxy and superglue.
|
Construction Sets | |
Engineering Sets - Educational
Educational engineering / construction sets. Simple build yourself kits.
|
Control Flex Couplings | |
Couplings - Control Flex. 0.45 to 6.44 Nm.
|
Control Handles | |
Levers - Control Handles
|
Levers - Control Handles - Flat
|
Conveyor Bearings | |
Bearings - Conveyor - Hex Bore
Plastic and Stainless Steel.
|
Copper | |
Mesh - Various
|
Tube - Round - Copper
For general hobby applications.
|
Copper Shim | |
Shim - Copper
Shim sheet. Very thin to thick sizes.
|
Cord - Rubber | |
O-Rings - Cord
Nitrile and Fluoroelastomer continuous length o-ring cord.
|
Cotter Pins | |
Pins - Cotter - Plain
Split pins.
|
Pins - Cotter - Stainless Steel
Split pins.
|
Pins - Cotter - Zinc Plated
Split pins.
|
Countersunk Flat Head Screws | |
Hobby Screws - Countersunk Head
A small selection of popular sizes.
|
Screws - Machine - Nylon - Countersunk Head
Flat Head Countersunk UNC and UNF.
|
Screws - Machine - Steel - Countersunk Head
Flat Head Countersunk UNC - UNF - BA - METRIC - Zinc Plated - Brass and Plain - Various Head Types.
|
Screws - Machine - Titanium CP1 - Countersunk Head
Flat Head Countersunk. CP Grade 1 Titanium.
|
Screws - Security - Socket - Countersunk
|
Screws - Security - Two Hole - Countersunk
|
Screws - Self Tapping - Countersunk Head
|
Screws - Socket - Countersunk - Aluminium
Flat Head Countersunk UNC - UNF - METRIC.
|
Screws - Socket - Countersunk - Stainless Steel
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
|
Screws - Socket - Countersunk - Steel
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
|
Countersunk Head Screws | |
Hobby Screws - Socket Countersunk
A small selection of popular sizes.
|
Countersunk Head Self Tapping Screws | |
Screws - Self Tapping - Countersunk Head
|
Countersunk Head Socket Screws | |
Screws - Machine - Nylon - Countersunk Head
Flat Head Countersunk UNC and UNF.
|
Screws - Machine - Steel - Countersunk Head
Flat Head Countersunk UNC - UNF - BA - METRIC - Zinc Plated - Brass and Plain - Various Head Types.
|
Screws - Socket - Countersunk - Steel
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
|
Couplings - Ball | |
Couplings - Ball
High Speed - Up to 15 Degrees Angular Offset. 0.17 to 22.6 N.m Torque. Up to 20,000 rpm.
Speed Ratings :. 20000 RPM at up to 5 Degree Operating Angle. 10000 RPM at 6 to 10 Degree Operating Angle (Torque Reduction 50%). 5000 RPM at 11 to 15 Degree Operating Angle (Torque Reduction 66%). Nylon centred units provide electrical insulation between shafts.
|
Couplings - Bantam | |
Couplings - Bantam - Complete
Isolates vibration up to 85%. Sleeve provides electrical insulation. 0.21Nm at 1725rpm.
Parallel Offset 0.25 mm. Angular Offset 1.5 Degree.
|
Couplings - Bantam - Components
Isolates vibration up to 85%. Sleeve provides electrical insulation. 0.21Nm at 1725rpm.
Parallel Offset 0.25 mm. Angular Offset 1.5 Degree.
|
Couplings - Bellows | |
Couplings - Bellows
Zero Backlash - Constant Velocity Ratio - Low Inertia. 0.85 to 2.0 Nm. 2000 to 20,000rpm.
|
Couplings - Bellows - Hiflex
Precise adjustment - Vibration resistance - Large misalignment capability. 0.01 to 9.17 Nm. 2000 rpm.
Zero Backlash. Wide torque range. Zero cyclic speed variation during 360 Deg. Rotation. Very low torsional deflection.
|
Couplings - Bellows - Modular
Interchangeable bushings for a variety of bore sizes.
1 Coupling consists of: 2 Bushings - 2 Clamps - 1 Bellows. Choose all 5 parts from any one size group. Bushings may be interchanged within any size group.
|
Couplings - BoWex - Junior | |
Couplings - BoWex - Junior
Nylon 2 piece and 3 piece couplings. 5 to 24 Nm. 6000 rpm max.
Approved distribution through the Australian Wholesaler (Deanquip). Crowned gear teeth - No need for lubrication. Chemical resistant nylon. Electrically insulated. Grub Screw opposite Keyway.
|
Couplings - Clutch | |
Couplings - Clutch - Flange Mounted
0.565 to 14 N.m. For in-line loads.
24 Volt DC. Zero Backlash Armature. For in-line loads. Dynamic torque is 80% of static torque. 0.565 N.m Models have no set screws in rotor - pin hole only.
|
Couplings - Clutch - Shaft Mounted
0.565 to 14 N.m. For in-line loads.
24 Volt DC. Zero Backlash Armature. For in-line loads. Dynamic torque is 80% of static torque. 0.565 N.m Models have no keyway in rotor.
|
Couplings - Control Flex | |
Couplings - Control Flex. 0.45 to 6.44 Nm.
MATERIALS: Hubs - Aluminium, Pins - Hardened Alloy Steel, Socket Head Screws - Alloy Steel, Control-Flex Member - Delrin® 100. Lightweight, low inertia, and no maintenance or lubrication necessary. No change in angular velocity or torque due to misalignment. No end thrust due to torque transmission. Rated torques are with all alignment factors zero. The summation of the three alignment factors should not exceed 50%. The rated torque must be reduced by the summation of the alignment factors. Operating Temperature: -23 deg to +65 deg Celsius.
|
Couplings - Cross Joint | |
Couplings - Cross Joint. 0.5 to 10 N.m. 3600 to 6000 rpm.
Bushings - Dry Bush Bearing. Stainless Steel Spacers. Steel Pins. Aluminium Alloy Hubs.
|
Couplings - Crowned Tooth | |
Couplings - Crowned Tooth Gear Type. 19.55 to 88 Nm. 8500 to 14000 rpm.
Steel hubs with Moulded Nylon Sleeve.
+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1 Degree Angular Displacement. Free axial movement. High torque / low inertia.
|
Couplings - Double Disk | |
Couplings - Double Disk - High Torque. 2.8 to 22 Nm. 2400 to 4800 rpm.
Zero Backlash - Clamp Locking - Medium torsional stiffness.
High torsional stiffness and high response. Zero backlash. Hub: Aluminium (A2017) Spacer: Aluminium (A2011). Pin: Stainless Steel (SUS301) Disk: Stainless Steel (SUS303). Maximum Temperature: +100°C. Identical clockwise & anti-clockwise rotational characteristics.
|
Couplings - Double Disk. 0.7 to 12.5 Nm. 3000 to 19000 rpm.
Zero Backlash - High Torsional Stiffness.
Hub and Spacer: Aluminium Alloy. Pin and Disc: Stainless Steel. Max Axial Play: +/-0.5mm.
|
Couplings - Flexible-Shaft | |
Couplings - Flexible-Shaft Type
Nonmagnetic flexible shaft couplings. Max torque 0.39 Nm.
Maximum Torque 0.39 N.m (3.5 lb.in). Minium operating radius 89 mm (3.5 in.). Torsional deflection 1.8 Deg per lb.in per inch (25mm) of shaft in Winding Direction. Torsional deflection 2.6 Deg per lb.in per inch (25mm) of shaft in Unwinding Direction. Cadmium Plated Brass Ends - Phosphor Bronze Cable - 300 Series Stainless Screws.
|
Shafts - Flexible - Coupling Ends - Cased
|
Shafts - Flexible - Coupling Ends - Open (SDP)
Flexible shafting with coupling ends ready to attach to a fixed shaft.
|
Shafts - Flexible - Panel Mount - Cased
|
Shafts - Flexible - Panel Mount - Open
|
Couplings - Geargrip | |
Couplings - Geargrip
0.67 to 6.78 Nm. Max speed 3000 rpm.
Sleeve - Neoprene with Ground OD; Hub - Zinc Alloy Die Casting. Suitable operating temperature is -28 to 70 Deg. Celsius. Features: no lubrication, electrically isolated, dampens shock and vibration.
|
Couplings - Helical | |
Couplings - Helical - Long Series
2.9 to 31.4 Nm.
5 Degree max angular misalignment. 0.762 mm Parallel offset. +/- 0.254 mm Axial motion. Zero backlash.
|
Couplings - Helical - Low Inertia
0.8 to 13.2 Nm.
5 Degree max angular misalignment. 0.254 mm Parallel offset. +/- 0.203 mm Axial motion. Zero backlash.
|
Couplings - Helical - Precision
0.14 to 9 Nm. 25000 max RPM.
5 Degree max angular misalignment. 0.076 mm Parallel offset. Zero Axial motion. Zero backlash.
|
Couplings - Helical - Short - Ondrives
Material: 303 S3U Stainless.
|
Couplings - Helical - Standard
0.1 to 16.2 Nm.
Zero backlash. Max. Ang Misalignment 5 Degrees. Max Parallel Offset 0.25mm.
|
Couplings - Hobby | |
Hobby Couplings - Jaw Type
A small selection of jaw type couplings.
|
Hobby Couplings - Junior
A small selection of nylon junior couplings.
|
Hobby Couplings - Spider Type
A small selection of spider type couplings.
|
Couplings - Jaw Type | |
Couplings - Jaw Type - With Acetal Spider
Max 1800 RPM. 0.5 to 2.96 Nm.
Angular Offset = 0.1 Deg. Max. Parallel Offset = 0.381mm Max. Fibreglass Hubs - Acetal Spider.
|
Couplings - Jaw Type - With Polyurethane Spider
Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm.
Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application.
|
Couplings - Jaw Type - With Rubber Spider
Max 3600 RPM. 0.39 to 16.27 Nm.
Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM.
|
Couplings - K Type | |
Couplings - K Type
Up to 3600 RPM - Minus 20 to Plus 60 Degrees C. 0.34 to 18 Nm.
Strong, flexible polyurethane or Hyrtel® is cut and tear resistant. Up to 3600 RPM. Urethane: Minus 20 to Plus 60 Degrees C / Hyrtel® : Minus 40 to Plus 100 Degrees C. Precision swaged mechanically crimped hubs. Annealed steel hubs.
|
Couplings - Multi-jaw | |
Couplings - Multijaw - Precision
Max Torque 3.5 Nm.
303 Stainless Steel. Stainless socket set screws supplied. 48 teeth - 64 Pitch. Max Torque 3.5 N.m (500 oz.in).
|
Couplings - Neo-Flex | |
Couplings - Neo-Flex
0.71 to 1.27 Nm.
303 stainless steel with 73 durometer neoprene centre. Shaft to shaft insulation. Torsional vibration isolation. Ribbed style are more flexible than smooth style. Bore Tolerances: +0.025 / -0.000.
|
Couplings - Oldham | |
Couplings - Oldham - Complete
0.06 to 44 Nm. Max Speed: 3000 RPM.
Max Speed: 3000 RPM. Parallel out of line compensation. Temp Range -20 Deg C to +60 Deg C. Disk Material: Acetal.
|
Couplings - Oldham - Components
0.06 to 44 Nm. Max Speed: 3000 RPM.
|
Couplings - Oldham - Precision Spring Loaded
2.8 to 4.2 Nm. Max Speed: 3000 RPM.
Max Speed: 3000 RPM. Max Backlash: 5 minutes. Max parallel shaft offset: 0.381mm. Max angular offset: 1.5 Degrees. 303 Stainless Steel.
|
Couplings - Rigid | |
Couplings - Rigid
0.35 to 5.1 Nm.
Quality Class Precision: Bore Tolerance +0.013 / - 0.000 concentric within 0.0127mm T.I.R. Quality Class Commercial: Bore Tolerance +0.051 / -0.000.
|
Couplings - Single Disk | |
Couplings - Single Disk
0.7 to 19 Nm. 2400 to 10000 rpm.
High response. High torque. Zero backlash. High torsional stiffness.
|
Couplings - Sleeve | |
Couplings - Sleeve Type
0.05 to 2.1 Nm. Max Speed 1750 rpm.
Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.
|
Couplings - Slip | |
Couplings - Slip - Spring Wrapped
Tension control - transmission overload protection. 0.035 to 1.69 Nm.
Coupling is sliped over one shaft and screws tightened. Second shaft is inserted into other end. Loose end of coupling is pulled back about 0.5mm then screws tightened. Serves as a torque limiter as well as a coupling. Long life under continuous slip applications.
|
Couplings - Slit | |
Couplings - Slit Type
Aluminium - Stainless Steel - Flexible - Zero Backlash. 0.1 to 35 Nm. 2400 to 48000 rpm.
High Torsional Stiffness. Zero Backlash.
|
Couplings - Spider | |
Couplings - Spider Type
2.1 to 17 Nm.
Split Type Hub. Preloaded Rubber Spider. Minimal backlash. Choice of 3 different spiders for each size provides for different torque requirements. Hubs and spiders available separately or as a complete unit.
|
Couplings - Spiral Beam | |
Couplings - Helical - Long Series
2.9 to 31.4 Nm.
|
Couplings - Helical - Low Inertia
0.8 to 13.2 Nm.
|
Couplings - Helical - Precision
0.14 to 9 Nm. 25000 max RPM.
|
Couplings - Helical - Standard
0.1 to 16.2 Nm.
|
Couplings - Slit Type
Aluminium - Stainless Steel - Flexible - Zero Backlash. 0.1 to 35 Nm. 2400 to 48000 rpm.
|
Couplings - Spiral Beam - 6 Beam
Pilot Bore size not toleranced. Finished Bore sizes to +0.03/0.00.
|
Couplings - Spline | |
Couplings - Spline Type
0.5 to 4.5 Nm. 12000 to 24000 rpm.
Angular Misalignment: 2 Deg. Parallel Offset: 0.2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 deg C.
|
Couplings - Spring | |
Couplings - Spring
1.4 Nm Max Torque.
303 Stainless Spring. Aluminium Alloy Hub. High angular displacement of 20 degrees. Protects gear and timing drives from excessive shock loads. Suitable for high speed drives.
|
Couplings - Torque Tube | |
Couplings - Torque Tube
Internal compression spring preloads the ends against axial movement and backlash. Up to 2.8 Nm. Up to 2000 rpm.
Maximum Torque: 2.8 N.m (25 lb.in). Delrin Torque Tube. Aluminium Split Hubs. Do not compress the unit axially during installation. Speeds to 2000 rpm. One piece assembly.
|
Couplings - Uniflex | |
Couplings - Uniflex
High speed to 30000 rpm. 2.3 to 9.27 Nm.
Spring : 1095 Steel Hubs : Cold Rolled Steel. Operating Temperature : 121 Deg C (250 Deg F). Maximum Speed : 30000 RPM. For CUF15 series the spring diameter is the same as the hub diameter.
|
Couplings - Uni-lat | |
Couplings - Uni-lat
0.3 to 3.5 Nm. 3000 to 6000 rpm.
Hubs (UNL18 & 27): Brass CZ 121 Chromate & passivate finish. Hubs (UNL34 & 41):Alum. Alloy 2011 T8 Alocrom finish. Bearing Rings: Black Acetal. Operating Temp. Range: -20°C to +60°C. 10° angular and 1mm radial compensation. Flex-free mechanical action - low bearing loads.
|
Couplings - Universal Joint | |
Universal Joints - Inverted Design
|
Universal Joints - Inverted Design - Telescoping
|
Universal Joints - Steel
Steel - Cast Zinc - Stainless Steel.
|
Universal Joints - Telescoping - Moulded
|
Universal Joints - Telescoping - Spline Type - Stainless Steel
|
Universal Joints - Telescoping - Zero Backlash
|
Covers - Universal Joint | |
Covers - Universal Joint - Elasticate Rubber
For Single and Double Universal Joints.
-27 Deg C to 70 Deg C temp range (constant). -32 Deg C to 120 Deg C temp range (intermittent).
|
Covers - Universal Joint - Neoprene Rubber
For Single and Double Universal Joints.
-27 Deg C to 70 Deg C temp range (constant). -32 Deg C to 120 Deg C temp range (intermittent).
|
Cranks - Hand | |
Cranks - Hand
Precision hand cranks.
2024 Aluminium Black Anodised.
|
Cranks - Handwheel - Solid - Metal
Light metal casting. Surface Finish: All edges turned and polished. Hub machined and bored to ISO fit H7.
|
Cranks - Handwheel - Solid - Plastic - No Grip
Duroplastic FS 31 black. Bush in Steel, Bright and Lubricated.
Surface Finish: All edges smoothed and highly polished.
|
Cranks - Handwheel - Solid - Plastic - With Grip
Duroplastic FS31 black. Bush in Steel, Bright and Lubricated.
Duroplastic FS31 black. Bush in Steel, Bright and Lubricated. Surface Finish: All edges smoothed and highly polished. Handwheel and taper grip will be delivered unassembled. All models include taper grip.
|
Cranks - Handwheel - Spoked
Pressed steel with RAL 9005 black epoxy resin coating. Hub: Welded with H9 tolerance plain hole (Type B) or through square H11 tolerance hole (Type V). Axial and radial runout lower than IT 12.
|
Cranks - Handwheel - Spoked - With Handle
AISI 304 pressed stainless steel with sand blasted matte finish. Hub: Welded with H9 tolerance plain hole (Type B) or through square H11 tolerance hole (Type V). Axial and radial runout lower than IT 12. Black duroplastic revolving handle.
|
Crimping Tool - Synchromesh | |
Tools - Crimping
For crimping loop sleeves, plugs and eyes used with miniature cable.
|
Cross Joint Couplings | |
Couplings - Cross Joint. 0.5 to 10 N.m. 3600 to 6000 rpm.
|
Crossed Roller Way | |
Crossed Roller Way
For precise linear motion.
Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100°C ( Constant), +140°C (Maximum). For temperatures over 100°C we can supply special high temperature grease (200°C - supplied in syringe) CG2-SY.
|
Crowned Tooth Gear Type Couplings | |
Couplings - Crowned Tooth Gear Type. 19.55 to 88 Nm. 8500 to 14000 rpm.
Steel hubs with Moulded Nylon Sleeve.
|
Cup Style Mounts | |
Mounts - Cup Style
|
Cup Washers - Brass | |
Washers - Cup - Brass
For countersunk screws.
|
Curved Spring Washers | |
Washers - Disc Spring - Steel
Includes Carbon Steel and Stainless Steel
|
Washers - Spring
Wave Washers - All Materials.
|
Cutting and Threading | |
Tools - Die Holders
Bar and round holders. 16mm, 20.64mm and 25.4mm (inch).
|
Tools - Dies
Tungsten Chrome Alloy - Carbon Steel. Button dies and die nuts starting from M1 and 0-80 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.
|
Tools - Drill Bits
Micro miniature drill bits starting from 0.32mm up to larger standard sizes. Sutton - PN - Bordo.
|
Tools - Tap Wrenches
Tee handle and bar types. Suit taps from 1mm to 12mm.
|
Tools - Taps
High Speed Steel Short Machine and Carbon Steel Straight Flute Taps. starting from M1 and 0-90 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.
|
Cylindrical Mounts | |
Mounts - Vibration - Cylindrical
|
|
